Search Documents

By Peter N. Gabby

A mineral survey of 8,300 acres of the 24,980-acre Burnt Creek Wilderness Study Area (ID 45-12), was conducted by the U.S. Bureau of Mines in 1985 at the request of the Bureau of Land Management. The study area is located in Custer County, ID, 90 miles northwest of Idaho Falls. No mines, claims, or prospects are in the study area. The northern half of the study area and adjacent lands to the north, northeast, and east are or were recently under oil and gas lease, Basalt and latite-andesite of the Challis Volcanics predominate in the study area. Several hundred feet east of the study area is a quarry in talus of Mississippian-age limestone that was used for sized 100-pound rock fill in the Old Dry Creek Reservoir dam. Two samples, one taken at the quarry and the other at a limestone outcrop on East Fork Burnt Creek, have CaC03 content in the range of 90 to 95 percent, and is suitable as the limestone component of Portland cement, However, limestone outside the study area could supply foreseeable demand. Lead- silver mineralization has been observed in Paleozoic carbonate rocks elsewhere in the Lost River Range, but these rocks do not occur in the study area.

Jan 1, 1986

By Richard A. Winters

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 49,875 acres of the 54,833-acre Big Jacks Creek Wilderness Study Area (ID-111-7C) in order to evaluate the mineral resources. The study area is located in Owyhee County, ID, about 15 miles southwest from Bruneau, ID. No mining districts are in the study area, but part of one placer claim, located in 1924, extended into it. The northern portion of the area was covered by oil and gas lease applications; all were cancelled prior to 1985. No economic concentrations of minerals were found in the study area. INTRODUCTION This report describes the USBM (U.S. Bureau of Mines) portion of a cooperative study with the USGS (U.S. Geological Survey) to evaluate mineral resources and potential of the Big Jacks Creek study area at the request of the BLM (U.S. Bureau of Land Management). The USBM examines individual mines, prospects, claims, and mineralized zones, and evaluates identified mineral and energy resources. The USGS evaluates potential for undiscovered resources based on areal geological, geochemical, and geophysical surveys. Results of the investigations will be used to help determine the suitability of the study area for inclusion into the National Wilderness Preservation System. Although the immediate goal of this and other USBM mineral surveys is to provide data for the President, Congress, government agencies, and the public for land-use decisions, the long-term objective is to ensure the Nation has an adequate and dependable supply of minerals at a reasonable cost.

Jan 1, 1986

By Christopher J. Bise

PRINCIPLES OF MINE PLANNING During the initial planning stages, all mining operations are analyzed and evaluated in a similar fashion. This similarity holds true because the mine-planning procedure can be reduced to a network of interrelated systems that are tied together by a common philosophy of mine planning: namely, that the resource is to be extracted in a manner which is safe, efficient, and profitable. The success of the mining operation cannot be guaranteed unless each of these three requirements is met. Fig. 1 shows a flowchart for the initial planning of any mining operation. Notice that there is a preplanning stage that leads to the planning of four interrelated systems. The preplanning stage includes property exploration, estimation of production and manpower requirements, and the establishment of construction timetables. The four systems, evaluated after the pre-planning stage, are broken down into the following: (1) Excavation and handling system, (2) Strata control system, (3) Operating support system, and (4) Service support system. The Excavation and handling system includes the selection of all the equipment for the removal of the resource from its in-place deposit (e.g., draglines, continuous miners, rock drills, etc.) and for the transportation of the mined material from the face (e.g., belt conveyors, trucks, etc.). The Strata control system incorporates all those considerations which maintain the integrity of the roof, ribs, floor, and overburden both during and after the extraction phase; typical considerations in this area include pillar sizing, artificial support of the immediate roof in mine entries, and subsidence protection. The Operating support system contains the "necessary evils" of mine planning; the system consumes a large percentage of the mining engineer's planning time but does not contribute to the actual extraction of the resource. However, if proper attention is not paid to the various components of the system, such as ventilation, drainage, and power, then the mining operation will not perform to its capabilities. Finally, the Service support system is composed of those operations which keep the mine running efficiently; typical examples of these include maintenance and sup- ply. One important concept that Fig. 1 is designed to emphasize is that the four systems are interrelated; typically, a slight alteration of one can affect the performance of another. If these interrelationships are ignored, the effects on the system can be disastrous. The mine preplanning stage and the four subsequent system evaluations constitute the Analysis portion of the mine planning flowchart. After this portion of the study is completed, the overall projected operation can be evaluated by techniques such as financial analysis. This last step in the study is referred to as the Synthesis of the previously calculated parameters into an overall plan. Much has been written about the overall evaluation of mining properties, but, over the past thirty years, very little has been written about the analysis of mine- planning systems in a coordinated manner. Further, those texts which attempted this topic have failed to give sufficient examples for successful implementation, thus supporting the operating engineers' lament that it is easy to discuss theories but difficult to show applications. This text is intended to bridge this gap. Examples of the various stages of the analysis portion of the mine planning flowchart shown in Fig. 1 will be covered in this text, with the exception of the Service support system, since this system is oriented more toward day-to-day planning than long-term mine planning. INTERNATIONAL STANDARDIZATION The benefits that can be derived from an international standardization of the units used in mining engineering calculations are numerous. The interchange- ability of equipment parts and the ability to analyze and compare performance and design specifications on an equal basis are just two of the goals desired by both manufacturers and mine operators. Unfortunately, conversion to an international standard has not been rapidly achieved by engineers in the United States, due to their training under the English system. The Society of Mining Engineers of AIME has made the commitment for the adoption of the Systeme International d'Unites (SI) in all mining engineering calculations. Since many practicing mining engineers and students in undergraduate programs still find difficulty in relating to SI units, the calculations in this textbook will use the English system, with Table 1 available for conversion into SI units.

