Search Documents

By Grover H. Emrich

Pennsylvania,, due to its location in the humid east, is fortunate to possess within its borders large quantities of water. Most of the State is drained by three major river systems-the Ohio, Susquehanna and Delaware. This abundant supply of surface water has been widely utilized throughout the State, but today other sources of water must be developed due to the increasing demands for water, die largest undeveloped source of water in Pennsylvania is ground water. Pennsylvania is also fortunate to possess extensive coal resources. These coal resources have contributed measurably to the development and prosperity of the States Coal and water's - two valuable resources - have been necessary for the development and industrialization of Pennsylvania, The State needs both resources but can no longer afford to develop one while adversely affecting or destroying the other, We are aware of the effect of coal mining on surface water, but coal mining can also materially affect subsurface water, This effect will according' to the local geologic conditions.

Jan 1, 1965

By Stanley J. Gasior

Most bituminous coal mined near Eastern industrial areas requiring high Btu pipeline gas is caking and therefore unsuitable for fixed-bed pressure gasification by present techniques. If the caking property of such coal can be destroyed the resulting fuel can be gasified in a fixed bed at pressure with steam and oxygen as a preliminary step in making a high-Btu gas. To find a practical way to convert strongly caking coals of granular or small lump size to noncaking fuel was the object of this study. In previous work strongly caking coals of 1/8- to 1-1/2-inch size was converted to a noncaking coal char by treatment in a static bed in about 3 hours [1/]and coal of 18-100 Tyler mesh in a fluidized bed in about 5 minutes.[2/] An inert gas such as `steam, nitrogen, carbon dioxide, or a mixture of all three with a small amount of oxygen was used in both studies. In our work a strongly caking bituminous coal from the Pittsburgh seam of 4-8 Tyler mesh size was converted to a-noncaking form in free-fall in about 2 seconds by dropping it through a countercurrent flow of steam containing 4 to 7 percent oxygen at 1,150°-1,200° F and 300 psig. This method should also be applicable to smaller-sized material.

Jan 1, 1965

By R. W. Utley

The purpose of this study was to seek and evaluate possible relationships between the composition of coal refuse, as expressed by washability data, and factors affecting the product ion of a lightweight aggregate from refuse by bloating. The study was related to an intense program in the Department of Mineral Preparation at the Pennsylvania State University to study the possible elimination of air pollution from coal refuse fires by producing a low- carbon secondary refuse. Another phase of this program is considering possible uses of such a secondary refuse. Thus one study was to determine if a lightweight aggregate could be produced from this new refuse material and what effect the nature of refuse beneficiation would have upon the characteristics of a commercial aggregate product.

Jan 1, 1965

By George A. Komadina

The Pima Mining Company lies 20 miles southwest of Tucson, Arizona, and some 45 miles north of the Mexican border. The mill is situated on a hillside overlooking Tucson and the Santa Cruz Valley, the ground generally sloping northeast at a 2.5 percent grade. The hillside location allows for gravity flow generally through the plant as well as for: tailing disposal.

Jan 1, 1965

By M. F. Corcoran

Rapid advances have been made in the past few years in the application of automatic controls and instrumentation to iron ore pelletizing plants. Present practice in applying instrumentation and control to the Grate-Kiln system of iron ore pelletizing is described. Major control points and loops are tabulated. Future trends in the application of digital control including computer data logging systems are described.

Jan 1, 1965

By Warren E. Morrison

The expansion of the United States economy in the postwar period has had a tremendous impact on the demand for energy. Not only has total energy consumption increased at an unprecedented rate, but there have been major shifts in the composition or mix of energy resources within the end-use sectors. Because of the numerous interrelationships between substitutable energy resources and their markets, the energy economy can only be analyzed in terms of the trends of its component parts. This problem takes on additional complexity when attempting to chart the nation's future energy requirements. Total energy consumption can be forecast with reasonable accuracy for periods up to 15 years by relating this to projections of economic indicators. However, forecasting the component parts of the energy economy constitutes a dilemma in that the sum of the projected parts frequently exceeds predictions for total energy. Areas of uncertainty in energy forecasting tend to mount rapidly when proceeding from total energy to the consideration of specific energy resources consumed as fuel, power, or raw materials.

Jan 1, 1965

By T. L. Myron

In recent years increasing attention has been given to improving both the chemical and physical properties of sinter. The first step toward this goal was the production of a self-fluxing-sinter. More recently, blast-furnace operators have found that significant improvements in blast-furnace performance can be achieved by improving and controlling the physical size of the sinter. The results of full-scale blast-furnace tests have shown that blast-furnace production can be improved by using a closely sized agglomerate. The improvements obtained by the use of pellets, a closely sized agglomerate, are well known. In contrast, blast furnaces charged with sinter having a wide size spectrum have generally not yielded results as satisfactory as those from furnaces 1) * charged with pellets. Beginning in 1958, Appleby-Frodingham charged plus 3/8-inch sinter to their blast furnaces. Further tests by other companies in Canada, 2) the United States, 3) and Australia showed that blast-furnace production could be improved by about one percent when the plus 3/8-inch material in the burden was increased by one percent. Because of the promising results obtained with screened sinter, an extensive test program was initiated to determine an effective means of producing sized sinter in U. S. Steel's sinter plants. This paper describes the work done by the Applied Research Laboratory in this program.

