Search Documents

By Diler Katircioglu-Bayel

This study aims to investigate the effect of combined mechanical and ultrasonic milling on the size reduction of talc. Firstly, the talc sample was wet ground in a stirred media mill for five different times (30, 60, 90, 120, and 150 min), and the optimum result was subsequently achieved with treatment by ultrasonication. The effects of amplitude (20, 35, and 50 μm), solid content (2.5, 5, 7.5, and 10%), and sonication time (60, 120, and 240 min) on the sizes of the final product were investigated. The pre-milling by wet grinding caused a decrease in the grinding resistance of talc. Sequential ultrasonic treatment, which was applied to the talc sample, generated smaller particles in comparison to those acquired by stirred media milling alone. Experimental results were assessed based on the product particle size (d10, d50), reduction ratio, and specific energy consumption. Submicron particles prepared by ultrasonic treatment were perfectly stable compared to stirred media milling alone as investigated in terms of particle size. In addition, the effects of mechanical and ultrasonic milling on structural properties of talc particles were characterized by XRD analysis.

By Janusz S. Laskowski

Studies carried out over the last 10 years reveal that precipitating particles which may appear in alkaline solutions of long-chain amines and in acidic solutions of fatty acids exhibit clear isoelectric points around pH 10.6-1 1 for dodecylamine and around pH 2.5-3 for fatty acids. These colloidal species can accumulate at solid/liquid and liquid/gas interfaces and affect flotation. While the precipitate in solutions of fatty acids apparently can chemically interact with the mineral surfaces and is flotation-active if sufficiently long conditioning time is available, the cationic flotation of quartz in alkaline solutions is depressed by the colloidal precipitate. The experimental data available in literature on the adsorption, electrokinetic, contact angle and surface forces measurements in the solutions of the weak electrolyte collectors are analyzed and the role played by the precipitate is discussed. It is shown that these concepts allow for an explanation of the selective flotation of sylvite from halite with long-chain amines in potash ore flotation.

Jan 1, 1999

By F. M. Benavides

This paper presents recent developments in federal environmental regulations, which in the view of the author, affect mining and the mineral processing industries. This is a summary of activities by the administration, congress and regulatory agencies during 1990. The information presented is a recap from material published. The emphasis is given to Air Quality regulations, although other environmental concerns are reviewed.

Jan 1, 1991

By T. Cienski

The paper presents and discusses the results of a detailed study conducted on the subject of energy consumption in the comminution of industrial minerals. The study was based on pilot circuit testing, plant operating data collection, detailed equipment data and literature research. The areas covered by investigations include: high efficiency classification; air classifiers for cement grinding circuits; grinding aids in dry grinding: dry grinding circuit, control based on particle size measurement. Results obtained indicate a large potential for the reduction of energy consumption, in particular in the traditionally high cement clinker grinding circuits. Better classification techniques and correct application of grinding additives can significantly reduce power used per ton of product and also substantially increase grinding circuit output.

Jan 1, 1990

By A. R. Laplante

A novel methodology to estimate gold recovery by gravity is presented. The methodology makes use of a population balance model which represents gold liberation, breakage and classification behaviour and applies pre-concentration and recovery performance curves to gravity-recoverable gold to predict overall recovery. Derivation of the necessary parameters is explained and demonstrated using data from an actual gravity circuit and one projected application. The methodology makes it possible to estimate the performance of circuits with large gold circulating loads and relatively low unit recoveries (e.g. jigs), or with high recoveries on a bleed of the circulating load (e.g. Knelson concentrators).

Jan 1, 1994

By Zhigao Xu, Ming Wu, Jun Qu, Rong Zhang, Wenrui Nie, Ruan Chi, Zhenyue Zhang, Zhengyan He