Jan 1, 1986

By F. Touboul, M. Thiercelin, K. BenNaceur

Introduction The need to develop accurate predictive hydraulic fracturing simulators arises from the consideration of vertical containment for the fracture. Fracture height growth from a pay zone into adjacent layers has been shown (see Cleary [I]) to depend on three sets of parameters for the different strata: - elastic properties, - closure stress variations, and, -fracturing fluid leak off, and poro-elastic stresses. Qualitative analysis of the effects of these parameters has been reported in the literature. The first effects were described by Van Eekelen, using simple elasticity considerations [2]. The effect of stress variations was described numerically by Simonson and a1. [3] and experimentally by Thiercelin [4]. Effects of back stresses induced by fluid invasion on fracture propagation were considered by Cleary [5]. In order to couple these effects, a numerical code al- lowing the simulation of three dimensional growth of a hydraulically induced fracture has been developed with the ability of representing the effects of heterogeneities on fracture lateral and vertical extension. The model is based on a new variational formulation of the boundary integral representation of three-dimensional elasticity. The fluid flow and elasticity equations are solved using a moving mesh representation which offers enough flexibility to enable the simulation of any closure stress distribution. Simpler models representing fracture height growth (P3DH models) have been developed [6] [7] that approximate the fracture by a series of one dimensional segments, and the limitation of such approaches is examined in this paper. 1 Description of the model 1.1 Fracture Geometry Hydraulic fracturing simulations involve the coupling of solutions to elastic deformations, fluid flow in the fracture, and fluid leak off into the formation. Since the use of direct solution techniques (i,e,,3D finite elements) is prohibitive, the method used in this study is baaed on a boundary integral representation of the 3D elasticity equations. 1.2 3D Models The classical representation of the problem of a fracture in an infinite medium by boundary integrals is [8]: [ ] where u is the unknown displacement field, r n is the traction operator, I? is the fracture surface, and K is the Kelvin tensor of fundamental solutions to the elasticity operator. Using the notation: [ ] for the displacement discontinuity (or fracture width), one can attempt to solve the boundary integral relation using surface integrals (91 or the displacement discontinuity technique, first introduced by Crouch [lo], and extended to three-dimensional problems [Ill. However, numerical problems arise since the Kelvin tensor has a singularity in

Jan 1, 1986

By Fabjanczyk MW, Aziz NI, Hii J

The paper presents the results of a series of pull out tests performed on roof reinforcement systems currently being adopted in mines in Australia 7mm wire, dividag bar, 15.2mm strand cable, and birdcage cable. The study also investigated the load deformation chara- cteristics and the various design parameters controlling the effectiveness of a cable-grout system. Suggestions for continued work are Highlighted.

