Search Documents

By T. Szendrei and S. Tose

Historical approaches to the problem of flyrock based on correlation studies and regression analysis, including artificial neural networks and similar techniques, are inherently incapable of addressing two core issues – root causes of flyrock and projection velocity. A further shortcoming of correlation techniques is that they give no information on the influence of rock size and shape on the flight distance. The scaled depth of burial model for crater blasting in the collar zone and bench face does not specifically address the question of flyrock velocity. A third approach, based on flight trajectory calculations, often neglects the very significant effects of air resistance on the trajectory. Some trajectory models incorporate air resistance but use an implausible fragment velocity model that cannot propel sizeable rocks to distances much beyond 150 m. Nonetheless, trajectory calculation incorporating the effects of air drag affords the most promising approach to the prediction of flyrock range. A unique and insightful feature of the proposed realistic flight modelling is that it collapses all suspected causes of flyrock, many of which are not well understood, to just a single parameter – the launch velocity. This indicates that the root causes of flyrock lie in the mechanisms of momentum transfer to broken rock and suggests new avenues of study.

Dec 13, 2022

By A. Y. Senchenkoa, Y. V. Kulikov

The relationships revealed between ore hardness and specific energy consumed by crushing and grinding are described in the paper. A comparison of key technical and economical parameters of SAG and HPGR circuits is made, based on testing of several ore types for greenfield projects. The comparison of results make it possible to estimate efficiency of the technologies application, depending on ore hardness and taking into account potential risks for a circuit under design. Keywords: Comminution circuits, SAG, HPGR, test results

Jan 1, 2020

By I. Ince, S. Kahraman, M. Rostami, B. Dibavar

The density, porosity, and strength of rocks are fundamental in the design of geo-engineering projects. Determining these properties requires the preparation of smooth core samples, which is usually impossible for soft rocks. Besides, only fragmented samples may be available in some projects. A method for predicting rock properties from rock particles such as drilling debris would therefore be useful. This study was undertaken to develop prediction equations for compressive strength (UCS), tensile strength (BTS), density, and porosity values from the crushability index (CI) obtained from rock fragments. The results showed that UCS, BTS, density, and porosity were strongly correlated with the CI. The physical characteristics and strength of rocks may be predicted with the help of the derived equations. The CI test is a valuable tool for estimating rock properties in drilling projects and in situations where core specimens are not available.

Mar 14, 2024

By K. A. Annan

The last seven hot rolling passes of the ferritic stainless steel AISI430 were simulated on a Gleeble-1500D® thermo-mechanical simulator to investigate the effect of temperature, strain rate, and interpass time on the texture. The compression tests were carried out over a wide range of strain rates (0.1 s-1 to 5 s-1) and temperatures (1100°C to 820°C) with different interpass times (2, 10, 20, and 30 seconds). The dynamic recrystallization to dynamic recovery transition temperature was determined from examining the relationship between the mean flow stress and the inverse of the deformation temperature in multi-pass tests. It was found that the texture in the central layer of the compressed sample is a strong recrystallization-type. The through-thickness textural and microstructural banding, to a large extent, were found to be weakened by hot deformation in the two-phase (a+ ?) region, as opposed to the single-phase (a) region.