The leaching processes and mechanisms of weathered crust elution-deposited rare earth (RE) ores with ammonium sulfate were investigated for their high efficiency and low consumption exploitation. The leaching process is a typical reversible heterogeneous ion exchange reaction in liquid–solid systems. The raw ore and leached tailings were analyzed by SEM and FTIR. Results indicated that no dissolution or structural changes of the ores occurred during the leaching process. The migrations of RE3+, Al3+, and NHþ 4 in the leaching process were studied under various liquid–solid ratios. With increasing liquid–solid ratio, the content of NHþ 4 adsorbed on clay mineral by physical effect decreased, NHþ 4 adsorbed by ion-exchange increased, and the content of exchanged RE and Al increased until reaching equilibrium. The adsorption capacity of the RE ores for NHþ 4 remained about 0.61–0.63 mg/g. It was difficult to desorb NHþ 4 from RE ores with washing water alone. The leaching mechanism of Al was the same as RE, but the leaching of Al slightly lagged behind RE. At the optimal liquid–solid ratio of 0.4:1, the leaching efficiencies of RE and Al were 95.51% and 90.99%, respectively, and 56.65% of NHþ 4 remained in the leachate. After impurity removal and RE precipitation, the leachate can be reused by replenishing fresh leaching agent. The aim of this study is to enhance the leaching process of RE, restrain the leaching of impurities, and decrease the consumption of leaching agents.

By J. Hebert, J. Donnelli, J. Sedey

Installation of a Load Commutated Inverter (LCI) provides an economical method for conversion of a Fixed Speed Semi-Autogenous Grinding Mill into one with variable speed, qualities. Though capital intensive, the conversion appears to be one of the most cost-effective methods to gain the advantage of critical speed variations for variable ore characteristics. Expected advantages from the installation of LCI drives at the Goldstrike Mine were decreased liner wear, decreased media consumption and additional grind for increased production rates. These issues as well as construction, economics and performance will be discussed in the presentation. The utilization of the existing equipment came to play an integral part of the study and economic justification of the overall project.

Jan 1, 1999

By G. Gregory Bryan

G. GREGORY BRYAN 33.1-DEFINITIONS 1. Engineering-Engineering may be defined simply as the science and art of making materials and energy serve the purposes of mankind. There are many fields of engineering, each with specialized branches. The basic fields are: civil, mechanical, electrical and chemical. Others may be specialized phases of one of these or a combination of two or more of them. Mining engineering, for example, requires a working knowledge of construction, mechanics, electricity, metallurgy, geology, accounting and economics, in addition to mining techniques or methods. Mining geology and geological engineering involve rocks and their structure and the forces that act upon them, and chemistry, physics and mechanics also are important to practitioners in these fields. Metallurgical engineering requires chemistry and physics but also a working knowledge of mechanics and electricity. The fields of engineering with which this section are concerned are those primarily involved in the finding, mining, processing and utilization of the natural mineral resources of the earth. They include geology, mining engineering and metallurgy, each with several specialized subdivisions. 2. The Engineer-The engineer is an individual who has had specialized training to qualify him to practice the profession of engineering. The term engineer is used here in its broadest sense to include such professions as certain applied branches of geology, physics and chemistry, whose practitioners may not have acquired engineering degrees but who, nevertheless, by training and experience in some area of the minerals industry, qualify under the above definition. To become a successful engineer, a person should have certain pronounced aptitudes and preferences, even before embarking upon the requisite course of training. Among the chief qualifications that the engineer-to-he must possess are: (a) a natural inclination toward mathematics and the physical sciences, and (b) intellectual and moral honesty. Among the qualities the student engineer must develop are: (a) independence of thought, open-mindedness, sound judgment and the ability to observe, deduce, plan and apply solutions, (b) the ability to articulate and convince, and (c) the ability to organize and direct the activity of others. These qualities are normally developed through sound education, followed by pro¬gressive experience. 3. The Consulting Engineer-The consulting engineer is an engineer primarily in the business of furnishing specialized advice and engineering services on an intermit¬tent, part-time or occasional basis to clients who do not have continuous or full-time need for those services. He must be able to make and take full responsibility for decisions and recom¬mendations where original thought is required. He should not be confused with the engineer, surveyor or technician who also may furnish services on an intermittent basis, such as regular periodic surveys, the overseeing of drilling programs and other such routine work as may require little original thought and planning. 33.2-THE PROFESSION OF CONSULTING ENGINEERING 33.2.1- QUALITIES REQUIRED A successful consulting engineer must first have, as a minimum, the qualities and preparation of an engineer. In addition, he must have sufficient knowledge,

Jan 1, 1973

By Gordon M. Elliott

Health risk underlies all of today's environmental regulations. Mine Manager's are no strangers to risk, but risk in the context of mine management is not the same as risk in the context of environmental regulation. One of the risks facing the mine manager is whether the mining operations meet environmental compliance standards. These standards are defined in terms of the frequency of occurrence of adverse health effects in an exposed population (i.e., health risk). Demonstration of compliance necessarily involves mathematical modelling and selection of values for input variables. What is not immediately apparent is that the method of estimating the human health risk has a significant influence on remedy selection and the amount of money spent at suspected contaminated sites. Using a hypothetical, mining-related example, this paper illustrates the disassociation between the current deterministic approach to health risk assessment and cost-effective decision making. This paper also illustrates how the probabilistic approach to health risk assessment provides a more realistic characterization of health risk and enables mine managers to identify cost-effective remedial strategies for the site.

