Search Documents

By J. S. Murty

In this paper, a report is given of studies undertaken in a laboratory rod mill to obtain the optimum conditions for the desired particle size distribution for long-distance transportation of coal through slurry pipelines.

Jan 1, 1987

By J. Gallegos, R. Faber, T. Cox

"An innovative method to reduce acid rock drainage (ARD) and sediment loading of a recreational lake was used in the Red River watershed in northern New Mexico. The Red River drains a mining district that contains multiple naturally occurring hydrothermal alteration zones that release ARD and sediment to the river during episodic summer rain storms. A lake is near the mouth of the watershed and is filled with water from the river through a sluice gate and diversion. An automated actuator was installed on the sluice gate to close when the river is impacted by high-suspended sediment. Water quality probes were installed at the sluice gate to monitor the river water for turbidity, specific conductivity and water depth. If high turbidity is measured, the sluice gate closes automatically. Remote access is setup with a computer view screen to review the real-time system status. Once the turbidity drops below a threshold, the sluice gate is reopened remotely. The automated sluice gate has successfully reduced the amount of ARD and suspended sediment entering the lake. This reduction has resulted in an improved aquatic habitat for the fishery and benthic macroinvertebrate community. BACKGROUND The Red River is located within the Sangre De Cristo Mountain Range in northern New Mexico. The river drains an area of approximately 190 square miles and spans elevations from 6,600 feet at its confluence with the Rio Grande to its headwaters near 12,000 feet (Figure 1). The river generally flows to the west along most if its length.The Red River watershed includes several hydrothermal alteration zones. The alteration zones were created by intrusion of high-silica granites and subvolcanic porphyries, with associated hydrothermal fluids, into the volcanic rocks of the Questa Caldera. The hydrothermal alteration is also responsible for the molybdenum deposits in the area. Rapid chemical weathering and physical erosion of pyrite-rich hydrothermally altered rocks has resulted in the formation of alteration scars. The alteration scars are characterized by steep, erodible slopes with little vegetation and incised gullies. Debris fans from the drainages containing active alteration scars have formed and typically consist of poorly sorted sand and gravel that is distinctly pale yellow in color. Some of the more prominent scars are located in the Hansen, Straight and Hottentot Creek drainages downstream of the town of Red River."

Jan 1, 2018

By R. L. Garrett

The quality of mineral additives used in a drilling fluid (mud) can dramatically affect the fluid's properties and the overall cost of drilling an oil or gas well. The principally wed minerals are bentonite, barite, barite/hematite blends, and hematite alone. The high specific gravity minerals, barite and hematite, are used to increase drilling fluid density. Bentonite clay is used to increase drilling fluid viscosity and gel strength and to provide a low permeability filter cake. A multimillion dollar investment in a well and the safety of the personnel on the drilling rig can depend on how effectively these mud additives perform with other constituents in the mud. This paper points out effects caused by small amounts of certain carbonate and sulfide mineral impurities in barite or hematite and how polymeric extender additives in bentonites contribute to unpredictable behavior of a mud. Effects like these are the reason oil companies using these materials sometimes set their own quality standards beyond those already specified in APZ Spec. 13A. Also discussed in this paper are the current standardization activities of API Committee 13 on these minerals.

Jan 1, 1988

By Jr. Pickering

Commercial quality kaolin deposits occur in fluvial sediments in both central-eastern Georgia and in the eastern Amazon River area of Brazil. Distinctive coarse and fine particle size kaolin deposits are present in both areas; they have many remarkable similarities for mineral deposits occurring at such wide geographic separation. Industrial, mineralogical, crystalline, and chemical resemblance of the coarse and fine kaolin deposits from the two areas will be described in detail. Knowledge of similarities of the Brazilian clays to those which have dominated world production in Georgia will help to develop superior quality kaolin products for world use in paper, paint, plastic, ceramic, and other applications.