Jan 1, 1986

By Joseph F. Shirley

Introduction Inorganic depressants are chemicals added to the froth flotation process to maintain or produce hydrophylic surfaces on one or more minerals so they will remain in the pulp rather than attach to the air bubbles. Whether a depressant will be effective in depressing a given mineral depends on how it is used and the environment in which it is used. Some depressants must be added and conditioned into the pulp before the collector is added. Other depressants can be added in the presence of previously added collectors and effectively depress the desired minerals. Often the concentration of depressant relative to the collector concentration is critical to making an economic separation. It should be noted that some depressants will only work when specific collectors have been used. Some reagents such as sulfuric acid and hydrogen peroxide essentially act as depressants by altering the previously added collectors so that they are no longer effective. Some depressants such as sodium ferrocyanide are only effective in a very limited pH range and an essentially collector free environment. Major Depressants CaO Milk of Lime is by far the most used depressant both in tonnage and dollar value. Although it is most commonly listed as a pH modifier, it is also an important depressant for pyrite in copper and copper molybdenite flotation plants. Although a simple pH adjustment will often depress pyrite, there are times when grinding with fresh milk of lime is required to obtain optimum depression. Lime is also a molybdenite and gold depressant. NaSH Sodium hydrosulfide is by far the most commonly used reagent to depress copper and iron sulfide minerals in by-product molybdenite flotation plants. NaSH also depresses gold, silver sulfides and silver chloride. ZnSO4 Zinc sulfate is commonly used to depress sphalerite in lead-zinc and copper-lead- zinc flotation plants. It has also been used to effectively depress talc in by-product molybdenite circuits at a pH of 6.5.

Jan 1, 1986

By S. C. Sethi

The WIPP (Waste Isolation Pilot Plant) Project near Carlsbad, New Mexico, is a research and development project sponsored by U.S. Department of Energy, designed to demonstrate the safe containment for disposal of radioactive waste. A mine (repository) is currently being developed 2150 feet below the surface, in a thick salt bed which will serve as the disposal medium. Provision of a proper ventilation system at the WIPP Project is a major priority of those responsible for its design, management, and operations. As an ongoing effort towards this goal, it was decided to simulate the mine's ventilation system using Dravo's MINEVENT computer program. Specifically, the work included the development of the following simulation models: 1. Simulation of the current ventilation system 2. Simulation of the designed ventilation system for the following modes: o Mine Construction mode/shift o Waste storage mode/shift o Fire or exhaust filtration mode These computer models are useful in solving complex ventilation problems likely to be encountered in an R&D project, like WIPP. They are particularly helpful for the development of contingency plans to incorporate during emergency situations, such as fires, fan stop- pages, radiation leaks, etc. Also, they can be utilized when considering expanding certain underground areas to ensure the availability of adequate ventilation.

Jan 1, 1986

This case study reviews the Charters Towers vein systems for potential open-pittable bulk tonnage resources in' stockworks, horsetails or multiple vein systems. The review summarises district evaluation undertaken over the last 18. months before specific drill evaluations.Historical mining from Charters Towers includes in excess of six million ounces at head grades of one ounce per ton. A review and structural studies show most veins as simple, tight systems without significant horsetails or multiple sheeted systems. In addition the normal gold content of the pyritic selvages ('formation') is low and disseminated gold is virtually absent. Shoots are structurally controlled on vein/vein and vein/contact intersections. Historically high production vein systems are hosted by .,.t o of the younger granodiorite phases.Geometrically most veins dip shallowly (from 45¦ to as low as 200) in a north or easterly quadrant. Flat dips permit open cut exposure of considerable vein area at a favourable stripping ratio.

Jan 1, 1986

By Andrew M. Leszcykowski

In 1984, personnel from the U.S. Bureau of Mines examined 41,550 acres of the North Fork Owyhee River Wilderness Study Area for mineral resources. This study area, in southwestern Idaho, is underlain by tuffs and basalt of Tertiary age. There are no known mines, claims, or prospects in or near the area. The northeast and southwest corners of the area are covered by oil and gas leases or lease applications, but no known exploration has been conducted. On Nickel Creek and Pleasant Valley Tables, in the southern part of the area, thin flows of vesicular, moss-covered basalt occur that are suitable for use as decorative building stone. The stone available for exploitation crops out over several square miles. However, more suitable material, outside the study area, is closer to potential markets.

Jan 1, 1986

By Richard D. Lang

Introduction Argyle is located in the Kimberley region in northwest Australia (Fig. 1). It is a significant diamond discovery by world standards and is the first major diamond find in Australia. The deposit consists of a pipe and associated alluvial deposits. Before the 1970s, diamonds were known to exist only sporadically in Australia. They have been found occasionally in association with gold deposits in Western Australia. There is a small deposit near Copeton in New South Wales. Some alluvial occurrences have also been found in Victoria, South Australia, and New South Wales. The first indicator minerals in the Kimberley region of Western Australia were discovered in January 1973. Production from the alluvial deposits at Argyle began in 1983. A $430-million construction program to develop a mine and treatment plant capable of producing 25 million carats per year was completed in December (1 carat = 0.2 grams). Ownership and management Participants in the project are known as the Argyle Diamond Mines Joint Venture. The group consists of CRA Ltd., 56.8%; Ashton Mining Ltd., 38.2%; and the Western Australian Diamond Trust (formerly Northern Mining Corp.), 5%. The project is managed by Argyle Diamond Mines Pty. Ltd., a wholly-owned subsidiary of CRA. Marketing is undertaken separately by the Western Australian Diamond Trust and by Argyle Diamond Sales Ltd. (for CRA and Ashton Mining groups). History Ownership of the Exploration Joint Venture has changed over the last 12 years as various parties changed their shareholdings. The original Kalumburu Joint Venture was formed in 1972 with five participants, each holding a 20% interest. By 1983, a number of ownership changes had occurred. The end result is that two original participants have sold out. CRA now holds a 56.8% share and the Ashton Mining Group holds 38.2%. CRA also assumed project management in January 1977. Table 1 demonstrates the long lead times involved in developing a project.

