Search Documents

By Matthew J. Hrebar

Dragline stripping operations account for over one-half of the U.S. bituminous coal production mined by surface coal mining methods. The dragline is a popular stripping tool because of its flexibility in varying overburden depths and relatively low operating costs per cubic yard of overburden. Because of the relatively high capital costs of the machines and their use as a primary stripping tool, the selection process is an important step in the mine planning procedure.

Jan 1, 1979

By L. Whitby-Costescu

The Shebandowan mine and concentrator, with a capacity of 9072 t/week (10,000 st per week), was opened in 1972 after several years of environmental study and planning. The mine is located in a popular vacation cottage .area about 96 km (60 miles) west of Thunder Bay, Ontario. Undertaken before environmental assessment procedures had become an established requirement, Shebandowan is one of the first Canadian examples of effectively integrating environmental work into overall planning. Although it is an underground mine, many of the environmental considerations are common to open-pit operations, and hence, it provides a case history for the use of all mine planners. Computers can play a part in such studies by simulating the annual production of mine wastes, by on-line polling of environmental sensors and by processing sensor data. Early attention was focused on establishing base-line conditions in a two-year water quality monitoring program. Since production began, water quality monitoring has shown that mining has not caused any significant changes. However, mine drainage disposal arrangements had to be modified in the light of operating experience. There is no townsite associated with the mine, and workers commute from established municipalities. Harmonious relations have been achieved with local cottage residents after their initial fears were dispelled. Plans are ready to begin revegetating the tailings when a sufficient area of dry elevated tailings has been accumulated. Rehabilitation of the land disturbed during development was begun before start-up and was completed during initial operations.

Jan 1, 1979

Fines and unnecessarily small rock fragments are created by as many as four identifiable breakage mechanisms which operate close to the charged section or sections of the blasthole. The peak blasthole pressure (Pb) should not exceed that value at which the rock starts to fail in compression. Excessive Pb values can be prevented by carefully selecting:1. the composition, density and/or diameter of the charge, and2. the initiation/priming system.The percentage of fines increases with:1. increases in the charge diameter:blasthole diameter ratio, burden distance, blasthole diameter, effective sub-drilling and size of blast, and2. decreases in blasthole spacing, stemming height and the length:width ratio of the blast block.Decked charges tend to reduce the percentage of fines.Excessive fragmentation is more evident in buffer blasting and sinking cut shots than in blasts fired to a clean free face. Initiation sequences which give effective burdens considerably less than drilled burdens encourage the minimization of fines, as does an inter-row delay time which promotes good progressive relief of burden.The wastage of explosive energy in creating fines is most pronounced where fully-coupled, energetic charges are fired in weak and/or highly porous rocks. This is especially so where forward movement of the strata is impeded by buffer rock, excessive burden distances and/or inadequate inter-row delay times.

Jan 1, 1979

By David J. Raden

INTRODUCTION Economic deposits of phosphate are found at shallow depths (80 ft.) in central and northern Florida (Figure 1) where they have been mined since the late19th century(l).The present (1978) mining rate is approximately 40 million short tons per year of product (called “phosphate rock1”), which represents approximately 80% of the total U.S. production and 30% of the world production. The principal use of Florida phosphate is for the manufacture of fertilizer. There are 10 major mining companies and 20 active mines in Florida at the present time, strip mining approximately 5000 acres per year. The ore, known as "matrix," consists of gravelly clayey sands containing phosphate minerals (principally carbonate fluorapatite), quartz, and clay minerals. The clay to phosphate ratio is generally about 1:1 by weight and the sand to phosphate ratio ranges from, 1:1 to about 3:1. Mining is done by large electric draglines, which strip and cast the sandy overburden soils, generally 10 to 40 feet deep, and remove the matrix, generally 10 to 25 feet deep. Dragline bucket capacities are generally 20 to 45 cubic yards, but range up to 65 cubic yards. Mining cuts are usually 300 to 500 feet wide and up to several thousand feet long. The ore is cast into an earthen sump where high pressure water guns are used to slurrify it. Centrifugal pumps move the slurry through a pipeline to a beneficiation plant where the phosphate rock is separated from the waste sand and clays.

