Search Documents

By Carlo Grandori

Early experiences The first double shield hard rock tunnel boring machine, manufactured in 1973, belonged to the generation of machines that were equipped with 12" dia. cutters. The experiences made with the 4.3 m diameter prototype ROBBINS mod 144-151 have been reported at the 1976 R.E.T.C. of Las Vegas (1): it might be worth recalling here that, with a specific cutter load not exceeding 10 to 12 metric ton and a 4.8 r.p.m. cutterhead speed, the average advance rate was of 350 meters per month of 21 working days with a peak production of 1,050 m of advance in 40 working days, in widely weathered and fractured granitic rocks of generally precarious stability, where a precast segmental lining was routinely installed as tunnel support. Over the 8.2 km of the Sila Tunnels, several badly crushed or sheared rock zones were bored through without major problems, even with water inflows of up to 30 1/sec. The same machine, with an improved design of the telescopic-and-floating shield area and equipped with flameproof drive motors, was taken to Colombia where, from September, 1979 to March, 1982 it drove 7.5 km of the Rio Negro-Chivor Tunnel in competent siliceous shales of up to 130 MPa at an average rate of 20 m/day.

Jan 1, 1987

By Malcolm Ross

Of the six forms of asbestos, only three have been used to any significant extent in commerce. These are chrysotile, crocidolite, and amosite. Between 1870 and 1980, approximately 100 million tonnes of asbestos was mined worldwide, of which more than 90 million tonnes was the chrysotile variety, about 2.7 million tonnes the crocidolite variety, and about 2.2 million tonnes the amosite variety. The three principal diseases related to asbestos exposure are (1) lung cancer, (2) cancer of the pleural and peritoneal membranes (mesothelioma), and (3) asbestosis, a condition in which the lung tissue becomes fibrous and thus loses its ability to function. These diseases, however, are not equally prevalent in the various groups of asbestos workers that have been studied: the amount and type of disease depend on the duration of exposure, the intensity of exposure, and particularly, the type or types of asbestos to which the individual has been exposed. Lung cancer is caused by exposure to chrysotile, amosite, and crocidolite asbestos; however, increased risk of this disease is usually found only in those who also smoke. Asbestosis is caused by prolonged exposure to all forms of asbestos, whereas mesothelioma is principally caused by exposure to crocidolite asbestos. There is good evidence that chrysotile asbestos does not cause any significant amount of mesothelioma mortality, even after very heavy exposure. The common nonasbestiform amphibole minerals, cummingtonite, grunerite, tremolite, anthophyllite, and actinolite, which are often defined as "asbestos" for regulatory purposes, have not been shown to cause disease in miners. Chrysotile asbestos, which accounts for about 95 percent of the asbestos used in the United States, has been shown by extensive Canadian studies to be safe when exposures do not exceed 1 fiber per cm3 for the working lifetime. Chrysotile dust levels found in buildings rarely exceed 0.001 fibers per cm3. Such dust concentrations will have no measurable health effect on the building occupants. Present and future controls of minerals defined as "asbestos" and removal of asbestos from buildings and homes may cost many billions of dollars. Much of this expense is unnecessary and even counterproductive. Asbestos abatement could in fact produce a health risk to those exposed to dusts during and after removal operations overly restrictive controls could force the use of poor or dangerous substitutes, and could greatly affect the hard-rock mining industry.

