Search Documents

By B. W. Williams

The crack propagation behaviour of Zr-2.5Nb pressure tube material was studied through comparison of the measured behaviour with the predicted response from finite element analysis. Three-dimensional finite element simulations of compact tension specimens were performed using the crack tip opening angle as a fracture criterion to allow for crack propagation. To obtain reasonable agreement with the measured behaviour, it was important to capture both the anisotropic plastic deformation behaviour of the Zr-2.5Nb material through use of the Hill-48 yield criterion and damage due to void growth, nucleation, and coalescence through the use of a Gurson-based constitutive model in the simulations.

Jan 1, 2010

By S. H. Lucas

"This paper describes the development and application of single-stage fluidized bed continuous ion exchange to the following processes: removal of base metals from mine water; cyanide removal from gold mill waste; uranium removal from sulphuric acid leach liquor; and uranium removal from mine water. IntroductionThe recovery of metals by fixed bed ion exchange has been practiced for many years. However, the operation has been semi-continuous and can only treat clarified liquors. Substantial savings could be made if the operation were continuous, thus reducing the resin inventory, and if the costly filtration and clarification steps could be eliminated. Work has been in progress over the past twenty-five years on the recovery of metals from unfiltered ore leach slurries, heap leach liquors and mine drainage waters containing a small amount of suspended solids. In the case of dilute waste solutions, with suspended matter and high flow rates, filtration is usually prohibitively expensive.Continuous ion exchange operation using fluidized beds has made it possible to reduce considerably the resin inventory and to allow the treatment of unclarified liquors and slurries. The subject has been reviewed on several occasions (1. 2. 3, 4). Although fluidized beds in multi-stage columns are an improvement over previous resin-in-pulp treatment, they have complicated internal structure and I or involved automatic control systems to move the resin stages.Slater and Prud'homme performed studies on multi-stage fluid beds, and concluded that the performance of single, deep fluidized beds of resin with continuous or semi-continuous flow of both phases would be worth investigating, particularly in the case of very dilute metal solutionsoi, A pilot plant was designed and built at CANMET in a cooperative project with Dr. Slateroi. The use of deep fluidized beds of resin (with a large height/diameter ratio) for treating dilute solutions has the attraction of engineering simplicity. Extreme simplicity of equipment design is considered of paramount importance when treating, for example, mine waters at high flow rates, possibly of the order of several million gallons per day. This paper describes the development of the concept of single-stage fluidized bed continuous ion exchange arid reviews the pilotplant development of processes for the treatment of base metal mine water, cyanide waste water, uranium leach liquor and uranium mine water."

Jan 1, 1980

By S. Shokri

The increasing size and complexity of mega construction projects result in having several geographically distributed stakeholders, collaborating with each other to successfully deliver the project. Electronic Product and Process Management Systems (EPPMS) are recently emerging to facilitate the collaboration between stakeholders, reduce the surprises and issues, and improve the project productivity. These are commercially successful but evolving systems. An important component of EPPMS is the Interface Management System, which aims at formalizing and automating the communication channels between stakeholders. An interface is generally considered the link between construction elements, phases, or stakeholders. An interface Management System (IMS) involves five iterative steps: (1) Interface Identification, (2) Interface Documentation, (3) Interface Transferring, (4) Interface Communication, and (5) Interface Closing. A fundamental part of step 2 is recognizing different roles in dealing with interfaces. Each stakeholder is assigned a different role, such as responsible, accountable, consulted, and informed. In a mega project, several thousands of interfaces exist with complex relationships between stakeholders. Therefore, identifying stakeholders with higher responsible roles has been requested as useful information to the project owner in dealing with some of the project risks. After the interfaces are determined, and the responsibilities are allocated, the critical stakeholders are identified using the centrality concept in Social Network Analysis. The critical stakeholders can be determined at the highest level, considering all types of interfaces, as well as for each specific type or discipline-related interfaces. The proposed methodology is applied on a hypothetical offshore project with over 500 interfaces. In fact, this project is a simplified representation of a real scale Liquid Natural Gas project. In order to reduce the complexity of calculations and clarity of explanations, the simplified case study is used. By implementing IMS in mega projects, different parties not only formalize the communication between each other, but also gain better visibility concerning their roles and responsibilities. In addition, the owner benefits from analysing the complex relationships between stakeholders to further identify critical ones, along with other criteria like package cost, stakeholders? experiences, etc.

