Search Documents

By N. H. Jensen

SINCE the sixties, Utah has been one of the leading metal mining states of the Union. During the last fifteen years its mines have supported the largest smelting center in the world. Its rank as a metal producing state is reflected by its 1924 production which had a value in excess of $65,000,000 making it the leading silver producing state, third in both copper and lead and sixth in gold production. During the past year, metallurgical developments for the recovery of zinc contained in lead ores has made rapid progress so that the future zinc output will be of substantial importance. The largest silver mines of the nation and the world's largest open cut copper mine are within its borders. Settlement of Utah started in 1847, with the advent of the "Mormons," and originally the area of the state was much greater than now. The first metal mining

Jan 1, 1925

By G. S. Ansell, J. Weertman

The creep behavior of an aluminum alloy hardened with a finely dispersed phase of aluminum oxide was investigated. The as-extruded alloy shows an approximate steady-state creep in which the creed rate depends exponentially on the applied stress. The activation energy of creeb is abbroximately 150,000 cal per mole. The recrystallized alloy shows no steady-state creep. ONE method of improving the creep resistance of a metal is to introduce a finely dispersed second phase into the metal matrix. The improvement of the creep resistance has been qualitatively explained by assuming that the dispersed second-phase particles act as obstacles to dislocation motion. If the main effect of second-phase particles is simply to hinder dislocation motion then it is possible to derive a high-temperature creep equation for a dispersion-hardened alloy in a straightforward manner. In the Appendix of this paper such an equation is derived from a creep model which works very well for pure metals. Recently, F. V. Lenel has fabricated, for the first time, powder extrusions of aluminum-aluminum oxide in a large-grained recrystallized form. This alloy, designated as MD 2100, consists of a fine dispersion of aluminum oxide plates in a matrix of commercial purity aluminum. A considerable amount of investigation has been carried out concerning the microstructure and physical properties of this alloy.&apos; ) The aluminum oxide is present in the form of flakes 130A units thick and 0.3 u on edge. They are dispersed in the aluminum matrix with an average spacing of approximately 0.5 jx. The spacing varies in the range of 0.05 to 1.5 µ. The alloy structure is extremely stable at high temperatures. For this reason the alloy offers a unique opportunity for a fundamental study of creep of a very finely dispersed two-phase alloy. Lenel supplied specimens in both the unrecrystallized and recrystallized condition. This paper reports high-temperature creep experiments carried out on these specimens. The results obtained were rather unexpected. No steady-state creep was observed in the recrys-tallized material. In fact, after some transient creep which takes place upon loading, the creep rate is essentially zero ( < 10-8per min). If the second-phase particles acted solely as obstacles to the motion of dislocations, measurable steady-state creep would be expected. Since none is observed it appears that the main effect of the fine dispersion in the recrystallized material is to inactivate the dislocation sources themselves, rather than hinder the motion of dislocation loops created at these sources. EXPERIMENTAL DETAILS Specimens were tested in wire form, 0.087 in. in diam for the as-extruded alloy, and 0.035 in. in diam for the recrystallized alloy. These samples were held in friction-type wire grips; a gage length of 2.5 cm was used for all the creep tests. The specimens were held at 600°C in the test apparatus for at least 15 hr prior to each test. The tests were run under the condition of constant loading and, since the creep strains were small, can be considered as constant stress tests. The temperature of testing was held constant within 3°C. Elongations were measured with an optical cathetometer which was capable of measuring strains as smaIl as 0.00012. This allowed the measurement of strain rates as low as l0-8&apos;per rnin. In addition to the creep tests optical micrographs were made in order to determine both the grain size and microstructure of these materials. RESULTS Fig. 1 shows a few typical creep curves obtained from the as-extruded material. The elongations were somewhat erratic, but each curve shows a region of quasi-steady-state creep from which an approximate steady-state creep rate can be obtained. In general the higher the stress at a given temperature, the greater the total elongation before fracture. The lower the applied stress, the longer is the region where the creep rate is almost constant. Summary data from the creep tests of the as-extruded material are listed in Table I. The steady-state creep data of the as-extruded material for a range of stresses at a constant temperature follow a creep equation of the type creep rate = K&apos; = A exp (&) [11 where A and B are constants, k is Boltzmann&apos;s constant, T is the absolute temperature, and a the stress. The standard error of estimate of the data received is less than one order of magnitude. As shown in Fig. 2, if one compensates the creep-rate data for the effect of temperature over the range of test temperature, the steady-state creep data roughly follow a creep equation of the type Temperature compensated creep rate = K* = A exp