Jan 1, 1997

By Stephen J. Reynolds

Arizona's geologic history is complex, resulting in a diversity of rock types and earth materials, including those of commercial interest. Regional variations in geologic history gave rise to three geologic provinces and an inequitable distribution of both metallic and nonmetallic mineral wealth. The Colorado Plateau is largely composed of flat-lying Paleozoic and Mesozoic sedimentary rocks and late Cenozoic volcanic fields and sedimentary deposits. Associated resources include gypsum, halite, sylvite, clays, specialty sand, flagstone, volcanic products, and aggregate. The adjacent Transition Zone features a large expanse of Proterozoic rocks, economically important Devonian and Mississippian carbonate rocks, and Tertiary volcanic and sedimentary materials. Nonmetallic resources in this province include facing and dimension stone, aggregate, decomposed granite, chrysotile asbestos, gypsum, clay, barite, fluorspar, zeolites, and limestone used for lime, cement, and railroad ballast. The Basin and Range Province has the most complex geologic history and, therefore, the most diverse assemblage of industrial mineral occurrences. These include halite, gypsum, clay, aggregate, decomposed granite, diatomite, zeolites, perlite, pumice, kyanite, limestone, marble, stone, and others. In addition, young stream deposits yield vast quantities of sand and gravel, Arizona's most economically important nonmetallic mineral commodity.

Jan 1, 1987

By Steven W. Hunt, Phillip U. Santacroce, Roger C. Ilsley

Consolidation grouting from the surface prior to mining a shaft is commonly performed to reduce groundwater inflows to a manageable rate. This paper describes the inflow reductions obtained within dolomite and limestone formations at several shafts and chambers due to grouting programs for the Milwaukee Water Pollution Abatement Program. The resulting inflow reduction factors are compared to results reported in the literature for other projects. Post-grouting pump tests are also evaluated as an aid in grouting assessment. Important considerations for estimating shaft inflows from pump test results are discussed. These considerations include loss of grouted mass during mining and influence of blasting and rock features on grouting effectiveness. This information should be helpful to design engineers and contractors who need to estimate inflows after pre-excavation consolidation grouting has been performed.

Jan 1, 1993

By Louis A. Sandbak

Drift excavation by boom-type roadheaders in the San Manuel and Kalamazoo sulfide copper ore bodies has been successfully demonstrated. Geomechanical rock classification in conjunction with detailed geologic mapping has been necessary to assess roadheader performance, and to predict advance rates in the varied rock classes in the San Manuel block caving mine. Rapid excavation and less fractured ground are obvious advantages of roadheader drift excavation over conventional drill and blast techniques. The geomechanical system of Engineers International (1984) can be an effective roadheader performance and ground support tool.

Jan 1, 1985

By R. E. Greuer

The design of mine fire emergency plans requires that the contamination of mines by fumes, and the mutual interaction of fires and ventilation systems be pre-calculated. Several computer models were developed by the Bureau of Mines for this purpose during the last decade. The models advanced in sophistication from the transient-state simulation of fume concentrations for the early stages of a fire to the steady-state simulation of airflow rates, concentrations, and temperatures for fully developed fires, and finally to the complete transient-state simulation of fires and ventilation systems. The principal features of these models are described.

Jan 1, 1989

By John W. Robertson, Edwin A. Zink, Gerald P. Zink, John E. Wolgamott

Equipment which will reliably produce high velocity water jets for use in rock excavation is now available. This report reviews some cases where water jets were used in excavating low to medium strength sandstone in Colorado and Utah. The primary discussion is of water jet assisted rotary drilling for blast and bolt holes in tunnels, shafts, and chambers. The subjects include drilling performance, effects on work environment, safety, and controlled blasting results. Information is also presented concerning trench excavation utilizing water jets.

Jan 1, 1983

By Paul E. Senseny

Data from triaxial compression tests per- formed at confining pressures between 0 and 100 MPa are used to evaluate parameters in a contitutive model that is based on microcracking. The tensorial formulation is reduced to equations that are specific to the simple Loading imposed in triaxial compression tests. Procedures for evaluating the model parameters are described, dependence of parameter values on confining pressure is discussed, and prediction of failure is assessed.

Jan 1, 1986

By V. O. Tenorio, K. W. B. Requist

As the mining industry begins efforts to examine the feasibility of extraterrestrial resource utilization, the extraction and processing of icy regolith containing water and other volatile materials will be the initial focus for future expansion of capabilities. Pure water is essential for human consumption, and a source of oxygen and hydrogen. The latter, along with the volatile materials, lend themselves to the creation of fuels that may be used for further space exploration at distances not currently feasible. For any extraterrestrial scoping project, the transport of materials to geoscientists remains virtually impossible. Therefore, analysis must be done in-situ, possibly millions of miles away from the nearest human. To address the need for geologic resource estimation in the absence of geoscientists, an infrared framework has been developed for the analysis of water ice content in simulants of permanently shaded lunar regolith. This framework relies on a convolutional neural network model for the rapid analysis of percent water ice content in samples, at which point standard geostatistical methods may be employed.

