Search Documents

By R. J. Grace

Primarily, this report presents the results of direct efficiency tests which were conducted on the 200-hp Coal-Pak, hot water generator, No. 3 unit, at the Otterbein College heating plant in Westerville, Ohio. Also included is a comparison of fuel consumption of the old plant with that of the new plant, a comparison of efficiencies obtained by the indirect method on a 300-hp Coal-Pak, and the cost of gas vs coal to show the savings effected by the latter. Tests were conducted with ten different bituminous coals selected by Mr. S. A. Frye, business manager at Otterbein College. The coals, of ten different suppliers, from four different states and eight different seams, represented competitive products economically available to the heating plant. The tests were conducted by the usual plant personnel which consisted of the plant superintendent and two assistants. No outside supervision of any kind was given during the tests. The tests were made from Dec. 13, 1960, through Mar. 4, 1961. During this period, 300.03 tons of coal were burned in the No. 3 unit. This tonnage represented 25.5 pct of the total coal requirements for the 1960-61 season. Operation during the period was typical for the comfort heat load which the plant supplies. Of the 78.12 operating days, the boiler was on bank or holdfire 14.31 days, or 18.32 pct of the time. The length of individual bank periods varied from 2 hr to three days. Run periods varied from about 2 hr to 7.26 days. DESCRIPTION OF PLANT AND HEATING EQUIPMENT The new Otterbein College heating plant, completed in the summer of 1957, is located in a 50x50 ft boiler room on the lower level of a combination maintenance building and heating plant. The building is situated away from the main college complex on a hillside, which allows for on-grade delivery of coal to the three bunkers. The bunkers are located directly above and connected with the individual stoker hoppers. Fig. 1 shows an in-plant view of the Coal-Pak installations. The No. 3, hot water, unit is at the extreme right. The heating plant consists of three 200-hp Coal-Paks. Unit No. 1 is operated at 4 psi and carries the steam heating load of 14,000 sq ft EDR (steam) installed in two buildings. Provision has been made to convert these buildings to hot water heating at some future date. Since the unit under maximum load conditions operates only at about 50 pct steaming capacity, a heat exchanger was installed to convert steam to hot water. Thus, during light loads in mild weather the unit can be employed more efficiently to supply both steam and hot water and eliminate the need for operating either of the two hot water units. Units No. 2 and No. 3 serve a hot water heating circuit for a large group of 21 buildings of the College. These boilers deliver hot water at temperatures up to 200°F to the various buildings through distribution lines in tunnels. The present calculated maximum heat loss for the College is 15.195 million Btu per hr. The Coal-Paks have individual design capacities of 6.700 million Btu per hr. Table I lists the design date for the Coal-Paks. The No. 3 unit was chosen as the test unit, primarily because of its bunker location at the far end of the delivery ramp. Because of this location any excess coal above bunker capacity could be conveniently stored and isolated from the adjoining bunkers. Each bunker has a capacity of 30 to 35 tons of coal. The No. 2 and No. 3 hot water generators are equipped with automatic controls which maintain the

Jan 1, 1962

By Paul M. Tyler

FOR the same reason that water is not missed until the well runs dry, the roles of many industrial minerals in wartime are often overlooked. In contrast to the growing shortages of many metals, our supplies of most nonmetallic minerals are limited only by our machinery for taking them from the ground and by our processing facilities. With few exceptions, the demand for increased supplies has been met without fanfare or delay. Only Brazilian quartz crystals, certain kinds of mica, and, latterly, industrial diamonds are on the so-called strategic list, although asbestos, beryl, corundum, cryolite, fluorspar, crucible-grade graphite, ilmenite, iodine, kyanite, monazite, nitrates, rutile, and zircon have caused more concern among those responsible for procurement and are included in our preclusive buying programs. Such specialties are needed urgently, but they are far less important in the over-all picture than the more abundant minerals.

