Search Documents

By Matthew Anderson, David Day, Paul Smith

"The Midwest is presently the focus for Combined Sewer Overflow (CSO) abatement in the United States (U.S.). Most of the EPA mandated utility and municipal long term CSO abatement programs in large metro areas in the Midwest such as Cleveland, Indianapolis, Columbus, Chicago, St Louis, Akron, Fort Wayne, Louisville, Kansas City, Omaha and Pittsburg use or will use deep tunnels for storage and conveyance of CSOs. This paper will compare design methods specified and implemented for tunnel construction in Midwestern geology such as soft ground and mixed face EPBM tunnels, hard rock TBM tunnels, drill & blast tunnels, road header tunnels along with tunnel lining systems. It will also review the performance of successful CSO systems that include design life cycle, vortex and drop shaft configurations, pump stations, storage and conveyance strategies and long term operation and maintenance criteria. HISTORY and BACKGROUND Prior to development of mandated wastewater treatment plants, collecting both wastewater and storm water runoff in a single-pipe system was an efficient and economical solution. The early combined sewer systems were typically designed and sized to carry several times the average dry weather wastewater flows and not designed to handle a mixed volume of waste water and storm water during a wet weather event. Beginning in the early 1970s, federal legislation (Clean Water Act of 1972, Clean Water Act of 1977 and the Water Quality Act of 1982) changed how municipalities and industries in the U.S. were required to treat and discharge wastewater into the nation’s surface waters. They were mandated to treat wastewater at federal regulatory standards for discharge into surface waters that is safe for humans, wildlife and aquatic life. The wastewater treatment facilities that evolved were initially designed and sized to treat only the peak volume of raw wastewater flowing during dry weather. Combined sewer system control sections or relief structures were installed upstream of wastewater treatment plants (WWTP) and were designed to protect WWTPs from potential damage that would be caused if peak volumes of raw wastewater mixed with storm water runoff reached and overwhelmed the WWTPs."

Jan 1, 2016

By J. R. Henke

Dewatering wells producing iron-rich water experience rapid declines in yield and drawdown due to the formation of ferric (Fe +) hydroxide deposits in well screen, pump intake and riser pipe. Precipitation is caused by a combination of dewatering-promoted iron oxidation and iron-oxidizing bacteria. Physical and chemical well rehabilitation techniques, as well as alternative well construction and well development techniques designed to minimize well clogging, were evaluated in this study. The addition of acid downhole feed systems to dewatering wells prone to iron encrustation can, in some cases, prolong their operational lives up to 500 percent that of unacidified wells.

Jan 1, 1989

By M. F. Werneke

Flotation of the carbonate, oxide and silicate minerals of copper (malachite, azurite, chrysocolla) has been the subject of much research in recent years, but few effective solutions to this problem have been found. With decreasing reserves of sulfide minerals, the economic recovery of these "oxides" appears to be an important source of copper for the future. Xanthates have been known for many years to be malachite collectors (1), but only at very high dosages, or at lower dosages following activation of the mineral by sulfide ion. Dewitt and Batchelder (2, 3) found that chelating agents such as certain oximes were collectors for malachite and azurite, but also required high reagent dosages. Fuerstenau (4) has suggested, for example, that potassium octylhydroxamate may be an effective collector for malachite, On the other hand, Balberyszski (5) has found that oxide minerals may be completely sulfidized at high temperatures with gaseous sulfur or H2S, and then floated with conventional collectors. None of the above approaches appear to offer an economically effective method for the direct flotation of these oxide minerals.

