Search Documents

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By A. A. Mular

Examining a typical curriculum for mineral process engineers shows that traditional subjects remain important, namely, engineering, earth and basic sciences, mathematics and mineral proc¬essing technology. However, Table I shows additional subjects that may be woven into a modern curriculum, because of micro- and macro-engineering advances over the years. The ways to incorporate these subjects into the curriculum will vary from school to school. Such changes are in response to evolutionary technological and political needs as determined by society and business. Beginning with the 1950s, engineering empiricism was strengthened through micro-engineering, where fundamentals and mechanism serve as foundations. Scientific apparatus unique to the basic sciences (Zeta meter, FTIR spectroscope) was adapted to test new hypotheses. Coincidentally, as computers became more available, complex differential

Jan 1, 1992

By H. Mitri

A new monitoring device called SAFEBOLT (Stress And Force Evaluator in BOLTs) has been recently developed at McGill University. The device is essentially an alternative to the load cell, it permits the monitoring of bolt axial load in the field. The SAFEBOLT system consists of a portable readout unit, a connecting cable and the SAFEBOLT device, which is installed in the bolt head. The new device can be installed on any industry standard rockbolt or rebar. The device is completely encapsulated in the bolt head, which makes it resistant to corrosion, rugged, and free of any electric wires. Pilot tests at two underground Quebec mines were carried out and helped improve the initial design of the device head.

Jan 1, 2002

Two miners were fatally injured when a pillar bump occurred during retreat mining in a southern West Virginia coal mine. The mine was operating in the Eagle seam with overmining in the No. 2 Gas and Powellton seams. A coal bump is defined as a sudden and violent failure of coal caused by the release of stored strain energy in the pillar. While significant strides have been made by academia, industry, and regulatory agencies to better understand bump conditions and mitigation techniques, coal bumps represent a long standing, highly site-specific engineering problem in which the exact failure mechanism(s) is not clearly understood.

Jan 7, 2020

By R. H. Grau

The National Institute for Occupational Safety and Health's Pittsburgh Research Laboratory is now involved in research to identify silica dust generation in underground metal/nonmetal mines. The ultimate goal of this research is to develop control technologies to reduce worker exposure to respirable silica dust. Commodities and job classifications with the highest silica dust exposure have been identified through analysis of the Mine Safety and Health Administration's compliance dust-sampling database. Dust surveys were conducted in an underground limestone and gold mine to investigate silica dust sources, generation levels and the controls being used. A summary of the mining operations, sampling procedures, resulting data and suggested methods to improve dust control are provided.

Jan 1, 2003

By Ray E. Harris

All of the major raw materials (silica, soda ash, limestone, and feldspar) needed to manufacture most grades of glass are found in Wyoming. Additional advantages for the manufacture of glass include the state's geographic location, a well-developed transportation network, a favorable tax structure (no corporate or personal-income tax), and low energy costs. Inadequate local markets and prohibitive transportation costs to other markets have been the major obstacles to developing a glass industry in Wyoming, the least- populated state in the nation. The Rocky Mountain region only recently became a major market for glass, especially for the Colorado Front Range and Utah's Wasatch Front. Currently, changing costs of the production of glass, an increased market for con- tainer glass in the Colorado Front Range, and innovative production and transportation ideas (e.g., production of selected types of glass and bulk shipments of specification-glass pellets) favor developing a glass plant in Wyoming. Thus, the Wyoming State Geological Survey (WSGS) and other state agencies have been conducting studies and contacting investors in an effort to attract a glass-manufacturing plant to the state. Between 1987 and 1993, three locations of silica-sand and -rock deposits were studied in Wyoming (Cassa, Plumbago Creek, and John Blue). Funding was provided by the WSGS operating budget and local and state Department of Commerce economic- development grants. The reports on these areas were released between 1988 and 1993. In 1988-89, a California-based company conducted additional drilling and feasibility studies and prepared to construct a glass plant in Cheyenne, using the Cassa silica source. However, due to losses incurred by some of their other investments, the company did not proceed. In 1997, the Wyoming Science, Technology, and Energy Administration (STEA) contracted a market study for glass manufactured in Wyoming, using information provided by the WSGS. The STEA contacted several major glass producers, and a major glass-producing company began feasibility studies in January 1998, for the construction of a glass plant. In June 1998, bids to supply brown beer bottles to the Budweiser brewery northeast of Fort Collins, Colorado, were submitted by at least two companies that were considering glass-plant sites in Wyoming.

