Search Documents

By Wayne Charlie, Joseph P. Martin

INTRODUCTION Typically, uranium mills produce slurred tailings which are transported by pipeline to a tailings impoundment. The slurried tailings contain about 250 solids (75% liquids) by volume and, depending on the milling process, have a high or low ph. Despite decanting water from the tailings pond and losses by evaporation and seepage, Staub (1978) estimates that for lined impoundments over half of the input water is stored in the tailings. As long as the impounded tailings remain in a loose and saturated state, potential hazards exist and include potential for short and long-term seepage from the impoundments and the potential for large scale release and movement of liquified tailings should an embankment fail. The breach of an earthen dam on July 16, 1979 at Church Rock, New Mexico, and the subsequent release of 100 million gallons of water and liquified uranium tailings, underlines the potential hazard. Loose saturated tailings also have a high potential of liquefaction during earthquakes (Charlie and Wardwell, 1979; Martin, Finn and Seed, 1978; and Mittal and Morgenstern, 1976). If the tailings could be dewatered, the liner's integrity would become less critical, longterm seepage and settlements would be greatly reduced. In addition, the potential for tailings liquefaction from an embankment failure or earthquake would be greatly reduced. This paper reviews the concept, criteria, and design of various proposed interior drainage systems to dewater the tailings after deposition. ADVANTAGES OF INTERIOR DRAINAGE The primary purpose of interior drainage systems for uranium mill tailings impoundments is dewatering the tailings as rapidly and as thoroughly as possible. The expected benefits of this new technology are: • Reduction of potential seepage losses by decreasing the hydraulic head. • Reduce earthquake liquefaction potential of the tailings by inducing non-saturated conditions and/or lowering the water pressure. • Reduce the potential for large-scale release and movement of tailings should an embankment fail. • Stabilize the tailings to permit early reclamation. • Recovery and potential recycling of tailings liquid. • Inhibiting long-term seepage out of the impoundment by inducing nonsaturated conditions to provide capillary suction in the tailings.

Jan 1, 1980

By S. K. Kawatra, R. A. Seitz

Nonpolar hydrocarbon oils are commonly used in the flotation of minerals to fulfill a number of roles. These roles include reducing overall reagent costs by replacing part of the collector addition, improving coarse particle recovery without reducing selectivity, as well as several others. This paper will cover the types of oils which are available, their physical and chemical characteristics, and the effect of these characteristics on the function of hydrocarbon oils in flotation. In addition, techniques for improving the behavior of oils will be discussed.

Jan 1, 1986

By Christopher Mark

Area wide pillar failures, or “squeezes,” were once fairly common in underground coal mines. While rare today, they do occur. This paper describes seven case histories that were investigated by MSHA Technical Support. They occurred across the range of US coalfields, in both longwall and room-and-pillar mines, and involved development mining, pillar recovery, longwall panel extraction, and multiple seam interactions. Significant lessons from each are discussed.

Jun 25, 2024

By Fabio Amaya, Andrés Marulanda, Ramiro Gutiérrez, Alberto Marulanda

The behavior of a salt rock mass is strongly related to a creep phenomenon. The amount of creep depends on the level of stress generated in the underground excavation. Additionally, security conditions and the lifespan of an underground cavern excavated under this geological conditions depend on the evolution of creep. Based on the experience of the failure of the Old Underground Salt Cathedral of Zipaquirá(Colombia) and the construction of the new one, the theoretical framework to predict the creep behavior of a salt rock mass is explained. The theoretical formulations are calibrated based on actual observations of the material behavior to predict the lifespan of this striking structure.

Jan 1, 2003

By James G. Donovan, Mario G. Karfakis

A large percentage of Southern Appalachian coal reserves are located in seams less than 36" thick. As thicker and currently more mineable deposits are exhausted, methods of underground thin-seam extraction must be developed. Past experience with highwall mining of thin-seam coal has indicated that recovery rates tend to be lower than in conventional operations. It is suspected that this will also apply to underground thin-seam mining, regardless of proposed technology or mining method. Backfilling is one alternative for thin-seam coal mining; although backfill has been used extensively in hard rock mining its use in coal mining has been limited. The ability of backfill to provide additional ground support may enhance coal recovery by allowing for the design of undersized pillars. Backfill is capable of providing additional ground support by restricting lateral deformation of surrounding coal pillars and roof. This additional support can result in significant increases in recovery from thin-seam coal deposits. However, the overall feasibility of backfill is dependent on the in situ behavior of the fill material, the properties of the fill, the effects of the filling method on the total mining operation, and the cost of filling per extra ton of coal recovered.

