Search Documents

By R. B. Tippin

Research investigations conducted on five ore samples show the applicability of heavy liquid separation (HLS) techniques to mineral processing. Under proper operating conditions, semicontinuous tests in small fluid cyclones yielded 90 percent sink-float concentrates with recoveries exceeding 90 percent on minus 35-mesh ore samples of kyanite, potash, spodumene, fluorspar, and beryl. Although none of the ores were examined in detail, their response to this novel concentration method provides basic examples that are typical of the process. Various aspects of cyclone design and operational characteristics of heavy liquid cyclone circuits were studied which demonstrated the flexibility of HLS by using multiple units connected in series. A comparison of two heavy liquid solutions, tetrabromoethane and methylene bromide, exhibited their individual advantages and limitations. Unique problems relative to this process are discussed including liquid viscosity, mineral composition of the ore, toxicity, and material handling hazards.

Jan 1, 1968

By P. S. Rudman

The solubility limit and the diffusivity of carbon in molybdenum have been obtained by duffising carbon into molybdenum rods from a Mo + Mo2C powder mixture. The solubility limit was taken as the long-time asymptotic limit of the rod composition. The diffusiv-ity was obtained from fractionally saturated rods from the rate of change of the average composition. Compositions were determined by chemical analysis. The solubility limit obtained is: WhILE the Mo-C system is important in refractory alloy technology neither the solubility limit nor the diffusivity of carbon in molybdenum is unambiguously known. In Fig. 1 the Mo-C phase diagram is presented. The heavy lines, the terminal solution solubility limit, and the eutectic temperature are results of the present investigation and will be discussed in detail later. However, it is readily seen that the previously published solubility limit determinations, Few and Manning1 and Fromm and ROy2 differ by up to an order of magnitude. The general form of Fig. 1, the Mo2C field, and a eu- tectic temperature -2200°C are due to an early Investigation by Sykes et a1.3 Although they did not determine the solubility limit, they did establish that the maximum at the eutectic temperature was about 1000 ppm. The only other prior data found on the solubility limit is from a lattice-parameter study by Speiser et a1 .,4 from which it can be concluded that the maximum solubility is greater than 1800 ppm. There does not appear to be any data oh the diffusivity of carbon in molybdenum. However, Samsonov and Epik5 have determined, from the rate of growth of an MozC layer, the diffusivity of carbon in Mo2C, and this has been erroneously interpreted, for example by ~c~eil,' as applicable to diffusion of carbon in molybdenum.

Jan 1, 1968

By F. W. Wood

The use of consumable.-electrode arc melting as a production technology is growing. One advantageous feature of this process is that it avoids ingot contamination by soluble crucible materials by employing a chilled metal crucible. Because the thermal balance under these conditions is rather delicate and does not necessarily provide a favorable environment for solidification, catastrophic imbalances can occur. The effectiveness and mechanistic roles of various factors are mostly unknown, and more intelligent insight regarding the distribution of temperature and heat is needed. Experience has provided several pertinent observations, some of which are quite superficial. The most meaningful data have resulted from studies of molten pool shapes and sizes and from measurements of heat flow through crucible walls. Overall experience, intuitively interpreted and supplemented, is sufficient nevertheless as a basis for a boundary-value treatment of the problem. A mathematical analysis based on a separation of variables, using conventional differential equation methods, provides a useful solution. For a cylindrical ingot, the temperature varies as a Bessel function of an argument proportional to the radius and as an exponential function of longitudinal position. Trial calculations using the problem solution seem to verify the general correctness of the result as compared with experience. The role and nature of solution parameters are also clarified, though not entirely resolved. It is revealed that the barrier to heat flow at the ingot-crucible surface has a prominent influence. Utility of the model embodied in the problem solution is readily demonstrated by considering a variety of contemporary questions about arc melting, and it is hoped that utility can be enhanced by improvement of the model.

