Search Documents

By B. C. Cornilsen, X. Shan, D. H. Carlson, J. H. Johnson

Airborne respirable Diesel Particulate (DP) presents an additional health hazard in that it has been shown to be mutagenic. This problem is of increasing concern as more coal mines introduce diesel vehicles. If the DP present in coal mine air is to be controlled it must first be measured. This paper describes development of the laser Raman spectroscopic measurement of the amount of DP in DP/coal mixtures collected on filters in the laboratory and in coal mines. The Raman technique provides a chemical measure of the carbonaceous material in each component, and is not dependent upon particle size. When this work was begun there were no known analytical methods for this measurement. Side-by-side in-mine comparisons of the results obtained from Raman, neutron activation analysis, and size selective analyses (MOUDI and personal samplers) are presented. The neutron activation and size selective analyses were obtained by the USBM Twin Cities Research Center and University of Minnesota. Good agreement has been found among these three methods.

Jan 1, 1991

By S. Kraemer

Consumption of plastics has been growing in both the U.S. and world markets since the mid-1930s. This growth is due to plastics being used to make new products and as a replacement material for existing products. This paper develops an understanding of the replacement process by looking at the use of plastic, specifically PVC, in the construction pipe industry. History details the growth of the plastics industry and a discussion of the material selection process indicates the advantages and disadvantages of plastic pipe. Analysis shows that the use of plastic, as an alternative material for pipe, is having a significant effect on the cast iron, copper, clay, and steel industries. For the purpose of understanding the replacement process, three example residential systems were examined with a lifecycle cost analysis being performed. PVC was the material of choice in 1988 for all systems. Even though disposal cost was the one area where PVC was not the most cost effective, disposal costs were not sufficient to offset the overall advantage of using PVC on an economic basis. That plastic competes effectively with other materials, in terms of material properties and cost, indicates that further work should be performed to understand the impact plastics have on other material markets.

Jan 1, 1991

By S. K. Sharma

The Bureau of Mines' Tuscaloosa Research Center is conducting research to develop a basic understanding of solid-liquid separation in order to improve the dewatering of fine particle slurries. In the present investigation capillary suction time (CST) of kaolin slurries was determined. The average specific resistance of the cake was also determined by fitting the CST data to the theoretical equations used in this paper. The experimental data were analyzed by a powerful computer-based method, chemometrics, that uses statistical techniques to remove error and to find the number of physically significant factors contributing to the data. Results showed that two significant factors explain the CST data.

Jan 1, 1991

By Robert D. Rogers

The demand for phosphate will continue into the future, because phosphate is currently irreplaceable as a plant nutrient and in many chemical applications. Phosphate is not recycled, so the supply must be replenished through a process of mining and purification. Numerous microbial isolates. obtained from the environment were screened find those which demonstrated the greatest promise of solubilizing PO4 from the ore of interest. Screening was accomplished in a step wise manner an agar plate bioassay, shake flask studies, and semi continuous growth conditions. It was found that with the proper conditions of nutrient supply and solution pH; the bacteria and. fungus used in the semicontinuous process were able to solubilize in excess of 80% of an Idaho rock phosphate ore (RP) within nine days. A significant amount of solubilization occurred within the first six days. There was a 'reasonable correlation between the occurrence of soluble Ca and PO.4 during the processing of the RP thus providing evidence that the RP was being disintegrated by the organisms. In all cases, HPLC analysis of the solutions in which PO4 had been. extracted from RP showed that organic acids, which have been implicated as the mechanism of solubilization, were present.

Jan 1, 1991

By S. G. McDowell

Automation techniques are used during the design stage of continuous miners to decrease the time required and ensure the accuracy of the design. This is followed by automated manufacturing processes to reduce manufacturing time and improve the quality and consistency of parts. Combined, the result is a more reliable machine that can provide ongoing production capability. With the use of automation to enhance operator effectiveness and monitor machine condition, the productivity of machines is also improved. Productivity of continuous miners doubled over a 10-year span (Fig. 1). Although this article focuses on the continuous miner, it should be recognized that production increases of the continuous miner would not be realized without increased capabilities throughout the rest of the mining system. There are several aspects of automation that have played a role in providing increased continuous miner productivity. Though some are considered indirect, they still had significant influence on the overall result. Basically, productivity increases are obtained by cutting, loading and transporting the coal at a maximum rate. In addition, these tasks must be consistent, with minimal downtime. Therefore, the miner had to improve in operational capability and reliability. Automation techniques used during machine design, manufacturing and operation have all played significant roles in achieving higher productivity.