Aug 1, 2013

By M. B. McClenaghan, O. P. Lavin, Ian Nichol

"Exploration in most areas of Canada has to contend with problems posed by glacial overburden. In many areas exploration for gold has been based on the sampling of tills, frequently by deep overburden drilling, and analyses of heavy mineral concentrates. Notwithstanding the significant role that till geochemistry has played in the discovery of some important gold deposits over the last few years, increased appreciation of the nature of the glacial history and stratigraphy and the character of gold within till has led to the recognition of a number of ways whereby the effectiveness of exploration can be improved upon.In order for till geochemistry to be useful in exploration, a number of conditions must be fulfilled, including:1. mineralization, or alteration halo related to mineralization, subcropping at the bedrock/overburden interface;2. glacial erosion and dispersal of a recognizable signature of mineralization into the glacial sediments;3. preservation of glacial sediments containing this geochemical component (trace metal or mineral) at positions subsequently selected for sampling (normally drill sites);4. correct identification of specific till units and associated ice movement history;5. collection of adequately large and representative samples;6. appropriate sample preparation and processing;7. appropriate geochemical analyses; and8. correct data processing and interpretation.While we have no control over the first two geological conditions, and only limited control over till availability, we can control the quality and thoroughness of sampling, sample identification, sample preparation, analysis and interpretation. In particular attention needs to be focussed on obtaining a large enough sample to be adequately representative, an unbiased sample must be collected, together with appropriate sample processing, analysis, data processing and interpretation. It is considered that by modifying or extending existing approaches to gold exploration the chances of exploration success can be increased. In particular, analyses of both the heavy mineral and minus 63 µ m fractions of till is recommended because gold in till may occur in different size fractions."

Jan 1, 1992

Abstract: ?The paper will review the perspective of Scotia Capital on financing mines, mining projects and mining companies in today's world of major increases in commodity prices, increases in capital and operating costs, shifts in foreign exchange rates, and increasing scrutiny of mining's social license ?Focus on debt financing alternatives Key Assumptions: ?Assume financing a mining asset (i.e. not an exploration play) ?Exploration is generally financed with equity ?private placements or public offerings on an idea

May 1, 2006

By D. Royston

In SAG mills fed with a variety of ore types, hard packing between the shell lifters can come and go depending on rock type and rock size distribution and the presence of a binder. Packing can appear in all sizes of SAG mills, and can be tenacious. High ball impact forces (depending on ball size) in larger mills may compact and encourage packing. Packing can have a negative impact on milling performance and a change in shell liner design may be required to remove it. However shell liner design changes need to be managed with care to ensure liner reliability. In smaller mills control of packing can extend shell plate wear-life and may help to maintain milling performance in fixed-speed mills through the liner wear-cycle.

