Search Documents

By S. S. Peng

Since the introduction of shield supports in 1975, safety and production in U.S. longwall faces have improved considerably. Many faces had a daily production of up to 8,000-10,000 tons and productivity reached 600 tons per man-shift. But a longwall face requires expensive equipment which slows down the growth rate of the percentage of longwall production. Among the equipment cost the shield support accounts for 50-60%, a very large proportion. Therefore, it will have a large impact on the growth of longwall mining in the U.S. to reduce the support cost (1).

Jan 1, 1988

By G. T. Austin

Every year the United States consumes millions of dollars worth of abrasive materials as blasting media. Entrained in either a gas or liquid stream or propelled by paddles or wheels, they are directed onto the surface of another material to modify that surface. The modifications to impacted surfaces include cleaning, cutting, deburring, etching, finishing, and peening. Blasting media can be either organic or mineral abrasive materials. Information and data presented are for only a portion of the mineral abrasives, they are; fused aluminum oxide, coal slag, copper slag, garnet, metallic shot and grit, nickel slag, olivine, silica sand, silicon carbide, and staurolite.

Jan 1, 1994

By W. M. Husslage, M. E. Kock, T. Bakker, R. H. Heerema

Permeability in the blast furnace shaft is adversely affected by low-temperature reduction degradation of sinters. The fundamental cause of this is the expansion of the iron oxide phase resulting from the reduction of hematite to magnetite. The present study shows that expansion behavior during the hematite/magnetite reduction .step and the resulting microstructure are strongly influenced by the reduction temperature (partial oxygen pressure), the reducing agent and the nature of the hematite. The reduction rate is of minor importance. A reduction mechanism is proposed that can explain the dilation behavior and the magnetite microstructure. The results provide better insight into the reduction degradation behavior.

Jan 1, 2000

By H. Polat, S. Chander

Relatively large amounts of hydrocarbons such as fuel oils are often needed in the flotation of low rank coals. The amount of oil can be decreased considerably by using surfactants as promoters. The reagents that are good candidates as surfactants to promote hydrophobicity can also act as emulsifying and wetting agents. Because the physical and chemical variables influence various subprocesses in different ways, their influence on the performance parameters is complex. The results of laboratory tests are presented to show that the dual role of reagents can be judiciously exploited to increase both the recovery and grade of the clean coal. The mode and order of reagent addition is critical in enhancing their efficacy as flotation promoters. The results demonstrate the benefits of proper conditioning of the pulp prior to flotation.

Jan 1, 1999

By R. M. Clowes

LITHOPROBE is a collaborative, multidisciplinary research project that is providing new insights into the tectonic evolution of the North American continent through its work within 10 study areas across Canada. For the mining industry, such results provide a well-constrained regional framework and better understanding of the tectonic processes that lead to the development of ore deposits. In mining camps, seismic-reflection methods have proven effective in imaging shallow to moderately dipping lithologic contacts as well as structural features and, in some cases, have been used for the direct detection of orebodies. Here, short case histories are provided for the Abitibi greenstone belt (VMS deposits) in Quebec and the Thompson nickel belt in Manitoba.

Jan 1, 2002

By Michael Francis, Chris Darton

More than 55 km of tunnels have been constructed by TBM in the last 12 years to refurbish and upgrade the high voltage cable network in London. These include a tunnel of 20km length using EPBM machines in both clay and granular soils. Route selection was made with reference to subsurface structures, existing ground conditions, using suitable shaft locations addressing environmental concerns. The complex interfaces to manage included obtaining of consents to the coordination of multiple suppliers. The paper describes how all these challenges have been met successfully and how technology has been employed to provide for safe construction and operation in the congested urban environment.

Jan 1, 2003

By Richard Minnitt, Philippe Renard, Christina Dohm, Winfred Assibey-Bonsu, Matthew Aboagye, Julien Straubhaar, Mahlomola I. Mabala

The application of multiple point statistics (MPS) in oil studies has gained traction over the years; however, the use of MPS in mineral resource estimation and classification is still limited. This is despite MPS’ ability to deal with complex and heterogeneous geology better than the commonly applied two-point based methods. The availability and choice of a representative training image (TI) are often cited as the main challenge holding back MPS’ application in mining geostatistical studies. On the other hand, the general approach used in mining whereby early focus is on higher grade areas and lower grades are planned to be mined later presents a massive opportunity for the development of representative TIs. Mined-out areas provide large amounts of historical data that can be used to develop training images or training datasets that can be used to estimate in mining extension areas (often lower in grade), provided low grade areas are underpinned by similar geology analogue. This approach will enable more robust estimates in mine/pit extension areas for both high- and low-grade extensions than with traditional two-point geostatistical methods.