Jan 1, 1987

I found the article most interesting and timely. I consider it imperative that mine case studies like this one are undertaken and published so that the practicing mining engineer and geologist can obtain a better idea of what is the preferred estimation and grade control technique to use, given the site-specific geology, grade distribution, etc. Mining companies, with operating gold mines, need to be encouraged to either initiate such a study in-house or support a research project by financing a graduate student at a local university. The latter method is preferable since it not only provides research support but also an excellent training opportunity for young mining engineers and geologists. Ideally, what is needed is exploration drill-hole, blasthole, and mine production data that can then be used to assess the efficiency of different estimation and grade control methods by comparing the results obtained using the drill/blasthole data with the actual production data. It is hoped that more mining companies will realize that the rewards from this kind of research greatly outweigh the sometimes perceived problem with releasing data to a university. I noticed that the authors used the blasthole data to represent the actual values, the validity of which relies heavily on the two key assumptions with regards to blasthole assays and in-pit ore-waste selection procedures. Could the authors comment in more detail on these assumptions and what criteria they used to check the validity of the assumptions? Since the article was published, have the authors had the opportunity to compare their estimates with the actual production data? It would be interesting to compare other estimation methods with OK and IK. For example, how well did the polygonal method used at the mine compare with the results given in the paper? I would like to mention that B.L. Kwa completed a similar study (Kwa and Mousset-Jones, 1986) using exploration drill-hole, blasthole, and production data from the Alligator Ridge mine in Nevada. The study compared a variety of estimation methods, including IK, and the final results are shown in Fig. 1. The IK method exhibits the smallest difference between estimated and production results and is closely followed by the indicator moving window (Ind MW) method. Reply by Y.C. Kim We do concur with Professor Mousset-Jones with respect to the merit of such case studies performed at a local university. In answer to his request for comment on the validity of the two key assumptions made in our paper, we can only say that these are reasonable assumptions that are very difficult to validate. The assumption of blasthole assays being accurate can be partially validated by a careful analysis of the nugget component of blasthole variograms. The assumption that the in-pit ore-waste selection procedure in use was an effective one can only be validated through comparison between the mine estimates of ounces of gold versus the actual recovered ounces of gold at the mill. Neither one of these two assumptions has been validated to date due to several reasons. For example, the mine went through a change in management since the study. Similarly, no compelling reasons have been presented to perform detailed variogram analysis of the blasthole data. We do, however, believe that the obtained results (i.e., indicator kriging performs better than OK in a highly skewed deposit) will remain the same in relative terms, regardless of how valid these two assumptions may be. The most recent com¬parative study by D. S. Lindsey of the Montana College of Mineral Science and Technology also shows a similar ranking between ordinary kriging versus probability kriging, which is an extended version of indicator kriging.

Jan 1, 1987

By Russell E. Martin

Excavating and lining twin interstate highway tunnels each 11.3 m (37 ft) high by 14.6 m (48 ft) wide by 183 m (600 ft) long. A discussion of the geology of the site and problems occurring at the portals and the solutions to the problems. The methods used in placing the concrete lining are also discussed.

Jan 1, 1987

By A. E. Hall, D. M. Mchaina

This paper outlines a proposed research project to investigate secondary sulphide ignitions. Sulphide dust explosions have resulted in loss of production and considerable capital and equipment replacement cost in Canadian mines. The practical application of laboratory test results to actual mine situations presents a complex problem and is a field requiring immediate investigation. The factors contributing to the outbreak of sulphide ignitions are not clearly understood. This indicates a need for future research to study the influence of blasting parameters, exhaust temperatures, and dust characteristics on secondary ignitions at source. The aim is to establish realistic quantities for each of the parameters and develop a model that will incorporate field and laboratory quantities. It may be possible to predict outcomes of sulphide ignitions when the parameters are known. It is also planned to study the techno-economic feasibility of the preventive and control methods. One aspect of planned future research requires quantification of some terms by obtaining measurements of pollutant concentrations and size distribution of the airborne dust in an underground environment immediately after a main blast. A blast-proof aerosol sampling package to measure the source term will be designed. This sampling package will consist of a sampling section and a shield which will be capable of withstanding a blast explosion. The accuracy in measuring the variables and combination of variables will be the main focus in this proposed study.

Jan 1, 1987

By H. Sevim

A new method of designing haulage systems, consisting of belt conveyors and hoists for underground mines is discussed in this paper. Efficient and economic design of such systems will prevent operational bottlenecks and provide savings. The developed model uses a heuristic algorithm to optimize the design parameters and to select the proper equipment specifications. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate belt conveyor networks of any configuration and hoisting systems that can be either drum or friction hoists for single or multiple-level operations. The model also has the option to internally determine the required capacities of the bunker(s) and shaft- bottom bin. The objective of the optimization process is to minimize the "expected cost per ton of ore hauled" from the working faces to the surface. A numerical example is included to illustrate the capabilities of the model.

Jan 1, 1987

By B. J. Timmons

An initial point that I would like to make very emphatically?and as our title might erroneously suggest for those of you old enough to remember . . . Peter Harben and myself do not intend to shoot ourselves in the foot. We derive our livelihood from a number of aggregate, industrial and other minerals producers, both here in the United States and outside. This paper, therefore, is a fence-straddler or for information purposes (we hope) only, rather than any "fur or agin" stances. In essence, some of you may consider it a U.S.G.S. publication! In fact, we hope that it serves to inspire aggregates producers to do some radical thinking, to promote introspection, and to that end it would benefit both domestic and foreign producers. The title could be shortened into a brief question of "Aggregates Travel?" with an emphatic no for the answer. In the past, the success of a construction materials venture depended upon your ability, through siting, to provide the customer f.o.b. the job site, a product at the lowest possible cost.

