Search Documents

By M. T. Simnad, G. Derge, I. George

Measurements of current efficiency on iron-silicate slags in iron crucibles showed that conduction is about 10 pct ionic in slags with less than 10 pct silica and about 90 pct ionic in slags with more than 34 pct silica, increasing linearly in the intermediate range. The balance of the conduction is electronic in character. Silicate ions are discharged at the anode with the evolution of gaseous oxygen. Transport experiments show that the ionic current is carried almost entirely by ferrous ions, which may be assigned a transport number of one. THERE has been increased evidence in recent years that the constitution of liquid-oxide systems (slags) is ionic.1-3 The principal studies designed to establish the structure of liquid slags have been by electrochemical methods', " and conductivity measurements1,6,7 which also have indicated the presence of semiconduction in several silicate systems1,4-0 and in pure iron oxide.' It is well known that many slag-forming metallic oxides have an ionic lattice type in the solid state, and their properties are determined to a large extent by the lattice defects and ion sizes. As Richardson8 as pointed out, the detailed models of liquid slags cannot be found on thermodynamic data only but "must rest on a proper foundation of compatible structural and thermodynamic knowledge, combined by statistical mechanics." A careful thermodynamic study of the iron-silicate slags has been carried out by Schuhmann with Ensio9 and with Michal.10 They obtained experimental data relating equilibrium CO2: CO ratios to slag composition and made thermodynamic calculations of the activities of FeO and SiO, and of the partial molal heats of solution of FeO and SiO2 in the slags. It was found that the activity-composition relationships deviate considerably from those to be expected from an ideal binary solution of FeO and SiO2. However, the partial molal heat of solution of FeO into the slags was estimated to be zero. Their experimental results were correlated with the constitution diagram for FeO-SiO2 of Bowen and Schairer,11 with the results of Darken and Gurry" on the Fe-O system, and with the work of Darken"' on the Fe-Si-O system. All these studies were found to be consistent with one another. The variation of the mechanism of conduction with composition in the liquid iron-oxide-silica system in the range from pure iron oxide to silica saturation (42 pct SiO2) in iron crucibles was reported in a preliminary note." The current efficiency, or conformance to Faraday's law, showed some ionic conductance at all compositions, the proportion increasing with the concentration of silica. The current-efficiency experiments since have been extended. Furthermore, transport-number measurements have been completed in silica-saturated iron silicates to determine the nature of the conducting ions. Experimental Current Efficiency in Liquid Iron Oxide and Iron Silicates using Iron Anodes: This study was carried out by passing direct current through slags in the range from pure iron oxide to iron oxide saturated with silica (42 pct silica), using pure iron rods as anodes and the iron container as the cathode. A copper coulometer was included in the circuit to indicate the quantity of current passed during electrolysis. Assuming that the cation involved is Fe-+, the theoretical quantity of iron lost from the anode according to Faraday's law may be calculated and when compared with the actual loss observed, gives an indication of the extent to which Faraday's law has been obeyed. It also gives an indication of the presence and extent of ionic conduction in the melt. Preparation of the Slags: About 100 g of chemically pure Fe,O, powder is placed in an iron pot which is heated by induction until the contents liquefy. In this way, FeO is produced according to the reaction Fe2O3 + Fe = 3 FeO. More Fe2O3 or SiO, powder is added and, when a sufficient quantity of molten slag is obtained, the induction unit is turned off, the pot withdrawn, and the molten slag poured on to an iron plate. Homogenization and Electrolysis of the Slag: Apparatus—After considerable development, the setup illustrated in Fig. 1 proved to be quite satisfactory. A is an Armco iron cylinder, 1 in. ID and 1/8 in. wall, consisting of three sections placed one on top of the other. The bottom section is a pot about 5 in. long with a small hole drilled in its bottom to allow withdrawal of gases during evacuation of the apparatus. The middle section is 6 in. long and consists of a pot which serves as the slag container, while the top section is a hollow-cylinder continuation of the slag-container pot. The height of this latter section is about 5 in., giving an overall length of approximately 16 in. The iron cylinder is constructed in this way for ease of fabrication, the individual sections becoming welded together after the