Jan 1, 1992

By Geo. A. Wells

Abstract The consumption of barytes in certain paints polyurethane foams, seamless, flooring, glass, brake linings, plastisol caskets for food containers and in fluids used for gastrointestinal X-ray examinations rely on tie unique properties of barium sulfate, There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase prices which have encouraged the use of alternates and restricted market growth.

Jan 1, 1980

By Craig Cina

Transporting goods from producers to consumers is a fundamental part of the US economy. The demand for transportation closely reflects the economic health and well-being of the nation's industrial, commercial, and agricultural sectors. The inland waterway barge industry has traditionally played a key role in transporting needed commodities to industries on an economical basis. Barges account for 10% of the domestic intercity tonnage carried by all transportation modes. Water carriers operating on inland waterways hauled more than 450 Mt (500 million st) of cargo in 1980-up from 428 Mt (472 million st) in 1970. Inland Waterway Shipments Metallic and nonmetallic minerals comprise one of the largest commodity groups moved on inland waterways. As illustrated in Table 1, metallic and nonmetallic mineral shipments accounted for more than 69 Mt (77 million st), or nearly 15% of all commodities shipped in 1980. Putting this tonnage in perspective, coal and petroleum represent the two largest commodities moved on inland waterways. In 1980, petroleum and petroleum products accounted for 138 Mt (152 million st), or 28% of all commodities shipped. Similarly, coal represented 120 Mt (132 million st), or 25% or all commodities shipped. Even though shipments of metallic and nonmetallic minerals are smaller than coal and petroleum, they still account for a sizeable portion transported. The inland barge industry moves a variety of metallic and nonmetallic minerals ranging from manganese ores to building cement. Minerals transported by barge include: • iron, copper, bauxite, and manganese ores for metal production; • lime and limestone for construction and electric utility scrubbers; • phosphate rock, natural fertilizers, and gypsum for agricultural needs; • sand, gravel and crushed rock, clay, asphalt, tar, and pitches, and building cement for construction purposes; and • a host of other minerals to meet industrial needs. A few mineral commodities are responsible for a large proportion of waterborne mineral shipments.

Jan 10, 1982

By Ronald J. Doll

The selection and matching of the conveyor drive components (Figure 1) determine the initial cost, long term costs, and how well the drive performance is matched to a project's long term production goals. This paper will cover the specification criteria and considerations that should be included in a conveyor drive specification. It will also review the practical aspects of the specification's intent and the solicitation of alternatives.

