Search Documents

By Nicol SK, Engel MD

Ion flotation involves the adsorption of ionic species, in association with surfactant molecules, at the surface of rising gas bubbles, for the purpose of recovering and concentrating those ions. The objective of this study was to optimise the ion flotation process using a heap-leach liquor, containing gold cyanide, and the surfactant cetyl trimethyl ammonium bromide (CTAB). The aim was to minimise the surfactant reagent dose, maximise the throughput of feed liquor in the process, and satisfy the dual constraints of a high gold recovery and a high volume reduction factor. Development of a first order model of the ion flotation process formed the theoretical basis for the test program procedure and the interpretation of the results. Batch tests were used in order to determine the ultimate recovery curve for the heap leach liquor-CTAB surfactant system. The results indicated that a surfactant dose of about 0.083 g/l would be necessary in order to achieve a satisfactory gold recovery. Continuous tests were then performed on a small-scale pilot plant at the Newcastle Laboratories. The optimum result achieved was a gold recovery of 85 per cent, a volume reduction factor of ten, and a feed throughput of 2.3 m3/m2-h. Recent work also indicates that very much higher volume reductions can be achieved using a larger diameter vessel. The improvement may be a consequence of a reduction in wall effects and hence an improvement in foam drainage.

Jan 1, 1993

Flat jack stress determinations in selected colliery roadways have revealed a range of measured stress from 330-p.s.i. tension to 3,750 p.s.i. compression. Photoelastic examination of loaded plastic and actual rock mo.odel mine openings has shown that the primary horizontal stress required to attain these measured stresses would be from one to three times the superincumbent vertical load.Examination of roof movement with a. borehole oxtensumeter and a series of anchors at various horizons to 30 feet in a. vertical roof borehole showed that when a standing face waa.s advanced the roofmovement was practically confined to the lower two feet. The ma.j ority of this movement occurred during the 36 hours after mining at this face commenced.The use of a. radioactive isotope and a. scintillation counter in a. pair of parallel bcreholes promises to be sensitive and accurate method of roof bedding plane crack detection.

Jan 1, 1963

By S F. Simmons, A McOnie, J L. Mauk

Three cross sections, 200 m apart, display the distribution of indicator hydrothermal minerals across the Empire zone of the Golden Cross epithermal Au-Ag deposit, Waihi, New Zealand. These minerals are used to interpret the temperature and composition of hydrothermal fluids. The distribution of interstratified illite-montmorillonite and illite indicate that temperatures ranged from 140 to >220¦C, with temperatures above 220¦C predominating. The mineral assemblage of quartz-adularia-chlorite-illite-calcite-pyrite envelops the Empire vein system and stockwork, and reflects formation from an alkali chloride water whereas the mineral assemblage of replacement calcite-interstratified illite û montmorillonite-kaolinite forms a carapace and reflects formation from a CO2-rich steam-heated water. Alkali chloride waters appear responsible for the epithermal Au-Ag mineralisation.

Jan 1, 1995

The Olympic Dam Project constitutes a major resource of Copper and Uranium and has been under intensive evaluation since the discovery in 1975.A 500 metre deep rectangular shaft has been sunk into the deposit and this has been followed by 8400 metres of level, incline and decline development. 5 surface ventilation raises have also been constructed.Large scale trackless equipment is used to carry out the development, and productivity statistics are given.The paper describes the functionalised system used in the development program and discusses the maintenance support, and services required to carry out these works.The objectives of the Exploration Development program and the satisfactory results obtained from this work are also discussed.

Jan 1, 1985

By Wright D. J

Successful heap leaching depends on three major factors: 1. Chemical conditions appropriate for the dissolution of the valuable metal; 2. Contact between the leach solution and the valuable metal particles; and 3. Movement of the leach solution through, and out of, the heap. Given that appropriate chemical conditions can be provided, and the individual particles have sufficient permeability to allow solute/solvent contact, the problem of getting the solution to and from the particles remains. Non-uniform percolation of solution throughout the heap, caused by the presence of fines, is a common problem which occurs, to some extent, with all heap leachable ore. The conventional solution to this problem is agglomeration, which involves the attachment of fine particles to larger particles, effectively modifying the size distribution by preventing the fine particles from acting on their own. While agglomeration must be considered as an extremely effective technique with virtually no limit to its application from a technical point of view, its application is limited by economic considerations. A new technique has been developed which is not only a low cost alternative to agglomeration, but also has the potential for enabling the application of low cost heap and vat leach techniques to a significantly wider range of ores than current practice would suggest. The new technique, known as Electrokinetic Leaching, utilises electro-osmotic flow to enhance percolation through the heap. This paper describes and presents results of the laboratory testing, pilot heap operation and commercial application of Electrokinetic Leaching of a low grade gold ore and a tailings deposit. Comparative cost analyses between conventional and the alternative processing techniques are presented.