Jan 1, 1955

By G. W. Jones

An important activity of the Bureau of Mines is the promotion of safety in mining and industry. As a part of this program, the Bureau determines the explosion hazards of combustible gases, vapors, and solids and investigates means of controlling and preventing explosions. The limits of inflammability (explosive limits) of combustibles are not only of theoretical but also of practical importance, because many industries at one time or another contend with explosive mixtures of combustible gases or vapors in their manufacturing processes. At present many new organic compounds are being manufactured, transported, and used in huge quantities which a few years ago were only laboratory curiosities.

Jan 1, 1941

By Eiichi Kuzuno, Atsushi Shibayama, Toyohisa Fujita, Kazuo Koike, Toshio Miyazaki, Hitoshi Masuda

"A solid sulfur is more useful to recover and store than a sulfuric acid as a by-product in the zinc hydrometallurgy. In this experiment a zin concentrate (sphalerite) was leached with ferric sulfate at about 373 K for 3 to 6 hours. Zinc was leached more than 95%. After a solid-liquid separation, the leached residue contained solid sulfur was obtained. The particles in the residue were dispersed by lignin and the solid sulfur of approximately 85% was recovered as float product by a flotation with frother in the pH 4. The dried float product was heated at 413K for 2 hours. The pure solid sulfur was recovered. On the other hand in the leached liquid a zinc oxide was ·added and ferrous .iron was oxidized to ferric iron by blowing oxygen. This ferric iron was returned to the zinc leached process after solid-liquid separation.IntroductionZinc concentrate is usually roasted as pretreatment in zinc hydrometallurgy and the produced S02 is changed to sulfuric acid. However, recently in Japan the utilization of sulfuric acid has been limited and it is more costly to store. Instead of producing sulfutic acid the solid sulfur recovery has been examined by direct leaching of zinc_ concentrate in this experiment.In the direct leaching, several kinds of effects have been studied for leaching of sphalerite in ferric sulfate solution. The addition of lignine siilfonate1 • 2) and fine· grinding3) increases the · speed arid leaching fraction of sphalerite. The leaching ratio depends on impurities in sphalerite ores4 • 5). Here, the zinc concentrate is leached ferric sulfate solution under atmospheric pressure at 373K. The solid sulfur in leached residue is separated as float products from other solids by sink-float separation and flotation. The sulfur in float products is purified by evaporation at 413K and recovered."

Jan 1, 2000

By August E. Vandale

I speak to you today on the subject assigned to me, "Subsidence - a Real or Imaginary Problem", as a representative of Consolidation Coal Company (a wholly owned subsidiary of Continental Oil Company). The information I relate to you is our experience in the Pittsburgh Coal Company Division of Consol and covers the Pennsylvania properties and mines with particular emphasis on the mines in the south- western portion of the State or in the immediate vicinity of Pittsburgh, Pa. Mining of Freeport and Pittsburgh seams of coal in the Pittsburgh vicinity dates back over one hundred years. Consol, or its predecessor, Pittsburgh Coal Company, has been actively engaged in mining in the area since Pittsburgh Coal Company was organized in 1900. Pittsburgh, Pennsylvania came into prominence as the Steel City largely because of the vast reserves of high grade metallurgical coal readily available in the immediate vicinity and also because of its favorable river transportation. Early in the 1900's we operated over 100 small coal mines, with operations located in the Counties of Allegheny, Fayette, Washington, Westmoreland. We have also operated mines in Somerset and Greene Counties. Titles in Pennsylvania can be in three estates: (1) title in fee, (2) title to the mineral, (3) mining rights permitting the removal and extraction of the mineral with or without waiver of surface damage. Consol has over the years acquired good legal title to the coal lands purchased from individual farm owners, with good broad mining rights, and in 98% or more of its title has a complete waiver of surface damage or the right to subside the surface land. In the early days of our Company, individual coal farms were purchased from land owners. Many of these titles severed the coal estate from the in fee title and good mining rights with waiver of surface were conveyed in the original severance deed. Thus, minable coal reserves were put together by the purchase of the coal under many individual farms in an area. In the early years, the mines practiced hand dug mining - later going to mechanical cutting with hand loading of the coal. Systems used were entry driving with room and rib panels. We have practiced full recovery mining as far as practical during the years of hand loading, as well as in the later years when the mines were mechanized. Mining system layouts, methods and procedures have changed from time to time to keep pace with improved mining machinery and new inovations, such as roof bolting and rubber tired haulage.