Jan 1, 1968

By R. M. Hays

Prior to use of this model siphon finisher, the only means of evaluating metallurgical performance of the siphon finisher was by pilot plant studies. These are costly and require large quantities of material. A model siphon finisher and a test procedure which permits the evaluation of siphon finisher metallurgical performance has been developed. Metallurgical results between the model siphon finisher and pilot plant or commercial units show fairly good correlation. The upgrading of magnetic taconite concentrates by hydraulic concentration has been practiced for several years. In the 1940's, Braund1 used a multistage upflow classifier to upgrade magnetized magnetic concentrates. In present taconite plants, the SiphonSizer, marketed by Dorr-Oliver, Inc., has been particularly suitable for upgrading magnetic concentrates. When the hydraulic SiphonSizer is used to upgrade the concentrates in the finishing portion of the overall flowscheme, the unit will be called a siphon finisher to distinguish this application from classification. Prior to this work the only means of evaluating the metallurgical performance of the siphon finisher was by pilot plant studies which are costly and require large quantities of material. Therefore, it was desirable to develop a model siphon finisher and a test procedure which would simulate siphon finisher performance and require only small samples of material. This model would permit the evaluation of small samples such as drill core samples and be useful in evaluation of commercial siphon finisher design and performance. THE SIPHON FINISHER The siphon finisher, as shown in Fig. 1, is a tank equipped with a system of water jets which distribute the hydraulic water uniformly across the bottom of the vessel with an energy release for agitation in the teeter bed. The feed to the siphon finisher is intre duced through a feed well in the center of the unit. The silica and middling particles overflow a peripheral weir into the overflow launder. The magnetite fraction is discharged by a siphon or a modulated discharge valve. The siphon or the discharge valve is usually operated automatically by a float assembly which is responsive to the depth of the teeter bed. Various interface sensing devices have also been

Jan 1, 1968

By N. C. Carter, Wm. H. White, J. E. Harakal

"Of twenty-one ore deposits in British Columbia which are either in production or advanced stages of exploration, five have potassium-argon ages in a range of 165-205 m.y., eight are in a range of 44-55 m.y. and the remainder are either ca. 140 m.y. or ca. 100 m.y. old. Deposits of the oldest group have generally similar geological environments and radiometrically indistinguishable ages of magmatic and hydrothermal minerals. Deposits of the youngest group also have similar geological environments, with successive magmatic and hydrothermal events closely intermingled in time and place. Such deposits find no comfortable home in existing classifications of ore deposits. 1t is suggested, therefore, that those epigenetic deposits which can be shown by radiometrie and/or geologie means to be coeval with genetically related magmatism be designated as ""paramagmatic deposits."""

Jan 1, 1968

By J. L. Goodier

The paper points up the hesitance of private capital to pursue development of offshore mineral mining endeavors due to the deterrent effect of the clouded legal status of such endeavors. Some states have no laws or regulations to protect the potential exploiter. Others have regulations which give no proprietary rights of exploration to mineral discoveries. The above factors and others are discussed and analyzed in some detail, covering, in turn, summations of the federal regulations and of each of the coastal states. Some comparative analyses are provided, and some recommendations for encouragement to capital investors are made.

Jan 1, 1968

By M. S. Burton, J. E. Ritter

The sessile-drop technique was employed to study the effect of atmosphere and alloy additions of titanium and chromium on the surface tension and contact angle of nickel on sapphire substrates at 1500oC. Shear tests were conducted on the solidified sessile drops. The liquid-gas surface tension of pure nickel on sapphire was found to be 1747 ergs per sq cm, with a contact angle of 109.6 deg. The surface tension and contact angle were not affected significantly by the four atmospheres, vacuum, impure argon, pure argon, and pure hydrogen. Small additions of titanium and chromium decreased the contact angle and for the same alloy content, contact angles were lower in pure argon than in pure hydrogen. On the basis of shear-test results , the most probable cause for adhesion in the Ni-Al2O system is the formation of NiO:Al2O3 spinel at the interface; in the titanium alloy-Al2O3 system adhesion is thought to be due to a mechanical interlocking effect; in the chromium alloy-Al2O3 system adhesion is believed to be the result of solid-solution formation involving Cr2O3 and Al2O3 at the interface. In the last few years there has been considerable interest in reinforcing metals with ceramic whiskers. It has been postulated that, by reinforcing nickel with sapphire whiskers, high-temperature strengths su- perior to those of the best current nickel alloys can be achieved.' To fabricate a whisker-metal composite having optimum density and strength, understanding of wettability and adherence in the system is of prime importance. Although there has been some previous research in this a a need for further studies has been cited4-8 to understand better the effects of impurities, alloys additions, and atmosphere on the wetting and bonding of metals to metal oxides. The purpose of this research was to investigate the factors involved in the wetting and adherence of nickel/nickel alloys to sapphire (single-crystal a Al2O3). Sessile-drop experiments were conducted in vacuum, impure argon, pure argon, and pure hydrogen, to determine the effect of atmosphere on the contact angle of the metals on sapphire, and the liquid-gas surface tension of pure nickel. The solidified sessile drops were sheared from the sapphire substrate to measure the bond strength between the metal and ceramic. The alloy additions chosen were titanium and chromium since both enhance the wetting of nickel on sapphire.2, 3c Also, titanium is commonly used when brazing metal-to-ceramic seals to improve adherence. Since chromium forms an oxide that is completely soluble in sapphire, it was thought that the oxide could serve as a transition phase to promote bonding between the Ni-Cr alloy and sapphire. I) EXPERIMENTAL APPARATUS AND PROCEDURE The sessile-drop apparatus was a horizontal furnace, with an induction-heated, cylindrical molybdenum susceptor in a water-cooled Pyrex chamber. This apparatus was patterned after that of Williams and Nielsen.7 A flat Pyrex window at each end of the furnace allowed temperature measurements to be made at one