Jan 1, 1965

By W. L. Chen

In the United States hydraulic cyclones have been used for thickening, classification and cleaning in coal preparation plants for many years. The cleaning cyclones presently in use are based on using a "heavy medium", such as a fine magnetite and water pulp. The latest addition to cleaning cyclones is the one which uses ?water only?, or simply called "Hydrocyclone". Just as was the heavy medium cyclone, the hydrocyclones were originated in the Netherlands (1, 2). Plants using hydrocyclones were built in Europe (3) and test plants were erected in Canada (4, 5, 6) and India (7). Roberts and Schaefer Company has built four plants using hydrocyclone circuits. One additional plant is in the process of construction.

Jan 1, 1965

By M. E. Volin

Reagent control for optimum concentrate yield was studied by laboratory batch flotation tests simulating the Groveland plant flotation circuit in which a rougher concentrate is cleaned twice. The reagents were a fatty acid collector, a sulphonate collector and sulphuric acid. The study included two types of flotation feed representative of the reground and deslimed tailing from the spiral concentration circuit, one when the ore mineral is predominantly specularite and the other when it is magnetite. The factorial design included three levels of fatty acid, five levels of sulphonate and five levels of H2S04, with the two types of ore in nested blocks, making up a total of 75 tests. Similarity of results and reproducibility were established in preliminary tests. The final tests were performed in random order under closely controlled conditions following the established procedure.

Jan 1, 1965

By William W. Magnus

The Eastern Magnesia Talc Company has always had the problem of adequate storage at its various mines and mills of not only crude ore and finished product but also material in process. An opportunity arose a couple of years ago with the decision to build a new mill at West Windsor, Vermont, (Figure 1) to come as close to providing adequate space for ore and the ground talc in the new plant as money and judgement would allow. Since our engineering staff did not have the time to design and engineer the new facility, an architectural firm with complete engineering staff was retained. Our original thought was to contract all phases of the construction and installation, however, and I think this is a most important point for any small firm such as ours, we found that with good supervision we, as the contractor, could do the job faster and at a lower cost than the construction firms that bid on the work. For some 50 odd years Italian talc has had a virtual monopoly in the body powder area of the cosmetic industry. Due to the purity, superior lubricity and whiteness, naturally occurring in the talc from Italy, no talc in the Western Hemisphere could capture any but a very small part of the market. When the Italian supply was cut off during World War II, the United States' largest consumer of this talc decided that it was time to develop a domestic source of a satisfactory replacement.

Jan 1, 1965

By Walter Kahn

Increasing consideration is being given to simplifying traditional methods of tracing pipelines and maintaining required temperatures of stored fluids. Because of their reduction in capital costs, virtual elimination of maintenance. ease of control and "cleanliness"; interest in electrical techniques has accelerated. 1,2 Resistance cable and other heaters have been given some attention. but less well known in the recent introduction of thermal conductive coatings. This paper is addressed to the use of thermal conductive coatings for heating fluid-transport piping and storage tanks. Emphasis will be given to the simplicity, efficiency, and versatility of design and application which their unique properties further contribute to the general economics of electrical heating.

Jan 1, 1965

By T. K. McMahon

Formally, a mathematical model could be defined as: A set of equations whose solution will approximate the response of a physical process or system to a set of stimuli which appear as parameters in the equations. The purpose of a mathematical model is to permit the rationalization of experience to proceed by simulation rather than by physical experimentation. In the application of digital computer control to an industrial process, the mathematical model of the process (subsequently called the process model) is needed to calculate the present process performance from the measured variables and to predict the response of the process to a control change. Functionally, the cardinal element in process model development is a concise set of control objectives. These, besides implicitly defining the boundaries of the system to be modeled, will determine the accuracy demanded of the model its nature: dynamic or steady-state, and so forth, The objectives should explicitly define what process efficiencies, production rates, qualities are to lie within the scope of the computer control project, thereby providing a basis for simplifying assumptions in the development of the model. This requirement, a limited set of control objectives, is so often disregarded in formulating industrial control problems that its repetition can scarcely be avoided.

Jan 1, 1965

By Ernest Hucke

This paper will cover basic pneumatic and electronic sensors, transducers, transmitters and their application in the Mining Industry.