Jan 1, 2013

By T. Mahlangu Mahlangu, T. Fungene, K. C. Sole

"Although oxygen is widely employed as the oxidant of choice in gold leaching by cyanide, its low aqueous solubility presents some drawbacks in practical application; hydrogen peroxide has therefore been considered as a possible alternative. The aim of this investigation was to study the catalytic decomposition of hydrogen peroxide, which generates an oxidizing intermediate species, and to understand its effect on cyanide destruction. Operating conditions that facilitated the effective decomposition of hydrogen peroxide were established by varying the pH and catalyst type and concentration. The oxidizing intermediate, detected using an indirect technique, was found to be the hydroxyl radical (OH?). OH? is commonly generated in acidic solutions, but this work demonstrated that it is also produced at the alkaline pH values necessary for cyanide gold leaching. The effects of free and complexed iron and copper catalysts on the oxidation and consumption of hydrogen peroxide and cyanide were also investigated. It was shown that the cyano complexes of Fe(II) and Cu(I) are also effective as decomposition catalysts. Hydrogen peroxide concentrations above 0.01 M decreased the free cyanide concentration, which was attributed to the probable formation of the cyanate anion (CNO-). Although cyanide consumption increased due to its oxidation in the presence of OH?, excessive cyanide consumption in the presence of copper was attributed primarily to its complexation by the unstable copper(I) cyanide species. Rate constants for the decompositions of H2O2 and cyanide by ferrocyanide and copper cyanide were calculated; the latter was identified as being a better catalyst. IntroductionLeaching of gold from its ores using cyanide has been employed for well over a century (Habashi, 2016). Addition of cyanide converts the gold into a cyanide complex (Au(CN)2 -) that is soluble in water (Wang and Forssberg, 1990). The leaching reaction can be represented as Equation [1]:"

Dec 1, 2018

By B. P. Watson

In South Africa, the Bushveld platinum group metal deposits are unique in that they are the largest platinum group metal deposits in the world. These deposits occur as two distinct stratiform tabular orebodies and strike for many hundreds of kilometres. Mining is extensive, with depths ranging from close-to-surface to 2 000 m. The mining method is a variation of planar open stoping. Pillars are widely used to support the open stopes. Crush pillars are commonly used in this role, where the residual pillar strength provides the required support resistance to stabilize the stoping excavations. This paper describes the direct measurement of stress within these crush pillars, and describes the stress?strain behaviour of these pillars. These findings indicate that the measured pillar failure stress is too high. The implications of these findings are that roof damage and pillar bursting could occur, and some examples of this type of damage are shown. The paper concludes that this problem could be mitigated if the three dimensional pillar geometry were modified and the pillars were cut smaller.

Jan 1, 2007

By E. Molobi

"Studs are rods threaded on both ends and are used as mechanical fasteners for two or more components. Stud finds usage in industries such as automotive, construction and aviation. The advantage of studs is that they allow for disassembly of components during maintenance. Studs are continuously subjected to both tensile and shear stresses, depending on the application, therefore they should be manufactured from suitable materials that are capable of withstanding all these external forces. Studs are sometimes manufactured from re-sulphurized steel due to its improved machinability; however, there is a certain limit on the amount of sulphur, above which failure may occur. Premature failure of studs has been a common problem, but failed studs are commonly replaced with new ones without conducting failure investigations. The present work investigates the premature failure of two re-sulphurized steel studs used on a rocker arm assembly and recommends alternative materials. The investigation was carried out by conducting visual examination, microstructural analysis, hardness measurements, chemical analysis and a detailed scanning electron microscopy (SEM) investigation on the fracture surface.IntroductionTwo rocker arm studs used on a 16-cylinder diesel locomotive engine failed prematurely after being in service for less than 5 months. The rocker arm studs had a life-cycle of 5 years. The studs were manufactured from resulphurized steel. The paper aims to establish whether re-sulphurized steel is applicable for the manufacture of studs in the automotive industry.BackgroundLocomotives are classified as either electric or fuel-powered. Diesel locomotives are an example of fuel-powered locomotives. This type of locomotive uses a diesel engine as a means for propulsion. An engine converts chemical energy into mechanical energy required for traction. In an internal combustion engine a rocker arm is an oscillating lever that conveys radial movement from the cam lobe into linear movement to open and close poppet valves of cylinders (Husain and Sheikh, 2013). The rocker arms are secured on to the cylinder head by rocker arm studs."

Jan 1, 2016

By A. K. Raji, E. F. Orumwense, M. O. Ojumu

This research paper introduces a novel passive method for ocean mining using an electricpowered robotic subsea dredging crawler designed to operate in various subsea conditions, including unstructured and rough terrain. The electric-powered robotic subsea dredging crawler is equipped with two driving tracks and features a complex assembly of tank tread chain link, tank tread idler wheels, tank tread sprockets, bronze bushings, motor hub, motor mount, and a 12-volt direct current motor. To evaluate the performance of the electric-powered robotic subsea dredging crawler, it was compared with existing ocean hydraulic exploration crawlers, such as MK3 ROST, in terms of drive performance on an inclined ramp with five angles of inclination (0°, 15°, 20°, 25°, 30°). The experiment aimed to determine the maximum velocity, torque, and efficiency of the crawler at different angles of inclination. The collected data were analysed and plotted using Python, and the effect of the electric-powered robotic subsea dredging crawler’s weight on its driving performance was also considered. The results of this study demonstrate a quadratic relationship between driving performance and inclination angle, which can be used to optimise the electric-powered robotic subsea dredging crawler’s performance for future ocean mining robot drive applications.