Jan 1, 1968

By N. B. Gray, R. V. Culver, W. S. Boundy, N. W. Stump

The kinetics of sulfation of single crystals of lead sulfide to lead sulfate have been studied between 969" and 1073°K in gas atmospheres of known composition using a thermobalance technique. The data are described by an equation derived on the basis that diffusion outward through the Product layer is the major controlling step. The rate of sulfation is linearly related to the logarithm of the sulfur trioxide partial DESPITE its industrial significance the oxidation of lead sulfide has received limited attention. The oxidation reactions have been studied using beds, briquettes, single crystals, or thin films of lead sulfide. Lead oxide and lead sulfate (PbSO,) were formed when Mclntoshl and Gardner2 roasted beds of galena pressure and the temperature coefficient of reaction is 40 ± 5 kcal per g mole. Gold marker experiments show that the sulfate layer grows by outward movement of ions through the sulfate layer. Initially the PbSO, adheres to the PbS but later forms an irnpewious spheroidal envelope; PbS vaporizes and pb2' ions diffuse through the envelope to react at the external surface. in air at temperatures up to 800°C. In a more extensive investigation, Tchizhykov3 obtained Pb, PbO, and PbS04 in accordance with Eqs. [1] to [4], when a bed of -200 mesh galena was oxidized in O2-N2 mixtures at 700° to 900°C.

Jan 1, 1968

By E. Miller, J. M. Eldridge, K. L. Komarek

The thermodynamic properties of- liquid Mg-Pb allojs have been determined by an isopiestic method from 18 to 42 at. pct Pb and by a thevmodynumic analysis of the phase diagram frofiz 0 to 100 at. pct Pb. In the overlapping composition range the magneszupn activity values derived by the two methods are in excellent agreement, thus mutually supporting the correctness of the Mg-Pb phase diagram previously determined by the authors and of the acticitzes deriz~ed isopiestically. SEVERAL studies have been made of the thermody-namic properties of liquid Mg-Pb alloys. Wagner and Engelhardt,1 Lantratov,2 Knappwost,3 Sryvalin et al.* and Wilson5 used the electromotive-force method, Scheil and Wolf8 and Schmahl and Sieben" applied the transpiration technique, and the present authors8 utilized the phase diagram to determine the activity of magnesium in the Mg-Pb system. The results of these studies are not in very good agreement and could not be incorporated into a general systematic analysis of the thermodynamic properties of the homologous series of the Mg-Group IV B systems Mg-Pb,8 Mg-Sn,° Mg-Ge,10and Mg-Si.11 The thermodynamic properties of the Mg-Pb system were therefore re investigated by an isopiestic technique which has been developed for similar studies in the Mg-SnB and Mg-Ge10 systems- Lead specimens, contained in iron or graphite crucibles, were heated in a temperature gradient in an evacuated and sealed titanium reaction tube and equilibrated with magnesium vapor of known vapor pressure to form alloys of compositions which depended on their temperatures, the temperature of the magnesium vapor source, and the thermodynamic properties of the system. EXPERIMENTAL PROCEDURE Magnesium (Dominion Magnesium Ltd., Toronto, Canada) of 99.99+ pct purity and lead (American Smelting and Refining Co.) of 99.999 pct purity were used. In the early experiments, Runs 2 and 3, the alloys were contained in uncovered high-purity iron crucibles. Alloys formed in the uncovered iron crucibles had to be chemically analyzed owing to the slight volatility of lead under the imposed experimental equilibration conditions. The compositions of these alloys were determined by a gravimetric analysis of lead as lead chromate. To avoid this problem, the remaining runs were made in covered graphite crucibles machined from high-density (1.92 g per cu cm) graphite rods (Basic Carbon Corp., Sanborn, N.Y.) which had a maximum ash content of less than 0.04 pct. The non- i reactivity of graphite with lead and magnesium has been previously established,' and the experimental procedure has been described in full detail.' In the runs using covered graphite crucibles it was found that the weight increases of the crucibles and their contents after equilibration equaled the magnesium contents of the alloys within the accuracy of the chemical analysis (i0.3 at. pct Pb). Clearly, the small lid openings of the graphite crucibles prevented significant lead losses during a run, and the weight increase was therefore taken as the magnesium content of the alloys. EXPERIMENTAL RESULTS At thermodynamic equilibrium the magnesium partial pressure of the specimens equaled that of the reservoir. Since the magnesium reservoir was always maintained at the temperature minimum of the system, the activity of magnesium of any specimen was given by the ratio of the magnesium reservoir pressure to the vapor pressure of pure magnesium at the specimen temperature. The standard state was chosen as liquid magnesium and the vapor pressure of liquid magnesium

