Search Documents

By J. Chia, M. H. Kobler, J. Cheung, M. J. Robison

INTRODUCTION The Lake Merced Transport is being constructed as part of San Francisco's Clean Water Program. The Clean Water Program, which began in the early 1970's, is designed to control wet weather, storm sewage overflows into the Pacific Ocean and San Francisco Bay. To accomplish this goal, a system of large underground storage and transport facilities, pump stations, modernized treatment plants, and outfalls is being built. By 1991, eighty percent of the system had been completed and was in operation. One of the remaining projects for the Clean Water Program is the Lake Merced Transport. The Lake Merced Transport is located in the extreme southwestern portion of San Francisco, as shown in Figure 1, Project Location. The transport will convey dry weather flow from the existing Lake Merced Pump Station to the Westside Pump Station. During wet weather, the transport will fill with sewage and runoff, with a storage capacity of 36 million liters. The Lake Merced Transport was expected to be excavated entirely within the Colma Formation, an alluvial deposit consisting of weakly cemented sand. Once excavation of the access portal at the Sloat/Great Highway parking lot began, it became evident that a portion of the tunnel would be excavated through beach/dune sand. Based upon the expectations of the Geotechnical Design Summary Report (GDSR), encountering beach/

Jan 1, 1993

By Richard V. Good, John B. Harvey, Lloyd S. Jones

INTRODUCTION The term "Rapid Underground Excavation" is generally associated with high speed tunnel advance with large volumes of excavation, and indeed this is the type of work for which most of the recent innovations in methods and new machinery have been developed. However, the term applies as well to any underground excavation process that results in an earlier project completion than would be expected with conventional methods, and hopefully with a decrease in total unit excavation cost. Often significant progress has been made during the primary stages of an underground construction project and then an inordinate amount of time and effort has been expended on small units of "miscellaneous" excavation which has delayed the overall project completion and escallated overall unit costs. Construction at the Nevada Test Site of the Atomic Energy Commission for underground testing frequently requires significant amounts of so called "miscellaneous mining" such as short access drifts, cross cuts, alcoves, niches and concrete keyways. Many of the keyways must be excavated without disturbing the rock beyond the excavation lines and construction scheduling often dictates that much of the work must be accomplished without disturbing sensitive electronic equipment already installed. In order to cut down on lengthy and costly delays required for the tedious manual excavation of much of this miscellaneous mining, a market search was made for suitable mechanical excavation equip-

Jan 1, 1997

By Jonathan M. Pachter

Introduction The Bailey mining complex is located in Greene County, PA, in the Talley Run valley. It includes two Pittsburgh No. 8 seam deep mines (Bailey and Bailey No. 2), a coal preparation plant, and two refuse areas. Clean coal is shipped from the complex by way of a 24-km (15-mile) rail spur. It con¬nects to the Monongahela Railroad in Waynesburg, PA. In early 1981, Consolidation Coal Co. (Consol) began a permitting effort aimed at building the mine. Construction began in Dec. 1981, less than six months after the first application submittal. Clean coal was produced by the Bailey preparation plant in Sept. 1984. Several factors allowed quick permitting at Bailey. Effective project planning, including early formulation of a project planning team, and identification of red flag issues helped. So did innovative responses to environmental questions, and development of environmentally sound project designs. Forming a project planning team Consol management decided that Bailey mine construction had to begin in late 1981. A project permitting team was immediately formed to see that this goal was achieved. Team members included a project manager and personnel from Consol's engineering, environmental, and operating departments. Communications among all team members was crucial in obtaining the various state and Federal environmental permits. All project permitting team members participated in weekly meetings during application preparation. Discussions at these meetings ranged from recent public contacts, to application content, to environmental design considerations. Establishing a project manager was critical to the team's success. The project manager was responsible for seeing that permit acquisition, facility construction, and operation of the mining complex proceeded on schedule. The project manager had the final word, mediated disagreements, and frequently served as project spokesman to the public. Identifying red flag issues Red flag issues are those environmental factors with the most potential for delaying the schedule or stopping the project. The first red flag issue identified was organized local opposition. This opposition had completely derailed a US Soil Conservation Service proposal to build a multipurpose dam on Enlow Fork, a short distance