Jan 1, 1987

By V. K. Gupta

A detailed laboratory study was carried out to investigate the effect of the particle size distribution on the grinding rate parameters, Si, for the dry ball milling of quartz and limestone. Contrary to the present belief, the Si values were found to vary strongly with the particle size distribution. In particular it was observed that: (i) the Si values increased with the fineness of the particulate charge - the increase being more pronounced in the case of the coarser sizes, (ii) the next finer size class had the maximum effect on the breakage of the particles of a given size class, while the coarser size classes had only a slight effect, (iii) the effect of two or more size classes was non-additive, and significant higher order inter-size interactions were indicated. The importance of these results in the context of the analysis, design and scale-up of the comminution systems is discussed.

Jan 1, 1987

By John A. L. Campbell

Are safety concerns justified regarding the potential for a gas explosion due to recirculation when a scrubber is used on a continuous miner? The role of a respirable dust scrubber on a continuous miner section using blowing face ventilation is examined in this paper and the above question answered. Methane control using high efficiency scrubbers coupled with blowing face ventilation is promoted.

Jan 1, 1987

By Paul C. Miclea

Hanford Reservation, in the State of Washington, with its deep basalt formations, is one of the three sites recommended by the Department of Energy for detailed investigations in order to select the first nuclear waste repository in the United States. Information obtained from several deep bore-holes drilled at Hanford indicates that the underground facility can be developed in one of the major basalt flows belonging to the Grande Ronde Formation in the Columbia Plateau, at depths greater than 3200 ft. One of the main concerns in the underground repository design is the achievement of acceptable environmental conditions during the development and the operation of the repository. For this, ventilation and air-conditioning are of prime importance and should be fully addressed. Besides the factors that determine the airflow requirements to meet the personnel and equipment operation needs, there are two major concerns that impact on the ventilation system design: the temperature of the in situ virgin basalt rock and the influx of groundwater. These two factors are related by the fact that the groundwater has the same temperature as the rock itself and they both constitute main sources of heat underground. Current information indicates that the temperature of the virgin rock at a depth of around 990 m (3250 ft) is 52°C (12S°F). However, there are some indications that the rock temperature at the selected horizon might be higher. This paper addresses the impact of the virgin rock temperature on the ventilation system and air-cooling requirements. Graphs with heat loads and cooling required for different rock temperatures have been prepared for a given model and network, using computer techniques for simulating the climatic parameters.

Jan 1, 1987

By James E. Monsees

Extensive underground excavation will be required for construction of a mined geologic repository for nuclear waste. Hundreds of thousands of feet of drift will be required based on the conceptual layout design for each candidate nuclear waste repository. Comparison of boring and blasting excavation methods are discussed, as are special design and construction requirements (e.g., quality assurance procedures and performance assessment) for the nuclear waste repository. Comparisons are made between boring and blasting construction methods for the repository designs proposed for salt, volcanic tuff, and basalt. Differences in the geologic media and settings of the prospective sites influence the excavation method in terms of drift length, size of opening, drift slope, rock quality, and boreability. Support requirements, ventilation, and the ability of the geologic system to retard radionuclide migration are also directly impacted by the geology and excavation method.

Jan 1, 1987

By Joe M. Bryan, George E. Rodger

The development of small precious metal mines in the western states has been directed at heap leach operations. Crushing plants are an essential adjunct to heap leach operations. They must meet environmental air quality regulations which generally follow a similar pattern from state to state. Prior to mine construction a permit must be obtained and an operating permit granted during or shortly after the start-up period. The typical construction permit application consists primarily of drawings, specifications and an explanation sufficient to indicate that the mass of particulate matter entering the atmosphere is below minimum standards. The operating permit may be granted following demonstrations that air emission control equipment or methods comply with information submitted in the construction permit application.

Jan 1, 1987

By R. D. Hagni, R. T. Brandom

An ore microscopic study of the Boss-Bixby, Missouri, copper-iron deposit has shown that the mineralization formed as a simple sequence of oxides followed by cobaltian sulfides, copper-iron sulfides, and then oxides. The hypogene ore minerals found by this study are magnetite, hematite, ilmenite, rutile, chalcopyrite, bornite, covellite, cobaltian pyrite, carrollite, sphalerite, clausthalite, galena, electrum, scheelite, wolframite, and a Pb-Bi-Se-Te mineral. Textural evidence indicates that some of the early oxides were original constituents of the host syenites and oxidized during cooling. The remainder of the mineralization formed as breccia fillings and replacements. Subsequent partial oxidation has formed martite, covellite, rutile, and anatase.

