Search Documents

By Morgan M. Sears

The LaModel program is widely used to calculate stresses and displacements on thin tabular deposits, particularly when multiple seams or complex mining geometry is encountered. The program itself allows the user to create multiple mining steps to show a progressive sequence of mining. However, LaModel considers each individual step as an independent steady-state condition, and any previous loading conditions of the materials are not tracked. It also does not consider any sort of dynamic stress change during the mining process. In certain circumstances, especially in multiple-seam situations, modeling a scenario of the seam of interest without considering the previous mining sequence in the off seams can potentially lead to inaccurate results. The primary objective of this paper is to present a situation where a potentially dynamic, unstable mining condition was encountered. It was not evident until the previous loading conditions in the off seams and the impact of dynamic stress changes in the active seam were considered. It is important to make the mining community aware of these potential modeling scenarios where the path-dependent nature of the mining sequence is of key importance. This paper presents a case history where room-and-pillar retreat mining was being conducted in a relatively deep cover stress regime where multiple seam interactions were present from both undermining and overmining. Mining in the active seam was being conducted with roomand- pillar mining techniques consisting of a series of parallel production panels being successively developed and retreat mined along a set of Mains. In this situation, the traditional global LaModel analysis without any path-dependent adjustments did not fully identify the area of poor conditions that were encountered. This paper explores the impacts of mining in the active seam on the lower seam which, in turn, has a negative impact on the active seam. This provided a solid foundation for the subsequent analysis of the three seams simultaneously. Based on the calibrated model, it is likely that retreat mining in the active seam resulted in increased stresses in the underlying seam that conceivably resulted in additional convergence and, most likely, additionally convergence of the pillars under the panel being developed. This in turn could have caused active subsid- The LaModel program is extremely useful for analyzing multiple-seam mining scenarios. As multiple-seam situations become even more prevalent, the potential for encountering a path-dependent mining scenario also increases. To successfully model path-dependent mining scenarios, the ground control engineer will be required to make sound judgments on the condition of pillars in sub-adjacent seams. These engineering judgments should be based not only on the current state of stress, but also on any prior or future states of stress. This means considering the stresses from over or undermining as well as stresses applied to the sub-adjacent seams from actively mining the seam of interest.

Jun 25, 2024

By Pramod C. Thakur

Tunnels are defined as underground passages made without removing the overlying materials. From time immemorial men have driven tunnels for mining purposes. Even today tunnels are the building blocks for underground mines. The total length of such a network of tunnels in a mine may add up to 10-100 miles! In addition to this, rapid development of vehicular traffic, needs for air raid protection and metropolitan traffic problems have given a great impetus to underground tunnel construction. But for the successful drivage of any tunnel an adequate air environment has always been and remains an essential prerequisite. This is particularly true for tunnels in mines which are driven in gas bearing strata often at a substantial depth from the surface. An adequate air environment is designed to promote the health, safety and comfort of workers which results in greater productivity and efficiency. Its legal definition varies from country to country but, in general, it means the provision of sufficient circulating air, often at specified velocities, to maintain: (i) at least 19% oxygen in the working areas (ii) Concentration of pollutants, e.g., methane, carbon monoxide, respirable dust, etc. below specified limits. Table 1 shows the maximum allowable concentrations for some of these pollutants.1 (iii) Temperature and relative humidity below specified limits. Ventilation of tunnels in mines assumes ever. greater importance today because of increased mechanization and concentration of output which leads to higher rate of production of inflammable gases and respirable dust. Efficient management of the tunnel air environment, however, depends heavily on a thorough knowledge of how

Jan 1, 1974

By Steve Kral

The Red Dog zinc-lead deposit, said to be the world's second largest, is located inside the Arctic Circle in northwestern Alaska - a location too harsh and remote for some mining companies but just right for Cominco Ltd. The complex has been in operation since November 1989 and is producing 508 kt/a (560,000 stpy) of zinc concentrate, 109 kt/a (120,000 stpy) of leadconcentrate and 45 kt/a (50,000 stpy) of an Imperial Smelter Feed, a combined zinc-lead mixture that is too small to separate. All of this concentrate production derives from a relatively modest mine production of 5.4 kt/ad (6000 stpd) extracted from a surface pit. Despite being a high-grade zinc-lead deposit, Red Dog's metallurgy is complex, requiring a very fine grind and use of column cells for flotation. The Red Dog complex is located in the DeLong Mountains. They are characterized by eight stack and folded thrust blocks that contain sedimentary and igneous rocks. The Red Dog deposit is located in the second lowest thrust and ist hosted by late Mississippian to Permian age black shale, the Ikalukrok member of the Kuna formation. The Red Dog mining complex is operated by Cominco Alaska, Inc., a wholly owned subsidiary of Cominco American, Inc, which, in turn, is owned by Cominco Ltd. In 1980, the deposit region was acquired by NANA Corp. as part of the Native American Claims Act Settlement of 1971. NANA is one of 12 such Native Corporations in Alaska. In 1982, NANA and Cominco American signed a develop¬ment agreement and formed Cominco Alaska to manage the project.