Jan 1, 1960

By S. H. Ash

SAFETY records have improved in all branches of the mineral industry. While annual production was rising from $2 billion in 1910 to nearly $12 billion in 1950, fatalities decreased from 3539 in 1911 to 974 in 1951. And, although safety progressed under hand methods, it progresses more effectively under modern, mechanized methods. But powered devices such as electric or diesel units can in themselves create new hazards unless proper safeguards are instituted. Health Use of diesels underground is increasing. Diesel equipment has been used in construction of 34 tunnels in 16 states in the last 17 years. The 77 noncoal underground mines in 24 states using diesels underground range from mines with large open stopes to those with narrow veins, so that the ventilating problems represent a good cross-section of U. S. mining. The U. S. Bureau of Mines has received no report that anyone has suffered ill effects from the proper use of properly maintained equipment. The necessity for correct maintenance and use of satisfactory exhaust conditioners cannot be emphasized too strongly.

Jan 2, 1954

By Guido Del Giudice

THE term "slime-coating" is not new in the art of flotation; the phenomenon has been observed and described by Taggart;(1)? Taggart, Taylor, and Ince;(2) and by Ince.(3) Notwithstanding that flotation was introduced for the treatment of finely crushed ore, the adverse effects of slimes have been recognized since the earliest days of the process, and the Elmore, Delprat, Potter, and other processes actually specified desliming of the ore prior to treatment. The cause of this trouble has been studied and described by Taggart;(1) Taggart, Taylor, and Ince;(2) Ince; 3 Morrow and Griswold;(4) and by Gaudin and Malozemoff.(5) OLD THEORY OF SLIME-COATINGS At present, so far as published work shows, there seems to be but one theory for the mechanism of slime-coatings. Ince(3) states that they are due to attraction between electrostatic charges of opposite sign on the sulfide and, on the slime particles, supporting this theory by migration experiments in the Burton tube. He also used the microscope in conjunction with a glass cell employed by Beans and Eastlack(6) in studying migration, but met with interference from endosmosis. Several attempts have been made in the Department of Mineral Dressing at Columbia University to duplicate Ince&apos;s experiments with the Burton tube, but the results have never been convincing. Formation of precipitates which settled through the pulp levels, and evolution of gas at the electrodes, which disturbed the interface between the pulp and the distilled water above it, seriously interfered with observations. However, by use of the migration cell shown in Fig. 1, endosmosis effects and the disturbances due to precipitation and gas evolution were avoided, and distinct and reproducible migrations or absence of migration were observed.

Jan 1, 1934

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,&apos; who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.&apos; The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers&apos; salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber&apos;s salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954

Joseph W. RichaRds, South Bethlehem, Pa. (communication to the Secretary*): The hold experiment of Mr. James Gayley in drying the blast used in the Isabella furnace has attracted the attention of the whole metallurgical world, and has given rise to a wide discussion of the reasons for its great success. Mr. Gayley and the capitalists who backed him in his work deserve congratulations on the success of the venture, not only because it succeeded, but because they have been rewarded far beyond the maximum that could be expected from theory or probability. To state the case in its simplest terms, all that could have been predicted was: (1) that the removal of the moisture from the blaet would result in the saving of the heat required for its decomposition, representing from 3 to 5 per cent. of the heat-value of the coke used; hence about that quantity of fuel might be saved; (2) that the furnace would be somewhat more independent of variations in the weather; (3) that the campaign would be a little hotter; and (4) that the speed of the blowing-eugines would be decreased, at least in amount proportionate to the reduction in temperature of the air led to them. I do not think anyone anticipated a much larger output per day. The results actually attained were: (1) the furnace made an increase of 24.86 per cent. in the output of pig-iron per day; (2) it consumed 19.6 per cent. less coke per ton of pig-iron made; (3) the blowing-engines were run 15.8 per cent. slower; and (4) the saving in power made up for the power required to run the refrigerating-plant. In addition, the blast was hotter; the waste-gases cooler, because of their smaller volume; and there was a greater proportion of carbon dioxide to carbon

