Search Documents

By E. J. Marcotte

"INTRODUCTIONThe Upper Canada Mine is located at Dobie, approximately ten miles east of Kirkland Lake, Ontario.The mill contains Upper Canada's cyanide circuit and Upper Beaver's flotation circuit. The combined capacity is 590 tons per day consisting of 415 t.p.d. of Upper Canada gold ore and 175 t.p.d. of Upper Beaver copper-gold ore.The Upper Beaver ore is trucked five miles to the Upper Canada mine site.Crushing:The crushing circuit consists of primary, secondary and tertiary crushing employing one C .A. C. 15 in. x 24 in. Superior jaw crusher, one 4 ft. x 8 ft. Tyler-Niagara double deck screen, one 3 ft. Symons standard cone crusher and one 3 ft. Symons shorthead cone crusher.The -2 in. product from the jaw crusher is fed to the double deck screen. The+ 5/ 8 in. passes over the top deck to the 3 ft. standard cone crusher; the+ 3/ 16 in. material passes over the lower deck to the shorthead cone crusher. The - 3 / 16 in. material pas sing through the lower deck of screens is the product to the mill.The screens used prior to the installation of rubber screen cloths were: one 4 ft. x 4 ft. section with 3/ 4 in. square openings and one 4 ft. x 4 ft. section with 5/ 8 in. square openings on the top deck; two 4 ft. x 4 ft. sections with openings of 3/16 in. x 4 1/2 in. slot on the lower deck. The fine screens were positioned so that the 4 1/ 2 in. slots were parallel to the flow of feed.The crushing circuit is operated on a three shift per day basis by one operator per shift."

Jan 1, 1968

By H. B. Charmbury

In the United States and in Pennsylvania in particular the coal mine drainage problem is of continuing and growing interest to the coal mining industry, the state government, the federal government and the public at large. The 1965 amendments to Pennsylvania's Clean Streams Law prohibit the discharge of acid mine drainage into the streams of the Commonwealth after January 1, 1967. Because of this new legislation, the coal mining industry and state government are extremely aware of the necessity for new techniques for treatment and prevention of the flow of acid mine drainage from the active mines of the Commonwealth in order to keep the coal mining industry in business in Pennsylvania. Approximately one-third of the total volume of mine drainage presently polluting the streams of the Commonwealth originates from "active" coal operations and two-thirds comes from "abandoned" mine discharges. As early as 1963 it became evident that the Commonwealth of Pennsylvania and the coal industry in Pennsylvania would have to take active steps to abate the mine drainage pollution of Pennsylvania's streams and rivers. This became quite clear during the deliberations in Harrisburg which climaxed a twenty year struggle for effective strip mining legislation. The bituminous strip mining law enacted that year made it unlawful to have any acid discharge from active stripping operations.

Jan 1, 1968

By Damon H. McFadden

5.1-1. Geographic and Geologic Factors. Surface mines are located where the coal seam can be economically uncovered and where the product can be utilized competitively with other fuels. The planning and designing of a pit may follow various procedures. The sequence for consideration of the influential factors as considered here may not be complete for every pit, nor will it be necessary to be completely used in each design. It is suggested as a check and outline for the engineering approach. Controlling conditions for the layout should be listed and considered with the facilities and equipment for the exploitation. After these items, as listed below, have been discussed and the feasibility agreed upon, then the actual planning and design of the pit can be done. GEOGRAPHIC FEATURES. The location of the coal area sets the climatic stage. The rainfall, the temperature extremes, and the general weather conditions all affect the design of the pit. Overburden soil when wet may not be stackable and may be impossible to move by standard procedures. The coal seam itself may be so soft that it must not be traveled on when wet, as the losses may be the difference between a profitable venture and an unsuccessful one. Some equipment will work well on dry soil only, just as a dredge works only in the wet. The conditions must be checked and analyzed. Some equipment cannot handle frozen soil (wheel excavators), so temperature extremes must be noted. The extreme weather conditions may also govern the expected working days and therefore the ultimate production. The altitude (atmospheric pressure) may affect the equipment, and this should be checked. All of these conditions should be noted on the preliminary map of the area. GEOLOGIC FACTORS. The geologic and surface conditions of the coal field dictate the type of pit generally feasible. Rough terrain, rolling terrain,

Jan 1, 1968

A quantitative chemical model of the rocks of the Broken Hill lode environment is presented to illustrate a stratiform orebody in a meaningful form to scientists interested in environmental control on the chemicalcomposition of sediments.Even though this study was restricted by the narrow range of rock analyses available it is obvious that significant chemical differences exist between the various rock units and also that some association of metallic sulphides with Ca, Mn, Fe, and P is indicated.Correlation of this evidence with that from other mining fields may point out more definite chemical relationships and elucidate the puzzle of the mode of formation of many stratiform orebodies.