Jan 1, 1968

By H. Habenicht, J. J. Scott

An experimental method is described to compare strain data for rock and rock bolts when exposed to shock waves released by blastings. Static and dynamic strains were measured. Bolt gage response indicated a static decay of the bolt anchorage coupled with a reaction due to blasting vibrations. A distinct loss of bolt tension was indicated during vibrations and this was accompanied by a smaller but steady loss of tension due to static loading. The strain losses were found to relate to the shock source distance and the vibrational amplitude in the rock and bolts. Millions of roof bolts are used each year to stabilize mine openings and prevent their failure. Frequently, bolts become loose and lose their effectiveness as reinforcement to the mine structure. Many attempts have been made to determine the cause of loosening, including observation of the bolt tension or bolt torque through the use of torque wrenches, compression pads, and load cells. Pull tests have been used extensively to determine anchorage characteristics.102 These investigations have shown that even when bolts are loaded below the nominal anchorage capacity of the rock under 'static' conditions they exhibit a decay of load through adjustments and slippage at the bolt anchor. Since bolts are quite often found with the plate hanging loose from the rock surface, this condition suggests that some additional mechanism may have played a part in loosening the anchorage. Vibration from blasting or shock loading have been suggested as one cause in this type of anchorage deterioration. This paper gives the results of an investigation carried on at the University of Missouri at Rolla to determine the influence of shock waves on rock-bolt anchorage stability. ROCK BOLT ANCHORAGE UNDER DYNAMIC LOADING CONDITIONS In this report dynamic loading conditions are defined as conditions under which rock and bolts are exposed to vibrations occurring as a consequence of blasting, machine vibrations, earthquakes, rock bursts, etc. Whatever the location of the shock source, the waves created suffer extensive alterations along their travel paths, depending upon the vibrational properties and geometric parameters of the transmitting media. Together with reflection, refraction and diffraction at material boundaries, waves suffer changes in their nature to form tensile, compressive and shear waves. They become polarized, retracted, accelerated, dispersed, so that the waves incident at a point in the material can be the result of either one or a combination of this wide range of processes. A certain fraction of the wave energy will be lost due to friction, deformation, and material failure at the anchor-rock contact. Thus, the physical nature of wave propagation is such that it inhibits an exact analytical solution. For this reason this investigation should be considered qualitative rather than quantitative even though numerical data have been used as a base. CONCEPT OF THE INVESTIGATION Experiments were designed to find, from a series of rock bolts installed in natural mine rock, whether or not, and to what extent, bolt tensions would be influenced when bolts were exposed repeatedly to shock waves such as those produced by blasting. Electronic instrumentation available in the rock mechanics laboratory of the University of Missouri at Rolla was used to observe wave development in the rock and vibrational reactions in the bolts. EXPERIMENTAL PROCEDURE Fig. 1 illustrates schematically the experimental equipment. Electric resistance wire strain gages were used as sensors for the strain response of the rock and the bolts. Bolts were 5 ft long and 5/8 in. in diam, equipped with two-leaf type expansion shells for 1 3/8 in. boreholes. The bolt gages were mounted by use of Du Pont Household Cement, covered with an epoxy insulation and then enclosed in a copper foil for electronic shielding. For details of placement and the wiring diagram see Fig. 2 and 3. The output of both the rock gages and the bolt gages was fed into cathode ray oscilloscopes from which the vibrational traces could be photographed. A static strain indicator was also used to read the output of all gages.