Jan 1, 1906

By John V. Beall

Probably it won&apos;t happen to us again in a thousand years, but it was very embarassing at the time. It is only because of certain matters that have come up this month that we tell you at all about it. At the beginning of our trip to Peru and Chile last summer, we were flying with Bill Haddon from Lima to Tacna aboard Fawcett. Being an old hand at foreign travel, particularly in South America, we felt obliged to explain some of the special features of travel in Latin America and the niceties of etiquette in particular and were so engaged when the plane landed at the airport. We led the way briskly into the terminal, expecting at any moment to have a representative of Southern Peru Copper pop up and present himself. However, this didn&apos;t happen so we repaired to the baggage arrival station to wait. All the bags were quickly picked up, but ours were no where to be seen. Bill was slightly agitated because the plane was being buttoned up for take off. However, rising to the emergency with our usual aplomb, we took charge of the situation. Brandishing the claim checks under the nose of the porter who pointed to them and said, "si, Tacna," we nodded briskly and in our serviceable Spanish said "si se[n]or, vayase viejo, rapido." He was off and back with our suitcases quickly enough.

Jan 1, 1970

By W. M. Baldwin, J. T. Brown

The effect of hydrogen on the ductility, c, of SAE 1020 steel at strain rates, i, from 0.05 in. per in. per rnin to 19,000 in. per in. per rnin and at temperature, T, from +150° to —320°F was determined. The ductility surface of the embrittled steel reveals two domains: one in which and the other in which The usual "explanations" of hydrogen embrittlement are in accord with the first of these domains only. THE purpose of this investigation was a fuller A characterization of this of the investigation effects of varying temperature and strain rate on the fracture strain of hydrogen-charged steel. To be sure, it is known that low and high temperatures remove the embrittlement that hydrogen confers upon steels at room temperature,1 * see Fig. la and b, and that high strain rates have a similar effect,&apos;-&apos; see Fig. 2a, b, and c. However, the general effect of these two testing conditions on the fracture ductility of hydrogen-charged steels is not known, i.e., the three-dimensional graphical representation of fracture ductility as a function of temperature and strain rate is not known—only two traverses of the graph are available. The need for such a graph is not pedantic. To demonstrate this point, Fig. 3a, b, and c shows three of many three-dimensional graphs, all possible on the basis of the two traverses at hand. The important point (as will be developed in the Discussion) is that each of them would indicate a different basic mechanism for hydrogen embrittlement. It will be noted that the four types of ductility surfaces in Fig. 3a, b, and c may be characterized as follows: Material and Procedure Tensile tests were made at various temperatures and strain rates on a commercial grade of % in. round SAE 1020 steel in both a virgin state and as charged with hydrogen. The steel was spheroidized at 1250°F for 168 hr to give the unembrittled steel the lowest possible transition temperature. The steel was charged cathodically with hydrogen as follows: The specimen was attached to a 6 in. steel wire, degreased for 5 min in trichlorethylene, rinsed with water, and fixed in a plastic top in the center of a cylindrical platinum mesh anode. The assembly was placed in a 1000 milliliter beaker containing an electrolyte of 900 milliliters of 4 pct sulphuric acid and 10 milliliters of poison (2 grams of yellow phosphorous dissolved in 40 milliliters of carbon disulphide). A current density of 1 amp per sq in. was used which developed a 4 v drop across the two electrodes. All electrolysis was carried on at room temperature. Temperatures for tensile tests were obtained by immersing the specimens in baths of water (+70° to + 150°F), mixtures of liquid nitrogen and isopen-tane (+70° to —24O°F), and boiling nitrogen (-240" to-320°F). Specimens were tested in tension at strain rates of 0.05, 10, 100, 5000, and 19,000 in. per in. per min. The 0.05 and 10 in. per in. per rnin strain rates were obtained on a 10,000 lb Riehle tensile testing machine, the 100 in. per in. per rnin rate on a hydraulic-type draw bench with a special fixture, and the 500 and 19,000 in. per in. per rnin rates on a drop hammer. The fracture ductility of hydrogen-charged steel at room temperature and normal testing strain rates (-0.05 in. per in. per min) is a function of electro-lyzing time, dropping to a value that remains constant after a critical time.&apos;* Under the conditions of • The hydrogen content of the steel continues to increase with charging time even after the ductility has leveled off to its saturated value.&apos; this research the saturated loss in ductility occurred at approximately 30 min, see Fig. 4, and a 60 min charging time was taken as standard for all subsequent tests. After charging the steel with hydrogen, the surface was covered with blisters. These have been described by Seabrook, Grant, and Carney.&apos; The original diameter of the specimen was not reduced by acid attack, even after 91 hr. Results The ductility of both uncharged and charged specimens is given as a function of strain rate in Fig. 5, and as a function of temperature at four different strain rates in Fig. 6. These results are assembled into a three-dimensional graph in Fig. 7. It is seen that the locus of the minima in the ductility curves of the charged steels divides the ductility surface into two domains. At temperatures below the minima,