Jan 1, 2001

By Randall E. Hughes, John F. Burst

This chapter describes the nature and occurrence of the principal clay minerals that are used as ceramic raw materials, explains how these raw materials are used to produce finished goods, and summarizes positive and negative trends that will affect future demand for raw materials and products in the ceramic industry. The term ceramics was derived from the ancient Greek keramikos (a clay jar). A ceramic product is a material that has been fired to at least 468.3°C (Mitchell, 1983). In addition to being one of our earliest manufacturing and construction materials, ceramic products are among the earliest records of civilization. The enduring significance of ceramics is shown by the fact that, even today, the manufacture of whitewares, brick and related red-fired wares, refractories, and engineered ceramics continues to be a major sector of the US economy. A wide range of materials can be made into ceramic products, although relatively few earth materials make up most of the ceramics in today's markets (Table 1). Most ceramic products are made from clay or a related material. The long history of clay use in the ceramics industry stems from its variable and sometimes unique physical and chemical properties, as well as its ubiquitous occurrence and relatively low cost. Clay is important to ceramics because of its plasticity, moldability and filterability, chemical content, color. refractoriness, solubility. corrosion resistance, electrical properties, and other properties that result from the essentially two dimensional morphology of the individual clay mineral platelets. Because of their basic relationships to the chemical and physical properties of clays, the chemical and mineralogical content have been the subject of continuous studies over the past few decades. Advances in knowledge about the chemical, mineralogical, and physical properties of clays are responsible for most of the advances in processing. The need to remove off-colored contaminants, minerals with low melting points, and soluble salts has resulted in beneficiation by wet processing methods such as water washing. Water washing is restricted to kaolins, although low cost methods of water washing have been extended more recently to ball clays in Europe. High intensity magnetic filtration and flotation technologies have noticeably improved the quality of kaolins and broadly expanded their use in the ceramics industry. In addition to products for construction (e.g., brick, tile, sewer pipe, field drain pipe, cement, fiberglass, roof granules, and paint) and manufacturing (e.g., refractories, kiln furniture, sanitary ware, pottery, and dinnerware), clays are used in calcined form as ceramic fillers, carriers, extenders, and grogs. Ceramics suppliers are under economic pressure in several of these product areas. Manufacture of refractories in America has declined as steel production has decreased. Similarly, dinnerware and tile production have declined because of foreign competition. Fortunately, new uses for clays,

Jan 1, 1994

By Neville G. W. Cook, John Kemeny

Utilizing the principles of elastic-brittle fracture mechanics, stress-displacement relationships are derived for an elastic solid containing a slip plane consisting of various configurations of collinear arrays of cracks. These models take into account the heterogeneous nature of slip planes as observed in the lab and in the field, and are relevant to the behavior of rock containing faults, joints, bedding planes, and fractures. All of our models exhibit slip weakening behavior, and show regimes of both stable (aseismic) and unstable (seismic) deformation. For given configurations of cracks and applied boundary conditions, our results show explicit ly the energy released through unstable crack growth. For instance, it is found that two equal length cracks growing together release more seismic energy than, say, a large crack growing into a small crack. Also, by allowing cracks to coalesce, our models show multiple stick-slip events without crack healing or other geochemical means.