Jan 1, 1968

By H. E. Cline

Mechanical properties of the eutectic between CoAl and cobalt were measured over a range of- temnperatures and strain rates for a variety of microstructures produced by directional solidification and by thermo-mechanical processing. Directional solidification led to rodlike, lamellar, and irregular microstructures. The unusually high volume fraction of the cobalt-rich rods and the lurge spacing of the rods were explained by the phase diagram. The hot-worked structure consisted of fibers of COAL in a cobalt-rich matrix. The roonl- tevlperature strength of the uvrought material increased with decreasing grain size but the 1000°C strength decreased with decreasing pain size. At high temperatures the directionally solidified tnaterial was stronger and less strain-rate-sensitice than the hot-rolled material. The fine-grained hot-worked ma-terial became superplastic at high temperatures, with tensile elongations greater than 850 pct, while at root temperature this material was ductile and impact-resistant because of the ductile matrix. Fracture occurred in the directionally solidified material at elevated temperatures by inter phase separation and at roorn temperature by cracks in the intermetallic phase. Growth of these cracks was impeded by the ductile cobalt-rich phase. It was found that the CoAl intermetallic remains ordered at elevated temperatures. DIRECTIONAL solidification of eutectic alloys has been used to produce structures consisting of parallel rods or lamellae. Although the spacing of the phases depends on the growth rate, it has been observed to be of the order of 1 µ in many eutectics. A strong intermetallic phase has been used to reinforce a ductile matrix in the rod eutectic A1-Al3Ni and the lamellar eutectic Al-Al2cu.1 The microstructure of the eutectics A1-A13Ni and A1-A12Cu remained aligned after samples of these alloys were exposed to temperatures just below their melting points for long times. Stability of the microstructure at elevated temperatures makes directionally solidified eutectics a candidate for high-temperature applications. Recently Thompson4 has developed the Ni-NiMo eutectic containing 40 pct NiMo lamellae, giving a tensile strength superior to nickel-base superalloys. Unfortunately, this eutectic oxidizes rapidly at elevated temperatures. By mechanically processing a two-phase structure, one may reach strengths as high as 700,000 psi, as demonstrated by drawn pearlite.5 In this case the strengthening mechanism was thought to be related to the fine substructure formed during deformation.5 However, a heavily worked structure may recrystallize and coarsen at elevated temperatures. Some worked eutectics such as Al-Al2Cu,6 Pb-Sn,7 and Sn-Bi7 have shown unusually large elongations in tension when tested at elevated temperatures. This phenomenon of large extension, called "superplasticity", was related to the fine grain size of wrought two-phase alloys at elevated temperatures. A mode of deformation of "superplastic" material has been shown to be grain boundary sliding,' which has also been observed during creep of polycrystalline materials.9 The Co-A1 system was chosen for this investigation after examining the phase diagrams of binary eutectics." The high melting point of 1400°C, the aluminum content which was expected to give oxidation resistance, and the properties of the intermetallic CoAl were the chief factors influencing this choice. This eutectic consists of a mixture of the intermetallic CoAl and a cobalt-rich solid solution. The intermetallic CoAl has a large range of solubility and a CsCl structure." From the similarity between CoAl and NiAl one would expect CoAl to be ordered at elevated temperatures; however, specific heat measurements" show a transition at 800°C. West-brookL2 has measured the hot hardness of CoAl and found a rapid decrease in hardness above 600°C. The tensile properties and stress rupture properties of as-cast CoAl-Co eutectic were measured by Ashbrook and wallace13 who report a room-temperature tensile elongation of less than 1 pct. I) EXPERIMENTAL A) Sample Preparation. Experimental materials were prepared by directional solidification, by hot working, and by powder processing. The starting materials were electrolytic 99.9 pct pure cobalt and 99.99 pct pure aluminum. 1) Directional Solidification. A vertical Bridgman apparatus heated by induction was used to directionally solidify cylindrical ingots $ in. in diam and 5 in. long. The apparatus was first evacuated and then an argon atmosphere was introduced to retard evaporation. The ingots were contained in an alumina crucible inside a graphite susceptor that rested on a movable water-cooled base. The base was lowered out of the induction coil at a constant rate. Eight of the ingots were solidified using a drive rate of 2.5 cm per hr, two of the ingots at 1.2 cm per hr, and one ingot at 10 cm per hr. The eutectic composition Co 10 wt pct A1 was used in all but one ingot which had the composition of the stoichiometric CoAl intermetallic, Co 32 wt pct Al. 2) Mechanical Processing. At 1000°C the eutectic Co 10 wt pct A1 is a mixture of an intermetallic phase, Co 21 wt pct Al, and a cobalt-rich phase, Co 5 wt pct Al.10 These phases differ from the stoichiometric CO 32 wt pct A1 and pure cobalt because of the large solubility of this eutectic at elevated temperatures." Four rectangular slab ingots, 4 by 1 by 12 in. high, of Co 10 wt pct Al, Co 5 wt pct Al, Co 21 wt pct Al, and Co 32 wt pct A1 were cast for hot rolling. The cobalt was first vacuum-melted, H2-treated for 20 min,