Oct 2, 2025

By J. P. Beukes

South Africa holds approximately three-quarters of the world?s viable chromite ore resources and dominates the global production of ferrochrome. Albeit completely unintended, small amounts of Cr(VI) are formed during ferrochrome production. Certain Cr(VI)species are regarded as carcinogenic, hence making the treatment of some ferrochrome waste materials necessary. In this paper, the Cr(VI) treatment strategies currently employed by the South African ferrochrome producers are investigated by means of a literature review and a questionnaire survey. From the discussion, it is evident that various treatment strategies are available to deal with Cr(VI)-containing waste in the ferrochrome industry. However, by far the most commonly applied treatment strategy remains the aqueous reduction of Cr(VI) with ferrous iron. The advantages and the correct application of this strategy, together with the disadvantages and pitfalls, are argued. Innovative improvements on historic practices are also discussed

Jan 1, 2012

By More-O&apos, R. C. Ferrall, J. W. Wilson

Discussion: M. D. G. Salamon* (Fellow): The theoretical principles behind the techniques of calculation used by the authors was formulated and published during the period 1962- 65. These principles, together with their practical implications, were summarized in a review paper in 1966.1 Now, in February, 1970, we have this long and comprehensive paper discussing the practical application of the theory. I think this is good progress. The large number of practical examples treated in the paper clearly demonstrates not only the skill and knowledge of the authors, but also the versatility of the techniques of analysis. I feel that the techniques described by the authors, and their improved versions, will revolutionize mine planning. I suggest that no shaft system or stoping layout should be planned in future without an adequate rock mechanics analysis. It seems that it will be progressively more difficult to white wash mistakes in rock mechanics and attribute their costly outcome to normal mining risk. We should not, however, become complacent. There is still a lot to learn and do in the future. I do not want to discuss tonight the question of further research but instead, I will raise two other problems which may hinder the future progress of practical rock mechanics. To carry out work similar to that described in the paper, mine managements require men who are capable of doing the work and who have the most efficient techniques of analysis at their disposal. As a research engineer I have been associated with the development of techniques of analysis. I can assure you that these have undergone an amazingly rapid development during the last six years. We have seen the change from the use of the electrolytic tank analogue and manual integration to the method described by the authors, that is, to the employment of the automatic network analogue and computer integration. But this is not the end. In a recent paper Prof R. P. Plewman2 and his co-authors described a completely digital technique. Here the process of calculating on- and off-reef quantities is integrated into one computer run. But these sophisticated methods of computation are useless without men to make intelligent use of them. During the last few years a new breed of mining engineers has appeared on the scene - the Rock Mechanics Engineer. I feel it is timely to call the attention of the senior members of this Institute to the fact that this new breed will succeed in carrying out its duties in a valuable manner only if we manage to attract to its ranks young engineers of the right quality. The requirements are high. The top rock mechanics engineers have to be good mine planners and they have to understand the essence of sophisticated theories. Without these attributes they will not succeed in the long term and the industry will not gain the benefit of available knowledge. To attract this quality of engineers the industry will have to ensure that rock mechanics is accepted by all concerned as a career which could lead to the top echelons of our profession. Finally, I would like to make one or two remarks concerning Part I of the paper. In Sections 3.1 and 3.2 the authors describe methods of determining the normal stress on the reef plane and the convergence distribution in the excavations. The description as given applies only to a horizontal reef. When the reef is inclined the situation is more complex since a shear component of stress on the intact reef and a ride component in the excavations must then also be determined. These can be calculated by methods similar to that described in the paper.3 The practical application of the method of calculating the released energy (Section 3.4) is in the comparison of various stoping layouts to establish an order of preference in terms of decreasing rates of energy release. To carry out these comparisons effectively, the calculations must be carried out in a manner by which the values of energy per unit area obtained are comparable. I would like to note in this respect that the method of calculation given in the paper is valid without reservation only if there is no elastic contact between the hanging and foot walls in the mined-out area. If there is contact then the calculated energy values are correct only if the mined out area is increased in small steps during the analysis. My second point in this regard is concerned with the practical method of calculation as described in Sections 3.4 (ii)-(iii). Firstly, I would like to suggest that the energy calculation should be carried out, as far as possible, by using always the same scale on the analogue. Secondly, the reading of current on a pin should be followed by the removal of that pin to obtain the corresponding reading of potential. The product of these two values will be proportional to the energy released during the mining of the small area corresponding to that pin. The method suggested by the authors tends to mask possible danger points in the layouts, since they obtain an average value for a time period, say, for six months.