Jan 1, 1942

By A. Kaufmann, B. Cullity, G. Bitsianes

T0 determine the bulk of the phase diagram, techniques for melting, thermal analysis, heat treatment, metallography, and X-ray diffraction that have already been described were used.' It proved difficult to get definitive results for most of the alloy system because of the large number of compounds, their high melting points, and their extreme brittle-ness which made metallography difficult. The final phase diagram, essentially as shown in Fig. 1, was issued with considerable trepidation.' The phase relationships at the two ends of the system were defined with satisfactory accuracy. In the central region between U,Si, and USi, there was great uncertainty concerning the melting points and even the composition of the compounds. At the uranium end of the system, it is quite clear that a eutectic exists at about 985 °C and approximately 8 or 9 atomic pct Si. The a-to-8 transformation is not appreciably altered by silicon, but the 8-to-y transformation is raised to about 795°C. There is appreciable solid solubility in y-uranium, as demonstrated by the micrographs of Fig. 2. The occurrence of the E phase was not suspected at first, since the alloys as melted and furnace cooled gave no X-ray diffraction or thermal arrest indication of it. However, suitable metallography revealed a rim around each of the compound particles as shown in Fig. 3. Heat treatment above 600°C revealed that the rim was another phase which formed by peritectoid reaction between uranium and U,Si,. This reaction proceeds slowly and it is difficult to get it to go to completion. Consequently, there is some uncertainty concerning the exact composition of P and the exact peritectoid temperature. On the basis of various metallurgical studies, it was decided that the most probable composition for t was about 23 atomic pct Si. Metallographic examination shows the closest approach to a single phase at this composition. Likewise, density and hardness measurements of heat-treated alloys shown in Figs. 9 and 10 show a change in slope at 23 pct Si. This is revealed most clearly by plotting the difference in hardness or density between chill-cast and heat- treated alloys as shown in Fig. 4. Zachariasen2 was able to index the diffraction lines of P and to determine the arrangement of the atoms in the unit cell. He concluded that the composition must be US. However, it is felt that the metallurgical studies are reliable and that Zachariasen's X-ray work does not furnish positive proof that the P phase exists exactly at the stoichiometric composition U3Si. There are many instances in alloy systems where a phase does not occur at the composition dictated by the molecular structure. It is possible that the chemical analyses used in the present work were subject to some systematic error. This seems unlikely, however, since recent work in several laboratories seems to show excess compound at 25 atomic pct Si.

Jan 1, 1958

By H. C. Schultz

CERTAIN local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement, breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to usefully develop its full disruptive effect in hard ground. The individual blasts at Chuquicamata are large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with L. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast.

Jan 1, 1928

By H. C. Schultz

CERTAIN local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to usefully develop its full disruptive effect in hard ground. The individual blasts at Chuquicamata are large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with L. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast.

Jan 1, 1928

COLUMBIA SECTION Holds four sessions during year. Annual meeting in September or October. S. S. FOWLER, Chairman, J. C. HAAS, Vice-Chairman, LYNDON K. ARMSTRONG, Secretary-Treasurer, 720 Peyton Bldg., Spokane, Wash. W. H. LINNEY, J. F. MCCARTHY. A special meeting of the officers of the Columbia Section was held in Spokane, Wash., Jan. 10, 1918, for the purpose of organizing and nominating members to the principal committees of the Section. Present: J. C. Haas, Vice-chairman; W. H. Linney, Past Chairman; and L. K. Armstrong, Secretary. J. F. McCarthy, Wallace, Idaho, was appointed fifth member of the Executive Committee. The following were appointed to the Membership Committee: R. M. Betts; for Oregon; W. J. Hall, for Idaho; J. M. Porter, for Washington. A member for British Columbia will be appointed later. The following were appointed to the Committee on Papers: Prof. F. A. Thomson, Moscow, Idaho; Prof. L. 0. Howard, Pullman, Wash.; H. S. Lee, Rye Valley, Ore. A fourth member, representing British Columbia, is to be appointed later. The following members were appointed representatives on the Executive Committee of the Spokane Engineering and Technical Association: J. C. Haas, W. H. Linney, F. A. Ross, L. K. Armstrong. The Treasurer reported a deficit, resulting from the participation of the Section at the Northwest Mining Convention in 1916. It was recommended that the Institute be petitioned to make good this deficit, in addition to the usual annual allowance. The members of the committee who were present expressed their desire to be of greater service in the present war, and discussed at some length the possible means of carrying out their desires. It was later decided to reopen the subject at a subsequent meeting of the Section, or to present it to the Executive Committee of the Spokane Engineering and Technical Association for discussion and cooperative action. L. K. ARMSTRONG, Secretary.

Jan 3, 1918

By Edward W. Parker

(Toronto Meeting, July, 1907.) NOTE.-The material from which this paper has been prepared was collected for the U. S. Geological Survey Bulletin, Contributions to Economic Geology, 1906, and appears also, though in somewhat more extended form without illustrations, in that publication. ALTHOUGH the briquetting of coals and lignites has been carried on for many years in Europe, and has reached a particularly high state of development in France, Belgium, and Germany, it has made comparatively little progress in the United States. The causes for the backwardness of the United States in this regard are several, and first among them has been the abundant supply of cheap raw fuel with which the manufactured article has to compete. With our millions of acres of coal-productive territory, from which the product can in most cases be cheaply extracted, it has appeared in many districts more economical to waste the slack or culm, which con¬stitutes a considerable percentage -of the product, than to attempt to save it at the additional expense required for briquetting. It is for this reason that the view in all sections of the anthracite-region of Pennsylvania is marred by the unsightly culm-banks which encumber the ground, and that in some of the bituminous-districts one sees huge piles of unmarketable- slack allowed to burn up in order to get rid of them. When the coal is of a coking quality, or when the slack can be used for steaming-purposes, these losses are not sustained, but many thousands of tons of what might be converted into usable fuel have been wasted every year simply because of the increased expense involved in its preparation.

