Search Documents

By J. Alton Burks, Roy C. Bartholomae

The chain conveyor is utilized extensively in underground mining to convey raw ore, especially coal. It is estimated that several thousand loading and continuous mining machines rely on this type of conveyance. Although the chain conveyor is both efficient and highly reliable, its use is generally associated with the production of noise levels that often exceed 105 dBA at the operator's position. Thus, it is one of the most significant contributors to the occupational noise problem experienced by miners in the underground coal mining environment. Conventional engineering noise controls that result in an average reduction of 4 dBA have been previously designed and implemented. However, a novel solution involving a change in conveyor operation has been proposed that takes advantage of two aspects of conveyor noise: 1) conveyor noise has an approximately cubic dependence on conveyor chain speed and 2) due to the damping provided by coal, a full conveyor is 5 dBA quieter than an empty one. An engineering analysis has shown that a significant reduction in the operating noise level of a typical continuous miner can be achieved through the use of an adjustable speed drive automatically controlled by a coal loading sensor that maintains a full conveyor at all times. The potential reduction depends primarily on the mining conditions (coal seam thickness and the presence of either rock or water) and varies from 7-18 dBA. Other benefits to be derived from the use of a variable speed drive include reductions in power consumption, dust, and maintenance costs.

Jan 1, 1992

By Gaither H. Kitchell

Introduction Fire assaying is an ancient method of determining the amount of gold and silver in geological materials. Today's commercial, mining, school, and private fire assaying laboratories still use this basic assaying method. One of the primary reagents used to collect gold and silver from the ore is litharge (PbO), or lead oxide. The Federal Occupational Safety and Health Administration's (OSHA) and the Nevada Division of Occupational Safety and Health's (OSH) have a lead standard. It states that a person exposed to airborne lead at concentrations greater than 50 µg/m3 (1.4 µg per cu ft) of air over an eight-hour period has gone beyond the permissible limit for health safety. It is not uncommon to get airborne lead concentrations of 1400 µg/m3 (40 µg per cu ft) in the flux/sampling area or 900 µg/m3 (25 µg per cu ft) around the gas/ electric furnaces during the fusion and cupelling phases. Therefore, any individual working in these areas for more than 30 days per year without proper protection is a likely candidate for lead poisoning. Lead In A Human Lead enters the body as a toxic substance by breathing it into the lungs and upper respiratory tract and by getting lead particles into the digestive system through ingestion. Smoking, eating, drinking, chewing tobacco and gum, or wiping a lead-contaminated hand across the mouth are all potential ways forgetting lead into the body. Lead taken in large quantities can actually kill a person in a matter of days. This is rare, however. The real hazard of lead overexposure is for the unsuspecting person who works in an unsafe lead environment for months or years. This individual can slowly receive damage, sometimes permanent, to the central nervous system, gastrointestinal tract, kidneys, blood, gums, and reproductive system. Safe Blood-Lead Level The Lead Standard states that the maximum safe blood-lead level is 40 µg/100 g (40 µg per 3.5 oz) of whole blood. It recommends 30 µg/100 g (30 µg per 3.5 oz) if a person is of child-bearing age. People not working around lead products normally have a blood level of less than 10 µg/100 g (10 µg per 3.5 oz). A person not adequately protected can exceed 40 µg/100 g (40 µg per 3.5 oz) in a few weeks by fire assaying only 100 samples per day per week. Studies show that some individuals have developed lead-related diseases with blood-lead levels less than 80 µg/m3 (2.3 µg per cu ft). Lead Poisoning Symptoms There is a long list of symptoms associated with lead poisoning. The most common are: a prolonged, sweet, metallic taste in the mouth; loss of appetite; anxiety and irritability; weakness and dizziness; nausea and tremors; and insomnia. Preventive Measures Based on the lead standard, a number of preventive measures can be taken to ensure that fire assay laboratory personnel frequently exposed to lead are protected against overexposure. First, the actual lead concentration within the assaying area should be determined. In Nevada, one can contact the Department of Industrial Relations, Division of Occupational Safety and Health for assistance in monitoring any laboratory. The agency will also recommend ways to protect against lead. This agency does the monitoring and provides an educational class on lead safety. This type of agency can be found in other states. Commercial consulting firms are also available, but they are expensive. Regardless of the technique used to determine lead concentrations, it is most likely that the average fire assay area exceeds the 50 µg/m3 (1.4 µg per cu ft) lead concentration limit. This is considered unsafe.