Jan 1, 1968

By Neal P. Cochran

The Office of Coal Research Program has been outlined in our Annual Report for a number of years and reported on by various members of the OCR staff as well as by our contractors. The program is national in scope and is intended to develop new and improved uses for our Nation's coal resources and to maintain coal in a favorable economic position, vis-a-vis, the other energy forms. A program has been developed that includes conversion of coal to gas, gasoline and other petroleum-type products, and to electricity. These projects are only one facet of the OCR program albeit an important one. In many of the conversion projects we have underway, original development work has been done with bituminous and sub-bituminous coal. It is the intention of this paper to present a general outline as to how lignite might fit into one or more of these projects as a raw material. Our national lignite reserves are vast in scope and this has been recognized in the OCR program by development of a project specifically for lignite and by including lignite as a test raw material in many other projects. Project Lignite is intended to develop the Cop Acceptor Process for conversion of lignite to a high B.t.u. gas. In this effort we have included the design, construction, and operation of a lignite gasification plant at Rapid City, South Dakota. The work is being conducted by the Consolidation Coal Company and is an outgrowth of their laboratory development of this process. The first portion of our effort included a detailed economic study of a somewhat arbitrary grouping of States designated Market Area A that could be expected to use gas manufactured in a lignite gasification plant. The area included the Dakotas, Minnesota, Nebraska, and Iowa. This geographical area could readily be served if a process could be developed for converting North Dakota's lignite reserves, estimated at 351 billion tons, to high B.t.u. gas. Our study showed that Market Area A had a potential commercial- industrial market of one trillion cubic feet of gas a year. To meet this demand, we believe that part of the load can be obtained from commercial lignite-to-gas plants. At the time of our original study, we concluded that gas could be delivered to the city gate in Market Area A at about 45¢. As a result of price escalation in the interim, our estimate today might be slightly higher, but not significantly so, since some parts of the process appear better today than they did at the time of the original projection.

Jan 1, 1968

By R. F. Abernethy

A chemical method of determining microgram quantities of arsenic in coal was investigated by the Bureau of Mines to supplement a semiquantitative spectrographic method of determining arsenic in coal ash. In accordance with a method recommended by the International Organization for Standardization, 1-gram samples of coal are decomposed by wet oxidation with boiling sulfuric acid (H2S04) and nitric acid (HN03) to remove the organic matter. After heating to fumes of SO3 to remove HN03, the arsenic is separated as arsine by the action of zinc in H2S04 solution. The arsine is absorbed in dilute iodine solution in which the arsenic is determined colorimetrically by the molybdenum-blue reaction. Two modifications of the method for obtaining the arsenic in solution, in addition to the wet oxidation method, give satisfactory results. The modifications are (1) furnace ashing with MgO added to the coal, followed by treatment with H2S04, and (2) extraction of arsenic from the coal by dilute HNO3 without ashing. Float-and sink-tests show that arsenic is associated mainly with mineral matter in the three coals examined. High-temperature ashing tests show that very little arsenic is volatilized from coal ash below 1,000° C, but it is virtually all removed from the ash at 1,300° C.

Jan 1, 1968

By T. F. Kassner

The dissolution kinetics of type 304 stainless steel in the Bi-Sn eutectic alloy have been investigated under the well-defined hydrodynamic conditions produced by the rotating-disc sample geometry. In addition, the mutual solubilities of iron, chromium, nickel, and manganese from 304 stainless steel in the eutectic alloy were determined over the temperature range 450" to 985°C. The convective -diffusion model for mass transport from a rotating disc was used to interpret the experinlental dissolution data. The dissolution process was found to be liquid-diffusion-controlled under specific conditions of temperature and Reynolds number. Liquid penetration into the 304 stainless steel resulted in a reduction of the di,ffusion-controlled mass flux and thus precluded the calculation of the diffusion coeficients of the four components from 304 stainless steel in the Bi-Sn eutectic alloy. The convective-diffusion model for diffusional limitations of electrode reactions and mass transport at the tationssurface of a rotating disc set forth by Levich 1,2 has found wide applicability in the investigation of electrochemical and dissolution phenomena in aqueous systems. Riddiford 3 and Rosner have reviewed the model and also include numerous references on work of this nature. More recently the rotating-disc system has been applied to the investigation of hetereogeneous reactions in liquid-metal systems. Shurygin and Kryuk 5 have measured the dissolution rates of carbon discs in molten Fe-C, Fe-Si, Fe-P, and Fe-Ni alloys. Shurygin and shantarin6 also studied the dissolution kinetics of iron, molybdenum, chromium, and tungsten, and the carbides of chromium and tungsten in Fe-C solutions with a rotating-disc sample geometry. In these systems it was possible to distinguish between diffusion and reaction control mainly through experimental confirmation of the velocity dependence of the dissolution rate predicted by the model. However in the absence of dependable solubility data and the virtual lack of diffusion data in these systems, a quantitative check of the magnitude and the temperature dependence of the rate was not possible. In many instances, estimates of the activation energy for solute diffusion and the diffusion coefficient based upon the experimental dissolution data are not credible. A recent study by this author7 has resulted in a critical test of the model in a liquid-metal system. The solution rates of tantalum discs in liquid tin were measured over a wide range of temperature and velocity conditions. In addition, the solubility and diffusion coefficient of tantalum in liquid tin were determined as a function of temperature. The latter data were used with the model to predict both the magnitude and the temperature dependence of the dissolution flux. In that work it was also deemed necessary to reevaluate the solution to the convective diffusion equation to incorporate the effect of the lower range of Schmidt numbers encountered in liquid-metal systems. Good agreement between the model and the experimental dissolution data in the region of diffusion control was obtained in the Ta-Sn system. The Bi-Sn eutectic alloy is used as a seal between the reactor head and the reactor vessel in the Experimental Breeder Reactor-11. The alloy is fused periodically prior to fuel-handling operations. In that connection, it was necessary to investigate the compatibility of the liquid alloy with the type 304 stainless-steel containment material. The results of a rotating-disc study in this multicomponent system are presented. EXPERIMENTAL METHOD The 5.08-cm-diam discs were machined from 0.317-cm-thick plate. Chemical analysis information for the type 304 SS material is given in Table I. The discs were ground flat on metallographic paper and given a final polish on Linde B abrasive. A thin support rod was threaded into the disc and the region around the threads was fused under an inert gas. The support rod was fitted with a quartz protection tube and then was attached to a supporting shaft which passed through a rotary push-pull vacuum seal. The disc and supporting shafts were dynamically balanced prior to insertion into the furnace tube. The apparatus is shown schematically in Fig. 1. The 58 pct Bi-42 pct Sn eutectic alloy melts were prepared from 99.995 pct pure Bi and Sn by fusing the components in a 7-cm-ID Pyrex crucible. The system in which the melts were made was evacuated to a pressure of 1 x 10-6 Torr and back-filled with purified argon several times before melting the charge. The ingot was reweighed and placed in a slightly larger-diameter Vycor crucible used in the dissolution runs. A run was started by lowering the disc into the liquid

