Search Documents

By H. C. Fiedler

It was recently shown with 3.3 pct Si-Fe containing 0.026 pct S and 0.06 pct Mn that the extent of secondary recrystallization to a cube-on-edge texture is determined by the cooling rate from the solution temperature of the manganese sulfide inclusions.1 With a rapid cooling rate, many small inclusions rather than a few large ones are formed, which leads to increased restraint to normal grain growth and more complete secondary recrystalliza-tion. Strip samples 12 mils thick, rolled from 1-in.-thick slabs that were cooled at 130°C per min

Jan 1, 1964

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942

By N. Van Wingen

EFFective sand permeabilities can be ascertained from core analysis if the laboratory data are compensated to allow for the presence of connate or residual water. Such adjustments can be made by applying empirically derived correction factors. Effective sand permeabilities can be estimated also from analytical studies of field depth-pressure measurements. In one method the time rate of pressure build-up after a well is shut in from steady-state flow is required, and in the other the direct measurement of a steady-state rate of flow and the corresponding equilibrium pressure. The results of the investigation discussed in this paper demonstrate that these methods for determining mean effective sand permeabilities can be correlated. Introduction In recent years many investigators have demonstrated the practical value of an accurate knowledge of the physical and dynamical characteristics of reservoir sands containing oil and gas. Of these factors, which serve to completely define a porous medium as a container or carrier of fluids, the dynamical characteristics are of particular interest to the production engineer because they afford a direct measure of the rate at which the oil or gas content of a reservoir will become available. The constant that defines dynamically the porous medium as the carrier of a homogeneous fluid in viscous motion is the "permeability." Coke-analysis Method The generally accepted practice in com-piling permeability data has been to analyze in the laboratory core samples taken in the course of drilling through the productive horizon, and to obtain the mean measure of the productive ability or permeability for the interval open to production by graphical integration of the permeability profile. An average permeability ascertained in this manner, however, is useful to the production engineer only for comparisons of wells drilled in the same horizon, as permeabilities determined in the laboratory are measures of only the ability of a porous medium to transmit a single fluid. As a result of many investigations, it has been shown, however, that under actual reservoir conditions water is coexistent with the petroleum and that its presence greatly reduces the permeability of the sand to oil. Empirical relationships showing the effect of the presence of any immiscible fluid A (such as water) in a porous medium on the permeability of the medium to a fluid B (such as oil) have been established separately by Hassler,1 Dunlap,2 and the writer (Fig. I),3 so that the average specific or dry-core permeability as determined in the laboratory can be corrected to give the true measure of the ability of the horizon penetrated to transmit oil, provided the percentage of pore space occupied by connate water is known accurately.

