Search Documents

By John H. N. Yen, James M. Marquardt, Larry H. Heflin

INTRODUCTION On February 17, 1995, WMATA Contractor J.F. Shea holed through the last segment of rock tunnels of the planned 103-Mile Rapid Transit System for the Washington Metropolitan Area Transit Authority. Through the joined efforts and cooperation between the owner and the contractor, the project was completed on time and within budget. The Glenmont extension is on schedule to open in Mid-1998. The complete 103-mile system is scheduled to open in 2001. WMATA’s earlier 19 miles of rock tunnels had been done since 1976 ? By drill and blast with heavy horseshoe steel sets, sets with shotcreting over wire-fabric by TBM and NATM. All rock tunnels were primarily in metamorphic gneiss and schist, part of an east coast lithology that outcrops in a band running from below Richmond, Va. To above New York City. The 5,400 ft. long twin six meter tunnels of the Glenmont line had been earlier de-signed in 1979 by URS of NYC using Jenny Engineering of Pittsburgh, Pa., as a tunnel design specialist sub consultant. Jenny had provided two alternative designs, one conventional drill and blast horseshoe and one for Tunnel Boring Machine. Funding considerations had put the design on the shelf and it was clear that the state of the art had led to improved design methods in the intervening years. Before URS was tasked to update their design in1992, the Authority reviewed its earlier hard-rock experiences in light of the funding mandate to complete each segment on a limited budget and an expedited schedule. Many factors considered and many opinions were in leading to a final decision to drop the earlier designs and redesign for a single designated means of tunneling. That method was the New Austrian Tunneling Method. The NATM had been used earlier on WMATA for both soft-ground and rock tunnels. In the public’s eyes the NATM had become inextricably linked with the use of PVC’s and filter material enveloping or partially enveloping the underground structures to give the holy grail of tunnels, a water-tight structure. Although this link of waterproofing methods with excavation and support methods was essentially severed, a general feeling of their interdependence no doubt helped lead to acceptance of the NATM decision because of the waterproofing design that accompanied it. The Authority decided to drop the TBM and conventional options and provide bid documents for NATM only. URS asked LAW Engineering of Atlanta to provide the NATM design of the tunnels and associated shafts.

Jan 1, 1997

By M. McPherson, P. Mousset-Jones, G. Danko

Calculation of the sensible heat transfer between the rock surface and the flowing air in an underground airway is still fraught with problems. There are only a few results available in the literature for the calculation of the convection in tunnels with naturally rough surfaces. Some of them are purely empirical, while others use a theoretical approach, based on the analogy between heat and momentum transfer, expressing the heat transfer coefficient as a function of the friction factor. A review and evaluation of these results are presented. The heat transfer equations obtained using the different assumptions, vary over a wide range, so that experimental results are needed to determine the formulae and constants applicable to mine airways. In situ measurements of the "physical" and "technical" heat transfer coefficient carried out in deep mines are described. The statistical distribution of the convective heat transfer coefficient on rough surfaces, as well as the regression between the Nusselt and Reynolds numbers in the turbulent flow region, are presented. Radiative heat transfer between the surface and the moist air flowing in a duct of relatively large hydraulic diameter has been taken into account during evaluation. The results will be a definite refinement of those calculations presently used in mine climate simulation models.

Jan 1, 1987

By K. Gorazda

The population growth, urban and industry development cause the increased pollution with different substances, which contain phosphorus. It contributes to the increased demand for its compounds, increasing the use of its natural resources, which is considered to be the most accessible source. The forecasts regarding the world natural reserves of phosphorus deposits are saying that more than 50% of resources used currently will be exhausted within next 60-70 years (Steen, 1998). European Union formulated its goals regarding the waste management in 1990. Its main rules include prevention of waste generation, recycling, reuse of waste as the raw materials in technological processes, separate collection and optimization of final removal. The phosphorus recovery from waste is realized currently in many ways: directly from the waste water stream in sewage-treatment plant, from the sewage sludge, from animal waste, industrial waste and other emissions from industry (Przewrocki et al., 2004). According to the rules of cleaner production the waste should be treated as the source of resources for the production of products with full value (Kowalski, 1998).

Jan 1, 2005

By Gábor Antal, József Bõhm, Barnabás Csõke

From the waste material of the production of aluminium foil aluminium pigment is produced for the paint industry by grinding it in white spirit. During grinding 1-2 % iron impurity gets into the product, weakening its quality, from the wear of the mill armour and the grinding bodies and from the contamination of the raw material. For deironing the product, a stage-operated electrically induced magnetic filter separator was developed and put into operation. The separator was sited in an explosive environment and therefore required a special design and safety system. The paper describes the results of the development work. the device that was developed, the safety system as well as the results of and experiences with the operation of the separator.