Jan 1, 1999

By P. O. Lindahl

The U.S. Bureau of Mines initiated research to improve the safety and efficiency of transporting coal from deep underground mines using a balanced air-lift hydrohoist. A 50-m-high pilot-scale model was constructed and tested to evaluate the feasibility of hydraulically hoisting a coal-water slurry in a U-tube pipeline from the mine level to the surface with the assistance of compressed air. A prototype screw feeder is used to continuously compact and inject 5-cm or less run-of-mine coal into a pressurized 20-cm-diam pipeline. Production rates up to 40 metric tph at an airflow of 1.5 m3/min were achieved with the model, and coal size degradation was relatively minor. Modifications are in progress to achieve 100 tph at an airflow of 2.8 standard m3/min injected into the riser pipe. Pilot-scale results indicate that an air-lift hydrohoist system is a feasible, cost-effective alternative to conventional skip hoisting that can be installed in existing shafts or surface-drilled holes closer to the face area. Air-lift hydrohoisting offers advantages of infinitely adjustable slurry flow rates, reduced pressure at the point of coal injection, and flexible design that can be combined with hydraulic pumping. Proposed design changes are discussed for coal transport, mine layouts, ventilation, fire control, and escapeways using this system.

Jan 1, 1995

By Jerry C. Tien

China?s remarkable levels of economic growth during the past three decades have lifted almost 300 million people out of poverty. This amazing achievement has placed an increasing demand on energy and minerals, especially coal, which supplies 68.7 percent of China?s energy (June 2011). It is estimated that China mined more than 3 Gt (3.3 billion st) of coal in 2010, three times as much when compared to merely 10 years earlier. Such an impressive achievement does not come without major costs ?? including concerns with mine safety and an increasing number of occupational illnesses due to fast growth. This article reports on one of the major safety concerns in China?s coal mining, dust and dust control practices, and known cases of caol worker?s pneumoconiosis affiliated with prolonged exposure to excessive coal dusts. The exact size of China?s mining industry is not known, but it is estimated the coal industry is at least five-million people strong, and the metal and nonmetals industry probably employs another three million people. To meet increasing energy demand, China mined more than 3.1 Gt (3.4 billion st) of coal in 2010 from its 15,000 plus coal operations1, most of which are small- to medium-sized operations with annual coal productions ranging from a few thousand tons to 300 kt (330,000 st). These small coal operations are typically in remote areas, inadequately engineered, poorly ventilated and still using rudimentary drilling and blasting mining methods employing antiquated mining equipment and, presenting safety concerns, i.e., methane and dust explosions.

Jan 1, 2011

By C. Laughton

Construction of a Deep Underground Science and Engineering Laboratory(DUSEL) is proposed under the auspices of the US National Science Foundation(NSF). DUSEL will provide scientists and engineers with a research facility capable of supporting a broad spectrum of fundamental and applied research deep in the earth’s crust. Research partners are physicists, biologists and geoscientists. DUSEL research calls for the construction of a network of shafts, tunnels and caverns that will provide laboratory facilities at depths of up to approximately 2 kilometers. The Project is still in the planning stages but, the initial experimental program is taking shape and conceptual designs have already been developed at two hard rock mine sites. This paper discusses the overall program and key engineering tasks being developed to support the construction of deep, large-span caverns. These caverns will house a new generation of physics experiments. As currently scoped, the experiments call for the excavation of permanent caverns with spans of up to 60 meters, sited at depths in excess of a kilometer.