Jan 1, 1955

By Holbrook Botset

EXPERIMENTS performed in this laboratory on the flow of gas-liquid mixtures through unconsolidated sands have been described and discussed in an earlier paper.4 In these earlier experiments a definite relationship was found between the liquid saturation of a sand and its permeability to the liquid or gas phase. Furthermore, the nature of the sand, the permeabilities of the sands over a range between 17 and 260 darcies, appeared to have a negligible effect upon the saturation-permeability relation. Likewise experiments indicated that the viscosity of the liquid, or the substitution of an immiscible liquid for the gas phase, had only a very slight effect on the permeability-saturation relation. This con-clusion has since been definitely confirmed by the experiments of M. C. Leverett3 on the flow of oil and water through unconsolidated sands. The sands used by Leverett were of very low permeability (between 6.8 and 1.04 darcies), while the oil-water viscosity ratio varied between 90 and 0.057. Since the sands that constitute petroleum reservoirs are largely con-solidated, although of widely varying degrees of consolidation, it was desirable to extend the experiments on gas-liquid mixtures to consolidated sand. In the study of consolidated sands additional variables are involved, but for the initial experiments the only new variable to be intro-duced was the cementing material.

Jan 1, 1939

By E. T. Turkdogan, P. Grieveson

Experimental results are given for the rate 0.f solution of nitrogen in y iron in the temperature range 1000° to 1200°C. It is shown that, when purified reacting gas is used, the rate-controlling process is the diffusion of nitrogen into the iron. The difhsiuity of nitrogen in y iron is calculated from the results and the equation logD = —(8800/T) — 0.04 is recommended to represent the temperature dependence of the diffusivity. In some experiments using unpurified nitrogen, solution rates are found to be slower than those attributable to a solely solid-state diffusion process. Indications are that in the presence of impurities in the gas, e.g., H,O, chemisorption of nitrogen at the surface is hindered and becomes a rate-controlling process for the transfer of nitrogen across the gas -metal interface. ALTHOUGH the solubility of nitrogen in y iron at known nitrogen activities has been well-established,&apos;-a the kinetics of the solution of nitrogen in iron are not known. The work of Darken, Smith, and Filer&apos; indicates that at temperatures below about 1300°C the rate of solution of nitrogen in y iron is controlled by a chemical reaction at the metal surface, while at temperatures above about 1300°C the rate-controlling process is the diffusion of nitrogen in the metal. Fast and verrijps studied the denitro-genization of y iron using wet hydrogen at 950°C and their results clearly indicate that the rate of nitrogen removal is controlled by diffusion of nitrogen in the metal. In Part I of this series of papers, the kinetics of the solution of nitrogen in y iron are discussed in the light of the present experimental work. EXPERIMENTAL Apparatus. The reaction chamber consisted of a platinum wire-wound resistance furnace with a re-crystallized alumina reaction tube. The temoerature of the furnace, which was automatically controlled to approximately 1°C, was measured with a Pt/Pt-13 pct Rh thermocouple and a potentiometer. The temperature distribution in the working zone of the furnace was determined using a calibrated Pt/Pt-13 pct Rh thermocouple and the hot zone was found to be approximately 3 in. long with a temperature variation of * 3°C. A series of experiments was also carried out at 1000°C and pressures above atmospheric using a pressure vessel which was similar in construction to that described elsewhere.1° Materials. Ferrovac E grade iron used in all ex-

Jan 1, 1964

By Charles Albert Ashburner

The coal-fields of the United States have been variously classified as to their geographical positions. In 1887 I proposed slight changes to the classification generally used, for more convenient description of our coal-fields in my report on the statistical history of coal in the States during 1886 for the United States Geological Survey. This new classification seems to meet all practical requirements and has been generally adopted. The coal-areas are grouped in two divisions—the anthracite division and the bituminous division. The anthracite division, in a commercial sense, may be said to include the anthracite districts of Pennsylvania alone, although small amounts of anthracite are mined in Colorado and have been

Jan 1, 1890

By Joseph Kuti

ROOF SUPPORT DEVELOPMENTS IN LONGWALL (1) European longwall mining technology developed towards its modern form in relatively deep mines. With increasing depth the stability of openings driven for ventilation, travel or transport becomes paramount in mine design considerations. As a result the number of roadways and entries, as well as their width must be a minimum. (1) Another important aspect of European mining is the high density of mineable seams, as opposed to the wide lateral extension of a single seam in the U. S. A. Multi-seam mining requires strict planning and near 100% extraction, since with increasing depth, the effect of remnant pillars can be devastating. As a result the face layout of a modern European longwall panel is based on single panel entries of moderate width and great height. The mode of extraction is generally a mixture of the advance and retreat system which is called a 2-system. It is obvious, therefore, that the supports developed for the entries and for the intersection areas are more complex than those in the U. S. A.