Jun 25, 2023

By U. E. Paakkinen

Progress in computer control of flotation circuits has developed parallel with advances in reliability of on-stream X-ray analysis (Cooper, 1976). Attainment of acceptable results with X-ray fluorescence analysis over the past ten years has led to application of computer control in more than 30 concentrators. Gains in applying flotation control also have given incentive to improving measurement and control devices for other essential functions in control systems. At the same time, advancing technology has made available computer systems having characteristics practical and economical for the physical environments of concentrators and ore processing plants. Benefits from flotation control have centered on increased efficiency in mineral separations, derived by stabilizing circuit operation subject to changing ore characteristics. The gains have been most evident in processing complex ores for multiple concentrate products. In many cases, particularly when coupled with grinding control, the economic results from on-line control have been substantial compared to investments in monitoring and control equipment.

Jan 1, 1979

By R. L. Kloberdanz

Peruvian legislation requires the preparation of an Environmental Impact Study (EIS) for new and expanding mines/beneficiation facilities and the preparation and implementation of an Environmental Adjustment and Management Program (PAMA) to control and mitigate environmental impacts associated with existing mining/beneficiation activities. Shepherd Miller, Inc., developed guidance documents for preparing an EIS and PAMA for Peru's Ministry of Energy and Mines and presented workshops to Peru's mining industry on preparing an EIS and PAMA. This paper discusses the process and approach taken and the results.

Jan 1, 1998

By R. V. Ramani, J. Qin

During the mining process, the in-situ material is broken into different size ranges, from very large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable dust is associated with health and safety of the miners. The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined. The amount of respirable dust airborne is on the average only 0.016% of the respirable dust generated. On the average, 61% of the total airborne dust measured is in the respirable size range. The amount of respirable airborne is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (=0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of the airborne propensity of respirable dusts in mine atmospheres.

Jan 1, 1989

By G. P. Hand

The graphite industry as a whole has gone through many changes over the years. Most of the graphite used in major applications since the turn of the century were basic natural or electrode by-product synthetic materials, processed using simple crushing, screening, or grinding techniques. In the mid 1970's new thermal technology was developed which changed the face of the .graphite industry, and opened up a panacea of new products and capabilities. Materials produced through this new technology have helped revolutionize new products and processes in industries including automotive, batteries, fuel cells, electronics, iron, lubricants and steel. This paper outlines the continued improvements in those industries as well as the as well as the outlook for new technology in this rapidly changing area.

Jan 1, 1997

By Stephen J. Klein, Fernando Orduz, Randall J. Essex

INTRODUCTION The Keystone Tunnel project consists of widening an existing 7.3 m-wide (24 ft) highway tunnel to a width of 13.7 m (45 ft) to provide a three-lane, two-directional highway tunnel. The 13.7 m-wide tunnel was excavated in a staged drill-and-blast sequence through foliated schist, and was supported using pattern rock reinforcement and shotcrete. Notable project features are: the low vertical cover over the tunnel is less than the span of the opening; the project is the second instance where the Federal Highway Administration (FHWA) has accepted rock reinforcement as a permanent support element; and the project is the first instance where the FHWA is accepting shotcrete as the final interior surface of the tunnel. This paper covers the design and construction phases of the project. PROJECT DESCRIPTION The South Dakota Department of Transportation (SDDOT) retained Woodward-Clyde Consultants (WCC) to evaluate the feasibility, prepare construction plans and specifications, and provide construction management services for the widening of the Keystone Tunnel. The tunnel is located in the Black Hills National Forest area of South Dakota near the southwest corner of the state. The Keystone Tunnel is on U.S. Highway 16A, about 0.8 km (1/2 mile) north of Keystone which is approximately 32 km (20 miles) south of Rapid City (Figure 1). Highway 16A serves as an important transportation link between Rapid City and the Mount Rushmore National Monument which is located about 2 miles west of Keystone. The road through the tunnel consisted of two lanes about 7.3 m (24 ft) wide, and is being widened [ ]