Jan 1, 1979

By John S. Jones, Ralph E. Brown

INTRODUCTION For more than a century, artificial ground freezing has been used for groundwater control and structural support for excavations. Most of the early uses of the freezing method were for sinking deep access shafts for mines and tunnels (1,2,3,4). More recently, ground freezing has increasingly been used for construction of large diameter cofferdams and soft-ground and mixed-face tunnels (5). Although ground freezing has been used in the past-for tunnels, it was invariably used as a last resort measure, where more conventional measures could not be used. The more recent freezing applications, however, have become increasingly cost competitive with more conventional techniques, and are now being included as part of the design concept (6,7,8,9,10,11,12). The purpose of this paper is to describe some of the more recent applications of ground freezing for tunnel construction. The paper begins with a brief description of the most commonly used freezing system, the Poetsch process. Recent tunneling projects utilizing ground freezing for structural support are then discussed. DESCRIPTION OF THE FREEZING METHOD The most commonly used freezing method is the Poetsch process, which was originally developed by F. H. Poetsch in the late 1800's. The system consists of a brine coolant, typically calcium chloride and water. Freezepipes are placed into boreholes or are

Jan 1, 1979

By Bengt L. Stillborg

INTRODUCTION This paper summarizes the result of a two and a half year research program. The objective of the research was to develop a fundamental understanding of the Rib-in-Roc method. Through the development of a new model technology, namely three-dimensional physical models which powerfully exploit the results of dimensional analysis Stillborg, Stephansson and Swan (1), it has been possible to establish the contribution to both permanent and immediate stabilization of a large underground opening pre-reinforced by the Rib-in-Roc method. Using the results from these physical models and earlier work by Stillborg and Stephansson (2) and Åkesson (3), a conceptual synthesis is given in this paper so demonstrating the Rib-in-Roc method to be a practical working system of pre-reinforcement. DESCRIPTION OF THE RIB-IN-ROC METHOD To give the reader an idea of how this method of pre-reinforcement is performed, a short description will be given, Figure 1. Before any full-scale excavation takes place an entry is made in the host rock and rib raises are driven around the proposed opening. These raises are made at a spacing that is dependent upon rock quality; an opening in poor rock needs more ribs per length of opening. As the ribs are driven they are used as a site from which very competent rock bolting can be done. As a rib is excavated it is filled with reinforced concrete. Finally after having in this way reinforced the zone around the proposed opening, (a reinforced arch is formed) the displacements are automatically controlled as the opening is being excavated. Using this method openings with a span of 50-60 meters (160-200 ft) and a height of 60-80 meters (200-260 ft) are likely to be realised.

Jan 1, 1979

By Charles G. Howard

Accidents involving underground rail transport were analyzed to quantify the magnitude and the operational requirements for individual mine car braking systems. The results showed that the brake preventable accidents represent only 2% of the total underground fatal accidents and less than 1% of the total underground nonfatal accidents. In addition, the brake preventable accidents are expected to decline over the next decade. The costs of accidents involving deaths and Injuries were determined using various well accepted methods. The costs of a brake retrofit program for all operating underground coal cars were developed separately for small and large coal mines. Costs of retrofit brakes, new car brakes, maintenance, inspection and repair facilities were included in the esimates. The analysis showed that a retrofit program would not significantly increase safety, and that the program cost would greatly exceed the corresponding expected benefits.

Jan 1, 1979

Toward the goal of maximizing minerals and metals recovery from domestic resources, the Bureau of Mines, U.S. Department of the Interior, has conducted in situ corrosion studies at the Salton Sea Known Geothermal Resources Area (KGRA) in the Imperial Valley, Calif., to evaluate and characterize materials of construction for geothermal resources recovery plants. General-, pitting, and crevice-corrosion characteristics of 13 commercially available alloys were investigated for periods of 15 and 30 days in seven process environments expected to be found in typical geothermal resources plants. Stainless steel alloy 29.4, Inconel 625, and the Hastelloys G, S, and C-276 were the most resistant to general corrosion, did not pit, and exhibited little susceptibility to crevice corrosion. Stainless steel alloys 430, E-Brite 26-1, and 6X had low general corrosion rates, but pitted and were susceptible to crevice corrosion. Stainless steel alloy 316 L had a low corrosion rate, but corroded intergranularly, pitted, and was susceptible to crevice corrosion and to stress-corrosion cracking. Titanium-1.5 nickel and TiCode-12 had low corrosion rates, did not pit, and were not susceptible to crevice corrosion. Carbon and 4130 steels had high corrosion rates, pitted, and had high susceptibilities to crevice corrosion. The major scale-forming mineral on the corrosion samples in most of the process environments studied was galena mixed with lesser amounts of other minerals.