Jan 1, 1968

By Frank G. Horino

This report describes an instrument designed by the Bureau of Mines for quantitatively identifying texture of rock surfaces produced by grinding or extremely rough surfaces beyond the range of commercial surface measuring instruments. The transducer for the instrument is a linear variable differential transformer that converts mechanical motion caused by surface roughness, waviness, and lay to an electrical output. The electrical output is recorded graphically as an X-Y plot of the line traversed on the rock surface. Details of the synthesized device and its calibration are given. The sensitivity of the unit is 2 percent of the scale setting of the amplifier. The horizontal scale is adaptable from ¼ inch to 15 inches of specimen length with a sensitivity of 0.01 inch if a 10 to 1 magnification is used and 0.1 inch if a 1 to 1 magnification is used.

Jan 1, 1968

By L. C. Brown, E. B. Hawbolt

The formation of grain boundary precipitates has been studied in Ag-5.64 wt pcl Al alloys at 688°C. Large-grain specinzerzs were used and the boundary misorientation measured by X-ray diffraction. At low-angle grain boundrrries Primary sideplates form. u)hile abore a 17-deg misorientation lenticular precipitates predominate. Growth of the lenticular precipitates was studied on individual grain boundaries using a statistical technique. The thickening and lengthening rates appeared to be independent of &apos;pain boundary misorientation, indicating that grain boundary diffusion was not significant in this system. The precipitates grew urith constant shape, with both the length and thickness increasing parabolically with time. The parabolic lengthening rates were unexpected since previous theory and experimerztal results had indicated linear growth. By approximating the shape of the precipitate to that of an oblate spheroid grouling with constant shape an equivalent diffusion coefficienl was calculated. The zlalue obtained was in good agreement with nleasurements obtained fron, diffusiorz couples. IF a single-phase alloy is heated or cooled to a temperature such that the phase becomes supersaturated, there is a tendency for a second phase to precipitate from it in order to remove the supersaturation. Precipitation takes place initially on grain boundaries due to preferred heterogeneous nucleation, but subsequently Widmans kitten plates may form in the grain interiors if the grain size and supersaturation are sufficient. The type of grain boundary precipitate formed depends on the nature of the boundary. Aaronson1 and clark2 have shown that grain boundary misorientation can be characterized by the simple parameter R, where and X, Y, and Z represent the minimum rotations about three orthogonal axes required to bring the two lattices forming the grain boundary into coincidence. The maximum value for R is 60 deg. In using this parameter the orientation of the grain boundary itself is, of course, neglected. However it was found in both Fe-si3 and A1-Ag2 that the precipitate shape depended only on the parameter R. Clark found that the vast majority of precipitates formed were allo-triomorphs— lens-shaped precipitates that grew along the grain boundaries. At low-angle boundaries, however, (R < 15 deg) Widmanstatten sideplates nucleated at the grain boundaries and grew into the adjacent grains. It has been reported that the rate of growth of grain boundary precipitates is controlled by diffusion within the supersaturated phase.&apos; The theories which have been developed for growth rates have assumed the diffusion coefficient constant over the composition range of the supersaturated phase. This is a fairly good approximation if the composition range involved is not large. Thickening rates have been calculated using the theory developed by Zener4 and by Frank5 for the growth of planar precipitates. A parabolic growth law

Jan 1, 1968

By T. E. Scott, D. H. Sherman, C. V. Owen

It has been established&apos; that vanadium exhibits a ductile to brittle transition temperature which increases with increasing hydrogen content. Optical microscopic examination at room temperature revealed no evidence of hydride precipitate in fractured specimens containing 100 ppm H, but hydrides were present in samples with 800 ppm H. More recently2 the strain rate and temperature dependences of the ductility drop in vanadium containing 6 ppm H were reported. It was argued that the ductile-brittle transition, while dependent on the presence of hydrogen, probably could not be explained by the precipitation of hydride. The bases of the argument were that 6 ppm H would not produce sufficient hydride to alter the ductility to the extent observed and no visual evidence of hydride was obtained. However, the data were not sufficient in these investigations 1,2 to define accurately the ductile-brittle transition temperature. Also, no information was available concerning the terminal solubility of hydrogen in vanadium at the low concentrations employed. westlake 3 has studied the electrical resistivity of vanadium at several hydrogen concentrations. He was able to detect the precipitation of hydride and to extend the hydrogen solvus to the composition and temperature range pertinent to the observed ductile-brittle transition behavior, Westlake compared his