Jan 8, 1985

By Robert A. Jankowski, Jonathan Kelly, Edward F. Divers

Results for the first underground test of the ventilated drum in a U.S. coal mine are presented. Tests were conducted by the Bureau of Mines through a contract research program with Foster-Miller, Inc., to evaluate dust control effectiveness in a western mine and for gas control in a full scale laboratory facility. The ventilated drum is designed to reduce the amount of dust from cutting by drawing dust-laden air from the cutting zone through twelve water- powered "dust capture" tubes built into the shell of the shearer drum. High pressure water up to 1 12.48 kg per cm2 (1,600 psig), released from sprays, induces maximum airflow of 1.89 m3/sec (4,000 cfm) from the face side of the drum and provides cleaning for respirable dust and improved methane dispersion. At the gob side of the drum a deflector plate, attached to the cowl arm, turns the water spray and a proportion of the cleaned air back into the cutting zone. More than 50 ventilated drums have been installed to date in England, and their tests carried out on fixed height and single-ended ranging drum shearers have shown reductions in respirable dust of 60-80 pct, as compared with conventional wet cutting. The U.S. test on a double drum shearer showed slightly lower reduction.

Jan 1, 1987

By E. Sirolli

In recent times, with rare exceptions, most economically viable ore discoveries have been large, low-grade and located in remote parts of the world. Mining companies have often shown to be incapable of mitigating their social and economic impact on local communities. Sustainable development and relations can be achieved by implementing bottom-up methodologies to the top-down tools already in use by mining companies. In order to magnify the importance of enterprise facilitation as a primary method for community development, data from 25 years of community based work around the world was used. Results highlight the need for a grassroots approach to local economic and community development, which focuses on the creation of a parallel economy in communities. Using solely top-down methodologies for developing community relations is shown to be a limited resource for mining companies. There are fundamentally two dangers for mining companies: alienating the local population, resulting in militancy and lengthy legal battles to obtain a license to operate; and, being accountable for building social and economic infrastructure that are not the company?s responsibility.

Jan 1, 2012

By W. E. Horst

Historically, research organizations have made significant contributions to the development and commercialization of new chemical products for the mining industry and examples of commercial results are cited With the recent demise of research organizations within the mining industry and dynamic changes in the industry, the supporting role of R&D groups has become limited or non-existent. Cat- reduction requirements and new raw-material sources offer future opportunities for R&D organizations to continue their effective participation in the commerical development of new chemical products. Potential areas of interest for future process applications are reviewed.