Sep 1, 1907

By C. Y. Garber

INTEREST in the sink-float plant operated by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, has recently been largely confined to the preparation and reconditioning of the galena medium. The ease and simplicity of these operations in a concentrating mill producing a flotation lead concentrate has occasioned enough comment to possibly justify a brief description. The subject is treated from an operator's viewpoint only; no effort is made to discuss it in a theoretical or technical manner. PLANT AT BUNKER HILL The sink-float plant was first operated in December 1941. It was built for the purpose of quickly increasing mill capacity with a minimum of equipment. It is the Huntington-Heberlein sink and float process using galena medium and is operated under license from the Sink and Float Corporation, New York city. Lead-zinc ore from the Bunker Hill mine is crushed to pass a I ¼ in. screen and is then washed and separated on vibrating screens having 4 ½ -mm. round-hole punched plates. The screen undersize, amounting to 33 per cent of the mill feed, is dewatered and sent to the ball-mill feed bins. The screen oversize goes to the sink-float plant, where 50 per cent of the oversize, or 33 per cent of the mill feed, is float, which is washed free of medium and disposed of as a tailing. The remaining 33 per cent is sink, which, after washing, is crushed to pass ½ in. and joins the undersize in the ball-mill feed bins. The normal plant capacity is 1700 tons per 24 hr. About 1.7 per cent of the total lead and 3.3 per cent of the total zinc in the feed is lost with the sink-float tailings (Table I). [ ] More complete descriptions of the H. H. process and Bunker Hill sink-float plant are given in several recent articles, listed at the end of the paper. PREPARATION OF MEDIUM AT BUNKER HILL New medium is made intermittently as needed, usually 12 hr. in each 6 days. A small portion of the current mill flotation concentrate is diverted from the lead cleaner cells to a I-in. vertical sand pump and pumped to a two-cell 36-in. Agitair flotation machine, where NaCn and ZnSO4 are added and the grade of concentrate is improved as shown in Table 2. Tailing from this operation is returned by gravity

Jan 1, 1946

By Gill Montgomery

At this moment in the history of the world, the all- pervading and universally most important fact is that the world population is beginning to outgrow its food supply, and the United States has suddenly lost its ability to give away huge food surplus to any nation in the world with a food shortage problem. This, of course, means that, all of a sudden, our government must completely reverse its former bureaucratic stance regarding crop controls and agricultural price supports, to out-right incentives to increase farm production and bring more idle land into food-growing use.