Jan 1, 1995

By G. Y. Li, D. Farahmand

The dilemma of a numerical analyst not only concerns the problem of modelling the non-linear behaviour of intact rock, but also the non- linearity contributed by structural discontinuities. In this light, it is the intention of this paper to examine some aspects of the non-homogenity and structural discontinuities of rock and incorporate this behaviour into boundary element numerical solution. Non-homogeneous material is considered piecewise, thus homogeneous and is modelled by using sub-regions. The Mohr- Coulomb failure criterion is employed to model the non-linear behaviour of the major discontinuities. A computer program is developed based on the procedure for combining the direct boundary element method and the displacement discontinuity method. A linear element type is employed in the formulation of numerical solution. The computer program is used to study the stress distribution in a gold mine.

Jan 1, 1986

By E. D. Attanasi

Exploration for non-fuel minerals has declined since 1988 as recessionary pressures have slowed growth in the industrialized economies. By most accounts, however, 1990 expenditures were still significantly greater than the low levels experienced in the mid-1980s. The Persian Gulf crisis introduced instability in energy prices and greater uncertainty into an already cloudy economic picture. As 1990 unfolded, the US savings and loan problems spread to the commercial banking system, leading to the failure of several major US commercial banks. The Japanese stock market also suffered significant losses as Japan's Central Bank raised interest rates. The Soviet Union experienced shortages of food and other basic items. Its government faces resistance to changes leading to a market economy. Individual Soviet republics also are seeking more control of their own destiny. The cost of German reunification, in terms of the capital required to bring the east's infrastructure and industrial base to western standards, also appears to have been underestimated.

Jan 1, 1991

By Patrick J. Doig

The NS9 Drop Shaft contract formed part of the Waste Pollution Abatement Program (WPAP) conducted by the Milwaukee Metropolitan Sewerage District (MMSD). The contract involved the construction of two shafts, a deaeration chamber and connecting tunnel, and ancillary facilities. Portions of the construction were located in saturated overburden where dewatering was prohibited. Ground freezing was utilized for temporary support of the excavation. This paper concentrates on the freezing system and the excavation of frozen ground, with particular emphasis on the use of mechanical cutting equipment, including a raiseborer and a roadheader.

Jan 1, 1991

By Zhen-lu Zhao

The manipulators possibly used in underground mining must deal with unpredictable obstacle while keeping certain positions and orientations of end effector, and in some cases, are required to possess redundant joints in order to be more flexible. This kind of manipulators might be fitted with jumbo drill or platform as auxiliary to potentially deal with some utility works in versatile way, such as installing rock bolts, guniting, blasting, charging, surveys and measuring work, etc.. This paper describes numerical procedures of performing inverse kinematic problems for redundant manipulators .The procedures, based on the generalized pseudoinverse of Jacobian matrix, are developed to lead to kinematic solution at both singularity and ill conditioning, and to guarantee continuous sequence of positions of the end effect or. Furthermore, the solution to optimization and obstacle avoidance is investigated. A numerical example is shown to illustrate the approach.

Jan 1, 1989

By R. K. Mehta

A review of the literature reveals that methods for simulating the coupled behavior of size reduction and liberation are limited to binary mineral systems containing one composite particle class. The aim of this paper is to describe the development of a mathematical model to simulate such behavior for binary and ternary systems containing multiple classes of composite particles. A modified Levenberg-Marquardt algorithm and a finite difference Jacobian are used in conjunction with the developed model and a set of constrained equations to estimate all kinetic parameters. This estimation scheme is validated for a binary ore (sphalerite-dolomite) with five composite particle classes using experimental data.