Jan 1, 1986

By Jozef S. Stachulak, Bruce R. Conard

INTRODUCTION The concern of occupational exposure to diesel exhaust pollutants is an important workplace issue for the mining industry. During the last three decades of diesel operations at Inco, a significant amount of research and improvement has been made in the area of work environment, and effective diesel operation. This paper will review the experience gained by Inco's Ontario Division from the implementation and the use of modern engines, improved fuel quality, and the exhaust control technology, coupled with adherence to proper maintenance and ventilation design and practices. Past monitoring practices and the current occupational monitoring program at lnco are outlined. A major new research initiative involving multi-stake holders in diesel performance is described. MINING IN THE SUDBURY AREA The discovery of nickel-copper ore in the Sudbury area dates back to the year 1856. The existence of this orebody was noticed when a strong compass deflection was observed by a provincial surveyor. This discovery, even though documented in official re- ports, failed to arouse any public attention at that time. In 1884, a rock-cut was blasted through a small hill near the village of Sudbury to permit laying track for the Canadian Pacific Railway (Boldt 1967). The rock-cut uncovered a body of massive sulfides with a copper content of over nine percent. The mineralization is concentrated along the outer margin of the Sudbury Basin, an oval-shaped structure having a dimension of 55 x 95 kilometres. The ore extends down-dip to to at least 3000 metres below the surface. The mining methods at lnco can be divided into two categories: "filled-stope" and 'bulk" mining. This division, in the broad sense, may also reflect the environmental conditions of the mine. In the past, the selection of a mining method was based on the size, shape, grade and the strength of the ore and its surroundings. The recent development of improved technology and mining equipment permitted wider application of low cost bulk mining methods. UNDERGROUND DIESEL EQUIPMENT The first diesel-powered machine, a 145-horsepower scooptram, was put into operation in March 1966, in a cut-and-fill stoping complex at Frood Mine. The number of diesel machines underground in the Inco, Ontario Division, mines was increased to 360 units by 1971,550 in 1977 (Rutherford 1978), and over 830 diesel-powered units in 1995. The following list indicates current mobile diesel equipment. LHD 194 Loaders 81 Trucks 28 Jumbo Drills 78 Personnel Carrier 101 Service Equipment 155 Locomotives 50 Bolters 30 Scissor Lift 113 About 20 percent of the LHD and truck units are equipped with electronic fuel controlled engines. COMPOSITION OF DIESEL EXHAUST Diesel exhaust contains hundreds of pollutants (Watts 19921, including components of unburned fuel and lubricating oil and products of incomplete combustion of the fuel and oil. These pollutants are emitted either as gases or as particles. Gaseous pollutants include carbon monoxide, nitrogen oxides, and sulfur ox- ides, as well as a variety of organic compounds, such as hydro- carbons, aldehydes, and polynuclear aromatic hydrocarbons. The particle phase, also known as diesel particulate matter (DPM), is the filterable portion of diesel exhaust. Figure 1 depicts the trimodal particle size distribution that arises from different mechanisms of aerosol generation (Cantrell and Rubow 1992). Primary combustion aerosols, including diesel exhaust aerosol, are formed as very small particles (in the 0.001 to 0.08 micrometre range), but physical mechanisms such as condensation and coagulation quickly transfer the aerosol mass from the nuclei mode to the accumulation mode. These processes result in a mass median diameter of approximately 0.2 micrometres for diesel particulate matter, and 90% of the particles are less than 1.0 micrometre in size. These particles have a high surface area, permitting the adsorption of different substances produced during combustion. Mechanically generated aerosols, on the other hand, typically contain particles greater than 1 micrometre in diameter. The particle phases of diesel exhaust contain three components (Bagley, et al, 1996) shown by Figure 2, namely: a carbon- aceous fraction composed mainly of solid-carbon particles, a sulfate fraction containing small hydrated sulfate particles, and a soluble fraction that contains compounds that are soluble in organic solvents and are adsorbed or condensed onto carbon core particles. These compounds consist primarily of higher molecular weight hydrocarbons and PAH's and may contribute 15% to 45% of the weight of the total particulate matter (Schuetzle, 1983). The control of these pollutants is necessary to ensure a healthy work environment. Proper engine maintenance, engine design modifications, improved fuel quality, and use of exhaust control technology, coupled with good ventilation practices, all

Jan 1, 1997

By M. F. Gleason, S. Burns, J. R. Arnold

In 1986, Gold Fields began negotiations with a large Nevada electrical power utility to supply power for its Chimney Creek mine in northern Nevada. After the long negotiations reached an impasse over various costs associated with the power line, a decision was made by Gold Fields to generate its own power. Self-generation is not uncommon overseas, but it is rare for any but very large or very small operations in the United States. Surprisingly, under certain conditions a mine can generate its own power profitably, and Gold Fields has found that the associated operating and maintenance problems are minimal. The following report details what factors went into this decision and how it works. Hopefully, it can serve as a guideline for those who may find themselves in a similar position. History In the spring of 1986, Davy McKee Corp. was contracted by Gold Fields Mining Corp. to provide design engineering and construction management for the chimney Creek Mine. Chimney Creek is located about 50 mi northeast of Winnemucca, NV in a remote part of Humboldt County. The nearest industry using utility power was the Pinson Mine, about 13 mi from the proposed plant site. The existing electric line was not capable of carrying another mine the size of Chimney Creek, which required 29 million kwh per year. There were three options available to Gold Fields for the power supply: 1 )Power could be supplied by the public utility from a coal-fired plant about 30 mi away by constructing a new line to the mine,