Jan 2, 1967

By M. L. Leonardi

THE Searles Lake orebody is located in the north- west corner of San Bernardlno County. It is a dry lake bed with an exposed salt surface covering an area of 12 square miles. Recoverable mineral values are contained in the mother liquor below the surface of the lake. Stratification in the lake bed has separated the brine into two bodies which dlffer in composition. Although liquor is processed from both bodies, this paper will discuss only the upper structure brine. Fig. 1 illustrates a typical cross-section of the two commercial orebodies. The orebody is composed of a porous salt deposit 70 to 90 ft deep. The upper structure is separated from the lower orebody by a 12 to 16-ft thick impervious mud seam, as shown in Fig. 1. These salt structures are composed of 55 pct solid-phase salts and 45 pct voids which are filled with the original mother liquor. The brine wells are drilled to the separating mud seam and cased to wlthin 10 ft of the bottom. This is done to draw the brine horizontally from the bottom of the structure. It is pumped with multistage centrifugal pumps Into the plant at the rate of 3 milllon gal per day. The first process that was successful was developed by Charles P. Grimwood for the recovery of potash. The first evaporator unit was built in 1916. In the early twenties, Dr. Morse worked out a process for the recovery of borax. This made the cycle more efficient, as the end liquor could be sent back to the evaporators rather than being sewered. In 1926 the American Potash & Chemical Corp. was formed as a new company, and the entire plant was remodeled. The plant at that time produced only potash, borax, and boric acid. Since then the American Potash & Chemical Corp. has added processes for the production of USP boric acid, refined potash, sulphate of potash, soda ash, salt cake, lithium concentrates, Pyrobor (Na2B4O7) bromine, phosphoric acid, and lithium carbonate. The main plant cycle may be depicted as a closed cycle, see Fig. 2. The raw material, brine, enters the cycle to be mixed with the end liquor, known as ML2, from the pentahydrate borax crystallizers. The mixture of these two forms evaporator feed. Evaporator feed is pumped to the evaporators where it is concentrated, with respect to potash and borax. In the same operation water vapor, sodium chloride, salt trap salt, and clarifier salt are removed from the cycle, see Fig. 3 for potash plant product. The evaporators produce a concentrated liquor which contains approximately 19.5 pct KCI. This liquor is diluted as it enters the potash plant to keep all salts, except potash (KCI, 97.0 pct) in solution. Here the moist potash leaves the cycle at 100°F. The end liquor, known as ML1, is pumped to the borax pentahydrate crystallizers, where crude borax pentahydrate is crystallized and removed as solid phase. The ML2 is sent back to pan feed to be reconcen-trated, see page 207. Note that the only water to leave the cycle is in the form of vapor and moisture in the solid phase products crystallized. Thus there is a constantly cycling volume of liquor to which brine is added. Since the volume of liquor cycled does not increase, the brine is, in effect, evaporated to dryness. This would be true if there were no liquor losses. But, as in all processes, there are always unavoidable and accidental losses which reduce the volume of cycling liquors. The losses must be made up with brine. The concentration process is the beginning and the end of the cycling liquors. In this process there are three evaporator units of the triple effect counter-current type, that is, there are three pans in each unit and the heat flows in one direction while the liquor flows the other way through the evaporator pans, see Fig. 4. During the evaporation process a great deal of sodium chloride, burkeite, some sodium carbonate monohydrate, and a little lithium-sodium phosphate are crystallized. The volume of these salts is so great that they must be removed as they are formed or the process would come to a standstill. Brine and recycled mother liquor No. 2 enter the third effect evaporator pan from the evaporator feed storage tanks, see Fig. 5. A steady flow of liquor is removed from the bottom of the No. 3 pan and is pumped through the No. 3 cone of the salt trap, a clear liquor being returned to the NO. 3 pan. A portion of this clear liquor is pumped to the second effect pan. This process is repeated in each pan. The liquor from the No. 2 pan is pumped through the No. 2 salt trap cone and returned to the No. 2 pan.

Jan 1, 1955

By E. J. Roberts

Prior to 1916, thickening was an art, and any accurate decision as to what size of machine to install to handle a given tonnage of a specific ore must have been one of those intuitive conclusions, based on both intimate and extensive acquaintance with thickners and ore pulps. Then in 1916 "knowledge of acquaintance," became "knowledge about" with the publication of the Coe and Clevenger paper.' The unit operation of thickening had graduated to the status of an engineering science. The fundamental similitude relationships for the two major phases of the operation were defined so clearly that batch tests on models as small as liter cylinders could serve to specify protypes as large as 325 ft in diameter.

Jan 1, 1949

By R. Schuhmann

D. W. Fuerstenau (Associate Professor of Metallurgy, Dept. of Mineral Technology, University of California, Berkeley, Calif.) In his excellent paper, Dr. Schuhmann has proposed a mechanism for conlrninution which can be utilized to explain a number of phenomena which have been observed in the size reduction of solids. The difference between the product obtained from a ball mill and from a rod mill can readily be explained by Dr. Schuhmann's hypothesis. Consider that the size distribution of the product from each comminution event is given by y; - 100 (x/ki) (1) where Yi is the cumulative percent finer than size x, ki is the size modulus, and is the distribution modulus for the single comminution event. The total product from a cornminution operation will be the summation of the products from all of the individual cornrninution events. If the size moduli from the various comminution events range from kl to kn , the size distribution of the total product will be a straight line on a log-log plot only to a particle size equal to k ,. Considering 100 volurnes of feed, the value of y for x equal to kl is Riven by where y is the cumulative percent finer than size kj, z is the number of comminution events of kind i, and vi is the volume of each particle crushed. y=z1 qv1+z2 qv2 (k1/k2) +.............zn qvn (k1/kn) (3) F or particle sizes greater than k1 7 e. 6. x = k3, the value of y will be given by k3 A y = z1 qv1 + z2bv2 + Z3uV3 + zn zn qvn (k3/kn)(4) Only when x is equal to k, will y equal 100. 'Thus, the total product from a comminution operation will be a straight line on a log-log plot strictly up to a particle size equal to kl and above that size the line will curve so that y will equal 100 for the coarsest particle or k, (see Fig. 1). The actual shape of the size of distribution curve will depend upon the relative number of conmninution events of different kinds. In the case of ball milling, the ratio kn/kl may be pite large and there will be considerable deviation at the coarse sizes in a Schuhmann plot. kIowever, the grinding action in a rod mill is such that fine particles are protected from the rods by the coarse particles. Consequently, kn/kl will be quite small and the product from a rod mill will give a straight line Schuhmann plot almost to y equal 100%. In his paper, Dr. Schuhmann also has presented a very straightforward definition of grindability derived from the basic energy equation E = Ak-a (5) where E is the energy required to comminute a material to a size modulus of k and A is a constant. According to Dr. Schuhmann, the grindability of a material is the volume of material comminuted finer than unit size per unit of energy expended, this being 1/A. For comparison of grindabilities at any size two numbers are required, both = and 1/A, and anyone tabulating grindabilities should give both of these numbers. Concerning the experimental determination of grindabilities, if the material being comminuted possesses distinct cleavage, the energy re quired for comminution is given by E = Ak-(a-y) (6) where y is small number less than = . Because of cleavage, less energy will be required for comminution. To be certain that cleavage does not affect the gindability of the material being tested, it is suggested that the method used by Dr. Charles for determining grindability be used to ascertain if the deviation exponent y is zero or finite. R. Schuhmann, Jr. (Author's Reply) Dr. Fuerstenau's interesting comparison of rod milling and ball milling