Jan 1, 1989

By Byron Belew, Juris R. Harlamovs, D. B. Dreisinger, John L. Watson, G. A. Kordosky, Thomas O. O’Keefe

Unwanted impurities, present in raw materials, are often coextracted along with desired constituents during leaching. Due to its abundance and ease of extraction, the presence of ferric iron in leach solutions, solvent extraction circuits, and subsequently in electrowinning circuits, has always been a problem. In the case of zinc hydrometallurgical processing, iron is frequently an impurity in leach solutions. Purification of such solutions by solvent extraction, using di (2-ethylhexyl) phosphoric acid (D2EHPA) in a kerosene diluent, results in ferric ions being readily extracted along with zinc into the organic phase. Ferric iron has proven difficult to strip from the organic phase, but it is known that ferrous iron may be easily stripped from D2EHPA, and hence a process to effect reduction of iron present in the organic would have great potential. This research investigated a process to directly reduce ferric to ferrous iron in the organic phase, and to strip the ferrous iron using a dilute acid solution. The process utilized metallic zinc as the reductant and a low concentration sulfuric acid stripping solution. The results of the laboratory tests illustrated that iron could be readily removed from the organic phase by simultaneous direct reduction and acid stripping. The reductive stripping process was subsequently utilized in industry at the laboratory and pilot plant levels. The results of the industrial tests were encouraging and demonstrated the potential of this novel concept.

Jan 1, 1993

By Zhen-xing Diao, Feng Zhao, Ya-dong Xue

"Two important aspects of excavation performance of TBM are advance rate and cutter replacement/ring consumption, which is closed to the cost and construction duration of the project. To achieve this, a database of TBM parameters and the geological-geotechnical conditions during the excavation of Yinhanjiwei was compiled and analyzed. Relationships between different geological and TBM operational parameters were investigated. Results of analyzes show that there are qualitative correlation between Field Penetration Index (FPI) and rock geological parameters. And strong relationships between FPI and operational parameters are suggested. In this study, the cutter replacement and ring consumption were analyzed using statistical method for preliminary estimation in similar conditions. 1. ITRODUCTION Hard rock TBM is widely used in tunneling project nowadays because of its advantages to conventional drilling and blasting, especially in long tunnels. The biggest advantage is its high advance rate. However, rock conditions of tunnels are complicated. So TBM performance becomes a primary topic in tunneling engineering, which includes of rate of penetration, utilization, daily advancement, cutter consumption and so on. Many prediction models have been developed to estimate the TBM performance in the project planning phase. The most widely accepted and used models around the world are semi theoretical CSM model (Rostami and Ozdemir, 1993; Rostami, 1997) and the empirical NTNU model (Blindheim, 1979, Bruland, 1998).With increasing uses of TBMs in different ground conditions, an increasing number of researchers have developed new models in order to predict the performance of TBM more accurately in similar geological conditions.(Gong and Zhao, 2009; Hassanpour et al.,2009, 2010, 2011, 2014; Delisio et al., 2013; Delisio and Zhao, 2014)"

Jan 1, 2016

By Robert C. Cifelli

INTRODUCTION Background and Objectives Underground coal mining is a vital component of West Virginia's economy. However adverse environmental effects including ground subsidence and aquifer dewatering are often associated with such mining activities. Many families in northern West Virginia still rely on private water wells and springs for domestic water needs. In such areas where underground coal extraction and land subsidence have occurred, a disruption of the ground water flow system commonly exists with subsequent drainage of water to lower levels that may extent as deep as the mine workings; this causes loss of water supplies to landowners and represents a nuisance to mining companies 2 This report represents a summary of an M. S. thesis project in geology at West Virginia University by the senior author (3). The intent for this study was to document the effects of underground coal removal on ground water levels at selected mine sites in northern West Virginia, as observed from water wells, springs, and streams. This research should be useful to coal companies and regulatory agencies and aid in recommendations of future water well locations and specifications in areas of existing or proposed underground coal mines.