Jan 1, 1942

By J. L. Kenty, J. P. Hirth

The concept of a critical super saturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, is discussed with reference to vapor-solid nucleation. The necessary and sufficient conditions deduced for observations of this type of behavior are: 1) the nucleation rate must exhibit a sharp dependence on super saturation, 2) the growth rate must be sufficiently large that nuclei become observable in the time period of the experiment, and 3) the number of highly preferred nucleation sites must be small. Experiments reveal that the nucleation of silver on sodium chloride is visually detectable at all experimentally accessible super saturations and does not exhibit critical nucleation behavior. Failure to observe a critical super saturation is attributed to the insensitivity of nucleation rate to supersaturation as a consequence of the particular values of the contact angle and the surface free energy for this system. THE concept of a critical supersaturation, below which the nucleation rate is essentially zero and above which it is essentially infinite, arises naturally in homogeneous nucleation theory. Experimentally this type of behavior has been found by Volmer1 and others for water and other low surface tension liquids, as reviewed by several authors.2'3 The same type of behavior has been predicted and observed for heterogeneous nucleation of solids by Yang et al.4 and others,596 as also recently reviewed.2,7,8 In the work reported here on the heterogeneous nucleation of silver on NaC1, however, no critical super-saturation was found. Similar observations have been made recently for other systems.9-11 These results led to a reexamination of nucleation theory which revealed that there are conditions for which critical behavior is not predicted, either for homogeneous or heterogeneous nucleation. Although heterogeneous nucleation is of primary importance in this paper, some insight into critical behavior for such a case can be gained by considering homogeneous nucleation. Accordingly both types of nucleation theory are reviewed briefly. The requisite conditions for critical supersaturation behavior are then considered. The experimental results for the nucleation of silver on NaCl are presented and interpreted in terms of the theoretical presentation. REVIEW OF NUCLEATION THEORY There are essentially two approaches to nucleation theory, the so-called classical theory involving the concepts of bulk thermodynamics, and the statistical mechanical theory in which nuclei are regarded as macromolecules. The classical theory is based on the work of Volmer and Weber12,13 and Becker and. Doring14 and has been extended by Pound et al.15 The crucial assumption in the classical theory is that the small clusters or nuclei can be characterized by the same thermodynamic properties as those of the stable bulk phase. Thus, the nuclei are assumed to have a surface free energy, y, and a volume free energy of formation (relative to the vapor phase), ,, identical to that of the bulk. For deposition under low super-saturation conditions, the nuclei are large and this assumption is satisfactory. However, in many cases of interest, the nuclei contain only a few atoms and this assumption is highly questionable. The statistical mechanical models originated, for the specific case of a dimer as the critical nucleus, with the work of Frenkel16 and were extended later to larger sizes by Walton,17,18 Hirth19 and, more recently, Ht Zinsmeister. These models describe the nucleus in terms of a partition function, the estimation of which is tractable for clusters of 2 to 10 atoms, but extremely difficult for clusters larger than 10 atoms. Although the classical and statistical mechanical models are expected to apply for the limiting cases of large and small nuclei, both are uncertain for intermediate sizes. In this paper we shall treat only the classical model, recognizing that it is exact only for large nucleus sizes and regarding it as a phenom-enological description for small nucleus sizes. When analyses of experimental data using bulk properties show the nucleus size to be small, the resulting parameters should be regarded as largely empirical parameters describing the relative nucleation potency of the system. Considerable justification for the continued use of classical theory is provided by its general success in predicting nucleation behavior as a function of supersaturation and temperature. We emphasize that the qualitative features of the statistical mechanical models, particularly the critical super-saturation behavior that is central to the present work, are the same as those of the classical model. Of course, potential energy terms and surface partition functions replace the volume and surface energy terms of the latter model. The most recent versions of classical nucleation theory have been extensively reviewed.2,3,7 so that only the results are presented here. For homogeneous nucleation of a condensed phase from the vapor phase, the volume free energy change is ?Gv=vrT = =^ln£ [1] where v is the molecular volume of the condensing species. The supersaturation ratio,

Jan 1, 1970

By David Mitchell

THE production of fluorspar is one of the smaller nonmetallic indus-tries in the United, States with a capital investment-about $10,000,000. Shipments from United States mines1 in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 Fluorspar is marketed according to the following relative quantities and specifications: Consump- Specifications, Per Cent Use Form tion in 1936, Per Cent CaF2 SiO2 Fe2O3 Metallurgical Gravel 79 +85 -5 or lump Ceramic.. Ground 10 +95 -3 -0.1 Acid Ground 11 +98 -1 The concentration of the coarser sizes presents relatively little diffi-culty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1938

By David Mitchell

THE production of fluorspar is one of the smaller nonmetallic indus-tries in the United States with a capital investment-about $10,000,000. Shipments from United States mines' in 1936 totaled 176,231 short tons valued at $3,111,268, an average price of $17.65 per ton. The United States produces about 40 per cent of the world's fluorspar, of which about 90 per cent comes from the Illinois and Kentucky deposits along the Ohio River.2 Further detailed information on the fluorspar industry in the United States is given by Hatmaker and Davis.28 Fluorspar is marketed according to the following relative quantities and specifications: Consump- Specifications, Per Cent Use Form tion in 1936, Per Cent CaF2 SiO2 Fe2O3 Metallurgical Gravel 79 +85 -5 or lump Ceramic,. Ground 10 +95 -3 -0,1 Acid Ground 11 +98 -1 The concentration of the coarser sizes presents relatively little diffi-culty, good recoveries being obtained with jigs and tables. However, sizes smaller than about 10 mesh cannot be successfully treated by ordinary gravity separation methods and so have been accumulating as