Jan 1, 1977

By D. Carr, C. Anderson, M. Deal, C. Larson

"Construction of the OceanaGold Haile operation’s process plant in Kershaw, South Carolina is currently under way, with ore through the mill expected in late 2016 and commercial production expected in early 2017. The process is designed to treat 6,350 tonnes per day with minor upgrades required to achieve 8,270 tonnes per day. Plant optimization during detailed engineering, combined with a focus on de-risking the process, has resulted in numerous process changes since the initial design. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio operation, whilst identifying potential expansion opportunities. INTRODUCTION Haile Gold Mine is located in Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching from 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that delineated 2.02Moz. of gold in reserve at an overall grade of 2.06 g/t. OceanaGold acquired Romarco Minerals and the Haile Operation in October of 2015. OceanaGold operates under a risk management philosophy in all aspects of operation, both corporately and at each individual business unit, and has implemented numerous process changes to eliminate or mitigate risks identified in the initial design of the processing circuit, and provided increased opportunity for optimization and expansion. This paper describes the plant optimization and de-risking, it also presents a proven commissioning strategy modelled after OceanaGold’s Didipio Operation, and identifies potential expansion opportunities. INITIAL PROCESSING CIRCUIT DESIGN An extensive metallurgical test work program was undertaken by Romarco Minerals and third party laboratories during the initial design phase of the Haile project [1]. This preliminary test work provided the technical information as a basis of plant design. The initial flow sheet for the Haile processing circuit is shown in Figure 1 (see APPENDIX). The plant is designed to process 6,350 tpd (7,000 stpd) on an annualized basis. The process begins with a jaw crusher followed by a SAG and ball mill grinding circuit to reduce particle size to P80 74 µm. A flash flotation cell treats 50% of the cyclone underflow in the ball mill circuit. Grinding circuit product is sent to a rougher flotation circuit to recover gold-bearing pyrite. The flotation concentrates from flash and rougher flotation are reground to P80 13 µm using stirred media detritors (SMD’s). The rougher flotation tail is pumped to the carbon-in-leach (CIL) circuit for gold recovery. The reground concentrate is pre-aerated prior to being pumped to the CIL circuit. The CIL circuit is a hybrid circuit with eight tanks. Tank 1 leaches the pre-aerated concentrate only, and tanks 2 through 8 leach the combined flotation tailing and tank 1 discharge. The carbon strip circuit is a standard pressure Zadra system, followed by electrowinning, and refining using an induction furnace. CIL tailing passes through a cyanide recovery thickener prior cyanide destruction and then pumped to the tailing storage facility (TSF)."

Jan 1, 2017

By L. H. Pye

For large mining sites in the west, the traditional method for performing an ecological risk assessment (ERA) provides little useful information for risk managers faced with selecting and designing sound remedial options. Current U.S. Environmental Protection Agency (EPA) risk assessment guidance largely supports quantitative risk characterization of individual species as surrogates for population and ecosystem-level effects. Developing a work plan for investigating and remediating ecosystem-level changes potentially caused by large-scale historic mining/smelting contaminant release requires a decision process that incorporates a more holistic ecosystem management approach. Some of the most wasteful efforts associated with mine site ecological risk assessments arise when the risk analysis and data collection programs are not specifically linked up-front to the risk manager's decision needs. The following paper discusses the importance of employing a decision-based, ecosystem management framework when conducting ecological risk assessments at large mining sites. A case study of an ecological risk assessment currently being performed at a large New Mexico copper mine site is presented.

Jan 1, 1999

It has been reported previously that dolomite samples from different locations showed varying flocculation behavior with Poly(ethyleneoxide) (PEO). In this study it is determined that palygorskite associated with the Florida dolomite samples is responsible for their flocculation with PEO. A detailed characterization of the dolomite samples from different locations and its relevance to flocculation with PEO is discussed.