Jan 1, 2012

By E. W. Garner

THE greatest problem confronting business managers in modern times is not production, but distribution. It would be easy to expand productive output, but it is difficult to find markets for all that is produced. The fundamental source of economic difficulty, in the view of many observers, is a lack of proper balance between productive capacity and consumptive capacity. The studies conducted by the Brookings Institution on the general subject, "The Distribution of Income in Relation to Economic Progress", have led to conclusions of far-reaching significance, which may be summarized briefly as follows: (1) We have never lived beyond our economic means or capacity. (2) We have not been suffering from general overproduction. (3) We have not as yet reached a stage in our economic evolution at which it is possible to provide adequate standards of living for everybody. ( 4) It would require less than a 25 per cent increase in purchasing power among the masses to absorb our full productive capacity. (5) Production-curtailment programmes-whatever their merit in meeting temporary maladjustments-can only lead to national impoverishment. (6) Our inability to find markets adequate to absorb the full output of our productive establishments is explained by the unequal distribution of income and consequent restricted flow of purchasing power through consumptive channels. (7) The slow rate of growth of consumptive demand serves to retard the rate at which new capital is constructed, and hence the rate of economic progress. (8) The primary need is a rapidly expanding total income, and a broader diffusion of this income among the masses of the people. (9) A broader diffusion of income can best be achieved by reducing prices as rapidly as increasing efficiency will permit. That is to say, the benefits of technological progress, mass production, and low unit costs must be promptly passed on to consumers in the form of lower prices-giving more for each dollar.

Jan 1, 1936

By Tim Gitzel

Thank you for your introduction, and thank you to the CIM for inviting me to make a presentation to you today. This is my first opportunity to report to you on the status of the Canadian uranium industry and I am pleased to tell you that the industry is in good shape, and well positioned for the future. As you will no doubt be aware, Saskatchewan benefits from the world?s largest known highgrade deposits of uranium as well as from a high level of provincial, public and northern community support. It is within this unique combination of geology and community that our industry operates. Uranium markets have been extremely competitive for a number of years for several reasons. First, deregulation in the nuclear electric power industry has tended to encourage fuel buyers to use up their large inventories built up at a time when rapidly increasing demand was anticipated. Second, alternate sources from surplus commercial stocks, military materials and reprocessed fuel have presented a major additional source of uranium supply. Today, these secondary supplies are meeting about half of uranium reactor feed requirements. Canada (that is, Saskatchewan) is the world?s largest ?natural? uranium producer with about a third of the global production. Saskatchewan?s mines produced more than 30 million pounds of yellowcake in 2002. Despite low prices, steady demand for uranium will continue. In fact, an increase in world uranium production in 2002 helped feed a more than 3 per cent increase in reactor fuel demand. Low cost production is important for surviving low market prices, but investments are based on longer-term strategies rather than simply responding to market cycles. Cost is not the only issue. In these times of increasing regulatory and public scrutiny we must continue to earn the trust of our stakeholders by adopting the highest standards and staying on the leading edge of technical, social and environmental developments. Managing these issues is as important as traditional concerns of ore grade and cost of production. The last two decades of the 20th century saw the Province of Saskatchewan rise to prominence as the leader in uranium production from facilities, which were at the time deemed world class. These facilities are now either at - or nearing - the end of their production years. We are now bringing on new facilities that will position Saskatchewan to remain the world leader in uranium production for many years to come.

May 1, 2003

By Thomas Genty, Pascal Marcotte, Matthew Gillman, John Baechler

Elevated concentrations of ammonia nitrogen is a common characteristic of mine impacted water and generally results from the dissolution of undetonated explosives (i.e., Ammonium Nitrate and Fuel Oil and emulsion explosives) by contact water. Several active water treatment technologies are commercially available to remove ammonia nitrogen, but reduction of active treatment demand by promoting natural attenuation is considered best industry practice. In this paper, the results of laboratory-scale and full-scale trials of a semi-passive approach (i.e., enhanced algae growth) to remove ammonia nitrogen at the Meliadine mine are presented. Phosphorus was found to be the limiting factor to algae growth at the mine site. The addition of various concentrations of phosphorus was first tested at a laboratory scale. The samples were exposed to in-situ conditions, and ammonia nitrogen removal rates ranging from 40% to 93% were achieved over a period of 24 days. This paper also presents the methodology and results of an in-pond treatment during which a 50% ammonia nitrogen removal rate was observed after 68 days. The studied mine site uses breakpoint chlorination as its primary treatment approach for ammonia nitrogen removal. The results presented in this paper show the potential of using enhanced algae growth as a pre-treatment method, subsequently reducing the quantity of chemicals required for operating the breakpoint chlorination plant. This potential requires further investigation and additional trials are currently under evaluation.