Jan 1, 1967

By A. Warczok, C. M. Diaz, A. Bergman, T. Utigard, M. Barati

The world wide consumption of energy is steadily increasing and by 2030 it is forecasted to grow by another 50%, leading to mounting political and economic pressures. For any pyrometallurgical operation, it is therefore paramount to investigate and implement methods to decrease the use of energy. In the pyrometallurgical processing of steel, copper, nickel and other high temperature metals, a large amount of energy is lost in hot off-gases, molten slags, mattes and molten metals. Most of this energy is generally lost during the cooling and solidification steps with very little focus on energy recovery or reuse. In this paper we will quantify how much energy is contained in the various slag streams, then review previous attempts and methods employed to recover some of this energy, and finally evaluate some novel technologies that could potentially be employed.

Jan 1, 2011

By L. E. Djingheuzian

Introduction Cylindrical grinding mills have been used for a long time, but during many years of testing no methods were established that gave consistent results. The work by both scientific investigators and operators led very often to contradictory conclusions, and each millman was very much 'on his own' when trying to find the limits for working of his ball-mills. Fred C. Bond, in the introduction to his paper on Wear and Size Distribution of Grinding Balls, freely states that the mathematical immaturity of the grinding process "is the cause of many inefficient designs and installations as well as of much poorly oriented experimental work", and evidently he sees the solution of all our grinding problems in the discovery of the fundamental laws "which can change the empirical art into a mathematically exact science". While the writer is in complete agreement with Mr. Bond that grinding is governed by fundamental laws which can be expressed by mathematical formulae, there are so many variables in grinding, all interwoven with each other and mutually influencing each other, that the coalescing and merging of all these variables into a harmonious mathematical whole appears to be a homeric job. However, a light appeared on the horizon when it was proposed that power be used as an index of the grinding operation. It is pertinent to quote Gow, Guggenheim, Campbell, and Coghill from their paper on Ball Milling, in which they say: "Much of the past literature devoted to the subject has been concerned with the Kick-Rittinger dispute over evaluating grinding, or with dissertations on ball paths and the closely allied impact versus attrition hypotheses or with the exclusive consideration of certain specific variables, such as mill speed or circulating load, irrespectve of the other factors in operation. Such subjects may be dismissed with but little discussion in what may be called, by comparison a new philosophy in the stud of ball milling. Briefly this 'new philosophy' consists ' of using power as an index of the mill operation, and investigating grinding from the standpoint of set and induced variables with emphasis on the latter". But it is safe to assume that it was the work by E.W. Davis, H. E. T. Haultain, F. C. Dyer, A: M. Gaudin, J. Gross, S. R. Zimmerley, and others, that cleared the path for the authors of Ball Milling and induced them and A. W. Fahrenwald to look farther afield and thus to establish a far-reaching relationship between the power and capacity and the diameter of the ball-mills.