Jan 1, 1994

By John Marshall

Silverton was the queen city of the western mining towns in the early 1900s. Located high in the San Juan Mountains, the town constantly grew and changed. Yet, it was subject to the vagaries and whims of economics, politics and disasters, natural or otherwise. Breweries, smelters and sawmills serviced Silverton's swelling mining population, which reached several thousand at its peak. Two trains a day ran from Durango to Silverton, in addition to trains running from Silverton over the top of Red Mountain on to Ironton. They ran up Cement Creek to the little town of Gladstone and up the Animas River Valley to Howardsville, Eureka and Animas Forks. During these prosperous times, construction flourished. There were plenty of wooden structures, and many of these stand today. The first brick buildings were built by bricklayer Patrick Stanley in 1877. It took quite a while for the first car to arrive. Almost 28 years passed from the coming of the first train to the arrival of the first car. It was brought over 3,840-m (12,600-ft) Stony Pass from Creede, CO, in an incredible journey retold years later by Louis Wyman. "Dad's daydreams were not the idle musings or the fantasies of a mystic," Wyman said. "They had a way of erupting into reality. He advocated and built good roads," he said. "During the summer of 1910, he was up to his sweatband in a project that took in half the state of Colorado. He envisioned an automobile highway, unheard of at that time, running southwest from Denver through the scenic grandeur of the high Colorado Rockies. The road would traverse a thousand miles or more of the state's finest recreational land finally circling back to Denver. Years later, when all of the county roads had been connected, it became known as 'Colorado's Thousand-Mile Circle Route.' Of course, Silverton and the San Juans were bright stars along the way."

Jan 1, 1997

By E. W. Hawk

The power generation industry may be required to reduce CO, emissions if regulations related to global climate change are enacted. Coal-fired generation, which emits 82% of the power sector CO2, would be a likely target for CO2 reduction. Compliance with the Kyoto protocol will require a 30% reduction from the projected year 2012 emission level even with moderate load growth. This paper describes an analysis of power industry CO2 reduction options and their costs to assess how a generator would make compliance decisions under a mandatory CO2 emissions reduction program. Carbon sequestration, fuel switching and new plant construction are considered.

Jan 1, 1999

By Yongqin Zhang

A single bubble released into surfactant solution first accelerates, reaching a maximum velocity then decelerates to reach a terminal velocity. Modeling this "velocity profile" is fundamental to understanding the motion of bubbles in flotation systems. This contribution considers the terminal velocity. Modeling is by a combination of the Navier-Stokes equation for flow around the bubble and the Marangoni effect induced by surfactant on the bubble surface. Numerical simulation is shown to agree with experiment for bubbles in pure water and surfactant solutions.

Jan 1, 1999

Ferric (Fe3+) ions are omnipresent in flotation circuits. Depending on pH and the nature of the ore body, Fe3+ ions may play a role in the adsorption of thiol collectors on sulfide minerals. To investigate this possibility, a two-compartment galvanic coupling cell was designed. This cell was used to monitor changes in contact angle of a sulfide mineral in one compartment, while varying concentrations of the Fe3+ ions in the other. The results showed that Fe3+ ions promote xanthate adsorption as indicated by the increase in contact angle. Implications of this finding in sulfide mineral flotation in general will be discussed.

Jan 1, 1998

By Michael D. Sopko

This paper describes the project implementation from financing, through the engineering and construction phases, mine and process plant commissioning as well as operating experience realized to-date. The single line flowsheet used to process the lateritic nickel ore to a 75 percent nickel matte is presented with emphasis on the main pyrometallurgical operations. These include a rotary dryer, a unique reduction kiln, a 45 000 kVA electric furnace and two Pierce-Smith type converters. Associated infrastructure facilities and services necessary to sustain the 11 300 tonnes (12 500 short tons) per year nickel production rate are also described.

Jan 1, 1979

By K. Sasaki

Diffusion phenomena in mine airways are important to trace gas and dust introduced into mine ventilation flows. Authors have carried out tracer gas measurements to check mine ventilation using concentration-time curves measured in mine airways, however dispersion mechanism to enhance effective diffusion have not been cleared. A numerical model using discrete tracer points dosed into tube flow has been presented to simulate their movements in consideration of turbulent velocity profile and fluctuation. Numerical simulations have been carried out to predict distributions of dosed points in tube flows with turbulent velocity profile, turbulent intensity profile and Reynolds stress. The numerical simulation results show that a combination of turbulent velocity profile and fluctuation creates extremely large dispersion of points in longitudinal direction and concentration curve with long tail was observed. This dispersion by velocity profile and fluctuation contributes large effective diffusion coefficient compared with original diffusion coefficient dominating in uniform velocity fields. Furthermore, the effect of Reynolds stress on the concentration-time curves is discussed.