Jan 1, 1994

Laboratory experiments have been used tostudy a wide range of convective processes which are significant for the formation of rocks and the ores that form in them. Metal-rich solutions flowing through the sea floor produce 'black smoker' chimneys; both the size and structure of a solid chimney and the height to which the plume of effluent rises above it can be predicted using model experiments. Analogues of processes in solidifying magmas can also be studied using crystallizing aqueous solutions. The release of lighter or denser residual fluid as crystallization proceeds, and the resulting compositional convection, have a vital influence on the differentiation of initially homogeneous magma and on the evolution of stratified magma chambers. Mixing during the replenishment of magma chambers, and its dependence on the rate of filling and on the fluid properties, have also been studied on the laboratory scale. Experiments carried out in different geometries have been applied here to the formation of platinum and chromite ores and komatiite lavas. Larger-scale mantle convection, in particular the motion of subducting plates and plumes rising from the core-mantle boundary, also determine the tectonic settings in which ore bodies form. These phenomena too can be usefully investigated in laboratory experiments using very viscous fluids.

Jan 1, 1990

By Liu Y

Ventilation, air leakage, and various cutting, loading and support movement operations all have a role in dust distribution on longwall faces as shown by the results of a large number of dust measurements on different longwall operations in the Bulli seam on the South Coast. It is concluded that leakage of air on the face has demonstrable mfluence on the exposure of the shearer operator to dust level. It is possible to calculate dust generated by various elements of a rrurung operation on the face from a single point measurement. In the examination of dust deposition from the source of generation as a function of particle size, it is found that respirable dust can remain airborne over long distances without any significant drop in concentration, if unobstructed.

Jan 1, 1995

By Duran A, Eggers M. J

It is standard practice in geotechnical studies for mine design to drill a series of inclined oriented boreholes into the proposed pit walls. However, this investigation tool is often used without an adequate understanding of the inherent shortcomings in the method and the many potential sources of error. Of the more commonly used orientation methods in Australia the clay imprint technique is probably the most reliable. Contoured stereographic plots of oriented core data are frequently characterised by diverse pole distributions and low concentration maximums compared with line mapping data. Common sources of error producing these poor results are misinterpretation of orientation marks or imprints, inaccurate marking of the reference line, errors in the structural measurement of the defects, lack of continuity information and blind zones sub-parallel to the borehole direction which correction methods frequently do not fix. Line mapping is the preferred method of structural data collection due to the lower overall cost, availability of continuity information and higher accuracy. The projectability of field mapping data to final wall positions can be assessed with a good understanding of the regional geology and local structural patterns. Where field mapping is not possible due to a thick regolith cover, core orientation should be carried out by experienced personnel to minimise the many potential errors.A series of case studies are presented which compare oriented core with mapping and highlight the inherent problems with the technique.

Jan 1, 1992

In 1980 Pancontinental Mining Limited decided that while the Jabiluka uranium project was still a major focus of the company's efforts some diversification was necessary. At this time it was decided to include precious metals in Pancon's exploration and acquisition objectives. As a result the now Paddington Gold tenements were acquired, explored and developed. Today, it rates as the 6th largest gold mine in Australia and at an expanded throughput of 1.2 million tonnes per year of ore it will produce about 110,000 ozs of gold per year. Following extensive exploration activities by Pancon's Exploration Division the Operations Division continued with development drilling finally proving up a reserve of about 8.4 million tonnes at an average grade of 3.2 g/t. An in- house preliminary feasibility study was followed by a two phase feasibility study by Davy McKee. This resulted in a recommendation to the Pancon Board of Directors to develop Paddington with an annual throughput capacity of 875,000 tonnes. This paper describes the acquisition, exploration and development of the Paddington project. It goes on to