Jan 1, 1968

By H. C. Fiedler

THE development of the cube-on-edge secondary re-crystallization texture in Si-Fe strip depends upon the ability of inclusions to restrain normal grain growth. This ability is determined by the number and size of inclusions, which, for a given composition, is controlled by the thermal history of the material during the prior processing.&apos; It has been shown2 that increasing the silicon content decreases the solubility of sulfur, and it is the purpose of this note to show the consequences of this decreased solubility for secondary recrystallization. Heats were made as previously described and cast into graphite molds.&apos; The compositions are shown in Table I. Slabs 1 in. thick were cut from the ingots and either hot-rolled from 1000°C in the as-cast condition or after one of the heat treatments described later. The processing to the final gage of 12 mils followed the previous procedure.&apos; To avoid cracking, the 5.2 pct Si alloy was cold-rolled at 150" to 200°C rather than at room temperature. The percent cube-on-edge texture developed by isothermal heat treatments was determined by dividing the maximum torque measured on disk sam-

Jan 1, 1968

By A. W. Schlechten

The proposition is advanced that edutcation specifically for exlractive metallurgy is desirable not because the course content is cmique but rather as a means of indoctrinating the student with a backgrocmd that will give him an interest and pride in the profession. Factors that have caused the decline in enrollment in metallurgical engineering courses emphasizing extractive processes are being overcome. There is a need to distinguish between the sciences of metallurgy and the engineering applications to avoid confusion both in and out of the profession. AS a first step in preparing the 1967 EMD Lecture I searched the literature to determine what my predecessors had done hoping thereby to gain some clues for my own performance. The Transactions of the Metallurgical Society show that the first EMD Lec- turer in 1959 was Dr. W. J. Kroll, known chiefly today for his pioneering work on the production of titanium and zirconium, but equally respected by an earlier generation for his contributions to lead refining. He has been followed by a series of well-known and competent metallurgists all possessing specialized knowledge that has served as a basis for their lectures. The EMD Lectures have in general been a review of the development of a certain aspect of the extractive metallurgical industry or a preview of a particular area of science or technology that has applications in extractive metallurgy. The usual format is to describe developments of the past, summarize the present state of knowledge, and make predictions for the future. There has been great variation in the relative amount of time devoted to these three subdivisions, the past, the present, and the future. For example, Professor Gaudin, the 1961 EMD Lecturer, in speaking of Separation Engineering on the Moon, did not have too many examples of past practice and so had to emphasize the future. It is cheering to observe that all of these authorities were optimistic in their predictions. Despite the fact that four of the previous EMD Lecturers have been educators, Professors Gaudin, Pidgeon, Schuhmann, and Kellogg, none of them discussed the subject of education for extractive metallurgists. I might say parenthetically that lecturers in other divisions, such as B. M. Larsen, J. B. Austin, F. D. Richardson, John Chipman, and R. F. Mehl, have commented with concern on the present state of training for extractive metallurgy. What can you say that is new about extractive metallurgy education? Certainly nothing new can be said about the educational process itself. Professional educators do have new approaches to teaching and learn-

Jan 1, 1968

By C. C. Harris

A critical literature review leads to a descriptive model of tumbling mill operation based upon energy partition concepts and the necessary requirements for particle fracture. As grinding proceeds into the ultra-fine region, conditions which are of little significance during normal operations gradually become controlling. These involve increasing resistance to fracture and an increasing tendency to aggregate as particles become smaller, and a growing fraction of the power input being consumed fruitlessly. The result is that fineness asymptotes to a maximum value as comminution proceeds indefinitely; thus where t is time, p and n are experimentally determined parameters, and Ø is a measure of fineness, which is presumed to be proportional to specific surface area, or proportional to the reciprocal of the size modulus (provided that the distribution modulus remains constant with time), or both. Ø, is the asymptotic value of Ø and is a measure of the grind limit. A method for its graphical determination is given. In a previous paper1 the physical and mathematical principles requisite to a study of the role of energy in comminution were reviewed. The micro-process of comminution — or the comminution event — can be investigated in terms of (a) the magnitude of the force-field localized around the individual particles which gives rise to the stresses generated in the particles, which in turn induces their fracture, and (b) the distribution of fragment sizes, should the event prove fruitful. The entire fragmentation operation can be considered to be the totality of its individual events, and in order to obtain a single independent variable of the process it is necessary to transform and sum the local stresses in terms of energy.1 This energy, however, will account for only a fraction of the energy input to the comminution process, the actual magnitude depending upon the kind of mill and several related factors. From the comminution viewpoint the primary function of a mill is that of stressing as many as possible of the individual particles of the charge to failure, with the maximum economy of energy expenditure. This is difficult indeed to achieve, for stressing a particle does not always break it, while the overwhelming portion of the energy input is involved with various internal mill processes which — almost incidentally — determine the magnitude, frequency, and manner in which the forces are applied to the particles. Essentially, these processes depend upon the mill dimensions, loading and speed, and they may be little affected whether fracture occurs or not. These processes must be delineated if a complete description of the role of energy in comminution is to be given; the energy account sheet1 (Fig. 1) in showing how the energy is partitioned for the requirements of the several functions it performs, provides a framework for the development of a model of the comminution process. Actual numerical values for the variables appearing in Fig. 1 will depend upon the mill, materials, and operating conditions. A possible general relationship between the variables will be suggested in this paper. Before proceeding further, a cautionary note must be issued. It was pointed out in an earlier paper&apos; that while energy input is not changed by increasing the power and decreasing the time in the same proportion, and vice versa, the results of the process in terms of particle fineness may be different. Thus, although energy is chosen as the independent variable of a comminution process, it is not absolutely independent, and care must be exercised to ensure that it is used within its range of valid application. Time has the necessary independence, and it will be used in place of energy where it is appropriate. The residence time in a mill is usually of the order of minutes. Under these conditions the particles are subjected to "... a relatively constant fracture producing environment".2 However, under the more rigorous conditions of greatly extended time, which pertain in ultra-fine grinding, indications are that the fracture producing environment no longer remains constant; this is the major subject of this paper. At this extreme limit the mill is probably taxed to its utmost, and at the same time the bulk material properties are becoming closer to ideal, while the physico chemical effects associated with surfaces, edges and corners are multiplying. (The edge length per unit volume is proportional to the square of the specific