Jan 1, 2009

By H. V. Fairbanks

The following processes were investigated using ultrasonic treatment in mineral recovery: (1) cleaning coal from coal slurry ponds, and (2) extracting precious metals from tailings and other sources. The treatment entails the production of a water slurry of the material containing the mineral which is made to flow over the vibrating surface of the ultrasonic treatment unit. The vibrations transmitted into the slurry break up particle agglomerates and also produce a scrubbing action on the surfaces of the particles. The treated mineral particles were found to have increased settling rates, better compaction, and more rapid water drainage.

Jan 1, 1990

By J. Swensen, R. Brandon, A. Wallstein, S. Bessinger, J. Pile

It is generally agreed that C.C. White was the first to describe and market coal mine roof trusses beginning as early as 1967. White was issued a patent in 1969 1. Coal mine roof trusses were extensively used in the 1970’s, and their use has proven valuable in many difficult conditions. Beginning in the mid 1990’s, several types of bar/cable trusses have been introduced. A new and innovative bar/cable truss recently introduced offers several advantages. By eliminating many small parts, and simplifying the installation, these new trusses are much easier and faster to install, thereby increasing operator safety.

Jan 1, 2004

By Reece Kurre, Gabriel Walton

"Roof bolting has long been used in underground mines across the world to provide ground support. Modern roof bolts are cheap and easy to install with the use of specialized machines as a part of the production cycle. Lhoist North America’s Crab Orchard Mine is an underground room and pillar limestone mine that uses mechanically anchored roof bolts for ground support. The mine currently employs two different roof bolting patterns: a standard 5 × 5 foot pattern, and a 2.5 × 2.5 foot pattern for use in areas with particularly hazardous roof conditions. The purpose of this study is to evaluate the relative effectiveness of each bolting pattern.A series of numerical models were created using RocScience’s RS2. The models were based on a symmetrical section of the mine at its deepest point, and were modeled using Generalized Hoek-Brown failure criterion along with a discrete fracture network. A series of sensitivity analyses were performed on the models by varying parameters such as joint friction angle, crack persistence, joint randomization, and tensile strength of the limestone. Based on the results of the original models and sensitivity analyses, it appears that the standard bolting pattern provides sufficient roof support capacity under almost all the expected conditions at the mine, since factors of safety below the design value of 1.5 were only found for individual bolts in a few of the worst test cases considered. These results can help improve the Mine’s productivity and reduce operating costs without compromising safety.INTRODUCTION AND CASE STUDY DESCRIPTIONLhoist North America’s Crab Orchard Mine is an underground limestone mine located in Crab Orchard, Tennessee. The mine is located under an 800-foot-high mountain, and outcrops on three sides. The mine is accessed through three separate portals and has two main levels, along with a partially developed third level. Extraction is accomplished by the room and pillar method using 50 × 50 feet pillars and 50 × 50 feet rooms. The mining height is limited to 50 feet to keep the pillar width to height ratio around 1.0. Each heading is excavated in a two-stage process that consists of a 30-foot-tall top heading and a 20-foot-tall bench. A distance of at least 30 feet is maintained between the two levels at all times (Crab Orchard Mine Technical Staff, 2017)."

Jan 1, 2019

By S. L. Manske

The Mesquite gold deposit is a recent discovery of Gold Fields Mining Corporation lying 65 kilo- meters northeast of El Centro in Imperial County, California (Figure 1). The deposit is located on the southwestern flank of the Chocolate Mountains and is a bulk-minable, low grade "disseminated" orebody. Although the host rocks of the deposit are part of a regional high-grade metamorphic terrane, abundant brittle fractures, brecciation, and open-space vein fillings indicate that Mesquite mineralization is epithermal. Faulting which postdates the hydrothermal activity has complicated the original geometry of the orebody. Alluvium effectively hides most surface expression of the mineralization, but open-pit mining is now revealing the details of Mesquite geology.