Jan 1, 1986

By D. R. Willmer, E. J. Haas

"DISCLAIMER The findings and conclusions in this paper are those of the authors and do not necessarily represent the views of the National Institute for Occupational Safety and Health. Reference to specific brand names does not imply endorsement by the National Institute for Occupational Safety and Health. ABSTRACT This study analyzed the publicly available health and safety policies of 26 mining companies to determine the quantity of health and safety (H&S) practices that mining companies encourage in relation to the Plan-Do-Check-Act cycle. A thematic content analysis of the policies identified elements and practices within the text. On average, companies communicated information on about 7 elements (range 1–14, standard deviation = 3.49) and discussed 15 practices (range 2–34, standard deviation = 9.13). The elements in which companies highlighted the most practices were risk management, emergency management, leadership development, and occupational health. A discussion of the policy trends shows areas that mine sites can improve upon within their Plan-Do-Check-Act cycle, in addition to encouraging the use of both leading and lagging indicators to manage health and safety performance. INTRODUCTION Mining companies and their employees are expected to identify and manage risks at their worksites to ensure the health and safety (H&S) of everyone at the site. The primary mechanism in place to control these risks is a company’s health and safety management system (HSMS) (Boyle, 2012). Broadly, an HSMS is a set of standard, interrelated, and interacting elements used to promote and achieve occupational H&S goals (ANSI/AIHA Z-10, 2012; BS OHSAS 18001, 2007). The practices conveyed within an HSMS are expected to minimize incidents, injuries, illnesses, and even save worker lives (Alsop and LeCouteur, 1999; Arocena and Núñez, 2010). In the United States, both the Occupational Safety and Health Administration (OSHA) and Mine Safety and Health Administration (MSHA) regulate and encourage aspects of an HSMS (US Federal Register, 2011, 2010). Many HSMS documents (i.e., Chemical Industries Association, 1995; Health and Safety Executive [HSE], 1995; International Labour Office [ILO], 2001) attribute the source of their basic management system to Deming’s Plan-Do-Check-Act (PDCA) model of continuous quality improvement and organize their practices within this cycle (Johnson, 2002). The PDCA cycle is a well-adopted approach in health and safety management and promotes continuous learning and adaptability (Robson et al., 2007)."

Jan 1, 2018

By Rocky Gunderson

When operations begin early next year at the $100-million Port Kembla coal loading facility in New South Wales, Australia, a sophisticated computer system, directed by two of Hewlett-Packard's HP1000 mini-computers, will perform a number of functions ranging from monitoring and reporting arrivals and departures to maintaining a library of events for up to one year. The three-processor HP1000 system configuration, valued at $215,000, is one of the largest single orders, in terms of dollar value, ever submitted in Australia for Hewlett-Packard's line of engineering and manufacturing minicomputers. The processors will be linked in a fully "backed-up'' configuration using Hewlett-Packard's fourth generation distributed networking system, DS/1000-IV, making the system one of the most sophisticated in Australia. Interfaced to a number of weightometers and programmable logic controllers (PLCs), the computers will be the heart of a coal inventory system for the facility which, in its first phase, will be capable of handling more than 13.5 Mt/a of coal. The computers will report on all plant functions, including conveyor belt and water spray operations. Specifically, the system will: • Monitor and report all coal movements related to road and rail deliveries, dispatches from ship loaders, and interstockpile transfers. •Maintain a ''running log" of all events pertaining to overall plant operations, such as conveyor starts and stops and anti-pollution spray activation. • Accept and maintain plant data entered manually or acquired automatically from various remote locations via either visual display units (VDUs) or PLCs. • Maintain complete historical records of all transactions and related plant events for up to one year. • Provide a facility for stockpile management, modeling-type programs, and training or other simulation activity. The facility was designed with the following characteristics in mind, based on an analysis of requirements for an automated coal loading operation that would optimize productivity and be flexible to change and grow with facility needs and changing technology: • Continuous Operations-Due to the need for continuous plant logging and control, the overall facility will be capable of uninterrupted, 24¬hour operation. • Handling Current and Projected Workloads-The facility will be capable of not only handling current workloads, but also any additional workloads required during future coal loading operations. • Expansion-The facility will be capable of expansion, for a minimum cost, at any time with minimum disruption in operations. • Single Source of Supply and Maintenance-The facility will be supplied and maintained by one supplier, through hardware and software maintenance support contracts. System Configuration Two HP1000 minicomputers, each with 500K bytes of main memory, will be front-ended by a pre-processor with 256K bytes of main memory. These three systems, active, backup, and front-end, will be interconnected into a triangular array, as shown in the accompanying diagram. Under normal conditions, the front-end will transmit plant status data to one of the main systems, whose primary function will be to monitor coal flow and maintain a relevant dialogue with operators. The front-end, therefore, handles all communication with the plant PLCs, effectively removing this overhead from the current plant monitor (either of the two main systems). The front-end pre-processes and post-processes all information flowing from the plant monitor to the PLCs and vice versa, thus effectively handling all communication between the two units. A second main system will handle reporting, administrative, and modeling functions, and will also be capable of performing both front-end and monitoring operations. Linking all

