Search Documents

By W. A. MacDonald, C. M. McGibbon, J. H. Reynolds

This paper traces the development of the Seaboard Power Plant, which plays such an important role in the industrial life of Nova Scotia. It also shows the involvement of the plant in the siting of a heavy water production facility in Cape Breton. The paper concludes with an outline of the new installations which the Nova Scotia Power Commission has undertaken as an extension to the Seaboard Plant.

Jan 1, 1966

By George E. Aiken

Modern high speed bucket wheel excavators (BWEs) can dig materials which power shovels can't handle without blasting. Yet these machines are not used in any large, open pit ore mines in the United States. American mining has been slow to use the wheel's special capabilities of high production volume at low cost, due perhaps to a traditional familiarity with shovels and draglines and/or the lack of data of BWE operation, design and cost. Of course, shovels and draglines can not be replaced by BWEs in all cases, but under suitable conditions bucket wheels can out-perform other conventional excavators and simultaneously permit significant operating savings. The latter aspect will become increasingly important to American mining men because as more low to medium grade orebodies are found in regions of thick overburden, better and cheaper ways of uncovering them must be developed. Typical of such areas are the thick alluvial fans of the Southwest and the glacial drift areas in northern regions. Much of this material would handle well with a wheel excavator without blasting, although ripping might be necessary in some cases.

Jan 1, 1966

By F. F. Craig

Many full-scale waterflooding operations are preceded by pilot floods, one purpose of which is to provide an estimate of recoverable oil. A laboratory model study was made to determine the influence of the producing wells' effective productivity on the oil recovery efficiency of single five-spot pilots, as well as single injection well pilot floods. The effective productivity is indicated by the value of Condition Ratio, defined as the actual well productivity to that of on undamaged and non-stimulated, normal-sized well in the same formation. The effects of initial gas satrcration and mubility ratio on recovery eficiency were also investigated in this model study. Model test results skowed that at favorable mobiliry ratios, a five-spot pilot flood can provide a direct quantitative estimate of the recoverable oil in the pilot area. If the pilot producer's Candition Ratio is 2.2 or more, upwards of 90 per cent of the recoverable oil in the pilot area is recovered from the inside producer, regqrdless of the mobility ratio or initial gas saturation. This Condition Ratio can be achieved with preyent fracturing techniques. Model studies also showed that over the range of imposed injection pressure differences and regional pressure gradients normally encountered in field operations, there was no effect on the recovery efficiency of a five-spot pilot waterflood. Model studies of single injection well pilot waterfloods showed that with no initial gas saturation, the total oil recovery at the offset producing wells can indicate the oil recovery possible by full-scale waterflooding. It is essential that the Condition Ratios of the offset wells be above 1.4. If an initial gas saturation exists prior to water injection, the recoverable oil cannot be directly evaluated by a single injection well pilot flood. However, the production per formance of such a flood can be used to provide information on volumetric sweep efficiency. INTRODUCTION Oil reservoirs are conlplex structures and cannot always be fully studied in the laboratory. Therefore, many operators consider it prudent to evaluate a waterflood prospect by means of a pilot flood. Pilot waterfloods generally involve one of two well arrangements: a single five-spot pilot waterflood, involving four injectors and an internal pilot producing well; and a single injection well pilot flood (sometimes called an inverted five-spot pilot) having one injector and four sur- rounding pilot producers. Some pilot floods are composed of multiple five-spot pilot patterns. To yield information applicable to field-wide performance, the pilot must be located in a representative portion of the reservoir. Pilot floods generally are conducted for one or more of the following reasons: (1) to determine whether water could be injected at desirably high rates, (2) to determine whether an oil bank or zone of increased oil saturation is formed by water injection, and (3) to estimate the oil recovery by waterflooding. Many of the early pilot water-floods were conducted for only the first two reasons. As soon as a buzz in oil production was obtained in the pilot, water injection was initiated throughout the entire lease or field. A number ot laboratory studies have been directed toward determining conditions under which a pilot flood could yield a quantitative estimate of the oil recovery possible by full-scale pattern flooding. One of the early studies of single five-spot pilot flooding' showed that well damage to the inside pilot producer could reduce the total amount of oil recovered. In a study of the single injection well pilot flood pattern,' the results indicated that if the model boundaries were no closer than a half-well spacing beyond the pilot pattern, the pilot performance in the laboratory is unaffected by these boundaries. In another study,? he effect of initial gas saturation and mobility ratio on the ratio of production to injection rate for various groupings of five-spot patterns was defined by mathematical and analog methods. In a study4 involving both potentiometric and flow model experiments at a mobiliry ratio of unity, four different pilot patterns were studied. These included a single five-spot, a single injection well pilot, a cluster of four single injection well pilots and six inverted five-spots. In this study the ratio of well diameter to the distance between injection and producing wells was held constant at 1:1000. The effect of the 7 ratio-—the ratio of the pressure drawdown at the producing wells to the pressure build-up at the injection wells on the pilot performance-was studied. The values of 7 ratio ranged from 0 to 0.34. Results showed that both the total oil recovery and the total fluid production from the pilot relative to the cumulative injection increased with increasing values of the 7 ratio. The effect of both the ratio of injection to producing rates and mobility ratio on the oil recovery performance of a liquid-saturated single five-spot pilot flood was studied in a series of flow model tests.5 Rate ratios ranged from one to four, and mobility rates ranged from 0.1 to 10. Resulls of these tests showed that at low rate ratios, the pilot producers may recover up to four times the recover-