Jan 1, 1938

By M. G. Corson

THE iron-silicon alloy series has always been one of the most puzzling among the binary alloys. Examining the well known mechanical properties of the iron-rich alloys only we meet the following situation: The ultimate strength and yield point of alloys worked and annealed under the usual conditions represent nearly a straight line function of the silicon content up to 4.5 per cent. silicon (Fig. 1). Starting at the ultimate strength of 35,000 lb. and at a yield-point of 16,000 lb. for pure electrolytic iron, one reaches a -maximum strength of 93,000 lb. and a maximum yield point of 74,000 lb. at 4.5 per cent. silicon. This corresponds to an increase in ultimate strength by 13,000 lb. per each per cent. of silicon added and nearly the same rate applies to the yield point. The data mentioned are taken from the investigation by T. D. Yensen,1 and while they do not exactly corroborate the results obtained by earlier investigators, they seem to be the most correct. Plastic properties of the alloys are controlled by a much more complicated relationship. Up to 2.5 per cent. Si, the elongation stays close to 50 per cent. (in 2 in.) and the area reduction amounts to 85 per cent., a situation that forms the usual feature of all alloys representing strictly solid solutions. The plasticity of the latter is always nearly equal to that of their base metal. Beyond 2.5 per cent. silicon, the situation becomes much more complicated Yensen observed an enormous drop in elongation and area reduction at about 2.65 per. cent. silicon, where the first hardly reaches 10 per cent. and the second is still lower; he found, however, a considerable recovery in plasticity at about 2.8 per cent. Si and up to. 4.5 per cent. Si it is represented by 20 per cent. for the elongation and 30 per cent. for area reduction.

Jan 1, 1928

By Frank Firmstone

. In the early decades of the past century the method of starting iron blast-furnaces by " scatlolding-down" seems to have been in universal use for coke-furnaces and, at least in this country, for charcoal-furnaces also. It was likewise used at some of the early anthracite-furnaces, as is stated in the important " Reminiscences" printed by the late Samuel Thomas.' It had been generally superseded in Great Britain as early as 1850, by some variations of the plan now used, and was rarely used when Percy wrote.2 On the Continent it was still followed ill the 60's; and was elaborately described by Valerius in 1852. I have never read any statement as to when and by whom " scaffolding " was first dispensed with, but the following extracts from journals of my father seem to fix an authentic date for an instance in this country: " [Pittsburg] July 12, 1838.—Went with Major Wade to his foundry,etc., and he gave me a letter to D. Tyler, Esq., Farrandsville, Agent Boston Coke & Iron Co." " [Lockhaven, Pa.] July 18, 1838.—Heard there was a flat-boat going to take some gentlemen up to Farrandsville. Got on boat and to Farrandsville, 5 or 6 miles, in 1 hr. 30 min. Dined, and then delivered my letter to Ma Tyler, who showed me much attention, and everything belonging to the furnace, and had the water turned on the wheel that I might see the blowing-cylinders at work. There are two cylinders, 6-ft. stroke, -56 in. in diameter, but they find that one makes more than enough blast for the furnace. The furnace has 16-ft. boshes, 7-ft. tunnel-head, and is 47 ft. high, 3 tuyeres, and 3 heating-ovens [hot blast-ovens]. A

Jan 1, 1908

Organization Place Date 1917 Mine Inspectors Institute of U. S. A Indianapolis, Ind. July 9-11 American Society of Sanitary Engineers Grand Rapids, Mich. Aug. 1-3 National Association of Stationary Engineers... Evansville, Ind. Sept. 10-15 National Exposition of Safety and Sanitation.. New York City Sept. 10-15 American Iron, Steel & Electrical Engineers.... Philadelphia, Pa. Sept. 10-14 American Institute of Metals Boston, Mass. Sept. 24-29 American Foundrymen's Association Boston, Mass. Sept. 24-29 Chemical Industries, Third National Exhibition. New York City Sept. 24-29 American Electro-Chemical Society Pittsburgh, Pa. Oct. 3-6

Jan 7, 1917

By W. A. Koehler, M. E. Hinkle

INTRODUCTION THE oxidation of pyrites and marcasite in coal-mine strata to produce discolored acid mine drainage has long been explained by chemical reactions occurring in three stages: I. The iron sulphide minerals are oxidized by air in the presence of water to produce a nearly colorless solution of fer¬rous (iron) sulphate and some sulphuric acid. 2. The ferrous sulphate and part of the sulphuric acid combine with additional oxygen to form ferric (iron) sulphate. 3. The ferric sulphate hydrolyzes to form a reddish-brown precipitate and additional sulphuric acid. Nevertheless, chemical data alone are not sufficient to explain all observed facts. The first stage seems to proceed more slowly in the chemical laboratory than in nature. The second and third stages nor¬mally occur to a marked extent within a few days with raw mine water. However, the visible discoloration that characterizes these latter stages will not develop for months if the mine water is sterilized. By means of bacteriological techniques, two organisms have been isolated from acid coal-mine drainage. These are believed to have a part in promoting the chemical reactions summarized above. One organism is considered to be Thio¬bacillus thiooxidans, which is known to be able to convert elementary sulphur or sodium thiosulphate to sulphuric acid. Its relation to the formation of acid mine drainage has not yet been established. Apparently it does not promote the oxida¬tion of ferrous iron compounds in mine, drainage to the ferric state. The second organism has not been identi¬fied by name but is described as "Gram negative, non-spore-forming rods approxi¬mately 0.4 micron wide by o.8 to 1.0 micron long." A pure culture of this when added to sterile mine water will cause the latter to become amber and develop the typical rusty precipitate. However, it has not been found to convert sulphur com¬pounds to sulphuric acid. Further research is planned to determine whether or not these microorganisms play a significant part in the first stage of oxidation whereby pyrites and marcasite minerals go into solution. Some of the conditions found in abandoned sections of coal mines, such as a reduced percentage of oxygen and increased percentage of carbon dioxide in the air, as well as the existing temperature and acidity ranges, will be tolerated by and may even be favorable to these organisms. ACID COAL MINE DRAINAGE Acid coal mine drainage has been the concern of coal mine operators, industrial¬ists, sportsmen and public officials for many years. The amount of acid flowing into our streams in the coal-producing areas varies considerably from mine to mine and from