Jan 1, 1991

By M. R. Yenchek

The U.S. Bureau of Mines has determined a method for calculating coal mine portable power cable thermal life for a specified temperature loading. This work was the culmination of a multifaceted research project involving (1) accelerated life tests of insulation and jacket materials and (2) steady-state and cyclical loading of cables. Composite Arrhenius curves were derived for common insulation and jacket materials to identify the key cable quality that precipitates thermal failure. Plots of temperature rise versus current for popular cable sizes were then referenced to develop a correspondence between cable life, based upon thermal degradation and current loading. Predictions of cable thermal life were made through integration over variable load cycles and, consequently variable operating temperatures. This procedure may have utility for both the U.S. Mine Safety and Health Administration and mining machine designers in determining the appropriate cable size for new equipment.

Jan 1, 1991

By M. Z. Rashad

The intersections of numerous joint sets at the surface of tunneling region of Abu-Tartour-Project in Egypt create blocks with irregular shape and size in the rock mass. Most of these blocks are not able to move into the free space of the tunnel. Few key blocks are in a position to move and as soon as they begin so, some restrained blocks will be liberated. The aim of this work is to find the (removable) key blocks for walls, floor, roof and corners of a portion of the tunnel under jointed surface rocks; and then determine the best tunnel direction.

Jan 1, 1991

By J. R. Muhm

Environmental due diligence investigations, also known as Phase I Environmental Audits, are increasingly important to major investors, venture partners, or prospective purchasers or sellers of mineral properties. Knowledge of environmental risks associated with a property will allow better appraisal of a property's overall desirability prior to completing the transaction. It is possible that the cost of environmental cleanup could exceed the value of the property. Topics appropriately investigated include permit status, water quality, past use of the property, hazardous materials management, storage tanks, public records pertaining to the environmental character of the property, and environmental costs.

Jan 1, 1991

By Boyd G

This paper describes the planning, analysis, design and operational experience of highwall mining based on auger drilling techniques applied to thick coal seams exposed in an opencut highwall. Being the first time such technology has been used in Australia, a large commitment to technical design and logistics planning was given by Callide Coalfields Pty Ltd. This commitment included technical and operations management and supervision, mine services, and the retention of consultants to undertake geotechnical analysis, instrument preparation and instrument installation.

Jan 1, 1991

By Zwaan J, Kepa J

Ok Tedi mine has become one of the major copper producers in the world. In the process of becoming of age, it overcame the challenges of operating in a locality which is young in geological terms, experiences very high rainfall and has a topography which gives rise to frequent landslides. This paper discusses some of the geological, mine and geotechnical engin- eering aspects of the Mt Fubilan ore deposit.

Jan 1, 1991

By D. L. Sober, D. Ince, T. V. Vasudevan

Separation of dolomite from Florida phosphates was achieved by first conditioning the feed with fatty acid at pH 10 followed by reconditioning at pH 4 or below, before flotation. Observed selectivity of this two-stage conditioning process was attributed to the amount as well as changes in the nature of adsorbed collector species upon reconditioning. In this paper, bench-scale flotation results of optimizing the major process parameters, such as reconditioning pH and collector dosage, for upgrading natural high dolomitic phosphate samples from Florida are discussed.