Jan 1, 2007

By R. Xiong, A. K. Fallaw, G. Wang, L. R. Moore, S. Dobson, J. Gu

"INTRODUCTION The Central District of the Florida phosphate industry is located in southwest Polk and southeast Hillsborough Counties, with the Southern Extension lying in western Hardee, eastern Manatee and northwest De Soto Counties. (Lawver, 1983) Figure 1 shows the major phosphate formations in Florida. Almost all Florida phosphate production has been in the Central district with additional production from a mine in the Northern District. The Central District is comprised of the Bone Valley Deposit, a relatively thin layer of high grade ore which has been the main source of phosphate mining for decades, and the Hawthorn formation, a thick but low grade formation which covers most of peninsular Florida. (Lawver, 1983) Florida phosphate producers use the Crago process where calcium phosphate is floated with anionic, fatty acid type collectors followed by cationic reverse flotation of silica with amine type collectors. The phosphate matrix is put through various size separation techniques to obtain a typical -28 Mesh (< 700 µm) particle size for fine flotation and a -16 mesh (< 1190 µm) to +28 mesh (> 700 µm) particle size for coarse flotation. In some cases this coarse fraction can be sent to shipping as an intermediate product. The +16 mesh (>1190 µm) to – ¾“ (19 mm) fraction is sent to shipping as a final product called pebble. Figure 2 demonstrates a simplified diagram of the mining and processing of calcium phosphate (matrix) through a Central Florida mine. Particle size and mineralogy are important considerations in the Crago process for two main reasons, the mass of the particle and the particle surface area. Both of which are dependent on the coordination of the anionic collector to available Ca2+ sites on the minerals’ surface. The increased surface area, and available Ca2+, of the smaller apatite particles will allow for more fatty acid molecules to coordinate than the larger particles, with a lower availability of Ca2+. So, the larger particle would require more collector to be introduced in the system to sufficiently cover the apatite particles to produce a surface sufficiently hydrophobic to attach to air bubbles allowing flotation to occur. (Guan, 2009) The Bone Valley deposit has very favorable flotation characteristics when compared to other mining ores around the world. The matrix of the Bone Valley is relatively high grade, BPL (Bone Phosphate in Lime) values typically range from 6-18%, BPL recoveries, from such a matrix, can often be achieved above 85+% with fatty acid based collectors dosed below 1 #/ton. As mentioned, the sizing is an important step as there is also high grade apatite in the +16 mesh (1mm) that is screened to a final product grade, 60-65% BPL. The lack of quartz in the larger size fraction has allowed the Central District to produce high quality, low cost phosphate product, called pebble, through effective screening with no further beneficiation. (Guan, 2009)"

Jan 1, 2015

By R. Q. Honaker, D. P. Patil, A. Sirkeci

Due to increased production of fine coal during mining during this century and inefficient fine coal recovery technologies, a vast reserve of high quality coal currently exists in refuse ponds. A novel fine coal circuit consisting of a hindered-bed classifier, an enhanced gravity concentrator and a flotation column has been evaluated for the recovery of fine coal from refuse ponds. The treatment of a pond derived from Pittsburgh No. 8 seam coal resulted in the production of a premium fuel containing less than 5% ash and a calorific value of about 30,173kJ/kg with 60% mass yield. The results from the treatment of two refuse pond materials will be presented in this publication.

Jan 1, 2000

By B. Berhe, R. D. Lawrence, J. Hinzer

"The fortunes of mining companies and their implied value are tied to cycles - both economic and commodity – within which they operate. Hence the determination of appropriate future metal prices is one of the most critical factors faced by mineral valuators especially for advanced projects. Price, and hence revenue, is usually the most sensitive input to the valuation model. Empirical studies of past forecasts show that the success rate for commodity price forecasting is very poor. This paper explores various approaches and comments on their strengths and weaknesses. We conclude that careful evaluation of long-term metal prices is a key element and is hardly a luxury that can be left to simple averages or rules of thumb. INTRODUCTION Discounted Cash Flow (""DCF"") analysis, is well suited for the valuation of advanced mineral development assets, for which there are identified mineral resources and some form of economic assessment (Pre-Feasibility or Feasibility Study). The DCF method is also the most commonly used method for determining value for such assets. It provides a means of relating the magnitude of expected future cash flows from profits (or losses) to the magnitude of the initial cash flow (investment) needed for capital expenditures to purchase or to develop an asset for commercial production. The method proves useful in making investment decisions as it allows for the quantification of the Net Present Value (“NPV”), as well as the Internal Rate of Return (IRR) and Payback Period on initial investment capital. Valuation by its very nature is a forward-looking exercise. The DCF method attempts to estimate the NPV of expected future cash flows, by selecting factors that will likely affect future cash flow based on informed analysis. One of the most critical and sensitive factors is the determination of appropriate future commodity prices. “The variables that have the greatest impact on a DCF evaluation are the reserves, the metal prices, and the discount rate.”1 The determination of future commodity prices for valuation purpose or during M&A negotiations is a hotly contested issue. There are a number of analysts, institutions and specialized commercial data suppliers that provide both short and long-term commodities price forecasts. Also, the use of an aggregated mean for all available forecasts, or consensus forecasted prices for valuation purposes is not uncommon. The methods used in making forecasts for each forecaster may vary and in many cases may not be publically disclosed. Nonetheless, the aggregated mean of all forecasted commodity prices of reputed institutions is usually taken to “represent the market’s view of likely future commodity prices.”"