By D. G. Krige

D. G. Krige: The stimulating contributions from Messrs Cooke, Curtis, Martus, Johnston, Van Wyk, Van Rensburg and Wroth are appreciated by the author and provide clear evidence of the importance not only of the principle of assistance to gold mines, but also of its scope and form. In general all the arguments, raised by Messrs Cooke, Martus and Johnston in favour of extending the scope of the new assistance scheme can be accepted as sound.

The Water Year Office for South Africa has supplied a provisional list of scientific congresses and meetings due to be held during 1970 with "Water" as the main or secondary theme, as follows: February: SARCCUS conference on "Water for Progress," Lourenco Marques. March 16-20: Annual Congress, Institute for Water Pollution Control, Cape Town. May: Possible S.A. Akademie conference on Cooling Tower Experiments, Pretoria. May: Annual Meeting of Association of Municipal Electricity Undertakings, Potchefstroom. May 27-29: Congress on "Water Resources of Natal", Durban. June 29/July 4: Annual Congress, South African Association for the Advancement of Science, Cape Town. July 2: Joint meeting of South African Association for the Advancement of Science and S.A. Akademie, Stellenbosch. July: Winter School, Federation of University Engineering Students. July: Youth Science Week. Foundation for Education, Science and Technology. July 21-24: The South African Tunneling Conference. September: Proposed SARCCUS conference on water in Nature Conservation, Skukuza. November 16-20: International Convention on "Water for the Future", Pretoria.

By G. R. W. Walker

A unique means of obtaining sea-water by G. R. W. WALKER, Pr. Eng., B.Sc. (Hons.) (Min. Eng.) (Member) Although the mining and treatment operations at The Consolidated Diamond Mines of South West Africa, Limited, are located within an average distance of I km from the Atlantic Ocean, the supply of clear sea-water in large and continuous quantities for use in treatment plants is made difficult by siltation of water-holes and the amount of sand in suspension in the sea itself. The need for sixty million litres of sea-water per day at the new No. 2 treatment plant necessitated the construction of a system that would ensure a continuous and reliable supply. Several sea-water intake schemes were proposed. This paper outlines the need for an improved means of obtaining water and describes the construction of the scheme eventually chosen - a tunnel driven through bedrock for over 400 m beneath the Atlantic Ocean. At the end of the tunnel, two large chambers were excavated from which vertical holes were drilled to intersect the sea-bed.