Jan 1, 1966

By A. M. Sarem, J. M. Campbell

Molecular refraction is introduced as a new and improved third parameter for prediction of the PVT behavior of hydrocarbon systems. This parameter, characterizing the complex as well as the pure hydrocarbon systems (1) is a direct measure of London dispersion forces which affect the PVT behavior; (2) can be measured directly, accurately and easily for complex as well as pure hydrocarbon systems; (3) varies significantly between the reference substances thus allowing accurate interpolation of PVT properties; and (4) has a fundamentally sound basis. Molal average molecular refraction was used with the pseudocritical mixing rule proposed by Leland and Mueller to predict the molal volume of liquid and vapor for 84 published data points on nC4-nCI0, Cl-nC5, Cl-nC4-nC10 systems in the region of coexisting vapor-liquid and at the critical point. The same technique was applied to predict the densities of liquid hydrocarbon mixtures in the two-phase and single-phase regions near the critical point for seven different systems each having different properties of the heptanes-plus fraction, but all simulating the fluids of either gas-condensate or volatile oil reservoirs. A modification of the Leland-Mueller mixing rule for the determination of pseudocritical properties is also presented which yields more accurate liquid density predictions than the original form when used with the proposed third parameter. INTRODUCTION The PVT behavior of multicomponent systems has received widespread attention in the literature in recent years. A large portion of the reported work has stemmed from attempts to overcome the inherent difficulties encountered when using the standard compressibility-factor chart which shows 2 as a function of reduced temperature T, and and reduced pressure p,. This chart assumes that z, is constant for all systems. The error in this assumption is not pronounced for pipeline-type gases high in methane and low in heavy ends, particularly when contained at moderate pressures. For such gases the error in the calculated z is usually less than 2 to 3 per cent. However, the reliability of this approach becomes somewhat nebulous for gas condensate and volatile oil systems at high pressure. One logical approach has been to recognize the variation of 2,. This idea was first suggested by Meissner and Seferianl and used by Lyderson, Greenkorn and Hougen2 to prepare extensive tables of thermodynamic properties. Other third parameters have been proposed by Stockmeyer, Kihara, Riedel, Lightfoot, Bloomer and Pitzer. These were tested by Satter and Campbel13 for many gas mixtures and it was shown that they were inter-related. All of these third parameters have a common fault — they cannot be directly evaluated for the heptanes-plus fraction. Consequently, one necessary requisite of an improved method for predicting the density of multicomponent hydrocarbon systems, was development of a third parameter that could be evaluated for that fraction. PREVIOUS MULTICOMPONENT DENSITY PREDICTION METHODS Sage and Lacey4 suggested a method of using partial molal volumes for computing the density of hydrocarbon gas mixture for pressures to 3,000 psi. In this technique, they approximate the complex multicomponent gaseous mixtures by a quarternary system of methane, ethane, propane and butane. Sage, Hicks and Lacey5 suggest a method of using partial molal volumes for computing the density of hydrocarbon liquids. The results agree within 3 per cent of the experimental values. However, the composition range is limited to about 10 per cent by weight of methane. Consequently, this correlation does not cover the low-molecular-weight liquid similar to natural gasoline and high-pressure gas condensates.