Jan 1, 1949

By Wang Haibei

China is the important country in terms of Ga, Ge reserves and products. These elements usually associate with lead and zinc ores such as in Fankou, Dachang and Lanping mines. Until now these metals could not be extracted from zinc residues effectively. The main reason is that it is difficult to separate zinc and iron. BGRIMM has carried out considerable research on this subject and some hydrometallurgical processes were developed. Zinc residues were pressure leached with a reducing agent such as zinc concentrates or SO2 at 110~130C. The final concentrate of H2SO4 was 30~50g/L. The metals such as Zn, Fe, Ga and Ge were dissolved into solution. In the leaching residue Pb and Ag could reach 20% and 2000g/t. The feed of solvent extraction was prepared from the leaching solution by pre-neutralization ? precipitation of Ga, Ge and acid dissolving. Then Ga and Ge were extracted by solvent extraction through P204 and G315 produced by BGRIMM. After stripping, metallic Ga was produced by electrowinning. GeO2 was produced by precipitation. The iron in raffinate was removed by the hematite process. The solution after removal of iron came back at the zinc neutral leaching stage. In 2003-2004, pilot tests were finished in BGRIMM in cooperation with Fankou Lead and Zinc Mine Ltd. And the extraction rate of Ga and Ge in the leaching stage was 94% and 83% respectively. The total recovery rate was 90% and 80%. It is estimated that the technology has a wide commercial use in the coming five years.

Jan 1, 2006

By D. Loring, J. Almgren

Climax Molybdenum Company’s Henderson Mine is a large panel caving molybdenum mine located about 43 miles west of Denver, Colorado. Three Joy M120-72-880 fans are installed in parallel on the No. 1 exhaust shaft. Throughout the mine’s history, ventilation changes such as the completion of the No. 5 exhaust shaft have decreased the utilization of these fans. To optimize fan performance they have been run with the full complement of 16 blades, down to as few as four blades. Since the completion of ventilation upgrades associated with the Henderson 2000 project, one surface fan has been operated under normal conditions with 10 or 12 blades. With the completion of a new network model of the Henderson ventilation system, a tool was built to develop fan curves for possible future fan configurations and predict future fan performance. This paper describes the tool and its use at Henderson.

Jan 1, 2007

By Andy Fortin, Jeet Basi, Simon Hille

Goldcorp’s Eleonore mine is situated in Ell Lake area in the northeastern part of the Opinaca reservoir in the James Bay region of Quebec. The design of the 7000 t/d process plant includes crushing, grinding, bulk sulphide flotation, separate concentrate and tails leaching and detoxification circuits and residue handling. Detoxified flotation tails are thickened and filtered. A portion of the filtered tails are blended with the thickened detoxified sulphide concentration for paste backfill. The remaining filtered tails are trucked to the waste management facility. This presentation will describe the challenges faced with the commissioning and subsequent ramp-up of the flotation tails filter plant and the successes achieved by the multi-discipline team at Eleonore.

Jan 1, 2016

By Arthur F. Taggart

The quality of aggregate materials is. of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 1, 1950

By I. K. Choi

In a recent paper by Smith and Wen(1) the adsorption of sodium dodecylsulfate and trimethyldodecylammonium chloride on kaolinite was studied. As would be expected considering the general negative character of kaolinite, except perhaps at quite' acid pH values (2,3,4), it was found that trimethyldodecylammonium chloride adsorbed strongly on kaolinite at basic pH values. Furthermore, it was found that sodium dodecylsulfate adsorbed strongly on kaolinite at acid pH values, particularly at initial 1H values below pH 3 (final pH values near pH 4). It is interesting to note that adsorption of the anionic surfactant was strong under conditions where the kaolinite was apparently slightly negatively charged (2). The present paper reports on an extension of the work by Smith and Wen. In this paper the effects of the presence of dodecyl alcohol and sodium hexametaphosphate on adsorption of sodium dodecylsulfate and trimethyldodecylammonium chloride on kaolinite are considered.

