Search Documents

By Robert M. Doerr

The oxidation kinetics of Ni-Y alloys in the range 0.04 to 8 weight-percent Y, and of high-purity Ni, were compared by the use of a sensitive volumetric apparatus. The reactions followed approximately the parabolic rate law; for oxidations in 02 at 0.5 atm and 1,200° C, the parabolic rate constant was about 0.37 + (0.064) (Y-2.11) mg cm-2 min-1/2, where Y represents the weight-percent Y in the alloy. Internal oxidation of Y occurred in the alloy specimens and the resultant Y203 particles, which were in patterns related to the eutectic structure of the alloys, served as markers showing that the subsequent oxidation of the surrounding Ni was by inward diffusion of O. The scale consisted in each case of NiO, but the inner parts of the scale on the alloy specimens included the patterned Y203 particles. The thicknesses of the inner parts of the scale depended directly on the Y concentration, and the thicknesses of the Y2O3-free outer parts of the scale were inversely related to the Y content of the alloys. There is thus a relationship between the thickness of the outer part of the scale and the protectivity of the scale. Outward diffusion of Ni and inward movement of 0, from the inner boundary of the Y2O3-free part of the scale, is proposed as a mechanism for these results.

Jan 1, 1966

By James Paone

The Bureau of Mines made drillability studies with impregnated diamond bits in the laboratory on 7 rock types and in the field on 21 different rock types. Results indicate that drill parameters of rotational speed, thrust, and torque must produce sufficient applied forces to induce stress levels that cause continuous failure in rock to achieve efficient penetration rates. Higher rotational speeds appear to be more effective in drilling relatively harder rocks, although the increased speed causes more bit wear; increases in thrust result in higher drilling rates but not linearly; and up to a critical value a linear relation exists between torque and penetration rate for a specific rock type. Penetration rates with impregnated bits show a trend similar to that obtained with surface-set bits for rock under 25,000 psi compressive strength.

Jan 1, 1966

By Frank B. Fulkerson

A study was made of scrap iron and steel in the South Central States in order to determine trends in processing, shipment, and consumption of this important commodity. These data were derived in part from statistical sources and in part by visits to scrap yards and steel mills. Trends in the industry were reviewed. Dealers in 1963 supplied 1.8 million tons of iron and steel scrap to steel mills and foundries in the south-central area, compared with 2.1 million tons in 1955. Most of the scrap was processed and shipped within 200 to 300 miles of consuming centers. Exports provide a principal outlet for dealers along the gulf coast. Most of the scrap that fills these orders is loaded onto freight cars at yards in Texas and Louisiana and -is shipped to ports for direct transfer from railroad car to ship. The tonnage exported varies greatly from year to year. The largest scrap operations are in or near large cities which are heavy scrap generating areas, steel mill sites, or port cities for export of scrap. A tentative analysis indicates that the short-run supply of prepared scrap is inelastic to price changes; therefore, buyers probably arc in a strong bargaining position at times of declining demand. One technological development in the iron and steel scrap industry is the use of large presses which can take complete automobiles with frames, wheels, springs, and other heavy parts still intact and reduce them to bundles. At Houston, Tex., and Kansas City, Mo., shredding plants are in operation that reduce car bodies and other light scrap into flat pieces 4 to 6 inches in size.

Jan 1, 1966

By R. L. Benner

A compound stability diagram was constructed by the Bureau of Mines for the Zn-Fe-S-O system to show the phases that should be thermodynamically stable at various temperatures, oxygen pressures, and SO2 pressures. The diagram was demonstrated to have good qualitative value for predicting stable phases that may, in turn, be related to the recovery of zinc in the leaching phase of the electrolytic zinc process. The study showed that roasting temperature is the most Significant variable in preventing roaster formation of zinc ferrite, which is directly related to subsequent extraction of zinc in the leaching step.