Jan 1, 1968

By G. V. Sirianni, G. E. Viens, R. A. Campbell, G. N. Banks, R. L. Sachdeva

"A combined shaft-electric furnace for the smelting of ores and the melting of metallized iron pellets is being developed. The materials are preheated, and in some cases pre-reduced, in the shaft before being transferred to the electric furnace, where melting or smelting is completed. It has been demonstrated that this combination of equipment will enable much of the relatively expensive electrical energy to be replaced by cheaper energy in the form of oil or natural gas, and preliminary experiments indicate that the total energy requirements for a melting or smelting operation are significantly reduced. Projections based on results obtained from the preliminary experiments indicate that further improvements will be possible when certain modifications to the equipment are completed."

Jan 1, 1968

By Frank W. Dickson, George Tunell

Five hot spring areas of the western United States show evidences of present day deposition of HgS; two also show evidences of accompanying Sb2S3 deposition. Sulfide minerals are depositing at or near the surface from hot waters that differ for each spring ai:ea in amount and kinds of dissolved matter. All the springs contain dissolved substances that act as buffering agents and that cause increased alkalinity with increasing temperature. Transport of Sb2S3 is possible in H2O and in boron and sulfide solutions. Increasing alkalinity and temperature enhance stibnite solubility. Quantitatively important transport of HgS appears restricted to alkaline sulfide solutions that contain HgS2=. Elemental mercury probably forms in deep hot waters because HgS breaks down into mercury and sulfur above 200°C, and free S is removed by reaction with water. Elemental mercury should accompany HgS2= in solutions that were at 200°C or higher. Cinnabar deposits from saturated alkaline sulfide solutions because of combinations of temperature decrease, dilution, oxidation, and reactions with wall rock: Amedee Hot Springs, Boiling Springs, and Coso Hot Springs are areas in which HgS is the only sulfide deposited. Hot waters at Amedee and Boiling Springs are supersaturated with HgS or transport colloidal HgS. Steamboat Springs waters deposit mainly silica and stibnite, but they have deposited HgS recently. Sulphur Bank waters deposit mostly stibnite and some HgS. The hot-spring waters of all springs represent highly modified deep water. Field and laboratory studies support the concept of transport of HgS in moderately alkaline sulfide solutions as HgS2=. Fluctuating deposition of stibnite and cinnabar reflects availability of sulfide or variations in deep-source HgS and Sb,S,. Silica and HgS dissolve mutually in alkaline sulfide solutions, and cinnabar and quartz would be expected to deposit simultaneously. Free mercury given off by hot-spring waters would impregnate country rocks.