Jan 1, 1989

By Joseph M. Keane

Introduction The English word "sedimentation" is derived from the Latin verb "sedere" meaning to sink down. As a mineral processing unit operation, sedimenta¬tion has been defined as the separation of a suspension into a supernatant clear fluid and rather dense slurry containing a higher concentration of solid (Brown, G.G. 1960). Sedimen¬tation has been historically subdivided into thickening, which has the primary purpose of increasing the solids content of one of the thickener prod¬ucts relative to the feed stream, and clarification, which has the primary purpose of removing solids from the feed stream to produce a product essentially free from particu¬late matter. There is no absolutely precise distinction between these subdivisions and in certain applica¬tions, both objectives can be accom¬plished. Major Design Factors The capacity of conventional metal¬lurgical sedimentation devices is a function of slurry throughput and its attendant settling rate. Important factors, recognized by early investigators (Taggart, 1972), which influence the settling rate of a given metallur¬gical slurry include: Feed dilution or solids-liquid weight ratio Size and shape of the particulate solids Specific gravity differential between the solids and liquid phases Presence of electrolytes and/or flocculants Pulp viscosity Slurry temperature In addition to the foregoing histor¬ical factors, recent investigators have noted (Pearse, M.J., 1977) that other parameters which may have an influence upon settling rate and, thereby, thickener performance include: Method of flocculant application Particle size distribution Particulate wetting characteristics Feeding arrangements Rake speed and type Existence of convection currents Wind disturbance Evaporation All of the above factors should be examined and the effect upon thick¬ener performance brought about by manipulating the factor over the expected operating range should be determined if performance optimization is desired.

Jan 1, 1986

By D. Murray

"The Mine Improvement and New Emergency Response (MINER) Act included the need for improved chemical technologies to address respiratory protective device inadequacies and refuge alternative development. The National Institute for Occupational Safety and Health’s (NIOSH) National Personal Protective Technology Laboratory (NPPTL) invests in research and development to improve the carbon dioxide (CO2) scrubbing technologies built into these mine safety systems. Testing at NIOSH NPPTL is performed using a custom-designed test system containing a chemical reactor and sensors in a constant flow of simulated expired breath to evaluate chemical performance for the scrubber materials. Current testing procedures focus on device duration or capacity, but do not report criteria needed to effectively optimize chemical performance. In this presentation, testing results which identify the chemical performance roles for CO2 scrubber components will be reported, and specific component chemical activities will be linked to both duration and CO2 absorption capacities. Chemical components being evaluated include hydroxyl, superoxides, metal, and amine active sites, distributed in salts, zeolites, metal-organic frameworks, and microporous materials. INTRODUCTION CO2 absorbents and oxygen sources are at the heart of closed circuit breathing air supply systems used in mining escape and rescue operations. CO2 absorbent technology was first developed for diving rebreathers and has been in use for over a century. Typically these devices include a soda lime formulation of pellets in the 8-12 mesh range. Larger 4-8 mesh particles are used in medical grade “low-flow” applications, since these particles present a lower flow resistance regime more amenable for use with resting individuals. Potassium superoxide and lithium hydroxide formulations are also used, where in each case the formulations involve bulk solid pellets or materials affixed to surfaces. CO2 capture technologies are now under intensive study in the energy and automotive industries, where the pursuit of optimal combustion processes has led to the development of new materials to capture, convert and store CO2, oxygen and carbon monoxide gases. Recent advances in nano-structured and high surface area catalysis have produced novel materials demonstrating chemical performance improvements in these industries, and these improvements may now also be adapted to enhance chemical efficiency and performance in escape and rescue devices. Higher surface area materials offer promise for improving the efficiency, or decreasing the burdens associated with the use of closed circuit respiratory protective devices containing CO2 absorbents. Novel chemicals that display advantages in chemical performance or decreased burden will be examined for inclusion in developing systems such as the next-generation closed-circuit mining escape respirator or refuge alternatives."

Jan 1, 2018

By F. Aurelian

The development of the uranium mining industry in Romania started in 1950. The exploitation of Bihor region, one of the most important metallogenic zones of the country, began in 1962. Uranium exploitation activities were ceased in 1995 due to the exhaustion of the ore deposits. Between 2001 and 2002, due to the entire mining zone closure, ecological rehabilitation and decommissioning was initiated. The proposed solutions, concerning terrain, equipment and buildings utilization were elaborated according to the guidelines of the Romanian Environmental and Nuclear Authority.

Jan 1, 2006

By Jorgen Elbrond

Before and in the early stages of industrialization, mining was the undisputed leader in technology. It represented the high-tech of the time. Early mechanization bears witness to that. Hoisting and rock breaking driven by waterpower are such examples. The mines' use of the steam engine was a major incentive to its development. By these means new mines could be opened and more metal supplied. Understanding of systems was essential for miners when shaping the infrastructure of the mines for the transportation of ore, material and men and for the evacuation of water and for ventilation. The irrigation systems of ancient mines are such examples. However, with the industrial revolution other more specialized branches of industry advanced further, and the mines became users of other industrial branches technologies. The mining industry had, however, always been quick to recognize a good thing and use it, when time was right. But, compared with other branches of industry, the mining industry has the disadvantage of working in a rugged environment with (and actually inside) a raw material which is abrasive and highly variable with respect to mechanical properties. This determines the rather high unpredictability of mining machines' performances and their low availabilities and explains a part of the delays in introducing technological advances.