Jan 1, 1981

By R. E. Cech, J. H. Hollomon

KURDJUMOV and Maksimova reported experiments with manganese steels and high carbon steels&apos; and with an Fe-Ni-Mn alloy&apos; in which mar-tensite was formed isothermally over a range of temperatures. They found in some cases that mar-tensite formation could be suppressed by rapid quenching to liquid nitrogen temperature. From their microstructural observations of martensite formed isothermally, they concluded that the rate controlling step is nucleation rather than growth. Kulin and Cohen,3 in an attempt to reproduce these experiments, found that with a steel having the same composition as that reported by Kurd-jumov and Maksimova, the transformation to martensite was essentially complete above the temperature range of Kurdjumov and Maksimova&apos;s isotherms. The possible reasons for this disagreement were not considered. Recent papers by Das Gupta and Lement4 and Kulin and Speich5 report the formation of isothermal martensite in a high chromium steel and in an Fe-Cr-Ni alloy, but neither paper can be considered a verification of the original Kurdjumov and Maksimova results. Further, in neither case were the authors able to suppress the formation of martensite entirely. Because of the important bearing the Kurdjumov and Maksimova results have to an understanding of the mechanism of martensite reactions it was felt that an experimental investigation directly concerned with checking the validity of their results was in order. This paper describes the results obtained on the isothermal transformation over the temperature range from —79" to —196°C of an alloy of iron, nickel, and manganese. Experimental Apparatus A 15 lb heat of an alloy containing 73.3 pct Fe, 23.0 pct Ni, and 3.7 pct Mn was melted by induction and cast under argon. The ingot was forged to 1-in. bar and a portion rolled to 1/16x1 1/2-in. strip. This strip was pack-homogenized 300 hr at 1100" in a helium-filled sealed iron tube. The composition after homogenization was 73.2 pct Fe, 22.94 pct Ni, 3.73 pct Mn, 0.05 pct C, and 0.015 pct N. The strips were cut to 1/2-in. width for dilatometer and metal-lographic specimens. Only the center portion of the 11/2-in. strip was used in the present investigation. The dilatometer employed was similar in design to one described by Flinn, Cook, and Fellows." A concentric fused auartz rod and tube assembly with hooks for holding the specimen was mounted so as to transmit the specimen dilation to a 1/10,000 in., 1/10 in. travel dial gage. The dilatometer proper was mounted by means of extension arms to a counterweighted sliding member on a vertical standard. This method of mounting permitted rapid transfer of the dilatometer from the austenitizing furnace to the quenching bath and low temperature chamber. A small electrical vibrator on the dilatometer kept frictional effects of the quartz members at a minimum. The austenitizing unit was a vertical, molybdenum-wound, hydrogen atmosphere furnace maintained at a constant temperature ±3°C by means of constant power input. A 12-in. stainless steel jacketed copper liner having 1/2-in wall thickness acted to equalize the temperature in the hot zone of the