Jan 1, 2023

By Peter Moser, Thoma Oberndorfer

"Within the research project “Mine Development” (Fettweis and Moser, 1990) a PC-based mine database has been built up since 1991 and so far includes detailed technical and economic data of about 150 under-ground hardrock mines in industrialized countries worldwide. These data represent about 50% of the underground hardrock mines in west and central Europe, Scandinavia, United States, Canada and Australia (Fig. 1). The mining operations included in the database have been visited directly and analyzed with respect to their deposit conditions, their general design and layout and also their operational and economic performance.The main aim of the Mine Database is to make a contribution to an improved planning of new underground hardrock mines. An analysis of current mine planning practices shows, that both personnel and company experience is still a dominant factor in planning new underground hardrock operations. Through the information included in the Mine Database the experience of a single per-son or company is supplemented by the experience of a wider group of people. The Mine Database makes the huge amount of experience that is available worldwide in the field of under-ground mining accessible for new mining projects. From that a contribution to a more reliable mine planning procedure based on the performance of existing mining operations is expected.In addition to its use in planning new mining operations, the Mine Database can con-tribute to the exchange of technical data among different mining operations, especially on equipment performance, etc. Such an information service is offered by the Department of Mining Engineering & Mineral Economics in Leoben and is already being used by different mining companies. To respect proprietory information, company specific information is not released under any circumstances.The cost of building up the Mine Database, so far, is about US$500.000 — two thirds of which is labour, and one third, travel."

Jan 1, 1996

By S. Klemmer

Potential problems associated with groundwater inflows are a major concern to many Saskatchewan mining operations. Rock mass behaviour and stability have been linked to groundwater inflow potential. An estimate of the hydraulic conductivity of the rock mass is an important factor for assessing groundwater inflow potential. This paper presents a procedure that was developed to conduct air permeability tests, for estimating the hydraulic conductivity of the rock mass. Tests were conducted near underground excavations with the goal of assessing links between measured air permeability, rock mass classification and the rock mass response to adjacent excavations. Measured changes in air permeability corresponding to the distance from excavation boundaries may indicate changes to joint properties such as joint aperture, continuity and frequency. This study outlines the instrumentation, the experimental and analytical procedures, and the preliminary results from testing.

Nov 1, 2011

By S. Kamado

Development of new SF6 alternative cover gas with low global warming potential is strongly desired for melting and casting of magnesium alloys. We have tried to apply several kinds of HFC and HFE gases with low potential from 30 to 950 as protection gases to AZ91D alloy melt in the temperature range of 650 to 800°C. As a result, protective film consisted of MgF2 and MgO is formed on the melt surface and ignition-proof effect is sufficiently obtained at all the temperature ranges even when flow rates of mixed gases containing CO2 as a carrier gas are almost the same as those using SF6 gas. Reduction of global warming potential exceeds 98% at 650°C and 89% at 800°C in comparison with a mixed gas of CO2 and SF6.

Jan 1, 2006

By G. Avramovic-Cingara, H. J. McQueen

The microstructure of commercially pure aluminum was investigated by using polarized optical microscopy (POM), orientation imaging microscopy (OIM), and transmission electron microscopy (TEM) techniques. Specimens were deformed in torsion at 400°C and equivalent strain rate of 0.1 s-1, to various strains of 0.2, 0.5, 1, 4, and 6. The results indicate that POM can usefully reveal grain and subgrain structures over a large field in aluminum. TEM is most suitable to study dislocation substructure and evolution of subgrains. While TEM microscopy and OIM are capable of resolving individual subgrains, OIM can not reliably distinguish subgrains with small misorientations, particularly in samples with low strain. On the other hand, the OIM technique is very useful in the analysis of many regions surrounded by high, medium, and low angle boundaries (HAB, MAB, LAB). Various misorientation maps were studied using different data processing methods. The analysis revealed that the subgrain size is relatively insensitive to strain. The fraction of low LAB ( < 5°) decreased and HAB (>15°) increased conversely with increasing strain, whereas MAB (5-15°) remained stable. The development of an increasingly bimodal grain boundary misorientation distribution is consistent with the predominance of dynamic recovery (DRV) in the evolution of microstructure, combined with geometrical dynamic recrystallization (gDRX), now called grain-refining DRV.