Jan 1, 1992

By S. Barkhoudarian, R. R. Gupta, R. F. Steinberg

A study of the feasibility of using acoustic signals to detect discontinuities ahead of excavation has shown that reflecting interfaces in a homogeneous rock can be easily identified. Moreover, discontinuity interfaces in a very complex field site (where the rock face was weathered, was full of jointed rocks, and had a destressed zone running along the mine walls) could be identified with a reasonable level of confidence, using a cross-correlation technique for signal processing. The results of this study go a long way toward proving the feasibility of the technique. However, further development work is needed to optimize an operating system in a hard rock environment where boring machines are used for excavation.

Jan 1, 1997

By S. D. Thompson, J. C. Dzurino

This investigation mainly focused on designing a bunker system for a large underground coal mine. The primary purpose of this bunker system was to keep high- and low-sulfur coal segregated on the underground belt system. These bunkers were also required for protecting the mine faces from out by belt delays. Methodologies used in developing this plan are briefly discussed. The final design and the procedures formulated for implementing it are also presented.

Jan 1, 1987

By D. R. Schmitt, B. L. Jensen, T. J. Ahrens, C. L. Smither

The in situ elastic moduli of rock are measured holographically by a borehole instrument in marble and oil shale. A point force induced displacement field is recorded with double expo- sure holography. Data consists of a fringe pat- tern on the viewed hologram. The elastic moduli are determined by modelling of the fringe pattern. Only Young's inodulus is fairly constrained by the present data reduction. For an applied force of 520 [ ] 50 Newtons, a marble was found to have a Young's modulus of 56 [ ] 8 GPa, near an ultrasonically determined value of 48 [ ] 6 GPa. In an oil shale, an applied force of [ ]

Jan 1, 1986

By Joe W. Cotton, Thomas A. Wheeler

This paper briefly covers theories behind caking of crystalline salt particles, and methods of its prevention. The main factors that influence the extent of caking are humidity, storage pressure, temperature variations, and length of storage time. Careful adherence to control- ling these variables are more critical than the addition of even the most efficient anticaking reagent. The principle characteristics that a successful anticaking reagent must possess are: high retention at the temperature of application, good coating of reagent on the particle surface, capability of in- creasing the hydrophobicity of the particle, reducing the surface tension of liquids, and/or creating of a barrier between particles that prevent contact between particles, and modifying the crystal structure of the salt between the particles. Methods to evaluate the reduction of caking tenacity with the application of various anticaking reagents, reagent volatility and reagent degradation in plant and laboratory scales are discussed. Various types of anticake reagents used today in industry are organic active and inactive reagents, inorganic inert and inorganic salt crystal modifying re- agents.

Jan 1, 1986

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH's Pittsburgh Re¬search Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, which are tightly wrapped with many turns and which carry current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften, making them prone to damage. The damaged insulation reduces the life of the cable and can lead to shock, electrocution and mine fires. This paper describes a method of measuring the conductor tem¬perature of mine trailing cables during normal operation. The temperature is measured using a 50/125-, µm graded index multimode optical fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an optical time domain reflectometer (OTDR). This system is capable of measuring temperatures with an accuracy of ± I °C over a length of 4 km at I -mintervals. With this unique way of measuring temperature, tests can be conducted that simulate actual mine conditions. The tests provide important data that allows MSHA's Approval and Certification Center to develop approval criteria for cycli-

Jan 1, 2000

By A. C. Noble

Ore reserves are often less than 30% of the geologic resource estimates initially prepared by exploration geologists. Differences of this magnitude can lead to serious problems in the early valuation of properties when the geologic resource estimates are interpreted to represent ore reserves but are later found to be misleading and gross overstatements of the actual ore tonnages. The geologist can avoid such difficulties by considering the implications of mining, metallurgical recovery and economics early in the project and by using appropriate qualifiers in the resource statement. Examples using typical deposit characteristics are used to demonstrate how the cutoff grade, stripping ratio, dilution, mining extraction and metallurgical recovery affect ore reserve estimations.

Jan 1, 1994

By Irwin R. Higgins, Joseph C. Milbourne

The selection of a suitable nitrate removal process depends on a variety of site-specific chemical and environmental issues. The dominant technologies for nitrate removal include biological denitrification and continuous countercurrent ion exchange. The decision to apply either of these technologies, or both together, depends on the nature of the waste water to be treated. Factors that affect the selection of the biological system include the feed composition and feed temperature. Ion exchange nitrate removal systems ere less sensitive to the feed composition but require disposal or destruction of the concentrated pregnant eluate. The paper discusses Tetra's continuous countercurrent ion exchange technology (CCIX™) and fixed film biological reactor, Denite®. The treatment of the ion exchange pregnant eluant is also discussed.