Jan 1, 2016

By Z. T. Bieniawski

Ground support requirements for safe and economical design of room and pillar coal mining layouts are reviewed. The design methods for mine roofs and mine pillars are discussed and the role of the geotechnical aspects is considered. It is shown that current support design procedures in the United States do not utilize fully the latest research findings and the need for more effective technology transfer in coal mine ground control is emphasized. Promising new developments in ground support are identified and possible research areas are suggested.

Jan 1, 1982

By W. de Bruijn

Differential reduction and expansion or shrinkage of hematite under the influence of intimately associated foreign oxides may be a source of stress formation and sinter degradation during blast furnace reduction. To study specific effects, synthetically pre-pared hematite powder evenly doped with 1% by weight of several elements present as oxides, was pressed into tablets and sintered at high temperature prior to reduction. Continuous thermo-gravimetric and dilatometric analyses were per-formed on the sintered tablets as these were being subjected to reduction under simulated blast furnace time/temperature/gas composition conditions up to 1183 K. These findings were coupled with observations on the microstructure of tablets removed from various stages of the reduction process.

Jan 1, 1988

By M. Javier

This concept paper is presented in the hope of raising the awareness of mankind on the necessity for its peaceful coexistence with nature. It is a food for thought. It takes compromise and sacrifice of people, who will have to learn to curb their greed and move toward a more organic form of prosperity. A nature-friendly sustainability is first step toward the protection of nature that is critical to the mutual survival of mankind and nature. People need the resources from the finite earth to survive and nature needs the prevention of human destruction in order to continue to regenerate and provide. The contemporary notion of sustainability is self-serving. It serves the interest of industry by camouflaging itself to look like nature?s protector. The ?sustainability? concept presented in this paper aims to extend the longevity of the utilization of the limited natural resources for many generations to come. It is an important, responsible first step in creating a healthy sustainability concept that, when implemented, extends the longevity of mankind by the most efficient use of the finite resources on this limited Planet Earth, all the while taking into consideration the increase in anthropogenic activities due to exponential human population growth. This new definition of ?sustainability? has completely different characteristics than its contemporary versions. Nature has its own destiny, rules and principles. Being a part of nature, human society depends on it for survival and must play by its rules and never the other way round as in its initial pretensions. Society should not try to humanize nature, but rather to respect the rule of the nature in a peaceful way of co-existence. When implemented, this new concept of sustainability aims to affect the designs of engineered structures and revolutionize the recovery methods and processing of natural resources, such as mineral resources in the most efficient manner. Finally, this paper intends to stimulate critical thinking and initiate serious discussions aiming at producing a general consensus for the best definition for human society to not only enrich, but to extend its existence. Thus, the spirit of this new definition is pro future generations and environment. KEYWORDS: Sustainability Definition, Nature, Geomímic, Deproduction.

Feb 27, 2013

By James P. Rider, Robert P. Vinson, Fred N. Kissell, Jon C. Volkwein, Gregory J. Chekan, Jay F. Colinet

The Thermo-MIE personal DataRAM dust monitor (pDR) is a light-scattering instrument approved for use in gassy underground mines by the U.S. Mine Safety and Health Administration (MSHA). However, the use of lightscattering monitors has been inhibited by concerns about inaccurate readings resulting from changes in dust size distribution and composition, as well as concerns about the impact of moisture in the mine air. Because of this concern, the National Institute for Occupational Safety and Health (NIOSH) has evaluated the pDR using available data from laboratory tests and mine surveys. The data show that accuracy can vary widely from test to test and mine to mine. In most cases, the results can be improved by using a companion gravimetric measurement to adjust the pDR data.