Feb 1, 2023

By Isiah M. Warner, Philip Oldham, John Kennedy, Bennett D. Lass

A new method for determination of residual flotation oils on beneficiated kaolin clays has been developed The method, which yields qualitative information, is based on fluorescence measurements employing a spatially resolved, polychromatic illumination source for excitation, and a two-dimensional detection scheme using a silicon-intensified, video imaging device The method was used to identify residual oils on a beneficiated, Washington County, Georgia, crude clay The results were compared to a similar qualitative analysis performed via capillary column gas chromatography using a flame ionization detector The video fluorometry was the preferred method of analysis

Jan 1, 1983

By M. S. Celik, G. Onal, S. Atak

The beneficiation of boron minerals flotation with well defined systems has been only slightly, investigated in the literature. The difficulty arises from fact that boron minerals cover a spectrum of solubilities. Colemanite (a calcium-containing, relatively insoluble, boron mineral) and borax (a highly soluble boron mine, have been used to exemplify the flotation of boron minerals. Using sodium dodecylsulfonate (SDS) and dodecylamine hydrochloride (DAH), the floatability responses of these boron minerals are considerably different. This has been ascribed to variations in the solubilities of boron minerals and the presence of cations in the lattice structure. In study, flotation tests and zeta potential measurements used to determine the flotation mechanisms of boron minerals.

Jan 1, 1994

By V. J. Matta, A. A. Pincheira, I. A. Reghezza, Ch. J. Vergara

The growth of solvent extraction in Chile has been astonishing during the last years and has been established as a very successful technology. However, there are still limitations that must be improved, mainly, the problem of carry over from one phase to the other and the losses of organic reagent associated with the crud formation. These are problems that our company has been taking care, solving them with high efficiency and low costs, allowing important increases in the copper output of our plants and capital savings by means of the optimization of the use of nonproductive units in the SX plants.

Jan 1, 1998

By Steven G. Vick, Herbert H. Einstein

1. INTRODUCTION The Tunnel Cost Model (TCM) is a computer based model whose objective is to quantify the risks of hard rock tunneling in terms of cost and time to completion. The main feature of the TCM is the simulation of the tunnel construction. The simulation makes it possible to incorporate in the time and cost computations the effect of uncertainties in geologic conditions and in productivity rates and costs. The cost and time computed with the TCM will be in form of distributions that allow a quantitative risk assessment. The TCM will be useful as an estimating tool permitting the estimator to rigorously relate uncertainties of individual factors to the end result. The TCM will also make it possible to evaluate technological innovations and to identify problem areas in existing technologies. The TCM consists of three interacting submodels: the geologic submodel, the construction operations submodel and the tunnel simulator. The goal of this paper is to describe the geologic submodel, whereas the construction operations submodel and the tunnel simulator will be described in the following paper by Moavenzadeh et al. First it will be shown how interactions between the geologic submodel and other parts of the TCM will impose certain requirements on the geologic submodel. These requirements, which relate primarily to the description of geologic conditions by a set of problem-oriented parameters and the quantification of uncertainty associated with geologic conditions, will then be discussed. This is followed by the description of the special structuring techniques -- decision tree and segmentation -- that are necessary to handle the great number of