Jan 1, 2006

By D. Groenveld, M. Rozou

"Recent trends move towards automation, smart sensors, internet of things, powerful DCS, and more data. Are those trends already utilized in a real time production environment? Today operators still have to monitor several complex processes at the same time and predict their behavior based on an overwhelming amount of data available.The fact of the operator being overloaded and humans being unable to process multivariable problems shows the need of a tool merging essential data and providing consistent, sound decisions for long-term profitability.This paper shows a successful execution of ABB’s process improvement services in Aitik (Boliden SA), a copper mine located in Sweden. Soft sensors, fuzzy rule blocks and model predictive control were seamlessly integrated in the control system of the grinding area, resulting in proper control of mill loads and particle size without violation of any constraints.INTRODUCTIONDepending on the ore characteristics and the targeted plant capacity, the design of the grinding circuit may vary significantly. Typically, the circuit consists of several mills (rod, ball, SAG, AG) in series and/or parallel with a number of classifiers and sumps at appropriate locations. The goal of the grinding section is to reduce the ore particle size to a level that enables efficient separation between gangue and precious metals in the subsiding processing step. The trade-off between quality and quantity has to be made. It is also crucial to execute this process step at the lowest possible energy and grinding media consumption.An optimal grinding process controller must manage to maintain a given fresh feed level while keeping the product size within a given range without violating any constraints such as power, torque or load limits. To accomplish the aforementioned, it is necessary to manipulate the ore feed rate, water feed rate and the mill speed. The most significant disturbances adding another degree of complexity to this control problem are ore hardness and the amount of circulating load."

Jan 1, 2016

By Adrian Dance

Newmont Ghana Gold Limited?s Ahafo operation have been working with Metso Process Technology & Innovation (PTI) since early 2009 to increase mill throughput from a combination of controlled blasting practices and optimised primary crusher and grinding circuit conditions. For such Mineto- Mill projects, PTI?s methodology is termed Process Integration & Optimisation (PIO). Ahafo operate a SAG mill, ball mill and pebble crusher (SABC) circuit that processes a range of primary ore of varying hardness from different pits which is blended with soft oxide material. The PTI study focussed on ball mill limited material from the Apensu open pit. Following a benchmarking study of all blasting, crushing and grinding practices in January 2009, PTI recommended changes in both blasting and crushing conditions in order to generate a finer feed size to the SAG mill. Additional operating changes in the grinding circuit were recommended. A series of trials were conducted in November 2009 where three blasts were fired using a different blast design (hole diameter and explosive type) in the same area of the Apensu pit as the benchmarked material in January 2009. Top and bottom benches (or flitches) from each blast were sent exclusively to the grinding circuit and the material was tracked using PTI?s SmartTag? system. The results from the six trials showed a significant increase in primary ore throughput at a reduced blend of oxide material. Ahafo have since standardised on these modified blasting conditions for all Apensu ore zones and have been able to sustain higher throughput compared to historical performance on similar material. This paper summarises the phases of the PIO project, the changes made in operating practices and the outcomes of the blasting trials that validated the predicted increase in mill throughput.