Jan 1, 1966

By E. A. Loria

High-quality sheet of electrowon molybdenum was attained by a sequence of procedure on pressed and arc-melted crystalline powders. The procedures included high-temperature, high-vacuum sintering treatments and the use of metal deoxidizers instead of carbon to improve the mechanical properties of the molybdenum sheet. Rolled sheet 60 mils thick was evaluated by tensile and bend tests, hardness measurements, microstructures, and recrystallization treatments. After stress relieving, yield strength ranged from 85,000 to 110,500 psi (0.2- percent offset) and ultimate strength ranged from 87,200 to 117,250 psi with 4.5- to 25-percent elongation observed for arc-melted sheet, and 5.0- to 23- percent elongation observed for powder metallurgy sheet. In room temperature bend tests the sheet yielded plastically, indicating that the ductile-brittle transition point was below room temperature. The diamond pyramid hardness (DPH) of the molybdenum sheet changed from 214 to 293 DPH for the stress-relieved condition to 177 to 185 DPH for the fully recrystallized condition. The brittleness of recrystallized molybdenum, reported by other investigators as characteristic of sheet prepared from commercial-grade hydrogen-reduced powders, was not in evidence. Recrystallized tensile specimens pulled at room temperature had an average elongation of 31 percent.

Jan 1, 1966

By Jr. Hazen

This report documents 653 sets of sample data involving 78,366 assays obtained from past exploration for various minerals and metals. Most of these data have been taken from published reports describing exploration projects, conducted jointly by the Bureau of Mines and the Geological Survey, for the Strategic Minerals Program from 1940 through 1949. Means and standard deviations have been computed for the exploration assay data and have been plotted on graphs for 22 minerals and metals. A mathematical model, based on the binomial distribution, has been developed to explain the configuration of the plots of the exploration means and standard deviations. The two statistics, mean and standard deviation, which describe assay data, have been used for simulating probability models. These probability models then have been combined with the binomial model of the exploration assays and related to the sequential decision process associated with exploration drilling for mineral deposits. These probability regions can be used to form the basis for sequentially predicting the probable range of the average grade of mineral or metal that may be expected as an exploration drilling program is continued after the initial discovery of mineralization has been made.

Jan 1, 1966

By Jean-Louis Robert

Field work inaugurated in 1962 in the townships of Lemieux and Lesseps, in the Gaspe Peninsula of Quebec, has permitted the author to delineate the lithologic units of the area, to elucidate a few stratigraphic problems and to outline several zones of alteration. Certain features of these zones and the numerous mineralized showings in the area merit the attention of prospectors and exploration companies.

Jan 1, 1966

By Lester G. Morrell

THE WORLDWIDE economic expansion that has characterized the first 3 years of the 1960's continued through 1964 and was reflected in North America by strength in the industrial economy of the United States, which again was dominant. Advances in production were recorded in virtually all industries, including the mineral industry; 1964 mineral production established a new high, 5.4 percent above the previous peak recorded in 1963. However, the percentage increase in value of North American mineral production was slightly below overall economic growth. For industry in general, consumer demand held firm throughout the year and overall commodity prices averaged 2 percent higher than in 1963. Wages and salary payments also were up. With the single exception of the dock strike in the United States, the year was free of serious labor troubles and unemployment in both Canada and the States was at a low level. Despite the Viet-Nam situation, relatively tranquil international relations contributed to the forward movement of North American business. Total gross national product (GNP) for Canada and United States, in current dollars, was estimated at US$672.2 billion; 6.8 percent above the previous year's figure. Combined national income in 1964 amounted to US$546.9 billion, which was nearly 7.0 percent more than in 1963. In 1964, gains were recorded in each of more than 50 metals, nonmetals, and fuels commodities that comprise the North American output. The greatest category increase was 13 percent in metals, which was in part attributable to the 14 percent rise to a new record in value of iron and steel in United States, a 29 percent higher value of Canadian iron ore and a 57 percent rise in Canadian zinc. Despite a moderate decline in prices of iron ore and iron and steel products, generally favorable markets and rising prices for metallic ores and metals were a stimulant to the metals industry. Nonmetallic materials, with a total value in excess of US$5.25 billion were 7.3 percent higher than in 1963. High levels of highway and building construction and expanding demand for fertilizers and chemicals continued throughout the year. Noteworthy output increases were recorded for lime,

Jan 1, 1966

By Alla D. Mah

Compilation of data on materials of metallurgical interest is one of the important activities of the Berkeley Thermodynamics Laboratory of the Bureau of Mines. Recent renewed interest in metallurgy of vanadium renders the present compilation a timely guide for experimentation to improve present methods or to develop better methods of extractive metallurgy. Thermodynamic data for vanadium and its inorganic compounds have been critically surveyed, selected, and compiled into one convenient reference from which information can be readily obtained for evaluating heat balances, determining trends, and establishing limits of metallurgical processes. By indicating the direction of experimentation, this report enables the saving of time, effort, and expense which would otherwise be necessary for trial and error experimentation. Much of the data has been obtained experimentally at the Berkeley laboratory. Other data were collected through an extensive survey of worldwide literature through April 1965. Estimates were made when no data were avail-able. Data on the vanadium halides was sparse, and the results derived from existing data were at times divergent. Some of the selected values for the halides may need modification as more or better experimental data become available.