Jan 1, 1991

By R. W. Barbaro, R. V. Ramani, K. V. K. Prasad, P. T. Luckie

The limitation of sulfur dioxide in power plant In this study, the following quality parameters of the coal emissions dictates that sulfur in coal be reduced to the lowest possible level before combustion to not aggravate the emission control problem at the stack. For coal-fired power plants, the methods in practice to achieve low-sulfur coal include mining areas with relatively low sulfur, reducing sulfur in the mined coal through preparation techniques and blending high- and low-sulfur coals. A prerequisite to the successful implementation of any of these practices is the knowledge of the spatial distribution of sulfur and the capability to predict its value in mining blocks. In this paper, the results of a study conducted to evaluate the applicability of geostatistics for describing the short scale variability of sulfur in a coal seam are presented. Four sides of a block of coal to be mined by the longwall method were extensively sampled at closely spaced intervals. The details of the longwall sampling plan and analysis procedures are discussed. The results of the statistical and geostatistical analysis are presented. The implications of these for prediction of sulfur for control purposes are examined.

Jan 1, 1991

By Terry S. Maley

With some exceptions, minerals may be acquired on the unappropriated public lands by one of three methods: (1) mining claim location under the General Mining Law of 1872; (2) mineral lease under the Mineral Leasing Act of 1920; and (3) sale contract under the Mineral Materials Act of 1947. Leasable minerals such as oil, gas, coal and phosphate are specifically designated as leasable in the Mineral Leasing Act so the method of acquisition is clear. As a general rule, metallic minerals are acquired by mining claim location. However the nonmetallic minerals, most of which are industrial minerals or gemstones, present a more difficult problem. These minerals are acquired either by mining claim or a sale contract depending on their chemical composition, physical properties and the use to which they are put. The Act of July 23, 1955 (30 U.S.C. 61 1) provided that uncommon varieties of sand, stone, gravel, pumice, pumicite or cinders are locatable; whereas, common varieties of such minerals may only be acquired by a contract of sale. The widespread location of mining claims to appropriate such deposits has caused many land management problems. Federal court and Interior decisions offer the most useful guidelines in determining the most appropriate method of acquisition.

Jan 1, 1991

By C. O. Hamilton

Poor plant start-up performance is usually blamed on poor design and unsatisfactory equipment. But, in most cases, the real cause of poor performance is inadequate preparation for operations and maintenance. Inadequate maintenance preparation, unlike inadequate operations preparation, will not immediately manifest itself in a new plant. However, not taking advantage of the window of opportunity afforded a new plant to organize the maintenance operation ensures that the new equipment honeymoon is unexpectedly short. Also, once a plant has entered a “breakdown mode,” it is extremely difficult to turn around.

Jan 1, 1991

By F. Allen Meek

The Upshur Complex of Island Creek Coal Corp. consists of approximatly 35.000 acres of both surface and deep mine researves located in Upshur County West Virginia. The principle seams on the researve are the Middle and Lower Kittanning. Other mining in the area during the late 1960's and early 1970's produced surface mines that exhibited severely acidic drainage characteristics both during the mining phase, and after reclamation was completed. The Buckhannon River, the principal drainage for the area, is a high quality, lightly buffered stream, that is periodically stocked with trout. Because past mining had caused post mining acidic discharges and the Buckhannon River was a valuable recreational resource, mining permits for the area were put on hold by regulatory authorities, until solutions to the acid mine drainage questions could be addressed. In 1978, the director of the West Virginia Department of Natural Resources appointed a Task Force consisting of Industry, Regulatory. and Academlc participants. This Task Force was charged with gathering information and evaluating field procedures used during mining to prevent acidic mine drainage. In 1979, the group published a document titled "Suggested Guidelines for Mining in Potentially Acid Producing Overburdens" which summarized material handling and mining procedures that could be employed to help prevent the occurrence of post mining acid mine drainage. In 1982, a Technical Advisory Committee was appointed consisting of well known researchers in the field of acid mine drainage prediction and prevention. The group was charged with the task of conducting research in the field of acid mine drainage prevention. Mining conducted at the Upshur Complex between 1979 and 1986 employed various acid mine drainage preventative techniques recommended in the suggested guidelines manual and techniques concurrently being researched by the Technical Advisory Committee. Costs for the various techniques were documented and the resulting post-mining water monitored. The results of these evaluations are used by Island Creek in the planning of future mining operations in potentially acid prodcuing environments