Jan 1, 1979

By D. W. Niosi

In this chapter, a review is made of the various stages of an exploration program, mineral rights acquisition methods and the partners involved in an agreement, the after- tax cash flow approach using present value discounting principles, the establishment of computerized financial models for assistance during the negotiating stages for a mineral property, and the various evaluation techniques and their specific applications during different phases of an exploration program. A set of examples is shown encompassing the initial target-seeking stages to the ultimate feasibility study stage.

Jan 1, 1979

By R. Larry Davis

Over the past decade there has been a continual decrease in domestic oil reserves accompanied by a sharp increase in the demand for energy. Even with increased imports of foreign oil, the energy demand has not been met. This has forced many users to turn to substitute fuels. Of the many substitute fuels available most users are turning to and creating an increased demand for low sulfur coal. Because of the increased demand for low sulfur coal as well as the inherent problems in producing eastern coal, many producers have turned their attention to the large deposits of low sulfur coal in the western United States. Western coal mining is, however, not without its problems such as high moisture content, high ash content, highly variable sulfur content, multiple seams, and/or pitching seams. It is to aid in the solution of these problems that this chapter is directed.

Jan 1, 1979

Exploration of new resources and development of new equipment and designs are an ever changing facet of mining. New equipment to handle specialized operations is being developed and new techniques for its use explored. One such system is reviewed. Another is a potential system for handling the thinner stray coal seams between the more profitable thick seams. The availability of federal coal leases in the West is reviewed and current planning discussed. Gulf Coast lignites have been of much interest in recent months and are overviewed.

Jan 1, 1979

By P. T. Kane, O&apos

Capital and energy are the dominant cost factors in nickel production from laterites. Since the 1973 energy crisis, pyrometallurgical developments have been oriented towards lower cost sources of energy and higher grade ores and hydrometallurgy towards higher recoveries and greater flexibility in types of ores treated. Energy recuperation offers some potential, but at a price. 'The lower energy acid leaching process is indicated to have the greatest potential, particularly with its inherently high cobalt recovery.

Jan 1, 1979

By L. Keith Hudson

The purpose of this study is to provide data that demonstrates that the Alcoa flash calciner design can be used for the decomposition of AlCl3?6H2O to A1203. Heat and material valance data for calcination provides data on the partial pressure of HCl in the off-gases. Experimentally determined data for the HCl partial pressure, over solutions expected in producing alumina from clay by the hydrochloric acid process, show that HCl can be absorbed from the off-gases into process solutions to effect crystallization of AlCl3?6H2O.

Jan 1, 1979

By William E. Stanley

The paper examines the problems that arise in undertaking socio-economic impact studies to meet the requirements of environmental-impact legislation governing new mine development or expansion. An approach to undertaking socioeconomic impact studies is outlined, responses to specific problems are discussed and ways in which the mining company can use these studies to meet its general objectives are explored. The paper concludes by examining how a socio-economic study, as required by legislation, can be used to assist the mining company in achieving some general objectives it will have in developing a mine.

Jan 1, 1979

By J. K. E. Douglas

Brigadier Ralph Shelton Griffin Stokes D.S.O., C.B.E., M.C., who died in England on 24th February, 1979, at the age of 96 years, was one of the most colourful personalities in South African mining history. After the South African War, in which he served as a trooper, he joined the Crown Reef Mine as an assistant assayer (1902), and was to serve the mines of the Corner House Group intermittently for the next 57 years until his retirement in 1959.