Jan 1, 2012

By Avi Nanda, Robert Brandt, Alex Piatkiewicz, David M. Jones

In 2010 the United States Environmental Protection Agency (UESPA) revised the National Ambient Air Quality Standards (NAAQS) by lowering the permissible value to a 1-hour average SO2 concentration of 75 ppb. In 2012, the USEPA designated the Miami area as non-attaining for the new SO2 NAAQS. A number of options were studied to assist in bringing the Miami smelter into attainment with the new standard. The chosen solution included: Installation of a large tertiary hooding system over the converter aisle; Hooding of the anode vessels and treatment of the anode gas in a baghouse; Installation of a large 2,325,212 Nm3/hr caustic scrubber to treat the captured converter fugitives and anode off-gases; Installation of a secondary ESP for the tapping fugitive off-gas treatment system; and the continuous scrubbing of all acid plant tail stack gases. The modifications have reduced smelter SO2 emissions by 85%, achieving a world class SO2 stack emissions rate of 0.45 kg of SO2/tonne Cu. INTRODUCTION The Freeport McMoRan Miami smelter has been previously described in literature (Steinborn, Pasca, Sallee, Binegar, Bhappu). For the sake of brevity a brief description is given here. The Miami smelter is located 129 km east of Phoenix, Arizona near the town of Miami, Arizona. The smelter was established in 1915 and has undergone a number of process upgrades and modernizations over the years. The present smelter consists of an Isasmelt furnace, an electric settling furnace, four Hoboken converters, two anode refining vessels & one casting wheel; and one double contact sulfuric acid plant. Concentrates are railed & trucked to Miami from four Freeport McMoRan mines located in Arizona & New Mexico. The wet concentrates, typically containing 10% H2O with a Cu/S ratio of 0.85, are smelted in an Isasmelt furnace to a matte grade of 58%. The entire output from the Isasmelt is laundered into an Elkem electric furnace (originally installed in 1972 as the primary smelting furnace) for separation into matte and slag. Slag containing 0.85% Cu is skimmed from the electric furnace and discarded. Molten matte, containing 60% Cu, is tapped from the electric furnace and processed in one of four Hoboken converters to produce blister copper. Two anode refining vessels further refine the blister copper before the final product is cast on a single, 30 mold, casting wheel. All of the anodes produced at Miami are shipped to the Freeport McMoRan electrolytic refinery in El Paso Texas for refining into cathode copper. Smelter off-gases from the Isasmelt, electric furnace and Hoboken converters are combined and treated in a double contact acid plant to produce sulfuric acid. Acid produced at Miami is internally consumed at Freeport McMoRan mines in the region.

Jan 1, 2019

By B. D. Frater

Geometallurgy or process mineralogy is an integrated part of the scoping, pre-feasibility and feasibility phases of a project as well as an existing operation. A well planned and executed geometallurgical testwork programme during the early phases, will result in a more accurate decision making process during the selection phase. The better this integration between geological, mining and metallurgical data gathering during the early phases, the more accurate the predictions will be with regards to throughput and recovery during modelling and process and equipment selection in later phases. This will enhance and improve the mine and process scheduling and subsequent NPV. Geometallurgical information gathered during plant operation and testwork can for example be used to statistically model the pit optimisation, plant throughput and optimise the plant for certain feed material (characterised by statistical models).