Jan 1, 1948

By Wm Price

THE object of this paper is to present a survey of some of the physical properties of sheet nickel silver when subjected to cold rolling and when annealed at temperatures extending from 350° C. throughout the commercial annealing range. A number of alloys were taken from stock and analyzed. Four of these, representing low nickel and high nickel both with and without lead, were chosen for the tests. The analyses were as follows: ALLOY COPPER, LEAD, IRON, NICKEL, MANGANESE, ZINC, PER CENT. PER CENT. PER CENT. PER CENT. PER CENT. PER CENT A 64.68 Trace 0.194 - 6.73 0.06 remainder B 65.82 1.27 0.227 6.17 0.06 remainder C 65.44 Trace 0.345 17.83 0.08 remainder D 65.60 1.08 0.238 17.77 0.06 remainder These alloys were rolled in accordance with regular mill practice to approximately No. 6 B. & S. gage. The bars (which were then coiled) were annealed together in a mill muffle and afterwards pickled in a 10 per cent. sulfuric-acid solution and cold rolled in stages of approximately .one number (B. & S.) at a time to No. 18 B. & S. gage. After each stage, suitable samples were set aside for physical tests. Additional samples were chosen for tests after the bars were rolled to Nos. 8, 10, 12, and 14 gage. These samples were annealed together in the mill muffle and, after pickling, were finished on 0.050-in. gage, yielding a series of specimens 2, 4, 6, and 8 numbers hard for the subsequent annealing tests. Tensile test pieces 9 by 1 in. (22.9 by 2.5 cm.) were cut from both lots and the central portion was milled to give a test section 2 ½ in. long by ;Z in. wide. A distance of 2 in. was marked off on the edge of each specimen with light punch marks. In the case of the annealed alloys, Erichsen test pieces 4 by 2 1/2 in. were also taken.