Jan 1, 1966

By C. H. Hewitt, J. T. Morgan

The Fry cocurrent in situ combustion project was carried out in a 3.3-acre portion of a lenticular body of Robinson sandstone of Lower Pennsylvanian age. This particular sand body is about 12,000 ft long and 3,500 ft wide; it varies in thickness from 0 to 55 ft, trends northeast-southwest, and occurs at depths between 880 and 936 ft. The reservoir is made lip of three distinct types of sandstone, each having characteristic reservoir properties. (See Table I.) Textural gradients, sedimentary structures, erosional basal contact, absence of marine fossils, and geometry of the sand body all indicate that the sandstone is of fluvial origin and part of an extensive complex of river-deposited sedirnents. Geographically oriented cores reveal that the direction of depositing currents was to the southwest, parallel with the sand-body trend. Directions of maximum pernleability also parallel the northeast-southwest trend. The layered nature of the sandstone reservoir and its directional properties have controlled the areal distribution of produced gas, the ignition behavior, and the vertical profile and horizontal extent of the conbustion zone. INTRODUCTION This paper is the first of a series of three papers that describe Marathon Oil Co.'s Fry in situ combustion test. This first paper contains the results of a detailed study of the geology and reservoir characteristics of the Robinson sandstone reservoir in which the Fry test was conducted. The second and third parts of this series report on the field operations' and performance. The geologic work reiated to cores cut through the combustion zone, and to the effect of reservoir properties on the combustion process is included in the third paper.' GEOLOGIC STUDY OF THE FRY RESERVOIR The close spacing of continuous cores in the Fry combustion site provided an unusual opportunity to study the details of distribution of lithology and reservoir properties within a petroleum reservoir. The objectives of the study were: 1. To determine the distribution of rock types within the Robinson sandstone in the Fry area; 2. To determine the relationship of porosity and permeability to rock properties and establish the distribution and homogeneity of reservoir properties; 3. To determine the origin of the Robinson reservoirs so that attempts could be made to predict the size, shape, distribution, extent and continuity of Robinson reservoirs; and 4. To determine what effects, if any, the reservoir rocks might have on the combustion process, so that the process might be better evaluated. AVAILABLE MATERIALS Continuous cores were cut from 14 wells in the vicinity of the Fry site. Ten of the cores are from within the 3.3-acre pattern; six of the 10 were cut prior to combustion, and four were cut through the combustion zone. Cores from the Emma Fry No. 15, Wampler 0-2 and Fry B wells (Figs. 1, 2 and 9) were geographically oriented by the Eastman Oil Well Survey Co. Maps, electric

Jan 1, 1966

By Bernard Porter

The densities of LiF, NaF, and KF, of binary mixtures of these alkali fluorides, and of binary mixtures of UF4, ThF4, YF3, LaF3, and CeF with each of tie alkali fluorides were measured as functions of the melt composition and temperature. Molar volumes at 1,000° C were calculated for all the mixtures. Binary systems containing LiF exhibited molar volume ideality. Binary fluoride systems containing either NaF or KF as the alkali fluoride exhibit positive deviations from molar volume additivity. However, molar volumes in the NaF-KF system are ideal.

Jan 1, 1966

By Thomas M. Ware

"MR. Chairman, our Honourable Minister, Mayor Cole, it is a pleasure for me to come here, and join with you in one of the largest industrial shows ever held in Saskatchewan.It is an honour to be asked to keynote your meeting, to help mark an early chapter of this new industry for Saskatchewan. God has placed in our hands a new resource for His man on earth. This store of potash, 350 million years in the making, offers a vital resource to help man support his advanced intellect for thousands of years. It is a gift so large we must all wonder at its purpose and our responsibilities in serving our fellow man with it.We who are here to plan and implement the development of this essential mineral resource enjoy a great -privilege; and we share a great responsibility -to see that the billions of tons of potash which have waited beneath these prairies for millions of years are widely and wisely used to nourish the earth through future millenniums.To know the true value of potash, to be able to bring forth this re-source from over 3,000 feet deep in the earth, to establish markets and develop its potential worldwide is all part of our great heritage from generations past. So I think it is fitting on this occasion that we reflect for a moment on this heritage, to help us assess the responsibilities of its future development."