Jan 1, 1986

By Hardy J. Smith

The rock mass parameters which need be evaluated to estimate the rippability of rock are briefly outlined and their significance is discussed. Several methods used for estimating rippability are compared, and the advantages of taking into account a wide spectrum of rock mass parameters are emphasized. A systematic means of numerically weighing six rock mass parameters to produce a Rippability Rating (RR) is recommended, and a method of correlating this rating with the refraction seismograph method and with tractor horsepower is shown. Although the overall method demonstrated is systematic and yields specific numerical results, an integrated approach is recommended to its application, taking into account: the Rippability Rating; seismic velocity and geologic material; and other engineering judgment factors.

Jan 1, 1986

By W. Z. Choi

A model describing size reduction and mineral liberation during grinding has been extended to include multiple classes of composite particles. The majority of the model parameters have been directly determined using computerized image processing equipment to analyze the products from batch grinding tests. A coarse-grained sphalerite ore from Tennessee, representing a nearly ideal binary mixture of sphalerite and dolomite, has been used to experimentally validate the model for the case of dry, batch grinding. In all cases, excellent agreement has been observed between the model predictions and the experimental results.

Jan 1, 1986

By W. W. Roepke, B. D. Hanson

A major problem facing the coal mining industry today is the need to meet more stringent dust standards due to quartz. When secondary suppress ion is not adequate, the time-consuming and costly cut-and-try method of modifying the mining machine is used in the hope that it will reduce dust generation. The Coal Cutting Technology Group, at the Bureau of Mines' Twin Cities Research Center, has developed an inter-active computer program for drum- type cutting systems to help identify, in advance, modifications that offer the best potential for reducing dust. The program, Relative Dustiness Indicator (REDI), evaluates machine dimensions, seam characteristics, and operator-controllable variables for dust generaton, energy, forces, and product ion.

Jan 1, 1986

In 1985 BMR assessed Australia's economic demonstrated resources of mineral sands as follows: rutile 8.0 Mt, ilmenite 41.4 Mt, zircon 11.5 Mt, and monazite 229 000 tonnes. These resources are located along the east coast of Australia, in the southwest corner of Western Australia, and in the Eneabba region, north of Perth, WA. However, over 40% of Australia's rutile and zircon resources, particularly those on the east coast, are presently not available for mining because of environmental considerations. As well, east coast ilmenite has been considered unsuitable for use by sulphate route pigment producers because of its relatively high chrome content. World demonstrated resources of rutile and zircon are estimated by BMR as 29 Mt and 38 Mt respectively. Demonstrated resources of ilmenite amount to about 1 billion tonnes. These occur predominantly in hard rock deposits in Norway, Canada, USSR and China, as well as alluvial deposits in Australia, South Africa and India. Quantitative data for world monazite resources is sparse. However, world production of rare earth oxides is now mainly from bastnaesite, a hard rock resource. Australia is presently the world's principal producer of rutile and zircon, and also provides a major share of the world's ilmenite. With the expected increase in Australia's rate of output of these commodities, combined with restrictions on mining along parts of the east coast, its position could diminish substantially over the next 25 years.

Jan 1, 1986

By William J. Gregg

Mechanical testing results on oriented Devonian gas shale core throughout the Appalachian basin show a preferred fracture direction perpendicular to bedding. The preferred direction is generally parallel to the Allegheny Front, but is only coincidentally parallel with in-situ stresses in some areas of the basin. The strength of the preferred orientation of induced fractures decreases with distance from the Front. It is suggested that strain related to Paleozoic deformation is responsible for this mechanical fabric and thus the direction of induced fractures in laboratory tests may not be of use as indicators of in-situ stress orientations as previously suggested.