Jan 1, 1968

By E. C. Rien

When the electrical system for a surface or open pit mine is designed, four major considerations should be satisfied in the following order: safety, reliability, flexibility, and cost. Careful planning initially will make expansion for future growth economical as well as possible without extended shutdown of operations. Electrical requirements in surface and open pit mining can be divided into three categories: main substation, plant power, and pit distribution. These systems are integral to each other, but will be dealt with separately here. 11.2-1. Main Substation. A main substation for a mining operation may vary from a 500 kva transformer supplying 480-v power to motor-driven pumps and conveyors, to a 50,000 kva substation serving a large beneficiation plant or a large strip mining operation. Regardless of size, it should be designed with the realization that a failure of the main substation will totally shut down the operation (Fig. 11.2-1.). Location of a main substation usually is a compromise between expense of running the incoming high-voltage transmission lines and the voltage drop of long secondary runs. Based on a geological survey for immediate and future areas of excavation, the main substation should be located as near to the center of load as possible. The site should be out of the blasting area, readily accessible to authorized personnel, and situated where prevailing winds will keep it free from dust or snow. DISCONNECTS AND OVERLOAD PROTECTION. The main substation should have a primary disconnecting device-either a pole top gang-operated switch and fuses of adequate interrupting capacity or, preferably, an oil circuit breaker with properly coordinated relay protection.

Jan 1, 1968

By Hans Strack

Electroluminescence of GaAs p-n junctions fabricated by simultaneous diffusion of sulfur and iron was investigated at 77°K. A narrow emission peak with a half width of about 4 kT in the energy range between 1.14 and 1.155 eu was attributed to iron. Other transition elements exhibited light emission in the vicinity of the iron peak, namely nickel between 1.15 and 1.16 ev and cobalt between 1.16 and 1.17 ev. The efficiency of the doping with iron depended on the amoz~nt of arsenic present. A weight ratio of arsenic to iron of 4:l was sufficient to observe the emission lines associated with transition elements. The presence of oxygen reduces the intensity of the light emission. In addition to the levels associated with transition elements, levels at 1.05 and 1.28 ev, probably due to lattice defects, are observed except in diodes fabricated in solution-grown GaAs. THE near band edge emission of GaAsp-n junctions has been studied extensively in the past.' GaAs devices utilizing spontaneous and stimulated near band edge emission are of considerable practical importance. Typical junctions are fabricated by diffusion of a heavily doped p region into degenerate n-type GaAs. Much less work has been done on investigating the radiative recombination via deep levels in lightly doped p-type material. This area is of interest in understanding the performance of GaAs n-p-n transistors. GaAs transistors show remarkable improvement in high-frequency performance and current-gain stability at high temperatures, when iron is added to sulfur during the emitter diffusion process. The present work was initiated to investigate deep-level electroluminescence of iron-doped GaAs p-n junctions fabricated on vapor-phase epitaxial GaAs and on solution-grown GaAs. For comparison several diodes doped with cobalt and nickel were studied. Iron, cobalt, and nickel have an electron configuration of the type