Jan 11, 1981

By G. A. Perry

Cyprus Sierrita is a major producer of copper and molybdnum from its Sierrita and Twin Buttes open pit mines south of Tucson, Arizona. Both pits were started in the late 60's and are in excess of 1500 feet in depth. Sierrita has utilized a Cat 992C Remote Controlled Loader since January 1993. The loader was justified to increase SAFETY and PROFITS at Sierrita. It has exceeded all expectations. As of June 1993, it had produced additional profits totaling more than $1,500,000.

Jan 1, 1994

By H. R. Manouchehri

The responses of calcite, feldspar, and quartz minerals In a laboratory free fall electrostatic separator, before and after tribocharging with stainless steel, PVC, and copper plates, have been investigated. The effect of H3BO3 and BaCl2 chemicals pre-treatment on the electrical properties of the minerals is examined. The changes in the electrical properties are discussed with the determined charge, dielectric constant, and electrical conductivity of the mineral samples. Electrical properties of the minerals and their responses to the electrical field during separation, after tribocharging and chemical pre-treatment, are explored for the need to characterize the electrical behaviour of the minerals.

Jan 1, 1998

By Gregg Wilkerson

The Blind Springs Hill pumice beds are located 5 miles southwest of Benton, California in the foothills between the Benton Mountain Range and Blind Springs Valley. The best exposures of the pumice are in an area 0.75 miles west of Blind Springs Hill. The pumice is Quaternary ejecta material which came from the rhyolitic volcanoes in the Glass Mountain-Volcanic Tablelands area of Mono County. The pumice beds occur in two distinct layers separated by an unconformity. The upper layer is 0 to 11 feet thick and consists of coarse subangular pumice fragments, some of which are over 1.75 inches in diameter. The lower bed is medium to coarse grained with subangular fragments up to 1.0 inch. The lower bed is 0 to 9 feet thick. Overburden at the Blind Springs Hill deposit varies from 0 to 15 feet. There are approximately 1 million cubic yards of material in the deposit that can be mined. The size distribution in the deposit is mostly fine with only 10.6% of the pumice fragments being over 0.5 inch in diameter, the minimum size needed for stone-wash or acid-wash applications. Suitability of pumice for the textile industry is quantified by standard 15-minute abrasion and absorption tests. In the Blind Springs Hill deposit, the plus 0.5 inch fraction has an abrasion loss of 33% which is too high for stone-wash application but it has an absorption capacity of 36% which makes it suitable for acid-wash applications in the textile industry. The abrasion and absorption properties of this deposit are within the range of those which have been measured for other pumice deposits within the United States.

Jan 1, 1995

By G. K. Wilson

This paper will discuss some of the more important aspects to be considered when selecting pumps for mill discharge, cyclone feed or other severe-duty applications Included will be the selection of the pump based on such factors as particle size, particle distribution, head, flow, temperature and pH Other specifics to be covered: The relationship of impeller speed, head and wear factors as they affect pump performance and wear life; the importance of selecting a pump whose performance curve best suits the application; and how the addition of service factors applied to the actual operating conditions can lead to severe operational problems such as premature wear, pump running out on curve, and exceeding horse power limitations.

Jan 1, 1996

By J. Felipe Costa, Andrew H. White, Marcot T. M. B. Vilhena

Ordinary kriiing (OK) is an interpolation algorithm mostly used in earth sciences applications where it provides satisfactory results. Robust kriging (RK) is an alternative algorithm which at- tempts to minimise the problems caused by the existence of outlier values within a given data set. Robust kriging essentially consists of an editing step prior to running the traditional OK method. This study compares the interpolation results obtained by OK and RK. Two data sets were used. The first data set consists of 140 samples mimicking a drilling survey named cluster.dat. An additional feature of this sample data is that its parent population, the reference data set, is available, thus permitting direct quantitative assessment of the effectiveness of a given estimation technique. The second data set consists of a grid sampled at 1x1 m. The estimates obtained by OK and RK using cluster.dat were compared to the reference data set. RK provided better results in terms of quality of the estimates than OK

Jan 1, 1996

By Ian H. Clark

A series of numerical experiments were performed in order to elucidate the stress distribution, fracture strength and mineral liberation potential in single specimens of rock during crushing. Fracture strength was shown to reduce under eccentric loading conditions. Similarly, the presence of inclusions, both hard and soft, reduced the fracture strength. The predicted crack paths indicate that mineral liberation is unlikely to be preferential.