Jan 1, 1987

Despite two large projects represented in the keynote docket, the mood of the 2011 SME Arizona Conference was summed up best by Ferol Baker, general manager of New Mexico Copper Corp. (a wholly owned subsidiary of Themac Resources Group), ?In the past, it seemed like you couldn?t go to a conference like this without hearing about one big new greenfield project after another. Now what you see is companies doing internal expansion or small-scale brownfield development.? Overall, the tone of this year?s meeting, held at the J.W. Marriott Resort at Starr Pass in Tucson, AZ, was upbeat, yet practical. From the keynote and luncheon addresses to the six panels of sessions, the projects described were positive about the future, yet focused on the details required to make those projects come to fruition.

Jan 1, 2012

By D. Pappas

Over the past decade, the number of contractors working in underground coal mines has nearly doubled; however, the effect this has had on the industry's injury rates has been the subject of much speculation. The confusion exists because the U.S. Mine Safety and Health Administration (MSHA) database does not assign contractor hours to the individual mining operations where they worked. To better understand the safety record of the contractor segment of the industry, the National Institute for Occupational Safety and Health (NIOSH) undertook a comprehensive analysis of the data contained in the MSHA database. The first part of the study compared overall contractor and operator trends from 1983 to 2009 related to employment, hours worked and injury rate. One unexpected finding was that the larger contractors tended to have higher injury rates than the smaller ones. The second part of the study directly addressed the role of contractors on the safety record of 10 large underground coal mines. A detailed analysis provided both injuries and estimated contractor hours worked at these mines for the period 1992-2007. Comparison between the estimated contractor injury rates and the reported operator injury rates at these mines indicated that the contractor injury rates were significantly higher at most of the operations studied. However, the industry-wide data indicates that contractor and operator injury rates have converged since 2005 and are now equivalent. Mining Engineering, 2011, Vol. 63, No. 11, pp. 73-79. Official publication of the Society for Mining, Metallurgy and Exploration, Inc.

Jan 1, 2011

By Paul T. Allsman, Paul F. Yopes

17.1--CURRENT AND FUTURE STATUS OF SURFACE MINING PAUL T. ALLSMAN AND PAUL F. YOPES 17.1.1--CURRENT The history of surface mining essentially is one of mining coal, copper, iron and aluminum ores, of placer mining gold and tin, and of pits and quarries producing clays, gypsum, phosphate rock, sand, gravel and stone. Table 17-1 is a summary of the estimated world and United States production of crude metallic and non¬metallic ores and coal in 1969. It includes estimates of the quantities produced by surface-mining methods. Two-thirds of the 10 billion tons are mined from the surface, ranging from a third of the coal. 57% of the metallic ores, and nearly all clays, stone, sand and gravel. Production by surface methods in the United States, parallels that of the world with one exception: about 90% of the copper and iron ore is mined from the surface, whereas elsewhere only about half the copper ore is surface mined. In Canada, surface mining of the Athabasca tar-sand deposits is a recent large-scale unique operation. In surface mining of coal and, to a lesser extent, metallic ores, much waste is stripped, but in nonmetallic pits and quarries the ratio between waste and ore usually is small. Assuming that the stripping ratio for surface mining in the

Jan 1, 1973

By C. L. Lin

The image-based On-line Particle Size Analyzer (OPSA) system has been developed at the University of Utah to measure particle size distributions under plant conditions where overlapped and segregated particles are being transported on a moving belt conveyor. Evaluation of the OPSA system at several plant sites has been completed. The results show a consistent agreement between the particle size distributions obtained from the OPSA system and those obtained from laboratory screen analysis of belt samples. These results and the stable performance of the OPSA system during the field tests suggest that continuous quality control of crushed products is possible using the OPSA system.

Jan 1, 1999