Jan 1, 1986

The reduction in the number and duration of machinery and equipment failures is an important source of economical efficiency enhancement in the Polish coal mining industry.Non-dismantling methods have been thus developed to evaluate the technical state of machines. Among these viroacoustical methods are the most effectively employed. Two-directional organisation of the testing can be chosen, such as periodical and continuous inspection. The monitoring methods for ball bearing, rope tension uniformity, longwall shearers, main fans and shafts installations etc. Instrumentation for monitoring measurements are either of intrinsically - safe or explosion - proof construction, which enables using them in a gas-hazard atmosphere. The development of these procedures has led to the trials to insert the diagnostic methods into the organisational scheme of a coal mine.

Jan 1, 1991

Five Hypotheses are given for factors influencing long-run metals price forecasts. 1 . Geologists succeed when given the money. 2. Better understanding of a metals market depresses its price. 3 . Statistical techniques get forecasts wrong. 4. Long-run metals prices are related to crustal abundance. 5 . Economic cycles affect metals prices more than is realised. These are then framed within the transition between eras as influenced by apparent long waves in economic activity. Innovation surges during the transition between eras. The transition to the 5th Wave since the Indus- trial Revolution 200 years ago is now underway. Finally, price projec- tions are given both for the 5th Wave and 200 years from now on the assumption that a similar monetary measure to today will be then extant.

Jan 1, 1988

The Ok Tedi open pit mine will have final wall heights in excess of 750m. The behaviour of these excavated slopes will be influenced by the presence of numerous defects. This paper discusses the identification of possible failure mechanisms within the pit walls based on mapped fault and joint data. Results from analyses using these data have formed the basis for the ultimate pit design.

Jan 1, 1994

By Miller J. D

The mechanism of adsorption of gold from alkaline cyanide solutions by carbon has been the subject of much research over the past decade. In this paper, the nature of the gold cyanide adsorption phenomenon is investigated, particularly with respect to carbon substrates and associated surface adsorp- tion sites.

Jan 1, 1991

Mine pit slopes in the Pacific Rim are a geotechnical challenge because of the complex geology in which they are developed. Mines are currently being fast-tracked to meet the increase in commodity prices, often resulting in some reduction in ground studies and short-cutting of design procedures. In addition, the resources boom means that skilled personnel are in relatively short supply. At a time when mine pits are getting bigger and deeper, and the engineering is getting more demanding, there is an increased demand on managers to effectively implement the work.   Experience both in New Zealand and the Philippines, display the complex range of geological environments in which pits are being excavated. Working in these conditions has shown that successful geotechnical design requires a strong geotechnical model based on sound geology. An appropriate level of investigation and analyses results in a certain level of understanding for the mine design. There is a point where additional expenditure (on investigation and analyses) is not warranted based on the expected minimal impact on decreasing the level of perceived risk on the project. For most projects in our experience the analytical methods and complexity of geotechnical assessment changes increases as the level of knowledge grows.

Jan 1, 2006

By Forsythe DJ, Sun S-S Andrew AS

Paragenetic, fluid inclusion, stable isotope, and 87Sr/86Sr and 143Nd/144Nd isotope studies of the Mt Carbine tungsten deposit in North Queensland provide information on the sources of the mineralising components and record the history of fluid-rock interaction during the hydrothermal process. The ore minerals , wolframite and scheelite , are contained in quartz veins which post-date the major deformations in the Siluro-Devonian Hodgkinson Formation . Mineralisation was immediately preceded by the emplacement of the Mossman Batholith (280 ¦ 7 Ma). Two major stages of mineralisation are present and separated by a brittle fracturing episode . The stable isotope and Sr and Nd isotope data suggest that the ore fluids during stage I and most of stage II mineralisation were a mixture of magmatic water and non-magmatic water (connate or metamorphic) which had experienced a long residence time and had extensively exchanged with the sediments at high temperature. Subsequent mineralisation events were dominated by fluids of meteoric derivation with a short residence time. The data imply that other solutes, such as W, were probably derived in minor part from local country rock sources with the major contribution coming from a magmatic source related to the granite batholith.