Jan 1, 1961

By M. H. Caron

BASIC U. S. Patent 1,487,145 on ammonia leaching of nickel ores was issued to the author on March 18, 1924. Equivalent patents in other countries were obtained later. The Dutch Syndicate Brikcarbo became interested in the process in 1935; and a couple of years later the late Dr. H. Foster Bain sent samples of Surigao laterite iron ore to Delft and witnessed tests made there on this material for the Philippines Commonwealth. As a result, the author was asked in April 1940 by Dr. Bain to go to the Philippines to erect and take charge of a pilot plant for the process. The World War prevented carrying out this proposal. The Dorr Co. also became interested in the process at about the same period. The investigations by the Freeport Sulphur Co. on the process as applied to the Cuban nickeliferous laterites, which resulted in the Nicaro enterprise, and the results of this operation have been well described elsewhere.1,²,³,4,5 This Nicaro plant was, in operation for almost two years, and during this period produced about 10 pct of the world nickel production from laterites containing 1.35 pct nickel. This plant and its operation were war measures and, in view of this, activities were suspended in April 1947. The results obtained fully demonstrated the technical feasibility of the process and its economical aspects on a commercial scale. In this respect, it should be understood that it is probable that improvements may be made by further development, and that there are possibilities for advantageous application of the process to garnierite and similar ores with higher values in nickel than the laterite iron ores at Nicaro. While the articles cited above have given a certain amount of information, no general article containing all the important process data has been pub- lished. Since the process is of more than local interest, a fuller knowledge of the fundamental and practical factors of the method may be welcome to those interested in this new field of metals technology. The author, accordingly, takes pleasure in submitting this article to the AIME as it represents in a condensed form the results of many years of research. The brief outlines of the fundamental and other factors and the explanation of observed phenomena are presented with as little discussion of details as possible, consistent with clarity. It is a special satisfaction to the author to make some contribution of his own in return for the benefits of the many valuable publications issued by the Institute during his thirty years of membership. Ores Adapted for Ammonia Leaching: All nickel and cobalt ores which originate from weathering of peridotites or similar basic rocks having sufficient values are suitable for treatment by the ammonia leaching process after a preliminary reduction under proper conditions. The formation of these deposits was probably as follows: In the course of time the basic rocks were attacked by atmospheric agencies; MgO and SiO2 were gradually leached out, and secondary nickel minerals formed, such as garnierite, a hydrated silicate of nickel and magnesia. These secondary products are, however, not stable. They decompose in a further stage of weathering and ultimately only a relatively small residue of insoluble oxides remains, known as laterite iron ore with a small nickel content and very little cobalt. Under these mantles of laterite, richer nickel values may be found, usually indicated by the occurrence of garnierite. The more the ore is disintegrated by nature, the higher the iron content and the better the nickel extractions that may be expected therefrom. Table I shows extractions that may be expected from different types of ores, assuming treatment of -200 mesh products and that all precautions have been taken for obtaining maximum extractions. As for the distribution of the various nickel minerals and compounds that may be present, great variations may occur from locality to locality as well as vertically in a deposit. From such "run of