Jan 9, 1985

By Thomas D. Kaufmann

Introduction Mining has always been sensitive to the fluctuating income of downstream customer industries. The industry is now becoming more vulnerable to booms and busts as economic pulsations increase and demand for mining products shows little or no long-term growth. As the general economy has become more cyclical in the last decade, the capital-intensive primary industries have become more aware that timing as well as preparation of survival plans are vital in investment decisions. Strangely, however, some of us have not yet included the business cycle in our feasibility studies. Cyclic prices and volumes and fluctuations in profits and cash flows do not fit our linear models. The increased cyclical nature of our economy is recent and poorly understood. Forecasting peaks and troughs is still more an art than a science. Nevertheless, avoiding business cycle parameters can lead to error in value estimation and contingency planning of new projects. Metal and Mineral Industries More than half the iron and steel, aluminum, copper, lead, zinc, manganese, tin, nickel, molybdenum, cobalt, and chrome that we mine, smelt, upgrade, and recycle goes to construction, transportation, capital goods, and consumer durable industries. All are cyclical. Their products are consumed slowly, so replacement can be postponed in recessions. Purchases of such goods are usually financed by debt, and their customers are sensitive to highly cyclical changes in interest rates. During prosperous periods, people tend to buy capital goods despite high interest rates. Upstream industries also tend to be whipsawed by inventory cycles. With high interest rates and good transportation, downstream fabricators can lighten their inventories during recessions. They know that upstream suppliers can deliver supplies and raw materials immediately, And, with the advent of electronic accounting, the fabricator with timely inventory information can afford to hold fewer contingency stocks. Likewise, when recovery returns, inventories surge back through industry pipelines, accelerating demands on primary supplies. The price elasticity of most primary products is low. Their share of the value of finished products of the industries they supply is generally small. The 60 kg (130 lb) of aluminum in a car is vital. But whether it costs $80 or $130 will not visibly influence the demand for an automobile. With low elasticities of demand, the primary producer is hit with decreases (or increases) in prices and in sales volume, during recessions as well as recoveries.

Jan 6, 1984

By Kim W. Wright

Introduction Mining operations require maps for each phase of project development. Engineering plans, cross-sections, and isometric drawings are also needed. Maps are used for geologic interpretation, reserve estimation, permitting, property acquisition, site studies, development work, and production. Maps and drawings are essential to mining. They provide needed information. Generating these products, however, requires many manhours. The filing and organization of maps and drawings is cumbersome, due to their size. Major map changes can necessitate the production of entirely new documents and, thus, additional manhours. The volume of maps and drawings generated in the life of a single project can be extensive. For example, some utility companies have data bases containing more than a million individual maps (one reported eight million). These problems were considered necessary evils in the past. Now, with the automation of map and drawing production, improvements can be realized. Computer-aided mapping and design offers a new approach for the production, management, and storage of drawings and maps. This approach promises benefits in time management, productivity, efficiency, and flexibility. In all economic projects, the bottom line is cost reduction. And implementing computer-based mapping and design techniques can lower costs and increase project profitability. AM/FM/CAD/CAM Automated Mapping/Facility Management (AM/FM) and Computer-Aided Design/Computer-Aided Manufacturing (CAD/CAM) are becoming buzz words in the engineering world. Most relevant to mining are the concepts of AM and CAD. These terms relate to the application of computers, specifically computer graphic technology, to mapping and design. CAD refers primarily to the design of components and structures in two and three dimensions. But it can apply to the three dimensional modeling of mine workings, ore bodies, and geologic structures AM refers to the automation of conventional map production. AM/CAD systems use computers to store, manipulate, produce, and update drawings and maps in two and three dimensions. Ideally, the calculating capabilities of computers are also used in conjunction with design and drawing generation, offering capabilities not available with conventional, manual mapping and design processes. To better understand concepts associated with AM and CAD applications, the understanding of a few computer-related terms is necessary. Table 1 explains some of these terms. System Features The capabilities of AM/CAD systems are based on viewing transformations. These are the basic, manipulative tools by which AM/CAD packages generate visual representations of data. Examples include the rotation of a three-dimensional object through space, the expansion or contraction of maps to fit a given scale, enlargements of small areas on maps or drawings for detailed viewing, and the generation of cross-sections from three dimensional data. AM/CAD systems incorporate data base management in their architecture. This allows a user to modify, move, delete, or manipu-