Jan 1, 1998

By K. Perry, B. Lusk, Q. Huang, R. Honaker

"Rock dust is applied in underground coal mines to prevent the propagation of coal dust explosions. The application is conducted either dry or wet. Both methods have advantages and disadvantages however the formation of caked rock dust particles is cited as a significant concern for wet applications. A study was conducted to evaluate the effect of modifying the rock dust particle surfaces to repel water and each other by the addition of oleic acid (OA) and sodium oleate (NaOL). At a NaOL dosage of 2 lbs/ton, a contact angle of 112o was measured indicating strong surface hydrophobicity and ability to repel water. FTIR studies indicated a chemisorption mechanism which is necessary for long term stability of the surface modification. The dispersion rate of the modified rock dust samples was elevated by the application of both OA and NaOL thereby indicating a significant reduction or elimination of the detrimental effect of caking. Tests in an explosion chamber showed a 79% reduction in the dust explosion potential relative to untreated rock test applied by the wet technique. INTRODUCTION Mine explosions have been a long-time threat to underground coal miners attracting significant attention to the accumulations of combustible dusts and gasses. In the presence of sufficient oxygen and heat, the accumulations of combustible dust and gass can lead to large-scale underground coal mine explosions [Harris et al., 2010]. To alleviate the problem, rock dust such as limestone can serve both as a thermal inhibitor and a heat sink to inert the coal dust explosibility thereby prohibiting the occurrence of dust explosions [Richmond et al., 1975; Amyotte et al., 1995; Dastidar et al., 1997; Man et al., 2009]. The dispersibility of the rock dust is an important characteristic that determines the degree of explosion prevention [Greenwald et al., 1938; Mozumdar et al., 1974; Amyotte et al., 1995]. Unfortunately, the environmental conditions of an underground mine has the potential to cause caking of the rock dust which reduces the dispersive characteristics needed. The dispersive property of rock dust can be enhanced by modification of the particle surface properties by the application of chemical additives [Greenwald et al., 1938; Mozumdar et al., 1974; Spence, 2004; Vogt, 2011; Doidge et al. 2014]. The major mechanism for rock dust caking is the adsorption of water which forms liquid bridges at the particle-particle contact points where saturated solutions of soluble powder ingredients are present. Changes in temperature or relative humidity result in solvent (water) evaporation and the formation of dry bridges [Rumpf, 1958; Specht, 2006]. One method to prevent caking is creating hydrophobic rock dust to repel water from the solid surface thereby preventing the formation of liquid and solid bridges."

Jan 1, 2015

By Werner A. Ruemmele

Eisenhower Memorial Tunnel, called Straight Creek Tunnel during construction is located 60 miles west of Denver, Colorado at 11, 160 ft. elevation. It is 8, 510 feet long, and carries two lanes of 1-70 traffic under the Continental Divide. This paper describes improvements and changes made in construction methods for utilities, concrete lining, ceiling, wall covering and paving to allow maximum offsite fabrication and activity overlap resulting in a one-year faster completion for traffic. The substantial changes proposed on a design-and-construct basis by the contractor and put into effect after State approval were: 1. Substitution of ductile iron and thick-wall P.V. C. pipes for clay pipes allowing placement and operation before hole-thru. 2. Outside pre-assembly of large rebar mats, using a novel tension-splice with cable clamps. 3. Arch concrete placement method modified to make 4, 322 ft. of lining in 10 weeks possible. 4. Safety barriers precast and epoxy coated offsite instead of cast-in-place and tile faced. 5. Prestressed hollow ceiling slabs with porcelainenamel coated steel sheets assembled offsite, instead of in-place glazed tile and in-place cast concrete ceiling. 6. Glazed tile wall panels 8 ft. long by 11 ft. high assembled off site and erected using vacuum pad mounted on special lift. 7. Asphalt paving while other work proceeded, instead of reinforced concrete slab and asphalt overlay. Work started in January 1968, but advance came to a one-year standstill for major structural redesign and negotiations of a new agreement during 1970. Using multiple drift construction followed by top-heading and bench excavation, it then progressed to hole-thru in July 1972. As a result of art 18-month overlap of activities the tunnel was opened for traffic only eight months later in March 1973. Gibbons and Reed Company of Salt Lake City, Utah sponsored the joint Venture of Al Johnson-Gibbons and Reed-Western Paving-Kemper during 1971, 1972, and 1973. The tunnel was the subject of a previous paper delivered at the RETC '72 in Chicago by R. C. Hopper, T. A. Lang, and A. A. Mathews, describing geology, unusually severe structural loading and multiple-drift tunnel excavation.

Jan 1, 1974

By C. L. Molina

The U.S. Geological Survey (USGS), in cooperation with the Bureau of Land Management (BLM), Geological Survey of Wyoming, and U.S. Bureau of Mines (USBM), will produce an estimate of the amount of available coal in an area about 55 Ian (35 miles) south of Gillette, Wyo., where the Wyodak coal bed is 8-27 m (25-90 ft) thick. Available coal is coal that actually is accessible for development under current regulatory, land-use, and technologic conditions. Local coal-development considerations include roads, ranches, railroads, pipelines, power lines, wildlife and archaeological sites, alluvial valley floors, cemeteries, and the Hilight oil and gas field and gas plant. Some of these considerations would be mitigated so that surface mining may proceed; others presently preclude mining in their vicinity.