Jan 1, 1951

By N. R. MacMillan

INTRODUCTION The Bullmoose Coal Project is part of a major development in northeastern British Columbia which comprises a new rail line, a new townsite, powerline, highway, the upgrading of the Canadian National Railway's main line, a new coal port at Prince Rupert and two new coal mines, the Bullmoose mine and the Quintette mine. The total investment by all parties is estimated to be in excess of $2.6 billion and made up approximately as follows : [Table No. 1 $ Millions - Quintette Coal Limited 950 Teck-Bullmoose Coal Inc. 275 Canadian National Railway Company 800 6 British Columbia Railway Company Port at Prince Rupert 280 Townsite, Roads 6- Power ] The new infrastructure is intended to serve not only the Bullmoose and Quintette coal projects but also eventually a number of other coal properties in northeastern British Columbia. The Bullmoose project is structured on a joint venture basis as follows : [Table No. 2 Teck Corporation 51% Lornex Mining Corporation Ltd. 39% Nissho Iwai Coal Development 1 0% (Canada) Ltd. -- 100% ] The mine has a capacity of 2.3 million tonnes of clean coal per year. In the initial years 1.7 million tonnes will be metallurgical coal and 0.6 million tonnes thermal coal. After the first three years of operations the annual production of metallurgical coal will increase to an average of approximately 2.1 million tonnes and the production of thermal coal will decrease to an average of approximately 0.2 million tonnes. At this level of 2.3 million tonnes annual production, the Bullmoose mine has sufficient reserves for at least 26 years of production. History Brameda Resources Ltd. commenced coal exploration in the Bullmoose-Sukunka area in 1969. Teck obtained an option on the Bullmoose coal licences in 1970 and started surface exploration and diamond drilling in 1971. Teck earned a 50% interest in the property, and thereafter expenses were jointly financed by Teck and Brameda. In 1981 Brameda merged with Teck making Teck the sole owner. The initial phase of the exploration program, which was completed in 1975, included 7,200 meters of diamond drilling in 35 holes. During 1976 and 1977, detailed exploration and test work were carried out on the South Fork and West Fork areas where multiple seams close to surfaces indicated the potential for large tonnages of strippable coal. In those two years, work included road construction, detailed mapping and trenching to outline the coal seam traces at the surface, 6,300 meters of diamond drilling in 80 holes, and 300 meters of underground bulk sampling from seven adits. Washability tests and analysis work were carried out on the drill cores and adit samples, and pilot plant washability studies were undertaken. In 1978 and 1979 Teck engineers prepared open pit mining plans and production schedules and Kaiser Engineering was retained to prepare a layout of the plant preparation facility. A feasibility study prepared by Teck's engineering group in January 1982 was the base document used by the Lenders in assessing the technical and economic viability of the project. Property Location The property lies some 650 kilometers northeast of Vancouver, and 87 kilometers south by road from the village of Chetwynd. The Sukunka property (British Petroleum) adjoins to the north, the Mount Spieker property (Ranger Oil Option) adjoins to the east, and the Quintette property is located to the southeast.

Jan 1, 1985

By Bruce R. Lipin

Chromite, the only ore of chromium, occurs almost exclusively in mafic-ultramafic rocks and their weathering products. However, not all kinds of mafic-ultramafic rocks are favorable hosts for possible low-grade chromite deposits. For instance, chromium-bearing basalts are not favorable because they commonly contain <0.3% Cr203, and chromite is almost always less than 50 mp in diameter, if it is present at all. Chromite-bearing ultramafic rocks in stratiform and alpine complexes tend to be either ore grade (>25% chromite) or very low grade (<2% chromite); intermediate rocks are scarce. In most complexes, large tonnages exist only in the <2% chromite rocks and the composition of the chromite in those rocks may be unsuitable for metallurgical use. Some nickel laterite districts contain more than lo8 tons of material with 2.0 to 5.5% Cr203, and hence, chromium could be a byproduct of nickel in some laterite districts. In addition, some chromiferous sand placers may contain tens to hundreds of millions of tons of material between 2 and 5% Cr203