Jan 1, 1966

By E. J. Kloos

The Bureau of Mines evaluated all previously approved gas masks to determine their ability to provide respiratory protection against each of the following six selected amines: ethylenediamine, diethylamine, n-butylamine, ethylamine, methylamine, and hydrazine. Minimum requirements were a 24-minute service life at a flow rate of 64 liters per minute (32 liters per minute for hydrazine) and an amine concentration of 1.0 volume-percent (0.5 volume- percent for hydrazine). The three masks meeting these requirements were the LG4, Willson Products Division, The Electric Storage Battery Co.; the GMD-SS, Mine Safety Appliances Co.; and the 084-PHOV-R, Acme Protection Equipment Co.

Jan 1, 1966

A genesis based on new developments in the physical chemistry and flow properties of colloidal substances is proposed for the pipe-like Peko orebody. The rheological behaviour of sediments is governed by the contained colloids. Remobilization of thick pasty sediment during diagenesis is regarded as an essential step in the concentration of metal dispersed in sediments. At a high concentration the sediment pore fluid is a dense gelloid such that van der Waals attractive forces between the colloidal particles exceeds the coulombic repulsion. This permits accretion of the colloids into globular clots and their fracture fragments. These have a uniform size distribution dependent upon the rate of shear, and the sediment lithifies to clotted, porphyry-like, "gritty", dolomitic or igneous-looking intrusions and flows. The physical chemical properties of natural sediment colloids appear adequate to account for ore formation.Adsorption accounts for the dispersion and retention of metal in sediments. Accretion accounts for the segregation of the colloidal materials to give the various types of clotted igneous-looking intrusive source rocks. Syneresis enables the colloids to spontaneously draw together and to dehydrate. Formation of an ordered lattice achieves a lower energy state and desorbs metals and insoluble metal compounds "particle by particle" into the escaping water of hydration and pore water. Peptization enables migration of the metal hydrosols as stable dispersions until they merge for outflow through seepage zones or water extrusion channels. Nucleation and concretion precipitate the metal dispersoids from pore waters seeping through hydrous parts of the source rock, porous beds, faults, and zones of weakness by which the connate waters leave the lithifying sediments. Gelatinous precipitated mineral matter in the ore channels is capable of thixotropic reliquefaction when disturbed by shock or movement. Local reintrusion, flowage, interveinings,brecciation, and intermixing of the materials is the result.The principles of the suggested genesis are applicable to both syngenetic and epigenetic mineral accumulations.

Jan 1, 1966

By W. C. Maurer

A study of the mechanics of shear failure of rock under pressure has been made. The transition from brittle to ductile failure occurs when the friction along the fracture surfaces exceeds the shear strength of the rock. A machine has been developed for measuring both the shear strength of rock and the friction along rock fracture surfaces. In this shear machine, the fractures are forced along definite planes; as a result, the rock is stronger than in compression tests where the fractures choose the weakest paths through the specimens. Friction is composed of several forces: (1) the forces to slide irregulurities on surfaces over each other; (2) forces to shear some of these irregularities; (3) molecular attractions across the fractures; and (4) forces required to break bonds resulting from melting and welding at the tips of irregularities on the surfaces. Friction along rock fracture surfaces is not proportional to contact pressure as usually assumed; instead, it increases as the contact pressure raised to the 0.4 to 0.8 power. INTRODUCTION It is difficult to produce tensile stresses under the high compressive stresses present in the earth; therefore, in deep drilling and geological faulting, shear failure predominates. This shear failure mechanism is complicated because rock is a heterogeneous material containing pore spaces, microfractures, elastic discontinuities and other imperfections. A study of shear failure of rock under pressure has been made to obtain a better understanding of this complex mechanism. A machine has been developed and used to measure the shear strength of rock and friction along sheared surfaces. This machine has certain advantages over the compression test — shear properties can be measured under low normal stresses and shear stress and normal stress can be varied independently. The first part of this paper is a description of shear failure of rock under pressure. The role of shear strength and friction along fracture surfaces in the shear failure mechanism will be discussed. The second part consists of a description of the shear machine and a discussion of the shear strength and friction data obtained using this machine. It will be shown that shear strength depends upon the size of the stressed zone, and that friction does not increase linearly with contact pressure as usually assumed. Attempts are made to relate some of the new concepts to tectonic failure and to dril ling. SHEAR FAILURE IN ROCK TRIAXIAL TESTS The shear failure mechanism is illustrated by the triaxial test shown in Fig. 1. In this test, a cylindrical rock specimen is subjected to a confining pressure, PC, and an axial pressure, pa. These external pressures produce normal a and shear T stresses on inclined planes within the specimen equal to1 where 0 is the angle between the specimen axis and a normal to the inclined plane. Fig. 2 shows how triaxial specimens deform as the axial pressure is increased. The pressure is