Jan 1, 1968

By G. R. Leverant

RECENT investigations1,2 of the low-cycle fatigue behavior of pure copper under strain cycling conditions have shown that a unique saturation stress level is eventually attained for each value of applied plastic strain amplitude. The dislocation substructure of copper at the saturation stress level is in the form of cells whose diameter decreases with increasing saturation stress level, i.e., plastic strain amplitude. In addition, both the saturation stress level and the cellular substructure are completely reversible. That is, the saturation stress level and accompanying cell size are determined solely by the present conditions of testing and are, therefore, independent of any previous cyclic history. The mechanical and substructural reversibility observed in pure copper, which has a relatively high stacking fault energy, is not observedz for Cu-7.5A1 which has a much lower stacking fault energy. This implies that easy cross slip (wavy slip) is a prerequisite for reversible fatigue behavior. A dispersion of fine, nondeformable particles of a second phase in a metal matrix tends to stabilize substruc- tures introduced by forming operations during subsequent elevated-temperature heat treatments.3 This raises the question as to whether a finely dispersed second phase can induce an element of irre-versibility into the cyclic deformation behavior of a wavy slip material at room temperature, due to partial stabilization of the initially introduced substructure. Since nickel has a higher stacking fault energy than copper,6 pure nickel should be characterized by cyclic reversibility. Therefore, TD-nickel* (Ni-2ThO.r) was

Jan 1, 1968

By K. A. Gschneidner, O. D. McMasters

DgIel-ential thermal, nretallographic, and X-ray paramzetric methods were used to establish the Yb-Pb phase dingram. The terminal solid solubilities in the system are less than 0.2 at. pct. Lead additions lower the 792°C transformation tewzperature of pure ytterbiun~ at 787°C by means of an inverted peritectic veaction. Ytterbium additions raise the 327oC melting point of lead to 329°C by means of a perilectic reaction. Three intermetallic compounds Yb2Pb, YbPb, and YbPb, melt congruerttly at 1246", 1116o, and 740°C. respectively. YbsPb3 forms by a peritectic reacliorz at 1250°C. YbzPb crystallizes in the PbCh (C23) type structure and the orthorhombic latliceo constants are a, = 7.478. bo = 5.225, aud C0 = 9.549A. YbsPbs crystallizes in the hfnsSi3 (D8a) type structure. The hexa~nal lattice constants for this phase are a, = 9.325 and co = 6.92d. YbPbl crystallizes in the cubic AuCU3 (Ll2) type structure with a: = 4.8628 + 0.0008A. YbPb is diwrorphic with the structure change occurring al 507°C upon healing. The crystal structures of the two forttzs were not determined. Eulectic reactions occur at 5.1 at. pct Pb and 769oC, 41.5 at. pct Pb and 1086oC, and G8.0 at. pct Ph and 717°C: RELIABLE information concerning the alloying behavior of most of the rare-earth metals is scarce. A systematic study of the rare earth-lead alloy systems now in progress is an effort to supply such information. Determination of the phase diagram of the Yb-Pb alloys is the first step of this study. Variations in the valence of normally divalent ytterbium may be studied by comparing the characteristics of the Yb-Pb alloys to those of the trivalent rare earth-lead and of the divalent alkaline-earth-lead systems. Of particular interest are the melting temperatures of the intermetal-lic compounds since these are known to be high relative to the melting points of the constituent metals. Crys-tallographic and magnetic susceptibility data for the rare earth-lead alloys are to be included in the comparative study. Results from this and subsequent investigations should provide a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The major impurities in the ytterbium and lead used in this investigation are listed in Table I. The lead was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The ytterbium was prepared in this laboratory by the lanthanum reduction of the oxide followed by a distillation of the ytterbium. Alloy Preparation. The alloys were prepared by

Jan 1, 1968

By C. M. Mason

The current Bureau of Mines active list of permissible explosives includes 95 brands. Twelve are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1968