Jan 1, 1983

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By J. P. Smith

DURING the winter of 1946 to 1947 potash operations in Germany, France and Spain were visited by the author. The U. S. Department of Commerce, through its Field Intelligence Agency Technical, sponsored the inspection of German properties by representatives of the American Potash Industry. Vast deposits of potash salts occur in the above-mentioned countries, and the production and marketing of these salts are important in their respective economies. Germany An area of some ten thousand square miles of north central Germany is underlain by lenses of potash salts interbedded with greater thicknesses of sodium chloride or common salt. These salt measures are relict deposits from the evaporation of an arm of the Zechstein (Permian) Sea which formerly covered northern Europe. During the peak year of 1940, Germany produced salts containing 1,860,000 tons of K,O and, next to coal, potash is its most important mineral raw material. The German deposits are found in the synclinal areas flanking the Flechtingen, Hartz Mountain and Thuringian uplifts, and, to the north they lie beneath the plains of Hannover. The regional dip of the salt measures is to the north, hence, lenses of potash found at depths of 500 to 1000 m* in the Two general depositional provinces of potash concentrations are recognized: (1) the main basin, and (2) the subsidiary basin. The main basin embraces the producing districts of Stassfurt, Sud Hartz, Halle, and Hannover-Braunschweig. From J. P. SMITH, Member AIME, is Clzief Geologist, U. S. Potash Co., Carlsbad, New Mexico. New York Meeting, February 1948. TP 2621 H. Discussion of this paper (2 copies) may be sent to Transactions AIME before Feb. 28, 1950. Manuscript received May 26, 1948. 40 to 45 pct of the German production comes from this basin. The Werra-Fulda district, producer of 50 pct or more of the German potash, lies in the subsidiary basin. Salt Stratigraphy: Five commercial potash zones or beds are recognized. The three beds present in the main basin are: The Stassfurt bed that occurs near the top of the older salt, and the Ronnenberg and Riedel beds in the younger salt occurring 200 to 300 m, respectively, above the Stassfurt bed. The Stassfurt bed is found over the entire main basin, while the Ronnenberg and Riedel are restricted to the Hannover area. Two potash beds occur in the Werra basin. These are the Thuringian, or lower bed and the Hessen or upper potash bed that occurs 60 m above. These beds lie 210 and 150 m, respectively, below the position of the Stassfurt bed, and are restricted to the Werra basin. The upper bed is 2.5 to 11.5 m in thickness, and the principal ores are hartsalz with varying thicknesses of carnallite. The lower bed averages 3 m in thickness, and contains hartsalz. The upper bed is presently being mined, and the

Jan 1, 1951

By R. Webeler

In order to study the role of work hardening in the fatigue process, use was made of the great sensitivty of the resistivity of AuCu to cold work. A change of the resistivity of AuCu of the order of 1 to 2 pct at the temperature of liquid nitrogen was found to occur as a consequence of severe fatigue. ACCORDING to Orowan&apos;s theory,&apos; the process of fatigue In metals 1s associated with the production of a number of small regions which have undergone strain hardening. This phenomenon is supposed to occilr even if the stress applied during fatiguing is always smaller than the yield stress. In an attempt to verity the existence of such regions, Welber and Webeler&apos; undertook to detect the stored energy associated with severe fatigue in copper. Previous experiments" had shown that the energy stored in a sample of copper which has been cold worked by torsion is released in the temperature range between 150" and 250°C when the sample is heated from room temperature and that no more energy is released (or absorbed) between 250" and 450°C. In particular the stored energy amounted to 0.41 cal per g for a case in which the mechanical energy expended in twisting the sample was 11.9 cal per g. In the case of fatigued copper, however, no release of stored energy could be detected between 150" and 250°C, so that the experimental error of &0.02 cal per g represents an upper limit for the amount of energy stored in strain hardening., It seemed desirable to attack the problem in a new fashion. For this purpose, it was decided to make use of the fact that, if an alloy capable of undergoing the order-disorder transition is ordered and then cold worked, the resistivity, p, increases very greatly above the value for the ordered state even if the deformation is very small. Some insight into the nature of the fatigue process may be obtained then by measuring the resistivity of an ordered sample before and after subjecting it to fatigue. For reasons which will become apparent from the following remarks, considerably more can be learned by carrying out the resistivity measurements at two different temperatures. In the case of a material containing impurities, vacancies, dislocations, or other imperfections of essentially atomic dimensions, the resistivity, p, according to Matthiessen&apos;s rule, can be represented as a sum of two terms p = p, + p, where p, is the (temperature dependent) resistivity of the pure metal, and p, is the temperature independent contribution of the imperfections. Briefly, the physical basis for this rule is the following: The main contribution of the impurities in question to the resistivity results from the fact that they interrupt the periodicity of the lattice and thus scatter the conduction electrons with a probability which is almost independent of temperature. In order that this be the case, it is necessary that the&apos; extension of the impurities be small enough—roughly less than one electron mean free path—so that their main effect on the resistivity occurs for the foregoing reason. If an alloy like AuCu is partly or completely disordered by quenching from an appropriate temperature, Matthiessen&apos;s rule also applies to a very good approximation* with p, representing in this case the resistivity po of the ordered sample and p, the additional (temperature independent) resistivity due to the disorder. In general, the disorder can be represented in terms of atoms which are displaced from their "proper" positions in the superlattice and which thus qualitatively represent the imperfections in the superlattice responsible for the term p,. Since the misplaced atoms are distributed at random throughout the super-lattice, their contribution to the resistivity still can be considered in terms of the scattering of conduction electrons by lattice defects. The situation is somewhat more complex in the case of an alloy disordered by cold work because the process of disordering here does not involve a random redistribution of the atoms; however, Matthiessen&apos;s rule also holds in this case. Whenever Matthiessen&apos;s rule does apply, the values of the quantity /3 = (p? — /(T, — T,), where p, and p, are the values of the resistivity at two fixed temperatures, T, and T,, respectively, is constant (independent of p,) for a given alloy or metal. In particular, if a sample of AuCu is subjected to ordinary cold work, the value of /3 remains equal to Po, the value for the ordered material. According to Orowan&apos;s theory,&apos; as remarked before, a fatigued sample contains a large number of isolated severely cold-worked regions, which make up only a small proportion of the metal. Thus, if a sample of AuCu initially in the ordered state is fatigued, more or less disordered regions will be produced within the ordered material. If these regions are small enough so that Matthiessen&apos;s rule applies, then it follows from the previous discussion that /3 again will remain equal to Po. If the effect of fatigue is to produce cold-worked regions which are macroscopic—of the order of at least several electron mean free paths—the effective resistivity, p, has to be computed by use of the ordinary laws of large-scale electrodynamics. For the sake of simplicity, it will be assumed here that the cold-worked regions are completely disordered and have a resistivity, p,. For a given proportion A of disordered regions the effective resistivity, p, for the current in a given direction depends on the geometrical configuration of these regions. In any case, the value of p for such