furnace. This liner, closed at the bottom end and open at the top to permit entrance of the dilatometer and specimen, was kept filled with dry nitrogen gas. A chromel-alumel thermocouple was placed inside the tube to determine the temperature. The 4-in. dilatometer specimens in the chamber varied less than 1/2° across the specimen length except for a 1 1/20 drop at the end nearest the open end of the furnace. The low temperature isothermal holding bath was a double Dewar arrangement similar to one described by Turnbull7. The outer bath was filled with a refrigerant at a temperature lower than the desired holding temperature. The inner bath was filled with Freon "11" or "12" or a mixture of both, depending upon the holding temperature. This inner bath which tended to be cooled by the outer bath was kept at a constant temperature by introducing a small amount of heat with a manually controlled electric heater. Stirring was accomplished by bubbling dry air through the bath. A Leeds and North-rup type K potentiometer was used to measure the inner bath temperature as indicated by a five element copper-constantan thermopile. The bath temperature was maintained within ±0.2°C of the desired temperature by occasionally adjusting the heater current so as to keep the Leeds and Northrup galvanometer at zero deflection with a constant setting of the potentiometer. Isothermal tests were usually continued for 300 to 400 min and another reading made at approximately 1000 min if the bath, unattended overnight, had not deviated in temperature more than 5°C. Transformation curves are drawn dashed (Fig. 1) through the time region where temperature was not controlled precisely. Experimental Procedure Dilatometer specimens of 1/2x1/16-in. strip were cut to 41/2-in. length and holes were drilled for the quartz hooks with proper spacing to give a 4-in. measured length. A thermocouple consisting of 0.012-in. diameter chrome1 and alumel wires was spot welded to the specimen and threaded between the dilatometer rods to binding posts near the dial

Jan 1, 1954

By David M. Hopstock, Jose M. Pastrana

The magnetic susceptibilities of samples of natural and artificial hematite and natural goethite were measured by the Faraday method as functions of temperature, magnetizing field strength and particle size. All samples showed weak ferromagnetism, which accounted for large variations in susceptibility with field strength and particle size. Three probable sources of the weak ferromagnetism were identified.

Jan 1, 1978

By Freeman Bishop

The Nation&apos;s capital has one over- riding minerals-metals question: How long will prices and wages continue to move upward at the inexorable pace of the last year? Is the wage pattern to settle this year around 10%? The big industrial unions are coming into line, some of them later this year. Steel is standing in the wings for next year. Copper, steel, nickel and most other industrial metals have taken big hikes in their stride. Aluminum, which is making inroads into areas of industrial use formerly sacred to copper and some other metals, seems to be fighting to hold down its prices to attract customers from the higher-priced metals.