Jan 10, 1920

By R. I. Jaffee, F. C. Holden, H. R. Ogden

ECENT papers dealing with the properties of unalloyed iodide titanium have been directed primarily at the determination of base-line properties for alloy investigations. Early work was limited to a few tests because of the limited availability of iodide titanium at the time. In the results of papers by Campbell et al.,1 Gonser and Litton,2 Jaffee and Campbell,3 inlay and Snyder,4 and Jaffee, Ogden, and Maykuth, data on mechanical properties are presented for unalloyed iodide titanium in the annealed and cold-worked conditions. Data are presented in this paper which show the effects of heat treatment on the structure and mechanical properties of commercially produced iodide titanium. Correlation is made between microstruc-tural variables and the mechanical properties. Experimental Procedures Melting Stock: The melting stock used was as-deposited iodide titanium, produced by New Jersey Zinc Co. The furnished analysis showed the following range of impurities: N, 0.004 to 0.008 pct; Mn, 0.005 to 0.013; Fe, 0.0035 to 0.025; Al, 0.013 to 0.015; Mo, 0.0015; Pb, 0.0045 to 0.0065; Cu, 0.0015 to 0.002; Sn, 0.001 to 0.01; Mg, 0.0015 to 0.002; and Ni, 0.003. Hydrogen content as determined by vacuum-fusion analysis was 0.0091 wt pct (0.44 atomic pct) after arc melting and fabrication. Nitrogen analysis on the arc-melted and fabricated titanium showed a content of less than 0.002 pct N. The average hardness of the furnished stock was Rf 70, or approximately 85 VHN. Melting Procedure: The as-deposited rods were rolled, sheared, and degreased in preparation for arc melting. The charge was arc-melted with a tungsten electrode in a water-cooled copper crucible under a positive pressure of high purity (99.96 pct) argon. The final ingot was approximately 2 in. in diameter and showed no increase in hardness over that of the initial stock. Fabrication: Heating for fabrication was done in air. It was begun by forging the ingot into a 3/4 in. diam rod, at an initial temperature of 1600°F. Scale was removed by sandblasting. The rod was then swaged to 1/4 in. diam at room temperature through a series of 20 dies, with approximately 10 pct reduction in area between each die. An anneal of 1 hr at 850 °C in air was given after the 1/2 in. die, such that the final cold reduction was 75 pct. Sections cut from this rod were used for test and microstructure specimens. Heat Treatment: Heat treatments were carried out in resistance tube furnaces with stainless-steel linings, under an atmosphere of gettered argon. As further protection against contamination, the specimens were packed in titanium turnings in a titanium sleeve. Control experiments have shown negligible hardness increases with this method, indicating that contamination from oxygen and nitrogen is slight. Three cooling rates were employed in this work; these have been designated as water quenching, argon cooling (to simulate air cooling under a controlled atmosphere), and furnace cooling. The cooling rate for an argon cool is 100°C per min for the first minute, with an average cooling rate of 35°C per min over a 15-min period. A furnace cool requires about 10 hr, with an average cooling rate of 3.6oC per min during the first hour, and an average cooling rate of 1.2°C per min over the 10-hr period. Microimpact Test: The specimen adopted was based on the cylindrical Izod Type Y specimen (ASTM, E23-41T). All dimensions were reduced to half scale, including the notch radius. Specifications are shown in Fig. 1. The specimen is held vertically in an adapter and broken as a cantilever beam. Impact tests were run on a constant-velocity (11.34 ft per sec) Tinius Olsen impact testing machine with a total available energy of 100 in.-lb. Tests were made to determine the correlation between this microimpact and the standard V-notch Charpy impact test. Curves showing impact energy as a function of temperature for both impact tests are plotted in Fig. 2. Transition temperatures, when they occur, are about the same for both impact tests. All three titanium-rich materials have the same conversion factor, 10. Tensile Testing: Tensile tests were conducted on Baldwin-Southwark testing machines using the 600, 2400, or 3000 1b range. Specifications for the test specimen were taken from the 1948 edition of the ASM Metals Handbook, and are shown in Fig. 1. Strain measurements were made using an SR-4 resistance gage (Type A-7) cemented to the reduced section in conjunction with a lever-type extenso-meter. Readings on the SR-4 strain indicator were