Jan 1, 1967

By J. Sikamo, A. Mwanza, C. Mweemba

"The Zambian copper mining industry as we know it today had its genesis in the 1920s. Consistent private sector-driven investment in the industry over a period of over 50 years in exploration, mine development and operation, development of minerals processing facilities, building of infrastructure for pyrometallurgical and hydrometallurgical processing, with attendant support facilities, including building of whole new towns, resulted in copper production rising to a peak of 769 000 t in 1969, providingover 62 000 direct jobs. The industry was nationalized in 1973 and remained in government hands for just over 24 years. During this period, the industry experienced a serious decline in production levels, reaching the lowest level in the year 2000 when production was 250 000 t. An average of just under 2000 jobs were lost every year in the 24-year period, reaching just over 22 000 direct jobs in 2000.Following the return of Zambian politics to pluralism and liberalized economic policies, the government decided to privatize the mining industry. The process started in 1996 and by the year 2000 all the mining assets had been privatized. The new investors embarked on serious investment to upgrade the assets and to develop greenfield mining projects. Fourteen years later and after more than US$12 billion investment, production levels increased year-on-year to a peak of 763 000 t in 2013 with direct jobs reaching 90 000.This paper discusses the impact of the mining industry in Zambia on the economy in areas such as employment, support for other industries, direct contribution to the national gross domestic product (GDP), foreign exchange earnings, and social amenities. The paper also focuses on the performance of the mines during these periods vis-à-vis mineral availability, mineral grades and complexity, new technologies, and human capital. This is looked at particularly in the light of current challenges the industry is facing. Suggestions are proposed on how the industry can be nurtured to continue being a major driver for the Zambian economy and a major player in the international copper mining business."

Jan 1, 2016

By J. Priede, G. Gerbeth

"Two different instability mechanisms of electromagnetically levitated bodies are analyzed. The first is due to the virtual coupling between the electric current passing through the magnetic system and the variation of position of the body. This mechanism can result in unstable mass center oscillations of a levitated solid body. Another type of instabilities may occur because of the coupling between the motion and the electric currents induced in the body. This effect can cause a spontaneous rotation of the body setting in as the frequency of the alternating magnetic field exceeds certain critical threshold depending on the configuration of the field. This instability can be suppressed by an axial steady magnetic field of strength comparable to that of the levitating field. 1 IntroductionAn alternating magnetic field interacting with eddy currents induced in a conducting body causes repulsion between the body and the coil generating the field. Besides, the eddy currents provide a contactless heating of the body. In such a way metallic samples can be levitated and melted without a contacting crucible. This technique allows to avoid contamination of the melt with container material and so to achieve a considerable super-cooling of the melt before it solidifies. Nowadays electromagnetic levitation is widely used in material research for measuring of the thermophysical properties of molten metals (2) .It has been observed since early fifties when the first experiments on the electromagnetic levitation were done that under certain circumstances solid levitated samples start to rotate or oscillate [l]. Surface oscillations can appear in addition when the sample is melted. Such phenomena are undesirable because they often result in failure of the levitation. Recently we showed that rotational as well as oscillatory instabilities can have electrodynamic origin related to additional eddy currents induced by motion of the body in an alternating magnetic field [3] , [4].In the first part of the present paper we analyze another possible cause of oscillatory instability due to the coupling between the electric current passing trough the magnetic system with variation of the position of the levitated body. The second part of the paper deals with the origin and suppression of rotational instability in a uniform alternating magnetic field."

Jan 1, 1999

By M. Okido, H. Yamamoto, T. Sakamoto, R. Ichino, K. Kuroda

"Hydrogen absorption alloy films have been produced by molten salt electrolysis. Lanthanum-Nickel alloy film can be formed on a nickel substrate in KCl-NaCl-LaCb molten salts by electrolysis diffusion process. LaNi5 alloy was formed by mutual diffusion between La ·and Ni after La deposition on Ni substrate. Though several kinds of La-Ni compound existed in deposits, the alloy compounds on Ni substrate changed by electrolysis condition. According to the open-circuit potential measurement in molten salts after La electrodeposition, the formed compounds had a relation to the potential. In the case of the substrate electroplated a cobalt thin film on nickel, LaNi4_5Co0.5 was formed by the electrolysis in the molten salts with lanthanum ions. This ternary alloy film showed better hydrogen absorption behavior in cyclic charge/discharge test in alkaline solution.IntroductionHydrogen storage alloys have attracted attention as the active materials for batteries with the charge/discharge property at ambient temperature. The alloy of nickel and misch metal, mainly consisting of La and Ce, has been commercially 'used as a metal hydride with rechargeable property. In recent years, researches have been developed many kind of new alloys with better hydrogen absorption properties. The hydrogen absorbing alloy ingots are commonly produced by melting method of both metals in furnace, otherwise, prepared by mechanical grinding and metallurgical sintering technique with metal powders. The film is also made by vapor-phase techniques such as sputtering method, ion plating method, etc. ·We have proposed a new method to produce hydrogen absorbing alloy films by molten salts electrolysis technique [1-3]. The hydrogen absorbing film, LaNi5, Mg2Ni and CaNi5, were obtained in this process through controlling the electrolytic condition. The active metals, La, Mg and Ca, are electrodeposited on Ni substrate, diffuse into the substrate and form various kinds of intermetallic compounds. This technique provides a direct process using metal chlorides as resources to produce functional films without using active metals such as La, Ca and Mg."