Jan 1, 1970

By H. F. Gossenberger, J. J. Tietjen, J. J. Gannon, C. J. Nuese

External quantum efficiency measurements at 300" and 77°K are presented for vapor-grown GaAs and GaAs1-xPx electroluminescent diodes as a function of junction depth and doping. In GaAs, external efficiencies are found to decrease exponentially with increasing junction depth, defining an average absorption coefficient of 900 cm-1 at 300°K and 350 cm-1 at 77°Kfor epitaxial layers of p-type GaAs. It is shown that photon absorption losses dominate at room temperature and, in fact, account for most of the external efficiency degradation between 77° and 300°K. Healever, the internal (&apos;junction) quantum efficiency is also found to decrease by a factor of 3.5 between 77" ALTHOUGH rapid progress has been made in recent years with GaAs, Gap, and their alloys for use in electroluminescent diodes, there are still important unknown factors related to the performance of these de- and 300°K. The dependence of GaAs efficiencies on donor and acceptor concentrations is presented, illustrating best efficiencies at donor concentrations of 1.5 to 2x 1018 cm-3 . External efficiencies are found to be independent of acceptor concentrations less than 3 x 1019 cm-3 but to degrade at higher doping. The fabrication of GaAsi-xPx electroluminescent diodes is briefly discussed. External efficiencies here for planar uncoated diodes are about 0.035 pct at 300°K and 0.4 pct at 77°for x = 0.42. A brightness of about 8500 ft-Lamberts is attained at 77°K and of 315 ft-Lamberts at 300° K. for curvent densities of 10 amp per sq cm. vices. For example, although the external efficiency is known to decrease by factors of typically 10 to 30 between 77°K and room temperature, the exact causes of this are still uncertain. Experimental results of ill&apos; and carr2 with zinc-diffused electroluminescent diodes suggest that this external degradation is almost entirely due to increased absorption losses at room temperature, with a relatively temperature-independent internal efficiency; recent calculations by Gonda et al.3 corroborate this hypothesis. In contrast, Pilkuhn and Rupprecht4 find the internal efficiency of solution-grown GaAs laser diodes to degrade from 100 to 66 to 40 pct as the temperature is increased from

Jan 1, 1969

By S. Warren Hobbs

The section of the Northwestern United States that includes the northern Rocky Mountains and adjacent areas to the west and east is one of large mineral production and important mineral potential. The metallic ore deposits vary widely in age and type and their geologic settings are similarly diverse. A brief resume of the region's physiographic characteristics and geology sets the framework for the selected ore districts that are described in following papers and makes it possible to place these ore deposits in their proper reference to space and time.