Jan 1, 1954

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933

By H. H. Podgurski, H. E. Knechtel

Annealed Fe-Al alloys do not react readily to form AlN when held at 500ºC in NH3-H2 gas mixtures, but do so upon the introduction of dislocatims. Nuclea-tion of the nitride phase occurs on dislocation sites. In turn, the growth of the aluminum nitride particles causes the ferrite phase to yield plastically, generating more dislocations for the nucleation process. The nitride phase extracted from an Fe-2 pct A1 alloy nitrogenated at 500°C was identified as stoichio-metric aluminum nitride with a hexagonal crystal lattice. THIS investigation reveals the role that dislocations play in initiating and sustaining the nitriding reaction in Fe-A1 alloys. As early as 1931 the work of Meyer and Hobrock1 suggested that the initiation of the nitriding reaction could involve a nucleation controlled process. Recently Bohnenka2 depicted the gas-phase nitriding process below 600°C as one of mixed control limited by nitrogen penetration through the surface, by nitrogen diffusion, by aluminum diffusion, and by nucleation of the nitride phase, Fig. l(a). In our research in a comparable alloy (0.57 pct Al) at 575ºC, we have observed a nitrogenation which we feel is better described by Fig. l(b). In the case of a 2 pct-A1 alloy partially nitrided at 500°C we propose the profiles shown in Fig. l(c). For a complete and accurate description of the process, a concentration profile of the dislocation density in the test specimen would be needed. EXPERIMENTAL Nitrogenization was conducted between 500" and 575°C in a variety of NH3-H2 gas mixtures on three Fe-A1 alloys: 1) zone-refined iron + 0.16 i 0.2 pct Al—levita-tion melt, 2) zone-refined iron + 0.57 0.02 pct Al— levitation melt, 3) plastiron + 2 pct Al—melted by induction heating. To demonstrate the effect of dislocations on reactivity, both cold-worked and annealed samples were investigated. All nitrogenation rate studies were conducted gravimetrically with a gold-plated invar balance4 contained in a gas-flow system. To avoid contamination of the specimens in the reaction zone of the system, the reaction chamber was constructed of high-purity dense alumina. The activity of nitrogen was fixed by specific NH3-H2 gas mixtures whose compositions were continually monitored by calibrated thermal conductivity gages and checked by chemical analysis. Variations of ± 0.1 pct NH3 could easily be detected by both methods. Throughout this paper the activity of nitrogen is defined as PN3 /PH23/2 , where PNH3, and Ph2 are partial pressures in atmospheres. Electron transmission, density measurements, and chemical analyses were made on specimens before and after nitrogenating in order to reveal structural and chemical changes. Similar studies as well as X-ray diffraction studies were conducted on nitride extractions from the nitrogenated 2 pct-A1 alloy. These extractions were obtained by the use of an anhydrous bromine-methyl acetate solution which dissolves the iron and leaves the insoluble nitrides as a residue. Hardness profiles were obtained on cross-sections of partially nitrided specimens to demonstrate the extent of nitriding through the thickness of the specimens. RESULTS AND DISCUSSION The nitrogen activity in the NH3-H2, atmospheres was never allowed to reach a level capable of producing iron nitride (Fe4N). Hence, the term nitriding as used in this paper refers only to the formation of aluminum nitride whereas nitrogenation refers to the total uptake of nitrogen regardless of how it is distributed throughout the alloy. The weight increases observed during the initial stage of a nitrogenating treatment are due primarily to the solution of nitrogen in the ferrite phase, particularly when starting with annealed specimens. Because this initial nitrogenation rate in the case of the 0.57 pct A1 alloy, see Figs. 2 and 3(a), was most rapid the weight change that occurred thereafter might be attributed to the nitriding reaction with the exception of a small weight increment due to the irreversible pickup of oxygen by aluminum. The oxygen (<70 ppm) came from traces of H2O and 0, in the hydrogen and ammonia gases. On the basis of discrepancies between total weight increase and the increase in the nitrogen content of the sample as determined by chemical analysis, it was estimated and later established by activation analysis, that as much as 200 ppm of oxygen were taken up by a fully nitrided Fe-0.57 pct A1 specimen at 575°C. Most of the oxygen could have been picked up from the nitriding atmosphere on the surface of the samples during cooling to room temperature. Even 50 ppm of water in the gas phase will become oxidizing to iron before the sample has cooled to room temperature. The lack of reactivity* of these alloys in the annealed

Jan 1, 1970

By R. M. Asimow, J. J. Svitak

Tile crilical resoll,r,d shear stress, CRSS, for slip of slow1y cooled Ag-All single crystals was measured at 201K. Tlze importance of short-range order and Suzuki sogregalion was inrestigated by deter~rlining llze ciic.cl of quenching on the CRSS. Thr obserz.ed rfrtenching effects were generally small and indicate that short-range ordcr and Slczuki srgregation do no1 account for n significant portion of the solid-solution strengthening in this system. However, all alloys slzozcwi yield drops ulhich rilere heat- lreat nrenl-sensiline THERE have been a number of mechanisms proposed to explain alloy strengthening in the Ag-Au system. The effectiveness of some of the proposed mechanisms, especially those that depend on Suzuki segregation1" or on short-range order,2-6 SRO? should be strongly dependent on heat treatment. Since internal friction investigations in this system indicate that there is stress-induced order,&apos; we must also consider the possibility of local atomic rearrangement or short-range ordering in the stress field of a dislocation. There is not complete agreement whether these mechanisms should be most effective in raising the flow stress, in causing yield drops. or some combination of these two effects. This work was undertaken to determine the effects in the Ag-Au system of mechanisms that depend on segregation or order by using known but drastically different cooling rates following a high-temperature treatment. By comparing the critical resolved shear stress, CRSS, for slip measured after a very slow cool and again after a fast cool (quench) of the same crystal, it is possible to determine the effect of cooling rate on CRSS* and on yield drops. The single-crystal CRSS was determined at several compositions because there has been no data published across the phase field since the publication of room-temperature flow stress by Sachs and Weerts.&apos; EXPERIMENTAL PROCEDURE Starting with materials of 99.999 pct purity, single-crystal specimens of random orientation 1.25 mm square by 4 cm long were prepared with 0, 10, 14, 25, 30. 50, 70. 75. 80, 90. and 100 at. pct Au. Crystals were grown in an inert atmosphere using a modified Bridgman technique with a growth rate of 1.5 cm per hr in a gradient of 3°C per cm. To obtain a maximum practical degree of SRO, the crystals were cooled at a rate of 275&apos;C per hr to about 310°C and then cooled at 6°C per hr to approximately 200°C. Specimens were tested in tension immersed in an alcohol bath at -72°C (201°K) at a strain rate > = 0.003 mm"1 to determine the CRSS (7). The activation volume of several crystals was determined from the flow stress increment (72 - T1) for a tenfold increase in strain rate. The total shear strain varied from 0.05 to 2.3 pct but was generally less than 0.4 pct. After testing, each crystal was then held at 500°C for 10 min, quenched into brine at -35°C and. after storage at -71°C for 1 day, retested in tension using a procedure identical to that of the first test. The quenching apparatus, see Fig. 1, was designed to enable accurate temperature control and rapid quenching while preventing specimen contamination and accidental deformation. Test data from a specimen with a fine thermocouple spot-welded to it indicated a cooling rate of 104C per sec. The relatively low heat-treatment temperature was chosen to minimize quenching defects caused by a large vacancy