Jan 1, 1995

By Donald L. Gaughenbaugh

Under the terms of the 1970 amendments to the Clean Air Act, the EPA established national ambient air quality standards for a number of pollutants. Sulfur dioxide (SO2) was one of these pollutants. These ambient air quality standards have had perhaps their biggest impact on the power utilities. In an effort to meet the air quality standards set forth by the EPA, utilities using high sulfur fuels have been forced to install flue gas desulfurization (FGD) systems. The majority of FGD systems in operation today are nonregenerable systems, that is the by-product of the system is disposed of, usually into settling ponds. Limestone slurry is the most common reagent used to remove SO from the flue gases. The calcium carbonate (limestone) slurry interacts with the flue gas, absorbing the SO2 and forming a by-product of calcium sulfate/sulfite which is disposed of.

Jan 1, 1986

By C. R. Stephan, N. B. Greninger, W. A. Slivensky

The U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) are participating jointly in a research program to evaluate strength characteristics and air-leakage resistance of various proposed seal designs for use in underground coal mines. Over 20 full-scale seals were constructed in the Bureau's experimental mine at the Lake Lynn Laboratory, air-leakage tested, then subjected to pressure pulses of 0.14 MPa or greater. A discussion on the experimental procedure, construction techniques, and the explosion and air-leakage test results is presented. Four types of construction material were used during this seal testing program: solid-concrete-blocks, low-density foam blocks, cementitious foam, and wood blocks. Only one of the solid-concrete block designs using a mortared thick wall survived the explosion and air-leakage tests. Most of the low-density foam block and cementitious foam seal designs were judged to meet the requirements to be considered a coal mine seal. One of the wood block convergence seal designs failed explosion testing. Based, in part, on these research findings, several alternative seal design constructions using low-density foam blocks, cementitious foam, or wood have been approved by MSHA for use in coal mines.

Jan 1, 1993

By Murdoch Mackenzie

"Organic Polymers used as gangue depressants are classified according to their chemical structure. Absorption mechanisms for these reagents at the mineral - water interface are reviewed. The method of selecting these reagents for a particular flotation system is discussed. Details are given of methods of reagent solution make-up and distribution. Plant addition policy is reviewed.”

Jan 1, 1986

By Donald O. Rausch, William E. Hawkes, Odin Jr. Strandberg

INTRODUCTION Kennecott Copper Corp.'s Tintic Div. Burgin mine is a 725 t/d (800 stpd) lead-zinc producer, located in the east Tintic mining district, 5.6 km (3.5 miles) east of Eureka, and 130 km (80 miles) south of Salt Lake City, UT. The Burgin mining complex includes three shafts, shop, dry, and office facilities, and a 454 t/d (500 stpd) flotation concentrator. Production and ser¬vice entry to the mine is through a 4.26-m (14-ft) diam concrete-lined production shaft, and a three-compart¬ment rectangular shaft. A connection with the Apex No. 2 shaft and the Burgin mine provides a second exhaust airway. Bear Creek Mining Co., Kennecott's exploration sub¬sidiary, began exploration of the Burgin mine area in 1957 with the sinking of the 335 m (1100 ft) deep No. 1 shaft. A station was cut at the 320-m (1050-ft) level of the shaft and extensive drifting, diamond drilling, and some winzing and raising confirmed the presence of a major lead-zinc ore body, the main portion of which oc¬curred below a hot saline water table. Surface facilities and the 4.26-m (14-ft) diam concrete-lined production shaft were completed in 1966. Ore production has been steadily increased to 725 t/ d (800 stpd) since 1966. The collar elevation of the No. 2 production shaft is 1731 m (5678 ft) above sea level. The mine's three levels, the 1050, 1200, and 1300 are at elevations of 1414.6, 1356.4, and 1338.1 m (4587, 4450, and 4390 ft), respectively. The approximate elevation of the hot saline water table is 1382.6 m (4536 ft). The earliest production on the east Tintic mining district was from the Eureka Lilly mine in 1909. Later, in 1916, the Tintic Standard mine was discovered, and pro¬duced ores with a gross value of $80,000,000 through 1956. The Eureka Standard mine located 1.6 km (1 mile) southwest of the Burgin mine produced ore worth $12,000,000 from fissures in the Tintic quartzite along the Eureka Standard fault. Ores produced from the east Tintic mining district through 1971 are valued at $151.3 million. The production from the entire Tintic district is approximately $500 million. GEOLOGY The Burgin ore deposit occurs as replacement bodies in limestone, dolomite, and shale. Numerous fault struc¬tures and rock formations make the mine geology com¬plex. The mineralization is strongly associated with sev¬eral major geological features, which include the Ophir formation, consisting of limestone, dolomite, and shale as the favorable host rock, and the structural influence of the east Tintic thrust, the Eureka Standard and sev¬eral other significant faults. Fig. 1 depicts the Burgin 1300 level workings, a generalized configuration of the ore body, and the main geological features. Covering the quartzite, limestone, dolomite, and shale facies enclosing the Burgin ore deposit are 183 to 274 m (600 to 900 ft) of andesite. The Burgin ore consists of massive sulfide and oxide lead-zinc ores with significant silver and cadmium val¬ues. The main ore minerals are galena, cerrusite, and spalerite. Extensive manganese oxide deposits are associated with the lead-zinc ore occurrence. A limited