Jan 1, 1966

By W. M. Houston

The phosphate formations of the Pliocene epoch were deposited along the coastal shelf of the eastern seaboard. The deposition of the phosphate is thought to be somewhat contiguous along the early shoreline, and the deposit can be more or less traced over an 800 to 930 mile path from the Florida Gulf Coast, near Ft. Myers, to the Pamlico Sound of North Carolina. This is illustrated in Figure 1. Three areas of commercial importance are currently being exploited from this extensive known deposit: 1 - The so-called ?Bone valley? in Central Florida (multiple operations) 2 - Hamilton County in North Florida (Occidental Corporation operation) 3 - Beaufort County in North Carolina (Texas Gulf Sulphur operation)

Jan 1, 1966

By P. O. Ripley

Into this tumultuous twentieth century, every second, two new babies are born. This is 5,412 per hour, and 130,000 per day. Relentlessly, consistently, alarmingly, they add to the more than three billion human beings who already inhabit the earth. Every tick of tier clock brings with it a problem child, the problem of another mouth to feed, another body to clothe, another human being for whom to provide. On the other hand, medical science has achieved a postponement of death, considerably past the period of a few years ago. Thus, life expectancy has been increased and world population has increased accordingly. Darwin (4) writing in 1962, suggests "It is curious how long the world is taking to perceive that we are living in what is a fantastically abnormal period of history, and one which must inevitably end soon, The first warning note of a possible population explosion was given by Malthus in 1799". He suggested that population increases geometrical while production increases only arithmetically and that soon we would not be able to feed the rapidly increasing population.

Jan 1, 1966

By W. V. McKnight

The paper discusses the equipment and methods used to establish some of the characteristics of a braking system. Some typical tests are described and an explanation of the approach used to derive information from the recorder charts is given.

Jan 1, 1966

By E. Allen

Quebec Cartier Mining Company operates approximately two hundred and fifty pieces of equipment in a climate with a temperature that has averaged 27.5°F during the last seven years. The use of special-purpose lubricants, fuels, antifreeze, rubber compounds, and alloy steels have reduced the cold-weather hazards. In some areas, high-cost cold-weather protective heating devices are being eliminated with experience.

Jan 1, 1966

By G. C. Bernard, L. W. Bernard, L. W. Holm, W. L. Jacobs

The effect of loam on the permeability of porous media to water was studied as a {unction of foaming agent concentration, specific permeability, pressure gradient, length of a porous medium and its oil saturation. At a given fluid saturation in a porous medium, the permeability to water was found to be the same whether loam was present or not. Foam decreases the permeability to water by developing a higher trapped gas saturation than that obtained by water flooding without loam present, increasing the concentration of foaming agent increased the trapped gas saturation and thereby decreased the permeability to water. The presence of oil reduced the capability of most foaming agents to decrease the permeability of a porous medium to water. A few surfactants were found to be effective loaming agents even in the presence of oil. These results are similar to those reported in a previous paper on the effect of loam on the permeability of porous media to gas. The effect of loam was found to persist in long porous media at moderately high reservoir temperatures and during the passage of many pore volumes of surfactant-free water. INTRODUCTION This paper describes part of a study on a novel approach in the use of surfactants for oil recovery; the use of foam rather than water to displace oil. Previously it was found that foam can displace oil which normally is not displaced by water.4 The foam is formed by successively injecting a suitable surfactant solution and gas into a porous medium. Foam appears to have at least two uses in the field: (1) it shows promise as a superior oil recovery agent, and (2) it shows promise as a selective permeability reducing agent. Foam may be very useful in water floods, or in other oil recovery processes, where highly permeable streaks or unfavorable mobility ratios are a problem. A previous paper reported the effect of foam on the permeability of porous media to gas.1 In the present study the effect of foam on the permeability of porous media to water is reported. The specific objectives of the study were to determine: (1) the effect of foam on the permeability to water in porous media of various specific permeabilities, (2) the effect of foam on the permeability to water in the presence of oil, (3) the effect of foam and crude oil on the trapped gas saturation, (4) the effect of foam on permeability to water at trapped gas saturation, (5) the effect of pressure gradient on the permeability to water under foaming conditions, (6) the persistence of foam during the passage of surfactant-free water through the porous medium, and (7) the effect of various foaming agents, length of the porous medium and temperature on the permeability reduction caused by foam. EXPERIMENTAL PROCEDURES EQUIPMENT AND MATERIALS The experimental apparatus consisted of consolidated and unco n soli dated porous media, wet test meters and constant delivery pumps. The porous media consisted of consolidated sandstone cores (6 to 36 in. long), and unconsolidated sand packs (3 to 30 ft long). The consolidated cores had permeabilities of 32 and 1,000 md and porosities of about 20 per cent. The sand packs had permeabilities of 3,500 to 211,000 md and porosities of about 40 per cent. (Throughout this report a term such as 100 md sand" is used. This term means that the porous medium had a dry, nitrogen permeability of 100 md.) Fluids used in the experiments were distilled water, 1 per cent NaCl solution, aqueous solutions of foaming agents, nitrogen gas, air and crude oil.