By A. P. Woods, J. A. Elias, A. J. Heckler

A method is described by whichX-ray pole figures and axis density figures may be plotted automatically. The X-ray data are obtained using a Siemens texture gonionleter and the Schulz reflection method. Composite sampling methods are used to obtain a full quadrant of the pole figure. The contour lines of the pole figure and axis density figures are drawn using a computer-controlled x-y plotter. The computer program used to draw the contours was obtained from ZBM. POLE figures used to describe crystallographic orientations of poly crystalline sheet materials are usually plotted manually from X-ray diffraction output in the form of a strip chart recording of the intensity distribution of a given crystallographic pole in physical space. Today's computers and associated plotting equipment now make it possible to plot pole figures and axis density figures automatically. Inverse pole figures have been determined by mathematically "inverting" X-ray pole figure data.'-' In general, these methods require complicated, time-consuming numerical calculations. A more economical but less accurate method is to determine the axis densities of low-index crystallographic poles using an X-ray diffractometer. When these axis densities are plotted in a unit stereographic triangle contour lines can be drawn to represent the axis density distribution. This can now be done automatically. Computers were used to plot pole figures by a method developed by Holland, Engler, and powers.' In their method intensity ratios based on a random standard sample were obtained from a strip chart recording, and the stereographic (x, y) coordinates of these ratios were determined by a computer. Symbols characteristic of different intensity ratio levels were then plotted using an automatic x, y plotter and intensity contours were drawn manually. The present paper describes a method by which pole figures and axis density figures have been automatically plotted from digital data obtained from a Siemens X-ray unit. Plotting was accomplished using an IBM 1620 computer and a Calcomp 563 digital plotter. COMPUTER PROGRAM The computer program was obtained from IBM Systems Reference Library, No. 1620-CS-05X, and was designed to plot contour maps from randomly distributed data. It consists of a set of twelve separate subprograms, four of which were used in this work. The program takes a given distribution of data points and by a numerical method determines the values at mesh points of a square grid system superimposed over the input data. The output data from this program is in a form suitable for input to the contour plotting program. A smoothing program is also available which calculates new mesh point values from a continuous function fitted to neighboring mesh points. The degree of smoothing depends on the number of points around a given grid point which are used to adjust or smooth the grid value. The contour plotting program is designed to allow the user to specify the interval, scale, and annotation of the contours to be plotted. EXPERIMENTAL PROCEDURE Pole Figure Data Points. Diffracted X-ray intensities were determined using a Siemens texture goniometer and the schulzs reflection method. Due to geometric

Jan 1, 1968

By Wido Tilmann

13.6-1. Importance. In Germany there are large tertiary brown coal reserves, most of which are located close to the surface. Therefore, brown coal has been recovered for many years by means of opencast methods. By utilizing a high degree of technology, a rational operation has been achieved, and as a result, the mining techniques have become renowned all over the world. After the war, all the dredgers and overburden spreaders, as well as the means of conveyance, had to be redeveloped for adapting this equipment to the changing conditions of the deposits. Numerous auxiliary machines were adopted from the American earth moving industry and altered according to the different requirements. As a result of such technical developments, the output per man and per shift was increased remarkably in spite of the deterioration of the geological conditions. In the whole of Germany, the total reserves of brown coal amount to 100 billion metric tons, of which 60 billion tons are situated in the Federal Republic of Germany. In the latter area, 8.5 billion tons will be recover- able by opencast means, of which 3.5 billion tons are already developed. The annual output reached 102 million tons in 1965. This total figure comes from four different mining districts: Rhineland, Helmstedt (town at the border of the Soviet occupied zone), Hesse, and Bavaria. The production figures (1965) are as follows: [ ]

Jan 1, 1968

By Robert H. Merrill

In 1960, the Kennecott Copper Corp. and the U.S. Bureau of Mines entered into a joint research program to determine the changes in stress, strain, and displacement created by changes in slope angles. The field site was the Kimbley Pit, located near Ely, Nevada; the supporting laboratory investigations were made at the Bureau's Denver Mining Research Center. Following a study to determine the rock stresses in the mining district, the strike and dip of geologic defects (fractures) in the rock, and the laboratory-determined strength of the rock, a new slope angle and pit configuration was selected, and instruments were installed to measure changes in stress, strain, displacement, microseismic noise rate, and sonic velocities at several points in the west wall of the pit. Between February and November 1966, the west slope was changed from an average angle of 45° to a new slope angle that started at 45° on the south wall, gradually increased to 57 ½ at the center of the west wall, and to 61° on the north wall. The pit was deepened from about 500 feet to about 550 feet. About 2.55 million tons of waste and ore were removed by stripping and mining.

Jan 1, 1968

By Robert M. Becker

The evaluation of in situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated.

Jan 1, 1968