Jan 5, 1976

By C. Musingwini, A. S. Nhleko, M. J. Mahase

"In an environment like the mining industry, which is characterized by different stakeholders with multiple objectives, multi-criteria decision analysis (MCDA) is a useful approach for optimal decision-making. The application of MCDA techniques in the mining industry has predominantly been in mine planning and related problems, although no comprehensive survey has previously been undertaken to establish the application trends. A survey of the use of MCDA techniques was therefore conducted using case studies from the literature. It was noted that often two or more methods are applied to the same problem in order to increase confidence in the solution derived. As the number of criteria and alternatives increases, some methods become inefficient. A combination of the analytic hierarchy process (AHP) method with other MCDA techniques was the most frequently used approach, indicating the efficiency of the AHP method, especially when evaluating problems with more criteria and fewer alternatives. A combination of fuzzy theory with AHP or other methods incorporates uncertainty. The findings from the survey will benefit users applying MCDA techniques to solve mine planning and related problems.IntroductionA country’s natural resources serve the needs of different groups of people within the country. These different groups are collectively known as stakeholders (Herath and Prato, 2006). Stakeholders have different needs, preferences, and expectations, which describe and define the criteria to be considered in decision-making. The options available as solutions describe the alternatives in decisionmaking theory. The criteria and alternatives have to be evaluated simultaneously when making decisions, and this is when multicriteria decision analysis (MCDA) techniques become invaluable (Herath and Prato, 2006) because the human mind is considered to be limited when solving complex and intangible problems with several criteria and alternatives (Saaty, 2007). MCDA techniques belong to a broad group of techniques called multi-criteria decision-making (MCDM) techniques. The other group of techniques within MCDM comprises the multi-objective decision-making (MODM) techniques. MODM techniques are generally used to solve problems with an infinite number of alternatives, while MCDA techniques are generally used to solve problems with a finite number of alternatives (Musingwini, 2010)."

Jan 1, 2016

By G. A. Bezuidenhout, S. Bradshaw, W. Malan

"Currently, the matted-based collection process is most widely used for platinum group metal (PGM) recovery. However, because PGM-containing concentrates are becoming more enriched with UG2 (Upper Group 2) low-grade concentrates, this is expected to be integrated or replaced with an alloy collection process.The reduction LG (low-grade) concentrates with silicon carbide (SiC) was investigated. The purpose of the study was to ascertain the feasibility of using SiC as reductant with regard to metal fall, PGM grade in the alloy, slag composition, and overall PGM recovery, and if possible, the integration of such a process in the current matte-based collection process. Rowland and Easterns LG concentrate samples from Lonmin were analysed by Xray diffraction (XRD), X-ray fluorescence (XRF), and inductively coupled plasma mass spectrometry (ICP-MS). It was found that SiO2 and MgO are the most abundant oxides and Pd is the most abundant of the PGMs. Sulphide-bearing minerals such as chalcopyrite were detected in low concentrations (below 1%), and Cr2O3 concentrations are between 2-4%. SiC reduction of Rowland and Easterns concentrate were conducted at 1600°C with reductant to concentrate ratios ranging from 2.5 to 3.5 kg SiC per 100 kg concentrate.The reduction experiments revealed that PGM recoveries from Rowland concentrate were poor. SEM images showed entrained metal prills in the slag phase. The slag viscosity at the end of the melt was calculated by using FactSage, and the results indicated that the viscosity was higher than 4 poise, which is above that of Easterns slag. PGM recoveries for Easterns concentrate were significantly better. More than 85% of the Ir and Pd and almost 60% of the Pt were recovered in a test with a reductant to concentrate ratio of 3.5 kg SiC per 100 kg Easterns concentrate. At this reductant to concentrate ratio, Fe recovery was also the highest, at 66%. SEM imaging of a slag sample revealed few or no metal prills entrained. The FeO content in the initial concentrate charge was then increased by adding Peirce-Smith converter slag in order to decrease the slag viscosity and further increase PGM recovery. A test was conducted with the addition of 10 kg converter slag per 100 kg Easterns concentrate. The reductant to concentrate ratio was kept at 3.5 kg SiC per 100 kg Easterns concentrate. The Ir and Pd recoveries were more than 95%, while Pt recovery was almost 70%. Fe recovery increased to 76%. On the basis of these results an optimum feed ratio between Easterns and Rowland concentrates and Peirce-Smith converter slag were calculated. FactSage predicted that the concentrate charge should consist of 70-80% Easterns concentrate with 20-30 kg converter slag per 100 kg LG concentrate. SiC reduction of this optimum LG concentrate charge is expected to recover more than 90% of all PGMs. Cr and Si concentrations in the alloy will be below 1% in total.The effectiveness of SiC as reductant was also compared to carbon reduction. Carbon reduction of an optimum concentrate charge at the same reductant to concentrate ratio resulted in a marginally higher metal fall than SiC reduction. However, gas emissions and energy requirements are higher for carbon reduction.The study has shown that base metals and PGMs can be recovered in an iron alloy by SiC reduction of LG concentrate with converter slag additions. Integration of such a process into the matte-based collection process could be considered as a future alternative for smelting UG2 LG concentrates."