Jan 1, 1968

By B. H. Kear, B. J. Piearcey

The orientation and temperature dependence of the tensile and creep propevties oj Mav-M200 crystals halle been determined. Crystals oriented for single slip exhibit ,maximum ductility, minimum work hardening, and least creep resistance, whereas crystals in multiple slip orientations show nzinimu~n ductility, strongest work hardening, and greatest creep resistance. At 1400" and 1600°F there is a marked improzlenzent in creep strength for orientations approaching [001] and [111], indicating that interactions between dislocations gliding in intersecting octahedral slip systems play an important role in creep resistance. At 1800°F the creep strength is much less dependent on orientation, which is rationalized in terms of slip in cube planes as well as octahedral A frequent mode of failure in high-strength cast nickel-base superalloys is by intergranular fracture, particularly along those grain boundaries oriented transverse to the major stress axis. VerSnyder and ~uard&apos; demonstrated that this problem could be overcome by eliminating transverse grain boundaries through unidirectional solidification. Piearcey and versnyder2 made use of this principle in the development of unidirectionally solidified gas turbine blades and vanes, where the growth direction of the columnar grain structure coincides with the axis of principal stress under operating conditions. The present investigation was undertaken to determine if further improvement in properties may be obtained by eliminating grain boundaries altogether, so as to take advantage of the well-known dependence of mechanical properties of single crystals upon the orientation. 1) EXPERIMENTAL PROCEDURE Single crystals of Mar-M200* were grown from the melt under vacuum by a modified Bridgman method. The melt was poured into a preheated alumina mold, and crystal growth was promoted from one end by appropriate gradient cooling. Tensile and creep specimens (2 in. diam by $ in. gage length) were prepared by a series of operations involving electrical discharge machining, precision grinding, and electropolishing. The orientations of the specimens were determined by the Laue X-ray back-reflection method. Tensile tests were carried out in aWiedemann machine with furnace attachment, using a strain rate planes. In all orientations imzpvouement in the strength charactevistics of the material can be induced by heat treatment. Creep ad stress rupture data for (001) oriented crystals are compared with similar data obtailted previously joy random polycvystalline material, and also columnar grained material having a prejevved (001) orientation. The single-crystal )material exhibits both longer rupture life and lower minimum creep rate at all temperatuves, and the rupture elongation is comparable with that in the columnar grained material. From these results it is concluded that single crystals should and useful application in gas-turbine blades and tanes. The optimum orientation for a blade is considered to be with its axis of principal stvess parallel to (001) ou (111). of 0.0001 sec-&apos;. Load and extension were recorded directly on an X-Y recorder. The strain measuring device consisted of extension arms attached to the grips at one end and leading out of the furnace to an LVDT (linear variable differential transformer) at the other. Creep tests were performed using a standard constant load creep frame. 2) DISCUSSION OF RESULTS 2.1) Structure of Alloy. The structure and segregation in as-cast and heat-treated Mar-M200 has been described in detail else where.~ The main features are as follows: the as-cast material is heavily cored, due to pronounced dendritic segregation during solidification; the dendrites are rich in tungsten and cobalt whereas the interdendritic regions are rich in chromium, titanium, nickel, and carbon. The structure consists of -60 vol pct coherent precipitate of y&apos;, basically Ni3(A1,Ti), in a matrix of y (nickel-base solid solution), interspersed in the interdendritic regions with minor MC carbides and -y&apos; eutectic. The y&apos; particles, and y-y&apos; eutectic, contain more titanium, aluminum, and nickel, and less tungsten, cobalt, and chromium than the y matrix. Heat treatment partially removes segregation, eliminates the eutectic, refines the y&apos; dispersion in y, and gives additional partially coherent M23Cs carbide. An as-cast crystal, therefore, is composed primarily of two oriented phases (y + y&apos;), whereas the normally heat-treated crystal consists of three oriented phases (y + y&apos; + MZ3Cs). Typical electron transmission micrographs of the y + y&apos; structure are shown in Fig. 1. Crystals grown in the (100) orientation develop a simple unidirectional dendritic structure, Fig. 2, since (100) happens to be the preferred direction of growth for dendrites in this material. Crystals grown in the {110) and (111) orientations, however, tend to promote equal growth, generally in separate colonies, in the two and three geometrically favored (100) growth directions, respectively. In other orientations of growth, a single (100) dendrite direction generally pre-