Jan 6, 1985

By D. C. Torre

Since the early 1960s, there have been efforts to develop and produce reliable continuous haulage systems capable of taking the full output of a continuous miner and transporting it, in one continuous flow, from the face to the tipple. The majority of the successful continuous haulage systems were placed in operation in the early 1970s. These were all of the bridge conveyor type. They usually consisted of bridges and mobile bridge carriers (MBC) attached at the inby end to the continuous miner and at the outby end to the panel conveyor itself. These successful bridge conveyor continuous haulage systems are either of the belted or chain type. The most successful belt type continuous haulage systems are those manufactured and marketed by the Long-Airdox Co. Until early 1977, Jeffrey Mining Machinery Division manufactured and marketed the most successful chain conveyor type haulage sys¬tems. In 1977, Long-Airdox reentered the market with a chain-type system to complement its belted system. The original bridge-type continuous haulage system was introduced to the coal mining industry in the early 1960s by the old Long Co., a predecessor to the current Long-Airdox Co. These original units were of the chain conveyor type. In the early 1970s, there were also developments in continuous haulage, employing different material handling media. These in¬cluded the Serpentix, a flexible type belt, introduced by the Joy Manufacturing Co. There was also a serious attempt to introduce hydraulic-type continuous haulage by Consolidation Coal Co. and Conoco Research. Despite some startling successes, particularly with the bridge-type haulage systems, the general and widespread application of continuous haulage has eluded the mining industry. Some of the problems are related to underground conditions; others to people, both management and labor. One of the greatest obstacles to universal success continues to be the difficulty of accepting the philosophy as well as the machinery of continuous haulage. Nevertheless, efforts continue to spread the success of commercial and viable systems in the industry. There is also effort to improve on these systems, and on methods for their successful use. In addition, efforts continue, with private and public support, to develop new types of continuous haulage equipment and systems. Bridge Type System Developments Because they have already been successful in some US and overseas mines, new developments in bridge-type systems will first be touched on. The Long-Airdox Co. has continued to improve both its belted and chain continuous haulage system. In the belted system, the company recently introduced a new design that will be mainly applicable in higher coals and in noncoal mining applications, as shown in the accompanying figure. This new system is equipped with 305-mm-diam (12-in.-diam) pulleys in the bridges and mobile bridge carriers, in place of the 150-mm-diam (6 in.-diam) pulleys in the standard system. The modification is designed primarily to improve belt life and keep belt problems to a minimum. An operator, the Clinchfield Coal Co., a Division of Pittston Coal, developed the detaching of the bridge-type continuous haulage system from the miner by placing a mobile bridge carrier at the head of the string. However, Long-Airdox and Jeffrey have now made this an option to their at¬tached-type system. In the US, there are many chain type haulage systems detached from the miner with an extra MBC at the head. There are two such belted systems