Jan 1, 1986

By M. Ghoreychi, M. Fauueau, P. Lebitou, P. Berest

A brief study of the history of gas caverns in salt formations enables us to consider creep mechanism in a cavity as a phenomenon of dissymmetrical deformation. Among different parameters affecting such a phenomenon, gravity forces, especially in large caverns, seem to be responsible for important bottom heaves as compared to roof releases. This fact is demonstrated here by means of certain theoretical considerations concerning elasto-viscoplastic constitutive laws relevant to rocksalt rheological behavior.

Jan 1, 1986

By B. K. Parekh, W. M. Goldberger

Silicon carbide (Sic), produced by heating rice hulls to elevated temperatures, contains a mixture of beta crystalline silicon carbide whiskers, particles, and unreacted carbon. The silicon carbide whiskers are 0.5 micron in diameter and 50 to 100 microns in length and have been found useful for reinforcing metal and other composite materials. The carbon can be removed by combustion, but this makes separation of the silicon carbide whiskers from particles difficult and a high grade whisker product cannot be made. However, a clean, high grade SiC whisker product can be obtained from the pre-burned converted rice hulls using physical separation processes that are based on differential wetting. Recovery of Sic whiskers from the pre-burned material was found to exceed 90%. A modification of the froth flotation process developed during this study is now being used commercially to separate silicon carbide whiskers and particles and to recover a high grade whisker product.

Jan 1, 1986

By H. L. O. Huyck

A microcomputer equipped with spreadsheet, data management, and FOR- TRAN programming software is used to update and quantify a model for ranking seventeen economically important metal commodities in terms of market potential (Huyck, 1982). Weighted factors are used for the ranking: (1) demand growth trends, (2) end-use substitution vulnerability, (3) recycling trends, (4) price trends, and (5) cumulative demand versus world reserves factor. Price trends are defined using (1) price-vs.-year slopes (with prices in 1967 constant dollars) and (2) standard deviations of slopes (to indicate price volatility). Substitution vulnerability is defined as the percent of end-use which is replace- able by other commodities, and a factor indicating the likelihood of such substitution. Factors are normalized and linearly combined to produce a ranking of the seventeen metals. Microcomputer software is essential for organizing data and calculating statistical parameters and linear combinations of factors.

Jan 1, 1986

Coal slurry pumping was introduced into the U.K. in 1973. Gateside packs were prepared in areas of containment using R.O.M. coal and a special fast setting cement. The packs restricted roadway convergence and moderated spontaneous combustion risks, but costs were high and alternptives were sought. A similar system using OPC and an accelerator had limited success. Much more successful was the Aquapack process which used dilute slurries of a special OPC based cement and an accelerator based on sodium carbonate and bentonite pumped simultaneously into la fabric packbag. The Tekpak system using HAC and a much modified calcium sulphate mixture superceded Aquapack on the grounds of improved cement pumping life lower alkalinity and lower costs. A further modification of this system gave a cement with a 24 hour pumping life thus obviating flushing out pipe ranges except at the week-ends, improved packbags also increased the efficiency of the process. The hazard of spontaneous combustion can be inhibited if air supply channels across the waste can be located and plugged. Using gas samples from pack pipes to locate the heating and injecting a special grout, formulated from bentonite, sodium silicate and thixotroping agents. into the waste on the intake road has proved a successful method of controlling heatings. Mine' roadway and face cavities are being safely and successfully filled with cementitious foams produced in a novel placer machine. The foams are based on fast setting cements with specialised foaming agents. Up to 13 cu. metres per hour of fast setting thixotropic foams can be produced and their use is now widespread throughout U.K. coal mines.

Jan 1, 1986

By Laxman S. Sundae

The Bureau of Mines designed, fabricated, and is using an in-seam tester (1ST) for in situ determination of coal cutting forces. This re-port describes the results of field tests conducted in the Pocahontas No. 3 and Upper Freeport seams to obtain peak and mean cutting forces during coal cutting with several bit geometries, including radial and point attack bits currently used on drum-type machines. Comparisons were also made between new and worn bits, and using data obtained from a Bureau-modified chisel bit. The test results show that longwall plough cutting (horizontal cuts) in bony coal bands (shale) requires >3 times the cutting force for the same cuts in a vertical direction. When no bony coal is present, the cutting forces required to make horizontal and vertical cuts are equal. Worn bits require 4 to 5 times more cutting and normal force than new or undamaged bits. Normal force increased drastically for the worn chisel bit. Peak force encountered in making independent cuts was found to be ~3 times higher than that required to make interactive cuts using a spacing-to-depth-of-cut ratio of 2. Both rake and clearance angles were found to have a significant effect on normal and cutting force.

Jan 1, 1986