Jan 1, 1987

By D. M. Avant, A. J. Solomon, S. M. Pickering, W. R. Fox

Introduction Most high purity silica is produced from crystalline quartz, generally from sand. However, there is a small area of southern Illinois where a porous, friable white chert rock is found that is very different in physical form from quartz sand. This microcrystalline material, commonly referred to as tripoli, is more easily ground to micron sizes than sand. Although of similar Moh's hardness, microcrystalline tripoli is less abrasive than either ground quartz sand or many synthetic abrasives. Location The southwestern corner of Illinois is underlain by extensive deposits of very porous chert; in some places the material is quite white. Two companies, Illinois Minerals Co. and Tammsco Inc., mine and process this white material. The Illinois Minerals plant is located at Elco, and the Tammsco plant is in Tamms, IL. Both companies mine from various locations within a 10-mile truck haul of their plants. Production from this district has been continuous since at least 1915. Malvern Minerals Co. mines and processes a generally similar microcrystalline, friable novaculite near Hot Springs, AR. Geology The southern Illinois white tripoli area is on the southern flank of the Illinois Basin. The commercial silica zone is a facies of the Clear Creek chert of Lower Devonian Age. To the north, where it occurs deep in the basin, the Clear Creek is a siliceous limestone. In the mining area, thin overburden has allowed access by surface ground water, which has leached away the carbonate content and left a quite pure silica residue. Fossils characteristic of sea bottom deposition, such as brachiopods and trilobites, are occasionally encountered in mining. The structure of the mining area is poorly known, due to infrequent outcrops. Strata in most mines are inclined at dips of 5° to 20°. There appear to be occasional high angle normal and reverse faults, but these are seldom of any significance in mining. The friable white silica zone mined in the Clear Creek chert is overlain by dark brownish-red chert and siliceous shale. Exploration drilling to date has not encountered the base of the microcrystalline tripolitic zone. Chemical content Leaching by ground water solution has removed virtually all the carbonate from the original siliceous limestone. Impurities encountered are red to yellow iron oxides, aluminous clays, and occasional black manganese oxides. The silica has no detectable formula water. A typical chemical analysis and physical properties are listed in Tables 1 and 2. Mineralogy and crystallinity Southern Illinois friable tripoli appears amorphous under the polarizing microscope. No crystal structure and only occasional, vague, patchy anisotropism is evident. However, the material gives an excellent quartz X-ray diffraction pattern. Thus, so far as X-ray mineralogy is concerned, the material is clearly

Jan 1, 1987

By S. P. Mehrotra

In this review article, various approaches and mathematical models that have been used to simulate, design, and synthesize flotation circuits are examined. First, a brief review of flotation kinetics is presented which is followed by a discussion on simulation of flotation circuits. The existing literature on optimal design of flotation circuits has been divided into two broad categories. In the first category, a generalized integral approach is used wherein the optimal circuit design involves determination of both optimal interconnection of various flotation cells/ banks of cells in terms of structural parameters and optimal values of various operating parameters. In the second category, a conventional circuit configuration is assumed to be the best configuration; the optimal design here only means the optimization of operating parameters. The merits and demerits of these two approaches are discussed.

Jan 1, 1987

By D. W. Park

Underground openings resulting from coal mining activities have been a serious cause of subsidence problems in the Warrior coalfield of Alabama, which is the 11th largest coal-producing state in the United States (National Coal Association, 1986). The problem will be even more serious in the future because 17 Gt (19 billion st) of Alabama's 22 Gt (24 billion st) of coal reserves are classified as an under- ground resource (Tolson et al., 1982). Subsidence data in this area has been scarce com- pared with other coalfields (Conroy, 1980; Dunrud and Osterwald, 1980; Gentry and Able, 1978; Hunt, 1979; King and Gentry, 1979). This paper discusses the results of a study of subsidence overlying two longwall mines that contrast each other. One of them (Mine #1) is a shallow longwall mine where the coal strength is very high, and the other mine (Mine #2) is extremely deep with a low strength of coal.