Jan 1, 1956

By W. T. Cardwell, R. L. Parsons

This paper discusses the practical problem of estimating a single equivalent permeability for an oil reservoir, or a portion thereof, whose actual permeability varies in an irregular manner. Limiting averages for general types of permeability variation are developed, and illustrated by examples involving important, specific types of variation. Introduction The theory of the flow of fluids through porous media1"4 is becoming increasingly important in predictions of oil-reservoir behavior. In practical applications, however, reservoirs are seldom found to which simple theory strictly applies. Actual reservoirs have complicated shapes and nonuniform permeabilities and porosities. This paper discusses the problem of estimating a single equivalent permeability for an oil reservoir, or a segment of an oil reservoir, whose actual permeability varies in an irregular manner. The equivalent permeability of a reservoir segment is defined as the permeability of a homogeneous segment of the same dimensions that would pass the same flux under the same pressure drop- It is the permeability value that can be used in simple theoretical formulas to calculate the reservoir behavior. To the authors&apos; knowledge, previous theoretical calculationst on systems of nonuniform permeability have been carried out only by Muskat&apos;"; and he has not dealt with irregular variations, except in writing down the general differential equation for the pressure in variably permeable systems.lb In practical work, many calculations necessarily have been made to estimate equivalent permeabilities from the permeabiiity profiles obtained by core analyses. Regarding such calculations, Johnston and Sherborne6 say: Simple arithmetic and weighted averages have been tried on many wells and it has been found that, where frequent sampling has occurred, the arithmetic average is as satis- factory as a weighted average. It is possible that the application of statistical methods to the analysis of permeability data as recently presented by Law8 may prove fruitful. L,, has made a valuable contribution in showing how statistical analyses may aid in picturing the characteristics of a reservoir from those of a necessarily limited number of core samples. It is believed however that the particular problem of the estimation of equivalent permeabilities can be most directly approached from a fluid dynamical viewpoint as given in the present paper. An example is presented of the use of the conclusions herein in conjunction with Law&apos;s method. Theory In order to approach the problem of heterogeneity simply, it is interesting to consider a square block composed of four smaller, homogeneous, square blocks of porous medium, two of which have a

Jan 1, 1945

[Estimated Receipts Dues: Arrears $ 3,500.00 Current 108,115.00 New Members 11,937.00 In Advance 1,763.00 $125,315.00 Initiation Fees 7,250.00 Initiation Fees-Additional if increased to $20.00 7,250.00 Sale of Transactions....3,000.00 Sale of Binding 7,092.00 Sale of Magazine 2,913.00 Sale of Pamphlets 70.00 Sale of Indexes and Emmons Vols 313.00 Sale of Pyrometry 900.00 Sale of Raymond Vol 100.00 Interest received on Bank Balance 500.00 Interest received on Life Memberships 500.00 Advertising-Gross 27,000.00 Voluntary Subscriptions-Estimated 16,000.00 Income from James Douglas Fund 5,000.00 Total $203,503.00] [ ]

Jan 1, 1925