Jan 1, 1966

By B. N. Nandi

This paper is a study of the application of the science of coal petrology to the use of coal in the iron and steel industry. The petrography of coal is given the most attention, with some mention of coal palynology. The history of the petrographical analysis of coal is first out-lined, with a description of the various coal entities, and then the apparatus and experimental techniques employed for coal evaluation are discussed. The coke stability factor and the relation of coke strength to petrographical data are also covered, and some space is given to the new science of coke microscopy, in particular its use in following the oxidation of coals.

Jan 1, 1966

By I. L. Nichols

Volatilization of cesium from pollucite ore was investigated as an initial step in the production of purified cesium metal or cesium salts. High recovery of cesium and rubidium as chloride sublimates was accomplished by 2-hour roasts in a tube furnace using charges containing 1 part ore, 2 parts limestone, and 0.23 part calcium chloride. Recoveries of cesium in the sublimate product were 89.1, 92.9, and 95.2 pct, respectively, using 1,100° C and vacuum, 1,250° C with an air sweep, and 1,250° C without an air sweep. Most of the lithium, sodium, and potassium sublimed with the cesium and rubidium, but virtually none of the calcium, aluminum, and silicon in the charges was volatilized.

Jan 1, 1966

By Robert K. Koch

The Bureau of Mines investigated separating HF from HF-SiF4-H2O mixtures by passing the mixed gases through a sodium fluoride slurry in an airlift scrubber and forming a mixed precipitate of NaHF2 and Na2SiF6. The oven-dried precipitate was thermally dissociated in two stages. The first stage was carried out at 400° C and dissociated NaHF2 to NaF and HF. Condensation and analysis of the evolved HF proved it to be 97 to 99 weight-percent HF containing 0.79 to 0.99 weight-percent H2O and 10 to 93 ppm silicon. The second stage was carried out at 700° C and dissociated Na2SiF6 to NaF (for recycle) and SiF4. The quantity of HF recovered from gaseous HF-H2O-air mixtures decreased with increasing relative H2O concentrations. Air was beneficial when scrubbing extremely dilute wet HF gases. At HF partial pressures of 0.24 and 0.013 mm Hg in the scrubber entrance gases, HF partial pressures of 6.2 x 10-4 and 9 x 10-6 mm Hg were obtained, respectively, in the scrubber exit gases. Scrubber efficiencies were 99.7 and 99.3 percent.

Jan 1, 1966

Jan 1, 1966

By George H. Holmes

The water situation in Nevada mineral and related industries is described in this report. It contains information on the sources and adequacy of supply to current operators, requirements and uses, quality and costs, geography, hydrography, precipitation and evaporation characteristics, and Nevada water laws. Also, information is given on the water requirements of one public utility powerplant, and the source and consumption of water in four major cities. Water distribution at 24 operations is shown on schematic waterflow diagrams. The mineral industries of Nevada in 1962 used 8.6 billion gallons of new' water and reused 3.8 billion gallons for a total usage of 12.4 billion gallons. The copper industry was the major water user. The 1962 value of all mineral production in Nevada was $85.5 million. The large amount of water required to maintain thin high production is obtained principally from ground-water sources in alluvial valleys and the permeable rock formations of some mountain ranges. Some water is also obtained from perennial streams and springs. Sources of water utilized by existing industry ire near most mineral industry operations; however, seven companies are forced to pipe water distances ranging from 2 to 8 miles. Although water supplies of presently operating companies are adequate at most operations, several companies resort to large-scale reuse of water as a matter of conservation and economics. Acquisition of water by new operators is possible but takes considerable negotiation. Water rights, surface and underground, are controlled by the State. The quality of the water is satisfactory for most purposes. Analyses of 19 samples, listed in the appendix, show the range in water quality at various plants throughout the State. Costs of delivering new water to current operations range from 2 to 26 cents per 1,000 gallons with an average of 10 cents per 1,000 gallons for power and maintenance. No firm costs for recirculating water were available; estimated costs range from 1.5 to 2.5 cents per 1,000 gallons. The mineral-product value of the entire Nevada mineral industry in 1962 was equivalent to $10 per 1,000 gallons of new water and $26 per 1,000 gallons consumed. Projection of the 1962 water requirements of the Nevada mineral industry indicates that the demand For new water will increase from 8.6 billion gallons in 1962 to 11.9 billion gallons in 1980, a 43-percent increase. Water requirements in the year 2000 are estimated as 14.8 billion gallons, an increase over 1962 water demand of 78-percent.