Jan 1, 1979

By Lawrence L. Davis

This paper describes current research by the Bureau of Mines to develop technology for improving efficiency and productivity in metal/ nonmetal mines. The research program addresses a wide variety of problems associated with each of the major categories of mining: underground mining, surface mining, in situ mining, and premining investigations. An overview of the Bureau's research activities is given with emphasis on underground mining. In particular, two innovative and promising concepts currently under development are described: a unique shaft sinking system that uses an impact hammer for rock fragmentation, and a low-profile, portable crusher for underground hard-rock applications.

Jan 1, 1979

By Stanley D. Michaelson

Stanley D. Michaelson retired in 1976 as chief engineer, Metal Mining Div. and director of the Engineering Center for Kennecott Copper Corp. An active consultant on mining and metallurgical assignments, Mr. Michaelson is also currently adjunct professor of mining engineering at the University of Utah. He received his B.S. degree in mining engineering from Lehigh University in 1934 and an honorary E.M. degree from the Montana School of Mines in 1961. Mr. Michaelson received AIME's Robert H. Richards Award in 1962 and was named a Distinguished Member of the Society of Mining Engineers of AIME in 1975. He has served as a Director and as a Vice-President on the AIME Board of Directors and is a Past President of the Society of Mining Engineers. He became an Honorary Member of AIME in 1978.

Jan 1, 1979

By F. L. Wilke

A model is presented to minimize the winning costs per shift within the different sections of a potassium mine by liner programming and to simulate the other areas to get all costs in order to comp re different production strategies. he model is based on a a given total layout of the underground mining which is considered to be fix during the planning period. Room-and-pillar mining is assumed to be used. Potassium extraction is done by drilling and blasting. Transportation of the raw material to sectional crushers is done by scoop-trams where it is crushed to coarse-grains which allow further transportation by conveyor belts to the hoisting shaft or to a bunker. When production is stopped, the continuously working factory is supplied by means of this bunker. Starting from a desired composition of the raw material the model has to keep the given total. demand of raw material per shift, to minimize the winning costs, to keep the capacity constraints of the equipment and to determine the planned output of production of the sections per shift. Costs of the areas which follow the extractions are added to extraction costs in order to allow a comparision of costs of several alternatives of production. Optimization in extraction and assignment of scoop-trams to sections is done by linear programming. The other areas of the mine are treated by simulation. The model output is a schedule of the calculated costs broken down into costs of processes, equipment, and kinds of costs. This proceeding enables to compare different ways of production.

Jan 1, 1979

Indigenous brown coals, which provide a readily available primary energy source, have played a significant part in the industrial development of Victoria. The deposits located in the Latrobe Valley compare in extent with other major deposits of brown coal in the world. Smaller but valuable deposits occur at Stradbroke, Gelliondale, Anglesea and Bacchus Marsh. Extensive drilling, aided by geophysical surveys, and detailed analyses of coal samples, have enabled the extent and quality of these Tertiary deposits to be Defined.

Jan 1, 1979

By Colleen A. M. Gibbs

On July 30, 1979 New Council on Environmental Quality (CEQ) regulations for implementing the procedural provisions of the decade-old National Environmental Policy Act went into effect. These new regulations replace approximately seventy different sets of agency regulations, providing some uniformity throughout the Federal government in the conduct of environmental reviews and preparation of environmental impact statements (EIS). This attempt by the Federal government at a general improvement in the preparation and quality of EIS's presents an opportunity for the mining industry to evaluate how the EIS process for mining proposals can be expedited. The environmental impact statement is often a key element on the critical path of a major mining project. Preparation of the EIS is ordinarily the responsibility of the Federal agency with primary decision-making authority over the project. Still, the proponent, i.e. the mining company, can play a major role in the process and have a major impact on the timeliness and adequacy of the effort. Typically, the Proponent will conduct (or will hire consultants to conduct) environmental baseline studies of, for example, air quality, wildlife, geology, water quality, vegetation and archaeology. These studies are then compiled into an environmental report and submitted to the agency. The agency verifies the data and incorporates them into the environmental impact statement.

Jan 1, 1979