Jan 1, 1968

By E. Miller, J. M. Eldridge, K. L. Komarek

Aclivilies of magnesium in liquid Alg-Si alloys have been delermined between 5 and 60 at. pcl Si, close to the melling point of Mg2Si, by an improved isopieslic melhod. Silicon specinrens, held in alumina crucibles and graplrile conlainevs of special design, were healed in a letrlpevalure gvadient and equilibrated with mag-nesilcrrl rapor in a closed lilanium system. The ther-madynamic Junctions were calculated and compared with the thermodyuamic properties of the other three mg- Gvoup IVB systems. Lattice paramelers of three Mg2X compounds were measured. The bonding in the Mg2X compounds is largely covalent with small and uarying amounts of metallic and ionic conlvibutions. The Mg-Si phase diagram1 has one congruent melting compound, Mg2Si, of essentially stoichiometric composition, two eutectics, and very limited terminal solid solubilities. Little information is available on the thermodynamic properties of this system. The free energy of formation of Mg2Si has been determined by the Knudsen cell technique2 in the range 572" to 680oC, by the transportation method3 between 858" and 950oC, and by the electromotive-force method4 in the range 400o to 600°C. Kubaschewski and villa5 and caulfield6 have measured the heat of formation of Mg2Si. An electromotive-force study of magnesium-rich liquid alloys was recently published by Sryvalin el al.7 The present investigation was undertaken to complete a general survey of the thermodynamic properties of the homologous series of Mg-Group IVB systems, i.e., Mg-Pb,a9,Mg-Sn,10,11 mg-Ge,12and Mg-Si. An isopiestic technique, previously developed for similar measurements on liquid Mg-sn11 and Mg-Ge alloys,12 was modified for the Mg-Si system. Specimens of the nonvolatile component, silicon, were contained in dense alumina crucibles placed inside covered graphite crucibles which were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure. The alumina crucibles prevented contact between the highly corrosive liquid Mg-Si alloys and graphite. The graphite cruci- bles effectively preserved the high-temperature equilibrium composition of the liquid alloys containing highly volatile magnesium on termination of the experiments during the quench to room temperature. EXPERIMENTAL PROCEDURE Silicon of semiconductor-grade purity (E. I. du Pont de Nemours and Co., Brevard, N.C.) and 99.99+ pct Mg (Dominion Magnesium Ltd., Toronto, Canada) were used. Graphite crucibles with press-fitted lids were machined from high-density (1.92 g per cu cm) rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The alumina crucibles had a purity of 99.7+ pct (Triangle RR grade, Morganite, Inc., Long Island City, N.Y.). In preliminary runs the liquid alloys were contained in graphite crucibles following the exact procedure developed for the Mg-Ge system.&apos;2 These runs failed due to appreciable reaction between the molten Mg-Si alloys and graphite, and the results have been discarded. The procedure was then modified and the Mg-Si alloys were subsequently held in alumina crucibles. For most of the runs alumina crucibles of known weight and approximately 6.3 mm ID, 12.5 mm height, 1.0 mm wall thickness were loaded with weighed amounts of silicon and encapsuled in tightly covered weighed graphite crucibles 5/16 in. ID, 2 in. helght, 3/32 in. wall thickness). The graphite crucibles were machined from rods which were 85 pct of the theoretical density. These crucibles were therefore sufficiently porous so as to permit magnesium vapor to effuse through the silicon under the experimental conditions of approximately 970O to 1220°C and 1 day equilibration time. However, negligible magnesium was lost from the crucible during the quench due to the slow effusion rate through the pores of the graphite. The inner alumina crucible prevented the liquid alloys from contacting the graphite, and the very tightly fitting graphite crucible lids served to retain any magnesium vaporizing from the alloys inside the crucibles during the quenching step.12 The loaded silicon-alumina-graphite cells were positioned, one above another, on a 16-in.-long titanium thermocouple well and tied securely to the titanium tube with thin molybdenum wires held in grooves around the circumference of the graphite crucibles. A thin (0.005-in.) molybdenum strip prevented contact between the graphite crucibles and the titanium. This assembly was lowered into a titanium reaction tube (la in. ID, 16 in. long, $ in. wall thickness) closed on one end which contained a 11/2-in.-long cylinder of magnesium at the bottom. The inner titanium thermocouple well was positioned eccentrically in the large tube because of the eccentric mounting of the cells on the well. Appropriate modifications of the titanium cap"&apos;12 were made to join the inner and outer titanium

Jan 1, 1968

By Cyril Jones

13.9-1. Introduction. Any mining venture or project is undertaken with a view of gaining some benefits, which, with the modern limited corporation, means earning a return to the stockholders for the use of their funds. Thus, any manager, when confronted by an opportunity of expending funds, must realize that the funds should generate a satisfactory return. The problem then becomes one of how the manager should best expend, if he should expend, funds for opportunities that become available to him. In the evaluation of a mineral property, or of a project within an operating mineral property, there must be cognizance of the fact that the final return is dependent on many factors that are not present in other industries. The primary factor in mining operations is the orebody, which has a diminishing life. This diminishing life gives the decision maker a range of choices; for by expending more capital for a larger plant, he can work the deposit out in a shorter period (16). This may, in fact, maximize the return on the investment. Alternatively, he may wish to maximize the total profits, a course which usually requires a lower capital investment and allows a longer working life for the deposit before final depletion. Other factors that have great importance in the evaluation of mining projects are the taxation treatment of mining profits from the viewpoint of depletion, depreciation, and investment credit. Investment opportunities involve expending funds at the present time in return for future benefits. These future benefits have a degree of risk in that the annual amounts of benefits and their duration cannot be fore- cast accurately. The treatment of risk in economic analysis involves the quantification of the degree of variability of the expected future benefits and also of the initial capital expenditure. This treatment in mineral exploration may be extended to cover the initial search for an orebody