Jan 1, 1968

By C. S. Barrett, A. Smigelskas

There have been no publications of the deformation and recrystallization orientations of the metal beryllium, yet pronounced textures would certainly be anticipated since it is close-packed hexagonal in structure. Having an axial ratio approximately that of magnesium, beryllium probably deforms by nearly the same slip and twinning mechanisms that operate in magnesium, and the textures are likely to be similar or but slightly different from the magnesium textures. In the tests reported below this is found to be the case; the textures are found to differ from those of magnesium only in the details of the scatter from the average orientation. This report covers not only samples rolled at room temperature, but some rolled at elevated temperatures. Since magnesium has been suspected by some investigators of altering its crystallo-graphic deformation mechanism at elevated temperatures, it was considered possible that beryllium might do so and alter its textures accordingly. No pronounced alterations were found, however. Unfortunately, the theory of deformation textures is not in a state of development that permits one to deduce the deformation mechanism from a knowledge of the textures, which means that the similarity of textures at different rolling temperatures, reported here, cannot be taken as definite evidence that the deformation mechanism is actually the same at all temperatures. The general similarity of the deformation textures of magnesium and beryllium also extend to the recrystallization textures of the two metals, judging by the pole figures for recrystallized sheet presented in this report. Samples were prepared in the form of composite sheets made up of small pieces stacked in a pile. Each piece was trimmed with scissors so that an edge was parallel to the rolling direction, dipped in paraffin, and assembled into the pack by aligning it under the cross hair of a microscope. As the desired orientation was obtained on each piece it was secured in place by touching with a hot wire to melt the paraffin. A stack of ten or fifteen pieces was built up in this way, then trimmed to the shape of a T; the portion to be X rayed was then etched to the shape of a wire about 0.045 in. diam with 6N HCl. This method of shaping the sample is a modification of that used by Bakarian on magnesium.&apos; The absorption of the rays in the sample was so slight that it caused no difficulty in interpreting the films. Exposures were made with a 0.030 in. diam pinhole, using molybdenum radiation (40 kv, 25 ma, Type A film at 5 cm, 2 to 3 hr exposures). With the recrystallized specimens it was found necessary to oscillate the specimen so as to reduce the spottiness of the lines. A range of oscillation of 5" was SUB- cient to produce reasonably satisfactory patterns, though the quality was somewhat inferior to that of the deformation texture patterns, and only two degrees of intensity were read from the arcs on the films. Typical photo-grams for each of the deformation textures and the recrystallization texture are assembled in Fig 1. The pole figures were plotted in the usual way with the intensity of the various portions of the diffraction rings estimated by eye. Seven to nine films were made of each sample and each was carefully read in plotting the pole figures. Typical series included exposures with the beam normal to the rolling direction and at 11, 26, 41, 56 and 71" to the cross direction, plus two exposures with the beam normal to the cross direction, and at 11 and 79" respectively to the rolling direction. The rolling was in each case considered sufficient to develop the final texture: the reduction by cold rolling was 84 pct (from 0.0045 to 0.0007 in. thickness), following prior hot rolling in longitudinal and transverse directions and recrystallization; the reduction by hot rolling at 800°C was 90 pct (0.010 to 0.001 in.), following similar prior treatment; the reduction by rolling at 350°C was 88 pct (from 0.005 to 0.0006 in.) after similar prior treatment. The recrystallization texture was determined on a sample rolled at 350" to a reduction of 88 pct (0.0165 to 0.002 in.) after similar prior treatment, then mounted between steel strips to keep it flat and annealed at 700" in an atmosphere of argon. Discussion of Results The results of the X ray determinations are assembled in the pole figures of Fig 2, 3, 4 and 5 for rolling at

Jan 1, 1950

By J. Farkas

A techno-economic assessment for the recovery of several elements from seawater is presented. Gold recovery has been used as an illustration for the economic evaluation of several processes. Current technology does not present any economically viable alternative to recover gold from seawater because its concentration is several magnitudes too low. However, with the increasingly larger availability of concentrated seawater, mainly from desalination and other processes, coupled with advances in technology, especially genetically modified specific microorganisms, may make the recovery of gold and other desired elements from seawater a reality in the near future.

Jan 1, 1984

By S. H. Ash

IN no part of the world other than a small area in Pennsylvania is anthracite mining an industry of major magnitude. As the deposits of anthracite in the United States are limited virtually to Pennsylvania, the difficulties of this industry have been commonly considered a state rather than a national problem. However, there is also national interest in the conservation and wise utilization of all the country&apos;s fuel resources and in the control of interstate waterways. The anthracite industry is confronted with a serious problem of water accumulation in many of the mines, a problem that must be solved in the near future if progressively higher mining costs are to be avoided. It cannot be solved by the operating companies without state or Federal aid, or both, owing to the magnitude of the work required, the diversity of interests of the coal and surface ownerships, the hazard to the whole mining community, and interests affected outside the mining region. &apos;The costs of abating the ever-increasing surface seepage to mine workings and of handling this seepage once it has occurred are beyond the eco¬nomic resources of the operating managements.

Jan 1, 1941