Jan 1, 1966

By James S. Browning

The principal uses of fine ground mica are as filler in wallboard joint cement, as a filler and surface coating for roofing, as an ingredient in paints, and in oil well drilling mud. The mineral has other uses in the manufacture of rubber, wallpaper, plastics, welding rods, electric insulation, house insulation, and textiles, and as an annealing agent in metal treatment. In recent years, more than 999 percent of the domestic mica produced has been scrap and flake mica (mica which does not meet specifications for sheet mica and is used for producing fine ground mica). There has been a continued increase in mica production for, several years, the 1963 production of scrap and flake mica totaling 117,251 tons.

Jan 1, 1966

By J. M. Kuchta

The Bureau of Mines used laminar hot air jets of l/8- to 3/4-inch diam-eter to determine the hot gas ignition temperatures of various combustible vapor-air mixtures. The combustibles were n-hexane, n-octane, n-decane, a hydrocarbon jet fuel (JP-6), and an adipate ester aircraft engine oil (MIL-L- 7808). Minimum ignition temperatures occurred at a fuel to air weight ratio of about 0.5 and were not greatly sensitive to variations of fuel concentra¬tion. Moderate variations of jet velocity also had little influence on these ignition temperatures. However, these temperatures decreased with increase in heat source dimensions (jet diameter). The hot gas ignition temperatures of the combustibles were not necessarily much greater than corresponding autoignition and wire ignition temperatures when the size (,F the heat source and the ignition criterion were the same.

Jan 1, 1966

By J. M. B. Scarborough

This paper deals with measures taken to maintain effective operation of heavy-duty equipment in open-pit mining. at Pine Point, N.W.T., during periods of extreme cold weather. The points covered include equipment modifications designed to improve cold-weather performance, effective lubrication of machinery that is vulnerable to extreme cold and operating procedures designed to prevent equipment damage.

Jan 1, 1966

By James E. Hill

Tremendous improvements in mining technology have been witnessed during the past 100 years. For example, before 1860 all blastholes were drilled manually and blasting was done with low-energy black-powder. During the 1860's both the pneumatic rock drill and high-energy dynamite were introduced, ushering in an era of mining mechanization that has steadily progressed since that time. Today, with the rapid implementation of the latest advances in communication science, mining technology is moving into a new era that goes beyond mechanization as such. Transistors, transducers, scanners, telemetry, and the like, all terms largely derived from the new communication sciences, add up to what is popularly know as automation-the communication of machine with machine. Automation is now playing an important role in selected parts of the mining process, such as hoisting, hydraulic roof supports, and underground surface locomotive haulage and belt conveyor systems. But this year marked the first attempt to auto-mate the total mining process with the commencement of production at the British National Coal Boards Bevercotes mine. If this full-scale experiment proves successful, it could lead towards other fully automated mines in both Britain and other parts of the world. This decade, there-fore, could be considered the one that provided the foundation for the mines of the future.

Jan 1, 1966

By Verne E. Hooker

The Bureau of Mines conducted a preliminary investigation to determine the state of stress in crystalline rock outcrops near Atlanta, Ga. The secondary principal stresses in a horizontal plane near the surface are compressive and are 500 to 3,000 psi. The maximum compressive stress is northeast-southwest in the Stone Mountain-Lithonia district but changes to northwest-southeast near Douglasville. The elastic constants were determined from data obtained by static and dynamic laboratory methods and in situ velocity measurements. Results show Young's modulus to be dependent upon both stress level and anisotropy in the rock. Average secant moduli obtained from triaxial tests were used to compute the applied stress from borehole deformation measurements.

Jan 1, 1966