Jan 7, 1982

By Wallace W. Roepke, James C. Church

Introduction The history of mining machine development has been and is one of "bigger is better." While this may not always be true, it is currently the only approach open to machine designers without specific in situ cutting force information. The US Bureau of Mines has tried to modify this approach by supporting research, both in the laboratory and in field tests, that demonstrates that bigger is only better if the equipment is used correctly. In-house research has shown conclusively that deeper cutting reduces both dust and energy (Roepke, Lindroth, and Myren, 1976). This approach has been applied to a large Lee-Norse (LN456) continuous mining machine, which confirmed that slow deep cutting is beneficial and does not have a negative effect on production (Black and Rounds, 1977; Black et al., 1978). Specific in situ engineering data needed on coal cutting forces have not, however, been obtained by field tests with the LN456. Although the machine was instrumented to obtain data on one seam, it would be impractical to move the machine from mine to mine. It became apparent that a portable, easy to use device was needed for obtaining coal cutting forces in situ. Such a device could provide the engineering data needed by manufacturers, the site-specific cutting information needed by operators, and a field research tool to establish correlation with laboratory cutting tests. Design and Development According to a set of design guidelines established by the Bureau, the proposed device should be able to measure cutting forces directly with standard coal cutting bits, be transportable by two miners, and be self-contained. These guidelines were given to Ingersoll-Rand Research Inc. (IRRI). The contractor performed a rigorous review of 16 existing in situ portable tester designs, none of which could use a standard coal cutting bit to measure cutting force directly. These included a wide range of devices, all of which are discussed in the final report (Banerjee and Wisner, 1982). A series of design tradeoffs were established to satisfy initial design guidelines. The final deci¬sion was heavily weighted by an industry survey to determine the preferred concept from four man¬ufacturers and four operators. To assure ease of use with maximum information, all respondents wanted a linear cutting device that could work in seams down to 1 m (40 in.). The final design choice was between a linear and a rotary tester. The rotary tester would cut on an arc in the same manner as a rotary drum machine. It had several faults, however, that could not be resolved within the scope of this contract. The worst was related to arc cutting (Roepke, Lindroth, and Myren, 1976). Since any bit cutting on arc enters the coal at zero depth, goes to maximum depth only at the horizontal centerline, and exits at zero, maximum cutting force is obtained only at the instant the bit crosses the horizontal centerline. This centerline peak response would require that many replications be made with an arc-type cutter to get reliable force information. The arc-type tester would require extensive face preparation to establish the cutting path and extensive wasted clearing cuts to advance the device for additional layers of cuts. The linear tester could be mounted directly on any face or rib with only minor preparation. By its nature, a linear cut at a constant depth provides multiple peak force data over the length of the cut, thus reducing the required number of replications. The final review of these two major design concepts plus indus-

Jan 9, 1983

By L. P. Hendriks

Consolidated Murchison, the only antimony producer in South Africa, is situated in the northeastern part of Transvaal. Phalaborwa, an important copper/phosphate mining town is situated about 60 km to the east of Consolidated Murchison, on the border of the Kruger National Park. The mine is jointly controlled by Johannesburg Consolidated Investment Co. Ltd. (JCI) and Anglovaal Limited.

Jan 1, 1998

By Paul Culvenor, Brad Gyngell

Ensuring effective management of contractual processes is essential for maintaining profitability and operational efficiency in mining. However, due to limited capacity and resources, sites often struggle to manage these processes effectively, leading to oversights and financial losses. Recent advancements in Artificial Intelligence (AI) offer promising solutions to these challenges. Large Language Models (LLMs), like those powering ChatGPT, now enable machines to understand unstructured data like contracts. These can therefore be applied to address these challenges by taking some of the heavy lifting off of humans. In this paper, we analyze a real-world case study of the application of LLM tools for preventing a $400k contractual issue on an underground gold mine in Western Australia. We provide a gap analysis of the failure modes in existing processes that led to the issue. We then describe the application of LLM tools to flag it early and facilitate a collaborative solution between the operator and the supplier. This includes a comparative analysis of base case vs LLM case to evaluate the impact on project cost and time. Finally, we discuss how the integration of AI can foster improved relationships between clients and contractors across a broad range of potential contractual applications, allowing the time required for collaborative and proactive problem solving.