Jan 1, 1970

By B. C. Wonsiewicz, G. Y. Chin

THE presence of deformation bands in cold-worked metals is known to influence the development of deformation textures1 but has not been considered in any theoretical treatments. At the present time the most rigorous theory of deformation textures appears to be based on Taylor&apos;s concept of homogeneous deformation of a crystal within a polycrystalline aggregate.&apos; For each crystal the Taylor theory allows the operation of several equivalent combinations of five or more slip systems. Hence deformation bands can arise from the operation of a separate combination of slips in each of several portions within a crystal. On the other hand, a second type of band may occur as a consequence of slip on systems other than those selected on the basis on homogeneous deformation. This type appears to be associated with crystals of symmetrical orientations, such as the [loo] and [lll.] axial orientations in drawn wires of fcc single crystals studied by Ahlborn.3 In this note we propose a simple mechanism of deformation banding of the second type, and compare the theoretical results for wire drawing of [loo] and [Ill] with Ahlborn&apos;s observations. In outlini the model requires that the work to accomplish a given overall shape change by banding be less than or equal to the work to accomplish the same change by homogeneous deformation. While the work by homogeneous deformation, WH = ?T ;dri, can be calculated exactly by the equivalent methods of Taylor2 or of Bishop and Hill,4 the work by banding, WB, is less certain. The latter consists of 1) Wi, work by slip within a band, 2) Wb, work associated with formation of a boundary between bands, and 3) Wc, work to correct the difference in shape change arising from banding and homogeneous deformation. The Wi term can be evaluated explicitly for a band with an assumed set of slip systems, but a satisfactory analysis of Wb and Wc has not been obtained. Since WB = Wi + Wb + Wc WH, for banding to occur, however, a necessary condition is Wi = WH . Hence it seems reasonable to choose a band with the lowest value of Wi among competing bands consistent with Wi = WH, and then minimize Wb and Wc by arranging the physical configuration of the selected band. Wc is minimized by combining neighboring bands such that their net strain matches the macroscopic strain as closely as possible, and Wb is minimized by enforcing strain compatibility across the boundary between two neighboring bands, similar to the case of a grain boundary.5 It is realized that this procedure is not completely satisfactory, but it does seem to explain Ahlborn&apos;s observations reasonably well. The procedure is now outlined for the two corner orientations. a) [l00]. Fig. 1 shows a (100) stereographic projection. The results of the Taylor analysis for axi-symmetric flow by homogeneous deformation6 show that, while [loo] itself is unstable, the rotation of the tensile axis will nevertheless be confined to within about 15 deg from [loo]. Alternatively, less work may be expended by banding with slip on a pair of systems with primary-conjugate relationship, e.g., (ll1)[10l.I + (li1.)[110]. The latter represents minimum Wi for all possible bands.* Since there are four symmetrically

Jan 1, 1970

By William Cruger

OUTLINE SUMMARY A. Brief Description B. Characteristics 1. Can be highly cost effective 2. Restricted in usage 3. Political Controversy 4. Volume of Transactions 5. Users C. Mechanism 1. Five steps D. Investor issues 1. Application 2. Restricted usage 3. Discount 4. Formal or informal process 5. Restricted benefits 6. Recompense 7. Window of opportunity THE VARIOUS PROGRAMS1 A. Brazil B. Chile C. Venezuela D. Argentina E. Mexico USAGE IN THE MINING, METALLURGICAL, AND PETROLEUM INDUSTRIES