Jan 1, 2017

By E. Fiset, T. Hennebel, F. Verbruggen, A. Prévoteau, K. Rabaey

Arsenic (As), bismuth (Bi) and antimony (Sb) are known to affect the quality of copper deposits in copper electrowinning operations. The codeposition of As was previously believed to occur only at current densities far exceeding the range of typical current densities for copper electrowinning. In this study, we investigate the copper electrodeposition on different pretreated stainless steel (SS) substrates from bleed electrolyte in galvanostatic mode at –45 mA/cm². Scanning electron microscopy (SEM) micrographs illustrate that during the initial phases of copper nucleation and growth, the current density was locally increased due to the pretreatments. It was reasoned that the codepostion of As could possibly occur in normal electrowinning conditions, but the risk can be substantially reduced by good SS substrate handling and maintenance practices. INTRODUCTION The presence of As, Bi and Sb is known to have a deleterious effect on the copper cathode quality in copper electrowinnings (Hiskey & Maeda, 2003; Hoffmann, 2004; Xiao, Cao, Shen, & Volinsky, 2012; Xiao, Cao, Mao, Shen, & Ren, 2014; Jafari et al., 2017). They are known to influence both the chemical and physical quality of the copper as they can contaminate the copper (Jafari et al., 2017) and affect the copper deposit structure (Hiskey & Maeda, 2003; Kim, Kim, & Chung, 2009), which contributes to a degraded market value of the copper (Tuddenham, 1984). The incorporation mechanisms of these impurities are believed to occur mainly through slime inclusion (F. Xiao et al, 2012) and electrolyte inclusion (Hiskey & Maeda, 2003). Other studies suggested that codeposition of these impurities is possible by their standard reduction potential being close to the one of copper (Xiao et al, 2014). Hiskey and Maeda (2003) investigated the copper electrodeposition on a copper electrode substrate in Cu electrolytes with a Cu, H2SO4, As, Bi, Sb composition representative for commercial copper tankhouses. The combination of voltammographic techniques and Auger electron spectroscopy showed that As was the first impurity to be electrodeposited from this electrolyte, yet at potentials where the limiting current density of the copper electrodeposition reaction is exceeded. The copper tankhouses usually operate at a current density ratio of 0.3 to the limiting current density in order to achieve tolerable copper quality deposits. The codeposition of As could be considered impossible in this current density condition. However, it is known that during the initial phases of electrodeposition on foreign substrates, a substantial part of the reaction proceeds by growth of individual nuclei where the current density is locally high and diffusion limited (Radisic, Ross, & Searson, 2006). Furthermore, it was observed that copper nucleation on TiO substrates occurred preferentially in the scratched oxide free areas which could serve as parts with high localized current densities (Chang, Choe, & Lee, 2005).

Jan 1, 2019

By Rob Kelso

The PISCES Goals ? To conduct research and develop programs to enable and promote planetary surface exploration ? To host international tests and technology demonstrations at the PISCES Test Site. ? To promote STEM education, inspiring students by connecting Hawaiian culture to space exploration and settlement. - economic and workforce development ? To involve the commercial sector, spinning off technologies to help the local Hawaiian economy. ? To develop a full-scale, technically valid, analog lunar/Martian outpost on Hawai`i Island.

May 1, 2013

By D. Eriksen

Zero Emission Gas power, ZEG, is a novel concept where a high temperature solid oxide fuel cell (SOFC) is integrated with a reforming reactor producing hydrogen from natural gas through Sorption Enhanced Steam Methane Reforming (SESMR). The SOFC is used as a high temperature heat source for regeneration of the CO2-absorbent. Moreover, by using part of the produced hydrogen as fuel for the SOFC, the waste heat of the process is considerably reduced. Thus, the process has a very high thermal efficiency and produces both electricity and hydrogen from natural gas. In addition, a stream of pure CO2 is produced in the regeneration step and can be deposited or used commercially. Initial cost estimates indicate a cost of electricity and a cost of hydrogen well below today&apos;s prices. A small (1kWel + 1kW H2) demonstration set-up is under construction and experimental results and related research will be presented. This set-up comprises one 2.5kWth H2 SESMR-reactor (about 0.85 Nm3/h H2) operating batchwise with dolomite as the CO2-sorbent. The reactor developed is designed like a parallel plate heat exchanger where the mixture of sorbent and reforming catalyst is packed between the heat exchanging plates. The demonstration set-up includes a 1kW SOFC operating in a continuous mode. The set¬up will therefore demonstrate continuous simultaneous hydrogen- and electricity production, but cannot demonstrate simultanuous electricity- and CO2-production. The set?up is well equipped for on-line monitoring of gas composition, flows and temperatures. This important part of the demonstration set-up is developed and provided by Christian Michelsen Research (CMR). A minor part of the project is the development of a continuous circulating fluidized bed SESMR-reactor system and in another related project the focus is on the development of more suitable sorbents. In these two projects co-operation with University of British Columbia and Lousianna State University, respectively, is highly appreciated.

Jan 1, 2005