Jan 1, 1986

By James Watson Baxter

Fluxes are used to promote pyrometallurgical processes that rely on adhesion (soldering or brazing) or fusion (gas and arc welding) to join metallic surfaces. In the adhesive processes, the metal surfaces to be joined are not melted; the join is formed using a filler metal with lower melting point than the base metal. Fusion welding involves use of heat in excess of the melting point of the base metal. The fused joint may be achieved either by simply fusing together metal surfaces brought in contact with each other or by introducing additional molten metal of similar composition to form a fused joint. ADHESIVE PROCESSES--SOLDERING AND BRAZING In order for molten filler metal, solder or braze, to spread in a manner that creates a successful join; the work surfaces on the base metal must be thoroughly cleansed. Fluxes remove stubborn oxide films and other surface contaminants, promote wetting of the work surfaces, add fluidity to the solder or braze, and enhance workability and ease of spreading. Brazing processes involve higher temperatures than those reached in soldering. Brazing fluxes, which must remain active and effective at the higher temperatures, differ from those employed in soldering. Some common fluxes used in adhesive processes are rosin for soldering tin and electrical connections, hydrochloric acid for use in soldering galvanized iron and other zinc surfaces, and borax for brazing. Soldering and brazing are similar processes, the primary difference being the temperature at which the joining operation is carried out. Soldered joints, produced with low-melting-point fillers (solders) that melt and flow at temperature less that 450°C (Althouse et al., 1988) can sustain loads of 1 to 1.7 MPa for extended periods of time (Anon., 1966). Brazing involves the use of filler materials with melting points commonly above 500°C and generally provides stronger joints than those obtained with solder. Both processes require local application of heat to melt and spread the filler so that the molten filler can wet (adhere to) the base metals by alloying and diffusion. Soldering Soldering is a means of joining metals by adhesion using a metallic bonding alloy as the filler, commonly a mixture of lead and tin. However, the adhesion of solder depends more on its ability to be keyed into minute surface irregularities than on alloying. The most familiar application is to provide and secure electrical connections. Soft solders can range from 1 to 70% tin with the remainder mostly lead. However, for general-purpose, soft-solder work, the alloy is commonly 50% lead-50% tin. Higher lead contents provide a wider range in the melting temperature and, for this reason, a 60% lead-40% tin alloy, which yields a mushy mixture, is used for wiped joints in lead sheet and pipe work. Conversely, 40% lead-60% tin alloys are used in soldering tin and other low- melting-point materials for which a narrower range of melting temperature is required. There are numerous other solder compositions such as tin-silver, 95% tin-5% silver and antimony-tin, 95% tin and 5% antimony (Carlin, Jr., 1992). Heat needed to melt and spread the solders is commonly provided by electrically heated, copper-tipped soldering irons or by means of torches; the solder is applied by hand, usually face-fed by means of wire. For wiped joints in plumbing and lead-cable splicing, the solder is manipulated with cloth pads. The molten solder wets the joint surfaces and is drawn, by surface tension, into minute fissures and capillary openings. Other applications involve use of induction heaters and furnaces with pre-shaped solder appropriately placed prior to fluxing and heating. In some processes, the joints are immersed in molten solder. Constituents and Role of Soldering Fluxes: Soldering fluxes generally fall into one of three categories: highly corrosive fluxes, intermediate fluxes, and noncorrosive fluxes. These same categories are sometimes designated inorganic, organic and rosin-based respectively (Althouse et al., 1988). Common constituents of each group are discussed briefly below. Corrosive Fluxes (Inorganic). Work with aluminum, magnesium, stainless steel, high alloy steel, aluminum bronzes, and silicon bronzes is carried out at temperatures in the upper portion of the range for solder operations. Soldering these materials requires use of highly active, corrosive fluxes to remove and prevent the formation of the especially stubborn, hard, oxide films that form on these materials upon exposure to the atmosphere. The corrosive fluxes consist of inorganic acids and salts that are applied either as pastes or dry. They are active at elevated temperatures and, since they remain active after the soldering is completed, must be completely removed. The main constituent of most corrosive fluxes is zinc chloride with a melting temperature well above the solidus temperature of most commercial tin-lead solders. It is made by the action of hydrochloric acid on zinc. When zinc chloride is used alone, un- melted particles of this corrosive salt get caught up in the joint and weaken it. For this reason, other inorganic salts such as ammonium chloride (NH4Cl) or sodium chloride (NaCl) may be added to lower the melting temperature. A mixture of zinc chloride and ammonium chloride is very effective because the excellent oxide reducing properties of ammonium chloride and the protective action of the molten zinc chloride combine to produce a fluxing action superior to that achieved when either is used alone. In addition to zinc chloride, ammonium chloride, and sodium chloride; common con-

Jan 1, 1994

By John A. L. Campbell

Are safety concerns justified regarding the potential for a gas explosion due to recirculation when a scrubber is used on a continuous miner? The role of a respirable dust scrubber on a continuous miner section using blowing face ventilation is examined in this paper and the above question answered. Methane control using high efficiency scrubbers coupled with blowing face ventilation is promoted.