Jan 1, 2000

By H. K. Lin

Pyrite oxidation in chloride solutions was investigated with cyclic voltammetry, ac impedance and potential step techniques. The pyrite oxidation in quiescent electrolytes is irreversible and controlled by diffusion. Depression of the semi-circle in the complex plane plot has been explained mathematically based on the concept of the equivalent circuit. When the semi-circle is depressed, the mathematical formula indicates that the reaction resistance should be obtained from the intersection of the semi-circle with Z-axis instead of the semi- circle diameter. The peak charging current densities at 1.10 and 0.90 V vs. SHE obtained from the equivalent circuit coupled with the ac impedance measurements match the peak current densities obtained with the potential step measurements.

Jan 1, 1997

By A. R. Chambers

Malagash received its name from the Indians many years ago on acco.unt of its turbid (milky) waters, although,' the red men did not appreciate the significance of this turbidity, and were, of course, entirely ignorant of the crystal beds of pure salt that lay beneath their feet. The salt lake of the Mississippian, or Lower Carboniferous period, in which these beds occur, was apparently a large one, for there is evidence of its existence at intervals all the way from Sydney, Cape Breton, to St. John, New Brunswick, 300 miles as the crow flies, and there is no knowing what its other dimensions may have been, as much of this horizon is now buried on the one side beneath the waters of the Gulf of St. Lawrence, and on the other underneath the Atlantic ocean. About midway of the area and underlying the counties of Colchester and Cumberland, there occurs a synclinal basin of which the Malagash salt outcrop forms only a small portion of its northern limit. This basin has been described very fully by A. C. Hayes. (1) The operations carried on at Malagash since Hayes wrote his report have brought to light very little in the way of new geological data, except to confirm his pre-dictions as to the probable faulting of the salt strata, and the effect which these faults would have on mining operations.