Jan 1, 1974

By L. Diels

About 45% of the contaminated sites are dealing with heavy metal problems. Metals are spread in the environment by mining activities, surface treatment and non ferrous processing. As heavy metals can not be degraded, removal or immobilization (leading to bioavailability reduction) are the only risk reducing measures that exist. The currently best available technique for remediation of heavy metal contaminated groundwater is to pump the contaminated water and to treat it in a wastewater treatment plant installed on the surface. Next to this often used, but expensive, pump and treat technologies, heavy metals can be immobilized by inducing sulfate reducing bacteria (SRB) to transform the sulfates, that are very often present in the same groundwater (due to the metal mining or processing activities), into sulfides. These sulfides will precipitate the metals as insoluble metal sulfides. At the moment several studies have demonstrated the feasibility of this In Situ Bioprecipitation Process (ISBP) for the removal of heavy metals from ground-water as well at lab scale (batch and column tests) as at field scale. However, some questions arise concerning the continuation of the process, the efficiency and the sustainability of the precipitates. The presented study will try to answer these questions. The study is based on more than 10 different studies, all done by the same authors, on different groundwaters and aquifer samples. The presentation will give an overview of the guidelines necessary for a correct and successful bioprecipitation process with stable metal sulfide precipitates. An important question in the ISBP is related to the sustainability of the heavy metal precipitates. It could be observed that the interruption in the carbon source delivery also stopped the in situ bioprecipitation process. Depending on the metal also some release from the precipitate could be observed. It was shown that release can occur with Co and Ni. Aquifers, on which the metals precipitated during the ISBP, were treated in a sequential extraction process under an-aerobic and aerobic conditions. It could be shown that especially under the anaerobic conditions the Zn and Cd precipitates changed from the leachable and the exchangeable fraction to the organic or Fe-Mn fraction (i.e. from the unstable to the stable fraction). The same could be observed for Co and Ni but still some fraction was present under a more available form. On the other hand it could be shown that large differences were observed concerning the heavy metal speciation on the aquifer in function of the used carbon source during the ISBP. The molasses treated systems showed a much more available heavy metal fraction on the aquifer compared to the lactate or HRC® treated groundwater. The different speciation forms based on the use of different carbon sources will be discussed in detail. It will pay attention to the influence of the carbon source, the efficiency of the induction of the bioprecipitation process, the influence on the competence between sulfate reducers and methanogenic bacteria and the influence of low pH on the ISBP. It seems that acetate, which is also a degradation product of fermentation of some carbon sources, can inhibit some sulfate reducers. Also the relation between slow release compounds and immediately available compounds will be explained. Finally a pilot study will be presented showing the problems that can be encountered during this process. Focus will be put on the induction of the process, the keeping on of the process and the follow up of the process by the installation of in situ mesocosm socks. These results will allow the correct implementation of the ISBP with an eye on longevity and sustainability of the process and present the ISBP as a much more sustainable alternative to the pump and treat technology as measure for heavy metals contaminated groundwaters.

Jan 1, 2006

By N. I. Jayaraman

Dust scrubbers on continuous miners are steadily gaining in popularity. Recent Bureau of Mines research on scrubbers is reviewed, with emphasis on the following areas: * Development of a new type of water-powered scrubber which can be retrofitted to existing miners. * Comparison of scrubber effectiveness with blowing and exhaust line ventilation. * Improving the quartz dust collection of flooded-bed' panels.

Jan 1, 1989

By Peter K. Weissenborn, Robert J. Pugh

The contrasting behaviour of electrolytes in inhibiting coalescence of bubbles was explained by the positive and negative distribution of anions and cations at the gadwater interface. Further, the efficiency of electrolytes which do inhibit coalescence of gas bubbles can be linked to a counter ion hydration mechanism and the effect of electrolyte concentration on gas solubility. A correlation was found between the transition concentration of electrolyte needed to prevent the coalescence of bubbles and the reduction in gas solubility. Hence, the inhibition of bubble coalescence in electrolyte solutions appears to be linked with the utilization of water molecules in the hydration of cations and a consequent reduction of water available for gas solubility.

Jan 1, 1995

By J. C. Yingling, R. Kumar, J. Sottile

The capability for on-line measurement of the quality characteristics of conveyed coal now enables mine operators to take advantage of the inherent heterogeneity of those streams and split them into wash and no-wash stocks. Relative to processing the entire stream, this reduces the amount of coal that must be washed at the mine and, thereby reducing processing costs, recovery losses and refuse-genera¬tion levels. In this paper, new ap¬proaches for optimal control of the segregation process using time-se¬ries models and empirical distribu¬tions are presented and demon¬strated using field data.

Jan 1, 2000

By S. N. Mukherjee

Maintenance of equipment in Longwall faces plays a vital role in face performance. This is more prominent when shortage of spare parts and trained personnel occurs. A study was made in an operating Indian Longwall face for identifying the types and meantime between failures. Though the duration was not enough and study was not very elaborate, it revealed certain interesting facts. The machine availability was found to be poor, though a maintenance schedule was followed. Failure of simple parts like AFC chain connectors even resulted in loss of production of 10 times the complete chain cost. This pinpoints that a proper maintenance schedule is to be developed considering the human factors and local conditions existing in the particular country. Operations research techniques could be used in the process.

Jan 1, 1989