Jan 1, 1990

By R. D. Pehlke, J. F. Elliott

The equilibrium pressure of nitrogen gas over pure silicon metal and silicon nitride has been measured in the temperature range 1400° to 1700°C. From the experimental data, the standard free energies and enthalpies of formation of Si3N4(a) have been calculated as functions of temperature over the above temperature range. Utilizing data in the literature and the results of this investigation, the specific heat, molar enthalpy, molar entropy, standard enthalpy of fornation, and standard free energy of fornation are estimated for the temperature range 298° to 1400°C. THE high-temperature thermodynamic properties of many metallic nitrides are not well established at present. This is a serious deficiency because nitrogen and nitride-forming metals are important alloying additions to steels, and knowledge of the interaction between nitrogen and these elements is essential to a better understanding of the behavior of steels. Metallic nitrides also are used as refractory materials. Consequently, the investigation reported here was undertaken to provide more complete information on the standard entropy and free energy of formation of silicon nitride. The experimental technique provided a direct measurement of the equilibrium pressure of nitrogen gas in the range of 1413 to 1700°C for the reaction: 3 Si(1) + 2N2 (g) = Si3N4 (a) [ 1 ] and below 1413oC for the reaction: 3Si(c) + 2N2(g) = Si3N4(a) [2] APPARATUS The experimental system consisted of a crucible assembly, a reaction chamber, and a gas supply and vacuum system. The Crucible Assembly which contained the equilibration specimen and molybdenum radiation shields with a susceptor for induction heating is shown in Fig. 1. Two covered, high-purity alumina crucibles, one nested within the other, contained the susceptor, shields and specimen. Central openings in the upper shield and crucible covers permitted on optical pyrometer to be sighted into the central cavity of the specimen. The specimen itself was a 5/8 OD by 1-in.

Jan 1, 1960

NEW MEMBERS The following list comprises the names of those persons who became members during the period Aug. 1, 1916, to Sept. 10, 1916: ALLEN, Louis M., JR., Chief Mine Sampler, Old Dominion Min: & Smelt. Co., Globe, Ariz. ATKINSON, CHESTER, Min. Engr., Asst. Supt., Smelt. Dept., Cerro de Pasco Mining Co., La Fundicion, Peru, South America. BAKER, CLAIR LINCOLN, Genl. Mgr., Mexican Dept., Amer. Smelt. & Ref. Co., 1108 Mills Bldg., El Paso, Tex. BARROWS, WALTER A., 3d, Asst. Supt., Blast Furnaces, Thomas Iron Co., Hellertown, Pa. BARTHOLOMEW, GEORGE POMEROY, Asst. Cons. Engr., Guggenheim Bros., 120 Broadway, New York, N. Y. BILLOW, ELMER E., Pres., National Supply Co., 416 NN-rest Grand Ave., Chicago, 111. BROWN, SAMUEL ROLLINS, Mill Supt., The Plymouth Cons. Gold Mines, Ltd., Plymouth, Cal.

Jan 10, 1916

By Henry M. Howe, Joseph Winlock, Francis B. Foley

This investigation was undertaken for the purpose of determining, in a systematic way, the effect of the rate of cooling of steels, heated to above the transformation range, on their various mechanical properties. This paper gives the results obtained in the investigation of the heat treatment of carbon steels carried out under the auspices of the Committee on The Heat Treatment of Carbon Steels of the Engineering Division, National Research Council. The objects of this committee, of which Dr. Henry M. Howe was chairman, were to increase knowledge of the influence of heat treatment on the mechanical properties of carbon steel. The mcthod pursued was to subject specimens of steel of the carbon contents most used for engineering work, 0.34 per cent., 0.52 per cent., and 0.75 per cent., to various heat treatments, and to test the mechanical properties thus induced. The steels were the same as were used by the committee on fatigue phenomena. This project was financed jointly by the U. S. Bureaus of Mines and Standards; industries and university laboratories have cooperated. A large part of the work was done at Doctor Howe&apos;s private laboratory. The committee consisted of F. B. Foley, H. AT. Boylston, H. C. Boynton, G. K. Burgess, H. J. French, J. H. Hall, Zay Jeffries, R. S. Johnston, F. C. Langenberg, H. F. Moore, E. H. Yeirce, H. S. Rawdon, W. E. Ruder and 11. J. Stagg. The work was undertaken at the suggestion of Doctor Howe, who thought, at the outset, that steel in the sorbitic state might have properties which, for most engineering purposes, would be better than those of the usual or pearlitic state. By a systematic variation in the heating

Jan 1, 1923