Jan 1, 1991

By Donald W. Gentry

Mine valuation is a multifaceted, interdisciplinary process by which the economic viability of an old, existing, or new mining property or venture is determined. The problems associated with arriving at a representative and accurate value for a mining property are complex and numerous, and the procedures utilized in determining these values vary from simple, back-of-envelope calculations to sophisticated mathematical manipulations requiring computer modeling and analysis. Regardless of the complexity or the degree of sophistication associated with any particular project, the evaluation process must ultimately provide management with two basic types of information. First, the evaluation process should indicate whether or not the mining project is economically viable after careful consideration of all engineering, environmental, geologic, and other variables pertaining to the project. Second, the evaluation process should provide management in- formation on the relative attractiveness of the project when compared to other alternatives. In some cases, it may be extremely difficult to supply this information for a project directly. Nonetheless, the evaluation process should and must present all information necessary in a format which can be incorporated into the decision-making process as expeditiously as possible.

Jan 1, 1979

By M. Karmis

Surface subsidence has been recognized as an inevitable consequence of underground coal mining for several centuries. The damage resulting from this phenomenon has been witnessed in rural as well as in urban areas and ranges from simple land settlement to severe structural damage to buildings. Subsidence prevention is not feasible, at least under the existing technological and economic constraints of underground coal mining. Using a rational method of subsidence prediction, it has been demonstrated in many coalfields that subsidence control can be successfully practiced in order to reduce and accommodate subsidence within environmentally acceptable levels. This paper presents the development and testing of a subsidence model, based on the zone area method. This technique is a refined development of the influence functions and it is capable of investigating a mining plan of any shape, thus facilitating both longwall and room-and-pillar mining systems. More specifically, this study can be divided into two major efforts: (a) The development of the zone area model. This formulation was designed to accommodate the analysis of an optimum number of zones, over the area of interest, both accurately and efficiently. (b) The testing of the computer techniques with appropriate field measurements. In order to accomplish this, published as well as unpublished information was collected and analyzed according to a regionalized scheme. This procedure minimized differences in subsidence characteristics between the various coalfields and allowed a regional validation of the predictive capabilities of the model.

Jan 1, 1982

By Donald J. McKee

The product sizing and tonnage from a grinding circuit are the end result of a series of linked size reduction stages which always involve: fragmentation in mining; degradation in transport of ore; crushing and finally grinding. A case study is presented which illustrates the substantial effect on autogenous mill throughput of different mining practice. It is shown that it is possible to model each of the size reduction steps of fragmentation, degradation, crushing and grinding. The way in which this predictive capability is used is dependent on the operating constraints of each mine-mill combination.

Jan 1, 1998

By Robert P. Edwards, Brian C. Flintoff

Crushing plants (multiple stage) are an integral part of most conventional comminution circuits (ball mill, rod mill - ball mill). Although conventional circuitry is now the design exception, there are still many older, and some newer plants that include crushing in the process flowsheet. In most of these installations the operating objective is to maximize throughput at some minimum product size, in an effort to balance the comminution load between crushing and grinding. To achieve this goal, while avoiding production losses due to overloads, generally requires the use of automatic control strategies. This paper reviews the crushing plant control problem and describes several approaches that have been successfully implemented in different plants.