Jan 1, 2005

By P. T. Bissert, L. Yan, M. D. Klein

"Since 2008, the U.S. Mine Safety and Health Administration (MSHA) has required the installation of refuge alternatives (RAs) in underground coal mines (MSHA, 2008). MSHA requires that RAs provide an environment with breathable air for entrapped miners for a 96-hour period. Heat buildup inside an occupied RA is a serious concern. Without a means to dissipate the heat and humidity generated by the occupants and the carbon dioxide scrubbing system, the temperature and humidity inside RAs could lead to severe discomfort or heat stress depending on the mine ambient temperature before and during occupation of the RA. In its 2006 report, the West Virginia Mine Safety Technology Task Force (2006) recommended an apparent temperature limit of 35 °C (95 °F) for RAs. In Title 30 Code of Federal Regulations Part 7.504, or 30 CFR 7.504, MSHA specifies a maximum apparent temperature of 35 °C (95 °F) inside an occupied RA (MSHA, 2016). The apparent temperature is calculated using both air temperature and relative humidity (Steadman, 1979).Calculations can be used to deter-mine if the air within an occupied RA will reach the apparent temperature limit. In these calculations, the mine temperature could be assumed to re-main constant. With this assumption, the effects of the mine strata thermal mass and thermal conductivity on the heat buildup in an RA are ignored. Re-search conducted by the U.S. National Institute for Occupational Safety and Health (NIOSH) shows that the mine air and strata temperatures surrounding an RA increase when subjected to the heat of an occupied RA (Yantek, 2014). Thus, calculations performed with the assumption that the mine temperature is constant would underpredict the resulting dry-bulb temperature and apparent temperature for a given RA occupancy. The mine air temperature has been used as the basis for RA temperature calculations. However, there has been no research to confirm that the mine air temperature is the appropriate basis."

Apr 1, 2017

By Dell H. Adams

Coal exploration may be defined as the acquisition of data necessary to define and acquire a block of coal which can be mined at a profit. Unlike ore minerals, coal resources are widespread and relatively abundant with supply exceeding demand in almost every case. Thus simple discovery of coal is generally not enough. The chemical and physical variability of individual coal seams, the capital intensive nature of coal mine development, and the changing patterns of utilization require that a multiphase, three-dimensional evaluation be made of each potential reserve. Factors which must be investigated include not only the quantity and quality of the coal but also the geologic, hydrologic, and engineering characteristics of the seam and its surrounding strata. Acquisition of property to provide a secure base for exploration and mine development is equal in importance to the geologic and engineering programs. The successful development of a coal reserve requires that control of coal and, in the case of a strip mine, the surface be in the form of contiguous blocks of sufficient size to support mining.

Jan 1, 1981

By Lars Johansson

The LKAB group consists of eight producing and trading divisions and subsidiaries, plus six specialist and staff organizations. It employs over 8.000 people and has a turnover of $ 500 million. LKAB produces over 30 million tonnes of ore products per year at its own mines and processing plants, making it one of the world&apos;s biggest iron ore exporters. This yearly production includes 15 million tonnes of lamp ore, 3 million tonnes of concentrate, and 8 million tonnes of pellets. The ore products are shipped via the company&apos;s own ore harbours, principally to iron and steel works in continental Europe. [ ]

Jan 1, 1979

By J. E. Friant

The Mini-DiscTM cutter drill bit is a radical design departure from the traditional tri-cone rockdrill bit. Miniature disc type cutting tools as small as 3.25 inches (82.5 mm) diameter are fitted to a bit body to cut individual concentric kerfs. The action is the same as that commonly used on large tunnel boring machines but miniaturized. The high performance rate and efficiency of a disc cutter are the result of producing a large proportion rock chips rather than sand or powder. The Mini-DiscTM drill bit, referred to as the “Disc Bit” has other unique features as well. It can be re-greased between runs. It can be rebuilt in the field in about 15 minutes, cutters can be replaced and the Disc-Bit appears to require less down hole hydraulic power than conventional bits. Thoroughly tested in the laboratory, the bit has recently been undergoing field trials in well drilling, blast hole drilling and shaft drilling. As any engineer knows, the laboratory can not shake out all the problems but it eliminates the more glaring weaknesses. Performance results have been exhilarating, and a few mechanical problems were discovered and largely overcome. This paper is a progress report.

Jan 1, 1999