Feb 1, 2025

By D. D. Potter

ABSTRACT OF ORAL PRESENTATION Extraordinary conditions are often encountered when designing large blasts for in situ mining methods and spatial or innovation techniques are sometimes required. Some of the considerations in designing these large blasts will be discussed with emphasis on those factors that concern powder factor, rock movement and fragmentation. Sources of basic data will be described, along with some of the methods for obtaining these data.

Jan 1, 1977

By P. D. Tomlingson

Senior mining mangers that do not get directly involved in the quality of maintenance performance risk the profitability of their operations. Maintenance is not a stand-alone activity. It requires a production strategy that addresses the total life cycle of equipment from procurement to replacement and assures the fully cooperative, mutually supporting interaction of all mine departments. Only senior managers can assure this happens. This paper examines the strategies, policies and actions required to establish and sustain effective maintenance and the profitability that derives from it.

Jan 1, 2004

By Haydn H. Murray

A hydrothermal bentonite located in the high Sierras in Nevada is being mined and processed to produce a natural dietary supplement. The minerals present are smectite, gypsum, jarosite, quartz, feldspar, kaolinite, goethite, hematite and zeolite. The clay material was analyzed for respirable crystalline silica, asbestiform minerals, heavy metals and dioxin. No asbestiform minerals are present and the crystalline silica, heavy metals and dioxin are all less than the maximums set by Federal and State agencies. The clay material was analyzed chemically for all major, minor, trace and rare earth elements. The geology, applications and analyses will be discussed in the paper.

Jan 1, 2005

By Robert McEwen

Conveyor equipment beyond its prime chronically suffers from a lack of understanding in today's plant environment regularly delivers more material than original designers ever expected. A case in point is a belt conveyor in a major hard rock mine/milling operation asking to bring the unit up to current standards while eliminating spillage and reducing airborne dust. The challenge was to keep the system going by revamping the system while keeping the same footprint and allowing for higher production rate. Thirty years of daily maintenance and dust collection costs have virtually disappeared by the end of this challenging upgrade.

Jan 1, 2008

By J. K. Neathery, T. X. Li, H. Ban, J. L. Schaefer, J. M. Stencel, X. K. Jiang

Pneumatic, triboelectrostatic processing of physical mixtures containing fine (-200 mesh) particulate may have significant application potential in the mining and energy industries. Such dry processing methods, especially for finely comminuted materials, have not been examined in as much detail as wet processing methods nor have been part of the training or education of mining and process engineers. We have examined fundamental and applied physical and engineering factors controlling triboelectrostatic beneficiation of fine-sized physical mixtures, one of which - combustion fly ash - has size, heterogeneity and mineral concentrations typical of those expected in mined minerals. The applicability of dry processing, however, cannot be readily evaluated because of the unavailability of standard procedures for process assessment.

Jan 1, 1999

By MSHA

Not quite a year ago, during a speech to a group of mining professionals in Washington, DC, the subject centered around the long-range importance of conducting research projects and how much that research needs to specifically apply to health and safety matters in our industry. The point was made about the critical need to work together with government, private industry, labor organizations and academia speaking with a unified voice as we all march into the future together. The fundamental benefits of competitive research were mentioned -- to improve our quality of life, to develop our energy resources, to achieve a safe and healthy environment and to ensure long-term economic growth. Very importantly, emphasis was given to the natural link that makes my agency, the Mine Safety and Health Administration, and the National Institute for Occupational Safety and Health -- NIOSH -- the beneficiaries of each other's findings.