Jan 1, 1987

By Aspinall T. O, Loch R. J, Bell L. C

Design of reshaped spoil surfaces is an important pan of rehabilitation of spoil piles resulting from open-cut coal mining. To achieve the optimum design, it is necessary to make accurate predictions of soil losses from spoil piles. Predictions can be based on data gathered using laboratory and field rainfall simulators and field plots. These data are used to derive input parameters for erosion prediction models. Model input parameters include rainfall erosivity, spoil erodibility, sediment size distribution, runoff, soil loss and peak runoff rate. Model outputs can be used in design and include predicted sediment size distribution and predicted soil loss.The traditional method of gathering input data is monitoring field plots. This method is very expensive, must be done on a long-term basis and is affected by irregular rainfall. Long-term field plots are necessary to obtain data that can be applied to empirical prediction models such as the Universal Soil Loss Equation (USLE).

Jan 1, 1992

By Barclay C, Jacobsen M, Towsey C

The Emperor Gold mine at Vatukoula, Fiji, is a nine million ounce gold telluride deposit. In January 1992, the mine was on the verge of closure when the current management team took charge. Losses had been incurred for two consecutive years and the published resource amounted to less than five years of production. Relationships with the workforce, the government and the general public were poor. Today, the mine has recorded three consecutive years of profit, has resources that will support the operation for at least 20 years and has excellent relationships with employees, government and the general public.

Jan 1, 1997

A synthetic gold-silver telluride material (mainly sylvanite) has been prepared and its physical and chemical properties checked. Flotation tests using a Hallimond tube were conducted using commercial xanthate collectors. At collector concentrations of 10-3M with the addition of 5 × 10-4 M CUS04, no obvious differences in the mineral recoveries were seen irrespective of whether amyl, secbutyl, isobutyl or isopropyl xanthates were used. However, when the concentration of xanthate was reduced to 10-4 M or in the absence of the copper sulphate activator, the effectiveness of the collectors was in the order: amyl > secbutyl > isobutyl > isopropyl > ethyl. Changes in the slurry pH appeared to have little effect on the recovery of the telluride mineral.Leaching tests of the precious metal telluride showed that both gold and silver dissolve in alkaline oxygenated cyanide solutions but at a much lower dissolution rate than metallic gold or silver. Both leaching tests and electrochemical measurements indicate that the dissolution rate of gold-silver telluride is controlled by the pH and cyanide concentration of the leachant.Roasting the gold-silver telluride materials in air at temperatures between 550 and 750°C resulted in its decomposition into a metallic gold-silver alloy and tellurium dioxide.

Jan 1, 1994

By Rowley M, Bradford P

Plutonic Resources Limited (formerly known as Pioneer Mineral Exploration Limited) delineated, developed and operates the Plutonic Gold Mine located 180 kms northeast of Meekatharra, Western Australia. Gold mineralisation was discovered in the Marymia greenstone belt by Great Central Mines NL (GCM) in 1988. There was no previous, recorded gold mining activity in the area. In May 1989, Plutonic Resources Limited (PRL) entered into an agreement to acquire a 51 per cent interest in the three Mining Leases containing the Plutonic deposit from GCM. Subsequently in December 1989, PRL acquired the remaining 49 per cent interest in the Mining Leases. PRL and GCM are also involved in a 51:49 regional joint venture on extensive Exploration Licences in the vicinity of the Mining Leases. Following due diligence validation, reserve delineation and testwork, a feasibility study was undertaken in conjunction with JR Engineering Services, which led to the financing and development of the project for operation in August 1990.

Jan 1, 1991

By Toro HCH, Von Borries GH

A brief description of the semi-autogenous grinding (SAG;) facilities of Compania Minera Disputada de Las Condes is given. A data-logging and computer system was connected to the plant inter facing the existing analog control system in a supervisory s, control philosophy. The development of a control straiov,v t,) maintain maximum power of the SAG mill atsubjected to process restrictions is shownThe present control scheme is discussed inalgorithm was designed based on correlations onLween vartaoles. Associated with this, a direct level of control was developed be, on classical control algorithms, process inter-active tuning has been included. Also, an algorithm to prevent overloading of the is discussed. Control scheme tests are presented in comparison t manual operator control under the same conditions. It is shown t the control strategy gives a more stable operation and a higher plant throughput.

Jan 1, 1985