Jan 1, 1992

Power consumption of stirred media mills has been studied by an approach developed from work on stirred reactors. Relationships between torque required to rotate both disc and pin impellers immersed in dense particulate media as a function of speed, impeller and tank dimensions, and other relevant variables are evaluated. Data collected during numerous different experimental conditions are analyzed. The results can be summarized and presented in the form of characteristic plots, general equations and dimensionless group correlations involving power and modified Reynolds numbers. Special attention is directed towards the rheological properties of the media, which is considered as non-Newtonian liquids and hence, the equation of power law liquids is employed. Procedure for estimating parameters of effective viscosity and scale-up guidelines with respect to power consumption are put forward.

Jan 1, 1994

By Alfred Petrick, Roger Dewey

INTRODUCTION Estimation of capital and operating costs for mines and mills has long been a necessary ingredient of feasibility studies, and though many practitioners have successfully used "rules of thumb" and factor estimating methods for many years, a great deal of work is usually required to prepare an initial estimate and/or to update or revise such an estimate. Development of comprehensive mining and milling cost models during the 1970's by the U.S. Bureau of Mines and by Canadian workers (O'Hara and Mullar) provided the basis for feasibility-level cost estimates, but the numerous equations and the apparent rigor and complexity involved in preparing a project estimate using these models has discouraged many, if not most, potential users. Their acceptance was also hindered by a broad misunderstanding by many engineers in the minerals industries who had little exposure to such procedures, and by a possibly inadequate level of explanation or documentation of the parametric approach to cost estimating. The preliminary nature of most databases, geologic/engineering/ and market, available to the engineer or analyst during the early stages of a mineral project is a universal problem. Basing corporate mega-investment decisions or even individual equipment selection decisions on the usual "SWAG’s has always been a risky practice, but in the current business environment, the "guesstimates" are almost 'verboten', and are certainly becoming antiquated with the advent of both the described models, the ubiquitous microcomputer, and the nearly-ubiquitous hybrid species known as the "computerized engineer". Engineers have almost always sought techniques of cost estimation that can be applied and justified when geologic and engineering information for a mining project is preliminary and incomplete. The answer, in some cases, is the "parametric" approach. Equations, based on actual, past experience are developed to relate capital and operating costs to major physical variables such as the rate of mining or milling, with modifiers for such details as mining method, process characteristics, methods of construction, or types of equipment . Cost Engineering Standards Five major types of fixed capital cost estimates have been defined by the American Association of Cost Engineers : 1. Order-of-Magnitude estimate based on previous cost data and minimal knowledge. usually a "ratio estimate" with no better than +/- 30% accuracy. 2. Factored or ratio estimate based on major equipment costs with probable accuracy in the 25 to 30% range. 3. Budget authorization or Preliminary estimate, based on sufficient project data to