Jan 1, 1968

By B. E. Terkelsen, B. J. Piearcey

A study has been made of the effect of unidirectional solidification on the creep behavior, stress-rupture properties, and thermal shock resistance of four nickel-base superalloys. The alloys Mar-MZOO, B-1900, IN 100, and TRW 1900 show improved rupture ductility and thermal shock resistance when tested with the columnar grains parallel to the major stress axis during test. The relative improvement in creep-rupture properties depends on the intrinsic strength of the alloy, a property which depends on composition, heat-treatnient, and crystallographic orientation. The data clarifies some of the factors affecting the properlies of the cast nickel-base superalloy. COMPONENTS designed for high-temperature use have, in recent years, been fabricated by precision casting techniques using nickel-base alloys developed specifically for use in the conventionally cast condition. This development was a result of both the increasing complexity of the component and the recognition that high-temperature strength was incompatible with workability. The use of castings can be economically favorable, but, more important, the recent complex designs of air-cooled gas turbine blades and vanes in alloys which possess the necessary high-temperature strength cannot be forged. Common modes of failure of high-temperature components are excessive creep, creep rupture, and thermal fatigue. If rupture occurs then the mechanism is usually by inter crystalline cracking along those grain boundaries oriented transverse to the major stress axis. In the stronger alloys, rapid propagation of intercrystalline cracks result in apparent premature failure demonstrated by the absence of third stage creep in a creep-rupture test and low rupture ductility. Tensile ductility shows a similar trend, that is, decreasing ductility with increase in strength. It is not surprising, therefore, that increases in creep strength have only been obtained with a loss in resistance to thermal shock, a property which shows a dependence on tensile ductility. VerSnyder and ~uard&apos; showed that the application of unidirectional solidification to a brittle Ni-Cr-A1 alloy both improved the rupture life of the alloy and increased rupture ductility. Since this casting method results in columnar grains, it appeared that the solution to the lack of ductility in nickel-base alloy components was the elimination of the source of failure, namely the transverse grain boundaries. This concept was recently developed2 to produce cast-to-size gas-turbine blades and vanes consisting entirely of columnar grains oriented parallel to the major stress axis of the component. Not only did the process impart increased rupture life and ductility to the components, but it also increased their resistance to thermal shock. During this development, the effect of unidirectional solidification on the properties of several alloys was investigated. The resulting data allows certain conclusions to be drawn regarding the factors affecting the creep and stress-rupture properties of the cast nickel-base superalloy and also its resistance to thermal shock. Detailed information was obtained on the alloys Mar-MZOO, B-1900, In 100, and TRW 1900. The composition of the alloys studied are shown in Table I. MATERIAL PREPARATION AND TESTING The conventionally cast alloys are cast as +-in.-diam bars in innoculated shell molds under conditions designed to maintain control of grain size. Unidirec-tionally solidified casting were produced in the form of 3-in.-diam ingots. Specimens from the latter were machined such that the axes of the columnar grains were parallel with the axis of the test bar, except in certain cases where the transverse properties of the material were being evaluated. The specimens were tested in an axial loading creep machine.&apos; Temperatures were measured with thermocouples, attached just outside each end of the gage length, to assure uniform temperature along the entire specimen. Chromel/alumel thermocouples were used up to 1800"F and Pt/Pt-10 pct Rh thermocouples above 1800"F. The specimen temperature was recorded and maintained within i2"F throughout the test. Creep extensions were measured automatically with extenso-meters attached to ridges on the specimen and recorded continuously using linear variable differential transformers and multipoint recording equipment. MICROSTRUCTURE The microstructures of transverse sections of the four alloys studied are shown in Figs. 1 and 2. Fig. 1 shows optical micrographs of the alloys, both in the conventionally cast and unidirectionally solidified conditions. Each alloy displays a cored dendritic structure, a distribution of MC carbide, and the presence of the y — y&apos; eutectic constituent.~ In the case of IN 100 and B-1900, Fig. 1 indicates that in these specimens the eutectic is degenerate. That is, it consists only of y&apos; pools indicating that the y constituent has been solutioned during the cooling period after solidification. The major effect of unidirectional solidification on the microstructures of the alloys is a tendency to promote a more dendritic form of MC carbide and an increase in dendrite arm spacing, both effects being a result of the slower solidification rate in the unidirectional solidification technique. V, lec tron micrographs of transverse sections of the four alloys in the two cast conditions are shown in

Jan 1, 1968

By R. W. Smashey, B. J. Piearcey

The structure, composition, and morphology of the carbide phases present in the nickel-base superalloy, Mar-M200, hare been determined and three carbide phases observed. The MC carbide is a solidification product, and the M23 Co and M6C carbides are both prod~icts of solid-state precipitation. The identity of each phase usas determined by both X-ray and electron-diffraction techn~ques. Compositions of all three carbides were studied using the electron beam micro-probe analyzer and by unalyszs of electrolytically extracted residues. Optical and electron microscopy were employed in order that the time/temperature -dependent behavior of the carbides might be observed. Supplementary studies were completed on thin foils and oriented single crystals to determine the mor-phology and orientation relationship of each phase with that of the matrix. MAR-M~OO* is a high-temperature, creep-resistant superalloy designed for use in the as-cast condition. The "as-cast" microstructure consists of a solid-solution matrix, referred to as gamma (y), which contains a general, coherent precipitate of the inter-metallic Ni3(A1,Ti) referred to as gamma prime (?). As a result of dendritic segregation during solidification, a degenerate, spherulitic ? -?&apos; eutectic constituent is present at the grain boundaries and the in-terdendritic regions, which is nucleated by the y on the dendrite tips. A primary carbide phase, a solidification product, is also present at the grain boundaries and in the interdendritic areas, and an additional carbide appears at the grain boundaries as a fine discontinuous precipitate. The alloy is particularly susceptible to heat treatment. For example, the mechanical properties of the columnar grained mater- ial are substantially improved by solution heat treatment, followed by an intermediate temperature age. Metallographic examination of heat-treated material reveals, however, that exposure to elevated temperatures has a marked effect on the microstructure of the alloy; in particular, it is observed that precipitation of considerable amounts of various carbide phases occur. The following investigation was carried out to determine the morphology, composition, and behavior of the carbides in Mar-Ma00 as an aid to the determination of their effect on the mechanical properties and stability of the alloy. THE PRIMARY MC CARBIDE The MC carbide phase appears in the interdendritic interstices and the grain boundaries. In directionally solidified Mar-M200 the carbide appears as very small particles in the chilled region, Fig. l(a), whereas in material less affected by the chill, it becomes larger and develops a dendritic morphology, Fig. 1(b). Step polishing of metallographic specimens from this region shows that in directionally solidified material the individual carbide dendrites are connected in a dendritic network within the metallic interdendritic interstices, whereas in material from the chilled region and in conventional Mar-M200 they are discontinuous, isolated dendrites. No orientation relationship exists between the primary carbide and the matrix.

Jan 1, 1968