Jan 1, 1966

The Bluebell mine of The Consolidated Mining and Smelting Company of Canada Limited extends under Kootenay lake, in southern British Columbia, and water control underground has always been a major problem. This paper gives a brief history of the operation, and then de-scribes the methods used by Cominco to keep the combination of lake seepage, ground water and thermal spring water under control. The pumping arrangements are de-scribed in considerable detail, with illustrations to show the various stages of development, and the power supply sys-tem is outlined.

Jan 1, 1966

By Alton B. Cook

A material balance equation was derived for calculating (1) the initial oil volume and (2) the relationship of average reservoir pressure to net gas in storage in reservoirs used for natural gas storage operations. The equation is also applicable to secondary-recovery operations where reservoirs are completely repressured and gas cycled. Using this equation minimized two probable sources of appreciable error in conventional material balance calculations: inaccurate measuring of and accounting for produced gas, and differences between true reservoir pressure and average reservoir pressures as derived from bottom-hole pressure measurements. A new procedure is presented for calculating water encroachment. By solving the conventional material balance equation and the derived equation for gas storage simultaneously, the values for initial oil in place and net water encroachment can both be determined.

Jan 1, 1966

By A. J. Conelius, D. P. Sobocinski

This paper presents a correlation for predicting the behavior of a water cone as it builds from the static water-oil contact to breakthrough conditions. The correlation is partly empirical and involves dimensionless groups of reservoir and fluid properties and of production and well characteristics. The groups were deduced from the scaling criteria for the immiscible displacement of oil by water. The correlation is based on a limited amount of experimenfal data from a laboratory sand-packed model and on results from a computer program for a two-dimensional, incompressible system. Because the correlating groups are dimensionless, they can be used to estimate the performance of water coning cases not specifically considered in the correlation. However, despite its dimensionless nature, the correlation is not completely general and will not provide meaningful estimates of cone behavior in many situations. INTRODUCTION AND BACKGROUND The production of water from oil wells is a common occurrence which increases the cost of producing operations and may reduce the efficiency of the depletion mechanism and the recovery of reserves. We will deal with one cause of this water production, namely, coning. The coning of water into a producing well is caused by pressure gradients established around the wellbore by the production of fluids from the well. These pressure gradients can raise the water-oil contact near the well where gradients are most severe. Gravity forces that arise from fluid density differences counterbalance the flowing pressure gradients and tend to keep the water out of the oil zone. Therefore, at any given time, there is a balance between gravitational and viscous forces at points on and away from the completion interval. When the dynamic forces at the wellbore exceed gravitational forces, a cone of water will ultimately break into the well to produce water along with the oil. We can expand on this basic visualization of coning by introducing the concepts of stable cone, unstable cone and critical production rate. For instance, if a well is produced at a constant rate and the pressure gradients in the drainage system have become constant, a steady-state condition is reached. If, at this condition, the dynamic forces at the well are less than the gravity forces, then the water or gas cone that has formed will not extend to the well. Moreover, the cone will neither advance nor recede, thus establishing what is known as a stable cone. Conversely, if the pressure in the system is in an unsteady-state condition, then an unstable cone will continue to advance until steady-state conditions prevail. If the flowing pressure drop at the well is suffcient to overcome the gravity forces, the unstable cone will grow and ultimately break into the well. It is important to note that in a realistic sense, stable cones may only be "pseudostable" because the drainage system and pressure distribution generally change. For example, with reservoir depletion, the water-oil contact may advance toward the completion interval, thereby increasing chances for coning. As another example, reduced productivity due to well damage requires a corresponding increase in the flowing pressure drop LO maintain a given production rate. This increase in pressure drop may force an otherwise stable cone into a well. The critical production rate, well known in the literature, is the rate above which the flowing pressure gradient at the well causes water (or gas) to cone into the well. It is, therefore, the maximum rate of oil production without concurrent production of the displacing phase by coning. At the critical rate, a built-up cone is stable but is at a position of incipient breakthrough. Numerous papers have been published on critical rates. Some of the better known of these include the work of (1) Muskat and Wyckoff,' who first dealt with the coning problem; (2) Chaney, et al,' who developed expressions similar to those of Muskat but who presented results in a conven ient-to-use graphical form (the "Sun" method); and (3) Meyer and Garder,b hose analysis is based on radial-flow formulas. One assumption in critical production rate analyses is that the cone has built-up to just before its breakthrough into the well. But, these analyses reveal nothing directly about the time it takes for the cone to build up to this incipient breakthrough position. Thus, water-free oil can be produced from a well for prolonged periods at rates above the critical rate before the well reaches the condition to which the critical rate applies. The published literature contains little on the rate of growth of a cone. Experimentally, Meyer and Searcy studied the rate of rise of a cone in a Hele-Shaw model.' Additional related work on water breakthrough and produced water-oil ratios in water driven reservoirs was reported by Muskat," Hutchinson and Kemp," Henley, et al,' and Stevens, et a1.B Theoretically, the basic coning equations for a water-oil system can be developed by applying the conservation of mass to each of the phases, relating flow velocities with pressure by Darcy's law, and relating pressures across water-oil interfaces by capillary pressure. With the usual boundaries at the well and reservoir limits, the solution of the resulting equations for the time behavior of a water-oil interface constitutes a free-surface, boundary-value problem. The shape of the boundary depends on the internal potential distribution, while this