Jan 1, 1965

By Jack G. Crump

Nuclear radiation systems for gauging solids content in process slurries and level in crushers has demonstrated acceptance in ore processing. The use of nuclear radiation for moisture analysis of bulk materials is presently receiving acceptance in beneficiating and agglomerating processes. On the horizon is the use of nuclear activation methods for continuous, qualatative and quantitative analysis of concentrate. The common characteristics of these uses of radiation is the non-contacting nature of the measurement. Unquestionably, this is the dominant reason for acceptance of nuclear methods in level and slurry-gauging. Moisture activation analysis of a product using nuclear methods retain this advantage. However, and: more importantly, they offer new solutions to old problems. The nuclear method in addition to being non-contacting, is non-destructive and provides a continuous measurement of the process variable. The system responds: to the fundamental makeup of matter, mass and elemental composition, not to secondary properties such as temperature, resistivity, or dielectric constant. Measurement is a volume rather than a surface phenomenon, thus the results can provide a truer pricture of the measured variable.

Jan 1, 1965

By Fred T. Towne

Recent developments in fine grinding by the means of mechanical impaction are the result of continuing improvements in modern machine construction. This is especially true when related to the bearings and mechanically operated parts of impact mills. These improvements allow manufacturers to increase the speeds of the impacting members Most of the more common forms of size reductions, such as percussion, pressure, friction and sectioning, or cutting were at one time accomplished by human hands. These actions were transferred to machinery. Originally of limited application, their use widened as industrial materials and construction became more sophisticated.

Jan 1, 1965

By William H. Engelleitner

Agglomeration by balling in cylindrical or shallow pan devices dates back to the early part of this century. The first sintering tests conducted by Dwight-Lloyd on nonferrous ores included a mixing step for ore, flux and fuel carried out in a deep pan device similar to the balling pans, or discs, presently in use. Further work directed mainly toward sintering of ferrous and nonferrous ores always included a preparatory step, usually referred to as mixing, agglomerating or green-balling of the ingredients. In the late forties and early fifties two methods of particle preparation prior to firing were in general use. In Europe the balling pan was used predominantly, both as a mixer and as a pelletizer. In the United States many pilot plants and semi¬commercial plants used balling drums. When the first iron ore pelletizing plants were built in this country, the most frequently used device for green-balling was the cylindrical drum. At the same time, the pan device was used both in Europe and the United States for many other materials such as fertilizer, cement, flyash, alumina and copper concentrates, as well as to mix the feed for sinter machines. The difference between these two balling devices - -the drum and the disc - has been the subject of much discussion and is well covered by several papers included in the 1962 publication "Agglomeration' issued by AIMS, based on their 1961 International Symposium held in Philadelphia. (1)

Jan 1, 1965

By C. F. Giermak

Over a considerable period of time great interest has been shown in selective dry concentration of fine ferromagnetic particles, although it is only recently that new permanent magnetic materials have been made available to permit building of such permanent magnetic separators. It is well known that the conventional drum separator does' not efficiently separate fine materials. The centrifugal force on any drum acts in accordance with the particle size and gravity, which may beat varying magnitude-.opposite to the magnetic force, especially when the material is not closely sized. The Magnetic-Mechanical Separator (MMS) is designed for the concentration of fine, unsized magnetic materials where the percentage composition of magnetics to nonmagnetics, or the nature and texture of the materials, is such that its unique agitation and shake-out action with no centrifugal force provides greater efficiency than is obtainable by conventional magnetic separation equipment. This machine consists of a complete double belt conveyor unit with a premagnetizing Axial Pole Agitating Pulley at the feeding end of the lower conveyor belt and a special agitating concentrator magnet above the lower belt of the upper conveyor.

Jan 1, 1965

By F. L. Pierson

Since the discovery of 'potash in the Carlsbad area in 1926 and the start of mining operations in 1931, "first mining," operations have been carried on. This is a room and pillar system in which approximately 62% of the total ore is removed. Or the basis of ore reserves and rates of extraction, the life of the mine in the early; days was estimated to be well over 50 years, however, even with an increase by additional ore reserves, it became increasingly apparent that the life of the mine was being shortened considerably by increased production. Further cause for the shortening of mine life was due to the exceptionally weak back over the northeast quadrant of the main orebody which had .caved in on first mining up to a height of 8 feet. Thus, in 1953 the decision was' made to begin pillar pulling, also called, second mining or final mining, and in December of 1953 this program was started after much discussion.

Jan 1, 1965

By Thon T. Gin

The lithologic, mineralogic, and magnetic beneficiation characteristics of the iron formation at U. S. Steel's Atlantic City Ore Mine, Fremont County, Wyoming, have been determined. The iron formation averages about 30 percent Fe content, and varies from 125 feet to about 500 feet in thickness. It is composed of interbedded magnetite-rich quartzites, magnetite-quartz-amphibole schists, and amphibole-chlorite schists. Quartz, actinolite-tremolite, chlorite, and magnetite are the essential mineral constituents. These rocks are differentiated into four major ore types on the basis of their relative quartz and amphibole content. The iron content of the magnetic concentrate decreases and the silica content increases with decreasing grain size and increasing amphibole content in each ore type at the same fineness of grind. Criteria were developed to enable the mine operator to recognize the ore types and to blend them to produce a more uniform concentrator feed. This results in less variation in product quality and requires fewer changes in operating conditions-in the concentrator.

Jan 1, 1965

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965