Jan 1, 1924

By M. Kumral, E. Dilhuydy, B. Ozdemir

"In-pit crushing and conveyor (IPCC) systems have become increasingly popular in the mining industry as an alternative to truck-and-shovel systems. Deciding whether to haul waste rock by truck or IPCC represents an important gap to be investigated in semi-mobile IPCC systems. A cost analysis is presented to evaluate the feasibility of crushing and conveying waste material in IPCC systems, along with sensitivity and risk assessments through Monte Carlo simulation. Although the capital expenditure is higher, results showed waste crushing will be feasible in deep pits and over long mine life and haul distances.RÉSUMÉ La popularité des systèmes de concassage et de transport dans la fosse minière (IPCC, de l’anglais In-pit crushing and conveyor) n’a cessé de croître dans l’industrie minière ; ils constituent en effet une option intéressante de remplacement des systèmes par camions et pelles mécaniques. Le choix entre le transport des stériles par camions ou par IPCC est encore difficile à faire et devra faire l’objet d’une étude approfondie au niveau des systèmes d’IPCC semi-mobiles. Une analyse des coûts est présentée pour évaluer la faisabilité du concassage et du transport des stériles par les systèmes d’IPCC, de même que des évaluations de la sensibilité et des risques par le biais de la simulation de Monte Carlo. Si les dépenses en immobilisations s’avèrent être plus élevées, les résultats ont cependant montré que le concassage des stériles sera envisageable dans des fosses profondes ainsi que sur une longue durée de vie et de longues distances de transport. INTRODUCTIONThe mining industry is currently facing many challenges such as low commodity prices, increasing environmental concerns and regulations, lower grades, deeper mines, and greater waste-rock quantities. As a result, the profitability of mining operations has decreased, with many mines stopping or suspending operations, and many new projects being postponed. Mining companies have therefore focused on improvements and innovations to increase the cost effectiveness of operations, for example, increasing production capacity to take advantage of the economies of scale (Crowson, 2003) and decreasing the unit operation cost. Changes in production capacity force mining companies to evaluate alternative material handling systems.During the past few decades and within material handling systems, significant improvements have been made to truck performance and capacity. Consequently, operating expenditures (OPEX) associated with fuel and maintenance have risen swiftly. In a mining operation, truck hauling systems now represent 40–50% of the capital cost and approximately 45% of the OPEX (Tutton & Streck, 2009). Additionally, material transportation costs are expected to increase due to longer haul distances arising from deeper and larger mines (Fleet et al., 2015). Finally, large fluctuations in fuel prices result in high risks associated with truck OPEX. According to the United States Energy Information Administration (2015), the cost of crude oil—the largest component of the retail price of diesel fuel—increased from US$24.31/barrel in 1986 to US$46.92/barrel in 2016, peaking at US$151.72/barrel in 2008 (Macrotrends, 2016)."

Jan 1, 2017

By A Clark

When production targets are not being reached it is essential to determine what the operating problems are so that remedial action can be taken. It is also imperative that all persons who are part of the production stream within a mining operation know and understand what the operating difficulties and delays are so that corrective action is effective. This includes the supervisors, superintendents, planning team members and managers. A new approach recently adopted at Hilton Mine to help identify these operating difficulties has been to use short-term schedules and reports known as the Daily Shift Schedule Controls (DSSC), and the Daily Weekly Operating Reports (DWOR) respectively. These control elements have enabled management and supervisory staff to accurately identify labour inefficiencies and ultimately determine capital resources.

Jan 1, 1998

By David Hartley

United States Steel Corporation Minntac Mine is located at Mt. Iron, Minnesota, on the Mesabi Iron Range. The taconite pit is two miles long by a mile wide, with a maximum depth of 170 feet. This paper will deal with the radio remote control of locomotives engaged in the railroad haulage of crude ore and waste rock at this property.

Jan 1, 1970

By Vitor Manoel de Araújo Silva

Os aços inoxidáveis austeníticos são materiais utilizadas nos ramos petroquímico, nuclear e aeroespacial cujas demandas se resumem essencialmente à: boa resistência mecânica, excelente soldabilidade e elevada resistência à corrosão. Apesar destes metais atenderem a estes requisitos, não raro são submetidos a etapas de conformação para elaboração de peças, o que pode modificar as suas propriedades originais. Basicamente, a causa desta mudança são alterações metalúrgicas induzidas por deformação, como a transformação da austenita (paramagnética) em martensita-a’ (ferromagnética). Tendo em vista que tais mudanças são acompanhadas de variações nas propriedades elétricas/ magnéticas destes aços, uma maneira de monitorá-los de maneira não destrutiva é através da técnica de correntes parasitas. Para este estudo, diversas amostras de aço inoxidável AISI 321 foram solubilizadas e deformadas por laminação a fim de produzirem diferentes frações volumétricas de martensita. Em seguida, submetidas à microscopia ótica, magnetômetro de amostra vibrante e correntes parasitas. De acordo com os resultados, percebe-se que toda a transformação martensítica se passa no intervalo entre 0,10 e 0,55 de deformação verdadeira. Além disso, com os dados de magnetização de saturação, foi possível estabelecer uma curva de calibração de comportamento exponencial, permitindo a quantificação da martensita de maneira não destrutiva.

Oct 30, 2017