Jan 1, 1987

By M. Deutsch, E. González, M. Williams

"There is uncertainty in ultimate pit limits due to geologic variation and unpredictable economic landscapes. In this work we show how this uncertainty affects the ultimate pit and how it can be analyzed to improve the mine planning process. A stochastic framework using geostatistical simulation and parametric analysis is used to model the effects of geologic and economic variation on ultimate pit limits and overall project economics. This analysis is made possible by a new, highly efficient pit optimization implementation which can be automated and set up to calculate ultimate pits for hundreds of different scenarios in a matter of hours. Quantifying ultimate pit uncertainty early in the mine planning process allows mining engineers to make informed decisions regarding infrastructure placement, and to mitigate the possibility of incurring substantial costs relocating critical mine facilities. INTRODUCTION The mining industry is increasingly concerned with the effects of risk and uncertainty. Uncertain prices, unpredictable global markets, and unknown foreign exchange rates can alter the economic viability of a mining project in substantial ways. This economic uncertainty is compounded by geologic uncertainty. The extent and quality of any given deposit cannot be fully measured and is not known before consequential decisions must be made. These two sources of uncertainty are responsible for the majority of deviation between what happens during operation and what was initially planned. Understanding and explicitly quantifying this uncertainty will lead to better decision making and allow mining engineers and investors to be aware of what may occur. It is unrealistic to believe that one model, estimated from sparse measurements, is enough to capture both geologic and economic uncertainty and allow for optimal decisions. The entire breadth of uncertainty should be considered, as both upside and downside risks have large impacts on the investment potential and operational efficiency of mining projects. The workflow presented here uses Monte Carlo simulation and parametric analysis together to explicitly analyze the breadth of geologic and economic uncertainty as it applies to ultimate pit calculation and long range mine planning."

Jan 1, 2015

By J. S. Hu

FTIR spectroscopy has been used for the characterization of adsorbed oleate at the fluorite surface. It has been found that modest changes in the adsorption density at high temperature and high oxygen potential do not provide a satisfactory explanation for the significant increase in the hydrophobic character of the system under similar conditions. Rather, FTIR spectroscopic measurements suggest that chemical interaction between adsorbed oleyl groups occurs at high temperature and/or oxygen potential and accounts for the increased hydrophobicity. Specifically, the intensity of the =CH bond of the adsorbed oleate diminishes at high temperature and/or high oxygen potential. Such a phenomenon was not observed in control tests with the calcium oleate soap. For extensive reaction at the fluorite surface, the presence of a new surface species has been identified. These results indicate that the fluorite surface catalyzes an oxidation and/or polymerization reaction between adsorbed oleyl groups which results in a more hydrophobic structure at the fluorite surface.