Jan 1, 1987

By Gemei Yang, Yihui Zhao

In caved goaf, the friction loss of fluid head is: [h = (R'+ R/Q/ )] Q (for one-dimensional transition flow). The R' and R, which are the functions of two dimensional spaces, are calculated through an empirical formula. Then, the bulking factor and permeability are determined. It is supposed that the airflow in porous media are similar to those in tiny tubes crossing each other. Therefore, the network calculation technique can be used to tackle the field transition flow problem. A lot of case studies showed that the emission of methane in mines mainly depends on the air velocity and has little relation to air pressure. Summing up our experience and experiments, we provide an empirical formula to calculate the gas emission rate per unit area. By means of mass conservation and network calculation, the methane content distribution in steady-state is worked out. Then the dynamic change in airflows and gas content can be analyzed by the characteristic-difference method.

Jan 1, 1987

By S. Chander

The use of various electrochemical techniques to study mechanisms of sulfide mineral- flotation reagent interactions is briefly reviewed in this paper. Prior to such studies it is desirable to thermodynamically determine solution conditions favorable for formation of hydrophobic species deemed to be responsible for flotation. The thermodynamic equilibrium involving both the stable and metastable species can be conveniently represented by an Eh-pH diagram. Thermodynamics can also be used to predict conditions where a mineral might not float if depressants are present. Under favorable conditions of flotation there is competition between reactions leading to formation of hydrophobic species with reactions that lead to formation of hydrophilic species. Due to the sluggish nature of the reactions involving sulfide minerals, a knowledge of the kinetic behavior of the system is necessary. Electrochemical methods of investigation are wed in laboratory studies to (1) control the state of oxidation, (2) determine the type and amount of electroactive species present at the mineral surface, and (3) study kinetics of electrode processes. By combining electrochemical techniques and wetting measurements the identification of hydrophobic species that might be present at the mineral surface could be achieved. Both contact angle measurements at mineral electrodes or flotation in a cell equipped with a particulate bed electrode can be used for the wetting measurements.

Jan 1, 1987

By Frank Hagar, George M. L. Robinson

NTRODUCTION The Resource Conservation and Recovery Act and CERCLA (SUPERFUND), in many instances, has had an adverse economic impact on the hardrock mining industry. Over the last few years, many abandoned and active mining operations have been added to the Environmental Protection Agency (EPA) National Priority List (NPL) . When the property is placed on the NPL the operator or EPA is required to conduct extensive environmental assessments to determine if historical mining practices have degraded the existing environmental. If degradation has or will continue, the responsible party is required to implement appropriate remedial action plans. If a responsible party is not identified, the EPA implements a cleanup program. Experience has demonstrated abandoned and active mining operations are subject to RCRA, and possibly Super- fund, if the mine has not adopted appropriate hazardous waste disposal management procedures. If off-site contamination has occurred, the operator will be required to mitigate the impacts and will be required to adopt additional procedures to minimize future impacts. Since the passage of RCRA and Super- fund, many mining operators are adopting management procedures to monitor and inventory hazardous sub- stances and wastes generated, stored and disposed on site. Many operators are in a difficult position because ore, waste rock, process chemicals or other solid waste, in many instances, can be classified as hazardous waste. If the process or other solid waste is deemed to have the characteristics of a hazardous waste, the operator can inventory and adopt appropriate, in- expensive management procedures. However, if the ore or waste rock has hazardous waste characteristics, in- expensive control technologies are impossible to implement. Since existing statutes and regulations require hazardous waste control, the operator will be required to inventory, characterize and monitor all aspects of the mining operations including but not limited to exploration, mining, ore processing and waste disposal. During this process, geological, geotechnical, geochemical, waste and ore volumes, and process materials must be tracked throughout the mining process. To accomplish this task, the most cost effective method to maintain documented and accurate records, is through the implementation of an integrated database management system. The database management system can be used to model and simulate the entire mining operation and if necessary, used to predict whether the operation is in compliance with existing regulations. The developed database can also be used to operating optimize mining and disposal costs.

Jan 1, 1987

By H. Sevim

An innovative approach in designing the haulage systems for underground coal mines is discussed in this paper. The haulage systems are formed by serially connected components. Therefore an economic and efficient design of the entire system is necessary. The computer model that uses a heuristic algorithm solves this design problem globally in a single run. It is a probabilistic model because it considers the probabilistic aspects of face operations. It is versatile because it can accommodate any type of mining and belt conveyor network configuration. The hoisting section can be used to design drum or friction hoisting systems for single or multiple level operations. These systems can have two skips in balance or a skip and a counterweight in balance. The model also has the option to internally determine the capacity of bunker(s) and shaft-bottom bin. The objective is to minimize the expected cost per ton of coal hauled from the coal faces to the surface. At the end of the paper is an example that illustrated the capabilities of the model.

Jan 1, 1987