Jan 1, 1989

By William J. Attwooll

The development of gold heap leach projects in the Cripple Creek, Colorado, mining district has required utilization of heap leach pad sites other than relatively level natural ground. This paper describes the construction of a heap leach pad adequate to accommodate 907,000 tonnes (1,000,000 st) of ore over the surface of a tailings pond constructed during previous milling activities at the site. Based on the design parameters and the observed behavior to date, it has been found feasible to construct a major heap leach pile on the surface of a conventional tailings pond.

Jan 1, 1987

By R. M. Cox

Pneumatic coal loading and conveying systems provide alternative methods for the safe and efficient mining of the thin, high-grade coal seams found in the Southern Appalachians. Pneumatic systems eliminate most of the health and safety hazards associated with the operation of conventional mining and haulage equipment in small low-coal mines by removing powered mobile equipment from the mine. Ventilation is also improved by the coincidental removal of gas and respirable dust from the mine by the operation of the pneumatic loading and conveying system. Other significant advantages of pneumatic coal recovery systems are relative simplicity, operating flexibility, low capital cost, quiet operations, environmental benefits and ease of automation. The design considerations and field evaluations of experimental prototype pneumatic coal loading and conveying systems installed and operated in small thin-seam mines are presented in this paper. In addition, fundamental design criteria and recommendations for the installation and operation of a variety of pneumatic coal loading and conveying systems that offer alternative coal-recovery systems that alleviate the serious health and safety concerns of current small mine operations are proposed.

Jan 1, 2000

By Mucella Ersoy, Nese Celebi

Management Information System (MIS), is a system using formalised procedures to provide management with appropriate information to make timely and effective decisions. Before developing MIS, first functions of the organisation should be defined and grouped into subsystems. After determining the information required and produced by each system and interaction between subsystems, the related data resources should be structured into a series of databases and files. In this study, the MIS developed for Soma Open Pit Mines, Turkey is described in this respect. First, analyses of the existing system including user requirements and scope of the system are given. Then the designed information system, its subsystems, interaction between subsystems and system structure are presented in detail.

Jan 1, 2002

By James A. Everts

Calcined bauxites are classified by their major end uses - abrasives and refractories. Target properties are dictated by application and processing requirements. The chemical and physical properties of premium grade calcined bauxites are far more stringent than metallurgical bauxite and this limits the sources and availability. Premium grade calcined bauxites are considered to be strategically critical to the industrialized countries of the world. Subject to disruptions in the key source countries, adequate supplies of premium grade calcined bauxites are anticipated in the foreseeable future.

Jan 1, 1984

By Z. T. Bieniawski

In the past 15 years, rock mass classifications have experienced unprecedented development and have emerged as powerful practical methods for assessing ground conditions and tunnel support. Such methods as the RMR System (Geomechanics Classification) and the Q-System have provided many advantages over the classical Terzaghi rock-load method introduced in 1946. These new classifications have found wide applications all over the world but some doubts have been expressed and shortcomings pointed out. The author, who developed the RMR System, takes a penetrating look into the promises and the pitfalls of modern rock mass classifications. He dispels some misconceptions and shows how rock mass classifications can serve as effective and dependable design aids in tunneling.

Jan 1, 1987

By F. J. Susko

The US Bureau of Mines is using Fourier-transform infrared (FT-IR) analysis to investigate the bonding mechanisrn that occurs during the dewatering of clay slurries. High-molecular-weight polymers are used as flocculating agents in these processes. This investigation presents the results of an FT-!R study of calcium-exchanged montmorillonite treated with polyacrylamide (PAM) and polyethylene oxide (PEO). Both thin film and attenuated total reflectance (ATR) spectroscopic techniques were employed to study this clay polymer system. Results suggest PAM is adsorbed to the clay via the nitrogen atom of the polymer. A waterbridge is involved in the bonding between the clay at d PEO. Evidence also suggests that PEO may be adsorbed directly onto the surface of the clay.

Jan 1, 1991

By S. K. Kawatra, T. C. Eisele

Under normal conditions, a significant amount of pyrite is recovered in the froth during flotation of high-sulfur coal. To reduce this pyrite recovery, it is first necessary to determine the primary recovery mechanism, because different measures are required for reducing entrainment, locked particle flotation or true hydrophobic flotation. In this paper, evidence is presented that suggests that hydrophobic flotation is not the major mechanism for recovery of liberated pyrite; instead, the bulk of the recovered pyrite results either from simple entrainment or from being physically locked with floatable coal particles.

Jan 1, 1993