Jan 1, 1999

By M. Stefanakis

Respect for the people is one of the main values of S&B. Such respect needs to be manifested by actions ensuring the bodily and spiritual integrity of personnel in pursuing their work. The ultimate target is to achieve zero accidents by developing the culture and infrastructure required to support it. Within this framework, the following proactive safety practices were introduced in 2004 and are implemented at S&B Greek sites: (a.) Management Safety Visits (MSVs) of shop floor operations to address safety attributes of work guidelines, (b.) Monitoring compliance with critical work guidelines, using a ?safety barometer? tool. The proactive nature of both above systems, facilitates communication with employees on safety behaviors and their adoption in our facilities at Milos and Fokis, has been successful. Above all, these practices corroborate the management?s concern for the people and its commitment to continuously improve the working environment.

Jan 1, 2007

By S. Stewart

The topic of sustainability in the mining and minerals industries focusing on economic development, ecological integrity and responsible stewardship of the environment together with community well being are vital issues for our industries at a crucial time in our history. Many of the priorities of the Greek Presidency of the European Community ? Sharing the Future in a Community of Values ? encourage our industry to continue to innovate and develop many of the environmental and social initiatives already underway. Sustainable development is here to stay and has been placed strategically at the heart of all European public policy. The future of the minerals industry here in Europe as well as elsewhere depends on how well professional mining people, both as individuals and through their associations and others, have to present their case for a sustainable mining and minerals industry to a critical world. And, Greece with its strong and expanding mining, minerals and metals base has more to win or lose from this endeavor than many others.

Jan 1, 2003

By J. Searls

The potash review arrived too late to appear in the June issue. Potash is a general term that includes several water soluble potassium salts: potassium chloride (muriate of potash), potassium sulfate (sulfate of potash), potassium magnesium sulfate (sulfate of potash-magnesia), potassium nitrate (niter) and sometimes potassium carbonate. Potassium carbonate was the original potash when it was leached from wood ashes and dried in large, cast iron pots to black-to-gray crystals (ash) to form "pot ash." "Pearlash" was potash roasted to white crystals. In modern terminology, the great preponderance of "potash" is the mined forms. It is estimated that 95% of the potash mined around the world is used as fertilizer. In 1840, Justus von Liebig demonstrated to the scientific community the importance of potassium to the growth of plants. But there was no low-priced source of potash available at that time. In the winter of 1851-1852, minable potash was discovered near Stassfurt,

Jan 1, 1991

By Milton E. Wadsworth

The evolution of engineering education and research has been profoundly influenced by computer technology and has concomitantly followed changes in this technology. Today, virtually all faculty have access to at least two hierarchies of computers: desk personal computers and at least one echelon higher (workstations or a variety of mid-sized computers). Most faculty have access to three or even four hierarchies: the two listed, plus super-mini and super computers. The ready availability of computers at a low cost has increased dedicated and site-specific computer technology. This has permitted universities to move into the field of macro-engineering, to address increasingly complex problems in resource recovery, manufacturing and many other areas, including important societal problems, like the environment. The creation of university research centers indicates the growing importance of macro-engineering involving large systems of interactive components. Funding agencies have increasingly favored such centers since they cross disciplines, generate inter-university consortia and foster university-industry programs.

Jan 1, 1992

By K. E. Lasaridi

Increasing soil organic matter was considered to be an important factor for the establishment of vegetative cover in abandoned quarries of perlite and bentonite in the island of Milos. For this reason, the feasibility of composting local organic wastes and by-products for use as a soil amendment was examined in this study. A mixture of organic wastes of vegetative origin and seaweed, in proportions that correspond to local material availability, was composted in laboratory scale reactors and the composting progress and compost quality were evaluated. Temperature, airflow and respiration rate were continuously monitored and various compost quality parameters, such as C/N ratio, nitrate nitrogen and seed germination were analysed. Addition of inorganic nitrogen was necessary for the biodegradation of the substrate, while the main problem for the compost utilisation was related to its high electrical conductivity, characteristic of seaweed containing mixtures, which further increased with nitrogen addition.

Jan 1, 2002