Jan 1, 1992

By Allen V. Reicks, Thomas J. Rudolphi

Computerization has allowed practical design of complicated and optimized belt conveyors for bulk materials from prediction of belt tensions around the belt circuit for a wide range of belt loadings and conveyance paths. These design methods are based on a knowledge of component operating characteristics and sources of tension change. As compared to generalized 'f' methods, CEMA's historical Kx and Ky has provided nonlinear and more specific predictions of belt tension as affected by various components and operating conditions. These empirical values were developed in a different age and generalizations made in their development are now a constraint to additional conveyor improvements. This paper discusses the potential from improved and standardized ‘friction’ predictions and presents the results of sensitivity evaluations as affected by calculation method

Jan 1, 2004

By J. W. Jang, J. J. Moore, I. Iwasaki

The wear behaviors of grinding media with different chemical composition and microstructures in wet grinding of a quartz-pyrrhotite mixture were investigated under various environments. The marked ball wear tests showed that the wear rate could be minimized by a suitable combination of martensite and ferrite within the same ball. A ball composed solely of hard martensite exhibited increased wear under an oxygen environment, while balls composed of both soft ferrite together with hard martensite exhibited decreased wear due presumably to the difference in their passivation behaviors. The galvanic interaction between the two phases as well as among these phases and an electroactive mineral were investigated through electrochemical measurements under abrasive condition in a slurry. The rates of formation of passive film controlled the corrosion currents of the high chromium steel media. Corrosive wear and its effect on flotation are discussed using the passivation kinetics model thereby developed.

Jan 1, 1990

By Y. H. Chia, P. Somasundaran

Carrier flotation of anatase from clay using coarse calcite is investigated, together with relevant basic properties of the system including aggregation and zeta potential, under different chemical and hydrodynamic conditions The roles of carrier sue and amount also are considered Mechanisms responsible for selective aggregation and flotation are reviewed

Jan 1, 1983

By Dae S. Young, Steven F. Hoerger

The geostatistical method of indicator kriging (IK) was extended to analyze two-dimensional distributions of rock joint orientations. The IK method provides a non-parametric approach for spatial analysis of local probability distribu- tions. By taking into account the spatial correlation of rock joint outcomes and the relative geometry between estimation unit and samples, the IK method provides optimum, spatially conditioned estimates. The estimation method was tested by comparing distributions of actual mapped rock joint orientations with their corresponding kriged estimates. The comparisons show the unbiasedness and accuracy of the non-parametric approach for estimating local probability distributions.

Jan 1, 1986

By S. K. Mukherjee, M. M. Singh, N. I. Jayaramn

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years, there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper recommends guidelines for water spray systems to control dust in underground mining operations. These guidelines suggest type, number, location, and orientation of nozzles; desirable operating water pressure; and associated filtration system.

Jan 1, 1987

By Lawrence F. Rooney

The wide distribution of limestone and dolomite and the decentralization of the depedent industries give the State Geological Survey a major role in the, development of these mineral resources. The amount of geological information necessary for efficient exploration is so large that few companies can afford to do the necessary basic field work or store the data. The state surveys fill these responsibilities and thus might be said to serve as the geological research departments of the limestone and dolomite industry. At the Indiana Geological Survey, the data of most value to limestone producers are in the form of unpublished measured sections, well records, cores, chemical analyses, directories, and geologic maps. Much of this information is published in summary form. The Survey also assists individual members of industry in exploration and evaluation of mineral deposits. In addition, a progressive State Survey provides the geological infor¬mation necessary for the development of new resources which do not appear to justify industry's own preliminary efforts.

Jan 1, 1966

By M. J. Virnig, C. P. J. Van Vuuren, A. J. Botha

The Zadra, AARL and organic elution processes and variations of them are presently widely used to recover gold from activated carbon. Despite this the study of the kinetics of elution have received relatively little attention. It is the aim of this study to investigate the rate processes taking place during elution in both inorganic and organic solutions. Batch adsorption and elution rate and equilibrium experiments were performed. The spatial concentration of gold inside carbon particles at various stages of the adsorption and elution processes were measured with a scanning electron microscope using an image analyzer to control and manage the micro-analysis data. The activated carbon particles exhibited film and intra-particle mass transfer rate- controlled behaviour during adsorption in a caustic aqueous solution at 95°C. Elutions in the aqueous caustic acetone solution at 30°C and the caustic aqueous solution at 95°C were unaffected by change in stirring rate. Elution was modelled by desorption reaction rate-control at the outer surface of the carbon particle. Adsorption and elution isotherms under duplicated solution conditions showed reasonable agreement for the inorganic solution and a large disparity for the organic solution.

Jan 1, 1993