Jan 1, 1991

Develop a safe, efficient filter for removing diesel particulate matter (soot) from the exhaust of underground mining machines equipped with water scrubbers. Approach The Bureau of Mines and the Donaldson Company, Inc., jointly developed a low-cost, disposable, pleated-media filter (PMF) system. The system is intended for use on Part 36 permissible equipment or other machines equipped with water scrubbers. The PMF is installed downstream of the water scrubber to take advantage of the cool exhaust produced by the water bath. This demonstration system was tested on three Jeffrey 4114 Ramcars and a Wagner LST-5 scoop at Utah Fuel Company's Skyline mine near Scofield, Utah. Figure 1 illustrates a clean filter element being inserted into the canister on the Ramcar. How It Works The PMF system consists of a water trap, an optional over-pressure relief valve, filter canister, and PMF Under normal operations exhaust from a vehicle equipped with a water scrubber is heavily laden with water, especially on immediate startup of the engine. The water trap is designed to remove most of the water droplets from the exhaust before they enter the PMF, thus improving PMF performance. The over-pressure valve is designed to limit the exhaust backpressure by venting off some exhaust gas before the: filter. It is attached to the water trap upstream of the PMF. Figure 2 illustrates and shows a break out sectional view of the location of the PMF on the Ramcar.

Jan 1, 1991

By Tom Donnelly, Roger C. Ilsley

Remote telecommunications seismographs were used to monitor blast vibrations at two historic structures in Cedarburg, Wisconsin during adjacent sewer line construction. The purpose of the vibration monitoring program at the historic structures was to maintain blast vibrations below limiting tolerances established by the Wisconsin State Historic Society.

Jan 1, 1991

By Virgil J. Stachura, Larry R. Fletcher, Paul V. Sterk, Matthew N. Plis

The large diameter blastholes now being used in underground mining have caused concern because of their increased potential for damaging openings and creating rockfall hazards. In response to this situation, the Bureau of Mines is conducting research to reduce the amount of overbreak and damage to the perimeter of underground openings. This paper presents the results of tests with decoupled charges in 6.5 inch diameter blastholes, and unloaded guide holes, in Vertical Crater Retreat (VCR) stope panels at the Homestake underground gold mine in Lead, SD.

Jan 1, 1991

By Geisler P, Sutherland P

The technical limits for high-pressure transport of large particle solids by means of sludge pumps, piston pumps or the like lead to the development of the pipe-feeder system. The pipe-feeder is a type of pressure lock in which the high-pressure pump itself is not in contact with the solids. Simultaneous operation of the three chambers with corresponding control of the valves allows continuous flow in both the primary and secondary circuits. Initially the pipe-feeder was used only for the transport of solids. Today it also operates with great success in central mine cooling systems, serving as an alternative for high-pressure/low-pressure heat exchangers or Pelton systems. In addition to the technology applied up to now, the pipe-feeder is also capable of transporting ice slurry, thus increasing cooling output consider- Ably.

Jan 1, 1991

By John C. LaScola, Gerald L. Finfinger, Michael A. Trevits

Methane gas is an ever-present problem facing the underground coal mining industry. Mine operators are mandated by law to maintain safe concentrations of methane gas within the mine environment. Ventilation is the method of choice used by all mine operators to reduce gas concentrations. When gas emissions are such that ventilation alone cannot control the gas, methane drainage methods must be applied. In the 1970’s, there was a concern that unprecedented gas emissions would be experienced as mine operators began new developments in the deep and gassy Blue Creek and Pocahontas No. 3 Coalbeds. Such concern was well founded as significant gas volumes are being emitted as these mining operations mature. In 1971, the U.S. Bureau of Mines began to tabulate and track the change in mine emissions. These data were extracted from the underground coal mine quarterly air quality-quantity inspections performed by the Mine Safety and Health Administration. At that time, approximately 6560 Mm3/d (231.7 MMcfd) of gas were emitted from 430 underground coal mines. It was determined however, that the mines emitting less than 2832 m3/d (100 Mcfd) contributed only 2.1 percent of the total daily gas flow. In 1988, underground coal mines emitted 8350 Mm3/d (294.9 MMcfd) from 487 mines. This report evaluates the changing nature of U.S. mine gas emissions over the last 18 years.

Jan 1, 1991