Jan 1, 1987

By C. J. Bise, D. A. Poukhovski

Hazard recognition and prevention of accidents are two components of the 30 CFR 48 training requirements, which are mandated for new miners and newly employed experienced miners. These components are also part of the annual refresher training course required of all miners. In these categories, instruction shall include the recognition and avoidance of hazards present in the mine and shall include a review of accidents and their causes. Unlike instruction preparation for fact-based material, program development for hazard recognition presents a particular challenge to safety-training specialists, because they are often limited in their ability to adequately gauge the level of awareness of the individual prior to training. Further, they must also assure that the training is relevant and presented in a thought-provoking manner. Computer-based instruction is particularly well suited for assisting trainers in developing hazard-recognition topics, because it can be used in pretraining and posttraining modes for assessment of training effectiveness, in addition to its use as a presentation tool. This article presents a recent approach, developed at The Pennsylvania State University, that applies the technology for the assessment and instruction of accident prevention through hazard recognition. The application is prepared for surface coal mines.

Jan 1, 1999

By James C. Gilliand

Leo-potpourri, was selected as the title to this paper for several reasons. First, it is a fascinating word--not looking like it sounds or sounding like it looks. It also allows for a great degree of flexibility in designing a presentation around it. Further, it has become popular to use this eco hyphen something pattern. We hear of eco-mania, eco-hysteria and the like. Lastly, in this era of intense environmental concern, two of the principle elements on which the integrity of our efforts must be equated are ecology and economics. Accordingly, the term "Eco-potpourris" allows me to roam at will through the great number of considerations that make up this environmental issue. Whereas only a few years ago the subject of environment and environmental control had low visibility with the public, today it competes as the focus of attention with the many other popular social issues of our time. The program content here at this meeting, for example, is liberally represented by papers dealing with one or more aspects of environmental concern. If one would look at the 1964 program, in contrast, I would expect that no more than possibly one or two papers covered this subject and even then that those papers dealt principally with the environmental aspect of occupational health. It is gratifying that the program at this meeting demonstrates a serious awareness to a broad spectrum of environmental concerns. It would be a mistake, of course, to believe that this clamor for a quality environment is a "flash in the pan" that will soon subside. The general public has been thoroughly aroused and even frightened into

Jan 1, 1972

By Gregory B. Baecher, Walter Steiner, Herbert H. Einstein

1. INTRODUCTION Empirical methods have always been important in tunneling in contrast to many other branches of engineering. Beginning in the late 19th century, when engineering entered the phase of formal modeling, this dichotomy could be seen to emerge even in the work of individuals. Culmann (1), Ritter (2) Kommerell (3) and others simultaneously were developing analytical approaches to bridge and building design and empirical approaches to tunnel design. The dichotomy remains. Empirical or simple analytical methods are used at most in the preliminary design of bridges and buildings, while they are used in all phases of tunnel design and construction. In fact, the past decade has seen a resurgence of interest in empirical methods, and with it discussion and controversy. This discussion has centered on the suitability of various methods. In some applications identical results are obtained with differing methods and in some cases radically different ones. On certain occasions the discussion has focused more on the methodological rather than empirical by taking issue with the appropriateness of particular parameters or the structure of some methods. This paper attempts to establish a basis for judging the suitability of empirical methods in tunnel design, and their applicability to particular cases. The paper makes no claim of exhaustiveness, and instead emphasizes basic requirements for application. Various methods are reviewed against this background. A detailed comparison of empirical methods and a description of their concept and background is now being prepared (4). Specifically the paper first defines empirical methods, and their purpose (Section 2), describes their structure (Section 3), and focuses on the basic requirements each must satisfy (Section 4). Then

Jan 1, 1979