Jan 1, 1966

By J. W. Stevenson

The Bureau of Mines investigated the influence that atmospheric pressure changes exert in a gassy coal mil on a ventilating air current with a system of bleeder entries. During the season when abnormal barometric fluctuations usually occur, recording instruments monitored the air current ventilating an active coal-producing area. It HL he rate of coal production caused a more significant change in methane concentration than did barometric change. The hazard that accompanies methane release due to expansion of the gob gases during atmospheric lows was minimized by the effective bleeder system.

Jan 1, 1966

By Donald Towse

The Permanente plant of Kaiser Cement & Gypsum Corporation is located at a unique thick deposit of Calera Limestone (Figure 1) on the southwest side of San Francisco Bay. Limestone is rare in the eugeosynclinal Franciscan assemblage, constituting less than 0.1 percent of the total volume. On the northwest part of the San Francisco peninsula Calera Limestone is present as isolated masses from the type sect ion near Rockaway Beach southeastward for ten miles, where the belt is truncated by the San Andreas fault. The large Permanente deposit is sixteen miles south of the truncated belt, on the northeast side of the San Andreas fault. Scattered small exposures are known for about twenty miles southeasterly from Permanente. (1,2) Most deposits of Calera are thin; the type section is about two hundred feet thick. At Permanente, however, the normal limestone section contains at least four hundred feet of limestone; and, due to folding and extensive faulting, the total vertical thickness of the limestone section is over 1400 feet. The unusual thickness of limestone is due to low angle thrust faulting. This fortuitous structure formed a deposit of limestone that supplies an 8,500,000 barrel cement plant in a major metropolitan market.

Jan 1, 1966

By Ramon B. Santos

The Atlas Concentrator, reputedly the largest in the Far East today, is located on the island of Cebu in the Republic of the Philippines. It started operation on a 4000 TPD capacity in 1955. An expansion program, coupled with significant improvements both in the Crushing Plant and the Mil, made the Atlas Concentrator what it is today, treating about 14,000 tons of ore per day at a comparatively low cost of about $0.50 per ton treated. The Atlas Copper Mine is at present mainly an open pit operation, with ore supplied from two pits (Lutopan and Biga) north of the Concen¬trator. Development of an Underground Mine, situated on the main ore body at Lutopan, which will be a block caving operation, has been underway since 1963, and this underground mining operation is expected to b e in full production by the latter part of 1966.

Jan 1, 1966