Jan 1, 1986

By Harry D. Lewis

Gilsonite is a lustrous black material that can be easily crushed into a chocolate-colored powder. It is a solid but relatively soft, lightweight hydrocarbon that visually resembles the volcanic glass obsidian. It was once thought to be a type of coal, but because it is thermoplastic it melts rather than bums. Gilsonite is found in commercial quantities only in the Uinta Basin of eastern Utah and western Colorado, where it forms vertical, nearly parallel veins of varying depth, width, and length. Gilsonite from different veins has different properties, most notably variations in softening point and solubility. These differences result in its use in a variety of industrial applications. Gilsonite's earliest commercial uses were in varnishes, buggy paints, and beer vat linings. Eventually it came to be used in more than 160 products ranging from inks to explosives. It is exported from the United States to most industrialized countries throughout the world. Today, due to competition from synthetics and other hydrocarbon products, its use has narrowed to several specific industries. Although sold mostly as a commodity, current research is focused on applications for gilsonite as a value added product. Historical Overview The discovery of gold in California and the dawn of the mining era in Nevada, Colorado, and Utah around 1850 brought a wave of prospectors to the western United States. One of those pioneers, Samuel H. Gilson, is generally credited with a major role in the discovery of gilsonite. The material now known as gilsonite was discovered several times from the late 1860s through the mid-1880s. It was William P. Blake who, after receiving samples of the material, wrote a paper in 1885 describing "a new variety of asphaltum from the Uinta Mountains." He termed the material uintaite. Although Sam Gilson was not the first to discover the mineral, he was an-inventor who used gilsonite in products that he patented. It was his conviction that the substance was of great value, which caused some to refer to it as gilsonite. The term Gilsonite became the registered trademark of the American Gilsonite Co., and it continues to be in use today. When the first company was formed to mine this substance in 1886 it was named the Gilsonite Manufacturing Co. This firm acquired many gilsonite mining claims and marketed a varnish made from the material. It was the unusual properties of gilsonite varnish that attracted the attention of Adolphus Busch of the Anheuser-Busch Brewing Co. In 1889 Anheuser-Busch bought out Gilson's interests and formed the Gilson Asphaltum Co. Busch had been importing asphalt from Sicily for use in lining beer barrels and saw gilsonite as being more readily available and cheaper. Although gilsonite did not work well in this application, Busch did acquire a large number of mining claims in the Uinta Basin. In 1903 the parent firm of Gilson Asphaltum financed the building of an 85-km railroad from near Grand Junction, CO, to Dragon, UT, to haul gilsonite ore to market. Underground mining was initially centered near Dragon and then later at Bonanza, UT, as different veins were mined. The railway was abandoned in 1937 in favor of truck transportation. In 1938 Gilson Asphaltum changed its name to Barber Asphalt Co., the predecessor of Barber Oil Corp. In 1946 Barber Oil teamed with Standard Oil of California to form a partnership, American Gilsonite Co., which today has its operational headquarters at Bonanza, UT. Barber Oil investigated many new uses for gilsonite, including the making of petroleum derivatives such as gasoline. This work led to the construction of a 116-km pipeline to carry slurried gilsonite to a refinery in Colorado for the production of gasoline, fuel oil, and coke. Pipeline operations began in 1957 but stopped when the economics of competing with petroleum became unfavorable, and the refinery was sold in 1973. In 1981 Standard Oil (later Chevron) became the sole owner of American Gilsonite and remained so until 1991, when it sold its interest to Stratford Enterprises Co. of Tulsa, OK. The companies have since been merged and now operate under the name American Gilsonite Co. with headquarters in Salt Lake City, UT. American Gilsonite continues to be the world's largest miner and supplier of the mineral. The American Asphalt Association was formed in 1902 by former stockholders in Gilson Asphaltum. This company mined various gilsonite claims until it was dissolved in 1953 and its properties were sold to American Gilsonite and Gordon S. Ziegler and Associates. The Utah Gilsonite Co. was established in 1920 and mined several claims until 1952, when its holdings were sold to Gordon Ziegler. Several other gilsonite mining ventures have been pursued in Utah, although they were significantly smaller in scale than those described above. There are currently three companies which mine gilsonite resin in Utah. They are American Gilsonite Co., Ziegler Chemical & Mineral Corp., and Lexco.

Jan 1, 1994

By J. S. Stachulak

The Diesel Emissions Evaluation Program (DEEP), a research consortium formed in 1997 by Canadian mining companies, labour unions, and provincial and federal government departments, completed its work by mid-2006. This program, in which Vale Inco participated with both direct funding and in-kind contributions, investigated the ability of currently available technology to significantly reduce underground concentrations of diesel particulate matter (DPM) with high efficiency and low maintenance over a long-term period (years of life).While DEEP?s testing showed that engine maintenance is a critical component for lowering DPM, it was clear that reduction of DPM to the very low target levels of ~0.05 mg/m3 was not possible with maintenance alone. The best candidate technology for achieving low DPM levels was particulate filter systems. Furthermore, successful deployment of such systems was highly dependent on removing them from having to rely on human intervention for their regeneration. The search continues within Vale Inco to identify a reliable and rugged system.

Jan 1, 2009

By James Wm. White

Computer based dispatching in open pit truck haulage operations yields many benefits of current interest to mine management. The key tangible benefit is a substantial productivity increase with a given fleet of equipment or, alternately, a significant reduction in equipment required to meet production quotas. Other tangible benefits, depending on the operation, include minimizing rehandle, meeting several blending constraints simultaneously and ensuring a target plant feed rate. Intangible benefits include production forecasting, performance comparisons of trucks or shovels of different manufacture and extensive on-line report generation. Recent advances in mini and micro computer hardware and software and solid state electronics permit design and implementation of system features not feasible even a few years ago. Here we discuss many of these recent developments with emphasis on system aspects and dispatching algorithms.

Jan 1, 1983