Jan 1, 2014

By S. Marx

More than twenty years ago Sasol, ISCOR, and some parastatals played a major role in ensuring that South Africa had sufficient technical skills. When the economy became tight and business and government were pressurized to decrease costs, the first budgets that were reduced were the training budgets. It seemed to be too expensive and too time-consuming to train apprentices. According to Stacey2, this is a major strategic issue facing the mining industry in South Africa. Two factors added to the shortage of skills challenge: ? Skills erosion and job losses ? Artisans ? currently the economy produces 5 000 but the need is 12 500 ? Level of mechanization in South Africa less than 10 per cent ? Average age of operators and artisans is 50 ? Greater awareness of occupational health effects of hand-held drilling. ? Workplace challenges ? The impact of HIV/AIDS and other employee wellness issues ? Changes and challenges in workplace environment i.e. the mining industry.

Jan 1, 2012

By S. M. Spottiswoode

A simple method for the application of excess shear stress (ESS) analysis to the mining of planar reefs is examined. The potential for seismicity associated with mining is expressed as the calculated increase in ESS on a regular grid of points 50 m above the reef, and is compared with observed seismicity around a deep-level, relatively geologicaly-undisturbed gold mine. Thirty regions were studied, involving over 2000 seismic events with magnitudes greater than 1,5 on the Richter scale and associated with almost 2 million square metres of stoping. The total seismicity, measured either as the number of seismic events or as the total radiated energy, corelated more closely with changes in ESS than with ERR. The incidence of rockbursts also favoured the ESS model. Corelation coeficients of around 0,8 for seismicity and ESS indicated that the assumptions inherent in the method used are collectively reasonable. The total seismicity in each region was found not to be strongly controlled by the presence of dykes and faults, although numerous individual seismic events were located close to such features.

Jan 1, 1988

By G. T. C. Emere, E. C. Hunter

The use of cylindro-conical settlers for the clarification of underground water by E. C. HUNTER- (Associate) G. T. C. EMERE-, B.A. (Hons.) (Keele) (Visitor) This paper analyses the performance of conical settlers on Harmony Gold Mine from 1959 to the present time, and describes the investigation that was undertaken to substantiate and improve the use of conical settlers for a new pump chamber in another part of the mine.

Jan 5, 1977

By O. Korhonen, T. Leskinen

The use of large OK-16 flotation machines at the concentrators of Outokumpu Oy by o. KORHONEN and T. LESKINEN(Visitors) The development ofthe OK-16 flotation machine is described briefly, and an account is given of its use at various concentration plants in Finland. The benefits arising from the use of larger flotation machines are listed, and the technical specification of the OK-16 machine is detailed in an appendix.

Jan 6, 1976

By G. R. Lane

A large opencast gold mining company in Africa had just completed a feasibility study for the expansion of the operations. A traditional net present value project valuation methodology had been used that showed a very positive net present value (NPV). The project team had conducted a qualitative risk assessment that identified and logged all potential project risks and had subjectively incorporated ?risk? via the discount rate and other assumption contingencies around gold price expectations, operating parameters etc. Management requested that an independent quantitative risk modelling approach be adopted to obtain a better understanding of the impact of risk on the overall project valuation and confidence level in the final valuation. A detailed project valuation model was configured in the Carbon Modelling Technology and the stochastic modelling module used to perform the Monte Carlo simulations. Analysis of historical operational performance data relating to actual achievements versus planned and budget determined the historical variability of the underlying parameters as well as variance to budget. This was done at a detailed level for mining rates and costs, processing rate, costs and recovery, and other operational efficiency measures. External market assumptions relating to gold price, exchange rate, and inflation were modelled and the dependency between them modelled using a copula. This case study will demonstrate the approach taken to building and populating the quantitative risk model and the overall results of the Monte Carlo simulation. The final valuation demonstrated that the project had a 44 percent probability of an NPV less than zero i.e. 44 percent chance of project finance loss.

Jan 1, 2012