Jan 1, 1982

By Ernest E. Thurlow

Introduction Today, more than 50% of rail-carried commodities are mineral industry related, with coal being the most important single commodity moved by rail. In 1980, coal accounted for more than 5.7 million of the total 22.6 million carloads moved by rail. Metallic ores were third behind grain, with more than 1.4 million carloads. Crushed stone, gravel, sand, and other non-metallic minerals totaled almost 2.3 million carloads. Chemicals and allied products, including fertilizer and coke, added another 1.7 million cars, with petroleum and petroleum products totaling 300,000 carloads. Coal Several things happened in the 1970s that gave rise to increased consumption of coal-particularly western coal-and to its dominant position among rail-carried commodities. First, the Clean Air Act of 1970 required generating plants to make significant reductions in sulfur dioxide emissions. To comply, utilities could either invest in scrubbers or switch to low-sulfur western coal. Many opted for the latter. By 1972, increasing demands by the utility companies halted what had been a 25-year decline in national coal consumption. Second, the Arab Oil Embargo of 1973 put an end to cheap oil and gas, limiting their future as fuels for electric generating purposes and increasing the potential for coal. Third, in 1977, President Carter announced an energy program with coal as its cornerstone, calling for an annual two-thirds increase in national coal production by 1985. He also called for conversion to coal by utilities and large industrial users. Finally, he proposed a 10-year, $10 billion program to encourage domestic coal production and stimulate development of export markets. Coal bounded into world prominence. Foreign demand for steam and metallurgical coal increased tremendously, while US demand for western coal also shot up. This meant greater demands on the transportation sectors that traditionally carried coal to market. Many railroads began programs to serve the coal industry. One example is Burlington Northern's commitment to handle increased western coal tonnages. The company spent more than $1 billion in recent years to develop a system capable of moving more than 91 Mt (100 million st) of coal each year. Other leaders in this renewal were Norfolk and Western, Union Pacific, Santa Fe, and Southern Pacific railways. The importance of the rapid growth of coal traffic to the railroads is shown in the accompanying table, which gives percentages of total tonnages hauled and revenues attributed to coal. With coal providing the railroad industry with a substantial share of its revenues, there is keen competition among the rail companies themselves and among railroads and other transportation sectors for coal haulage. But there is also cooperation when more than one railroad is involved in delivering the coal from mine to market or when a combination of transportation modes is more economical. The latter is represented by Conrail's interest in working with the port authorities of New York and New Jersey to establish a new coal port that would serve not only export markets, but also utilities and industries in the northeast. Iron Ore Next to coal, iron ore (taconite) is the most important single mineral commodity handled by railroads. In Minnesota, where most iron ore is produced, rail transportation is primarily by Burlington Northern and the Duluth, Missabe, & Iron Range Railway Co. (DM&IR). The DM&IR, owned by US Steel, serves several producers on the Mesabi Iron Range. Two of the larger producers, Erie Mining Co. and Reserve Mining Co., also own railroads that operate between the mines and the ports of Silver Bay and Taconite Harbor on Lake Superior. Several iron mines and taconite plants in Michigan are served by the Chicago and Northwestern, and the Soo Line. Total 1981 shipments of taconite and iron ore are estimated at 55.9 Mt (55 million It), compared with about 61 Mt (60 million It) in 1979 the most ever shipped in one year. Still, with annual production capacity of the eight Mesabi Range

Jan 10, 1982