Jan 1, 1995

By R. H. King

Mine managers need better information to locate new opportunities and then to assess the effect of their decisions. We are developing the Intelligent Decision Support System (IDSS) and its two major modules, the Pattern Recognition System (PRS) and the Knowledge Representation Subsystem (KRS) to automatically provide the information from monitoring system sensors. So far, we have developed and reported on algorithms that automatically produce accurate time-study reports of continuous miner data from kilowatt sensors at the Deserado Mine, and we are extending the system to accept other types of sensor data input. This paper focuses on AI techniques that improve accuracy of the numerical algorithms in the PRS module. Additional AI work for the KRS module is summarized in this paper.

Jan 1, 1989

By J. D. Miller, C. L. Lin

The appropriate software and hardware necessary to adapt an X-ray CT analyzer for the determination of coal washability was developed and successfully tested for well-characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed X-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically, the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined. Key words: Coal washability, Computer simulation, X-ray CT analysis

Jan 1, 2003

By G. A. Dawe, E. G. Kelly

Because of the nature of the breakage in the Barmac vertical spindle impactor, the 80% reduction ratio is very small, so that when an energy efficiency is calculated from Bond's method, it appears to be very low. However, the product size distribution contains a high proportion of fines. It is argued that the production of these fines accounts for the high energy consumption, and Bond's method is modified to account for this, by considering the crusher to be, effectively, a number of smaller crushers in parallel, each having a different reduction ratio.

Jan 1, 1990

By David M. Miller, Pramod C. Thakur, Larry D. Taylor

The most common technique used to suppress respirable coal dust in air is that of spraying with fine water particles. The water droplets are typically much larger than respirable dust particles and they collect dust particles mainly by interception. Dust collection efficiencies can be improved by reducing the droplet size and in- creasing the droplet velocity. This is typically done by reducing the surface tension of water and increasing the water pressure. Dust collection efficiency can be further improved by in- creasing the electrical attraction between the water and dust particles through electrostatic charging. A technique developed by Conoco accomplishes both surface tension reduction and electrostatic charging by discharging weak solutions of surfactants in water at high pressures, 13.8 to 27.6 MPa (2000 to 4000 psi) in an intrinsically safe manner. The paper de- scribes the process and presents related dust suppression data.

Jan 1, 1986

By F. Leschhorn

A computer model for long-term production scheduling is presented. By combination of different operations research algorithms it has been possible to design a system which is able to solve difficult long-term planning problems. The practical application of the model by a west-german hard coal mine is shown. It is proven that the EDP-model provides substantial support to the planning engineer by solving complex optimization problems.

Jan 1, 1989

By Gerald L. Tiley

When payloads and hoisting distances are beyond the capacity of a single headrope, a multi-rope hoist will cost less than, and require less maintenance than, several hoists with one headrope per conveyance. This paper describes the basic type of multi-rope drum and friction hoists in use today, the types of ropes available, and the essentials of a satisfactory installation.

Jan 1, 1981

By Frederick H. Parkinson, Joseph Fernandez, David E. Westfall

The April 13, 1992, flooding in the freight tunnel network under the city of Chicago had a profound effect on the nearby Chicago Transit Authority (CTA) subway service. This paper provides an overview of the evaluation techniques, mitigation measures, and water control efforts used to maintain the integrity of the subway tubes. Specific topics discussed include visual inspections, inflow monitoring, structure and soil testing and sampling techniques, and the development and implementation of chemical and cementitious grouting programs.

Jan 1, 1993

By Lijun Xu, Jan M. Mutmansky

The purpose of this research was to investigate airborne coal mine dust characteristics in order to assess the possibility of contribution of these characteristics to the incidence of coal workers' pneumoconiosis (CWP). The characteristics studied included physical (mass concentration and size distribution), chemical (elemental composition), and mineralogical (quartz and kaolinite content) variables of the dust. The results are based primarily upon analysis of the characteristics of 99 impactor samples from 18 mines in seven states. Because the eight stages of the impactor span the range of dust sizes up to 20 microns, the characteristics analyzed should represent respirable dust characteristics well and also provide size-dependent representations of the characteristics. In general, the patterns of mass concentration and size distribution in the various mines studied were similar with mass concentrations being high downwind of the continuous miner. The concentrations and size distributions were more variable upwind of the continuous miner, apparently as a result of the variations in the dust conditions in the working section. Significant size effects on the elemental and mineralogical content are shown in the data. Concentrations of most of the elements decrease as size decreases. However, minerals content increases as the dust size decreases. Regional variations of elemental and mineralogical content are also significant. Quartz and kaolinite contents are small in regions with low incidences of CWP. However, the elements of Cu and Zn are high by comparison to their content in high-incidence coal fields and may have the effect of protecting against the disease.

Jan 1, 1991

By V. B. Achanti

This paper deals with the effect of various bit geometric parameters on failure characteristics of rock material. Improvement of rock cutting efficiency of continuous mining machines has been an interesting research topic for the last few decades. In the current study, an automated rotary rock cutting simulator, duplicating a continuous miner, was utilized to study these parameters in the laboratory. Improvement of bit performance in terms of its life, cutting efficiency, dust production and energy consumption has drawn wide spread attention over the years. Research shows that optimizing bit parameters can result in efficient fragmentation of rock. Indiana limestone rock material was utilized in this study while bit tip angle, bit tip size, bit spacing, depth of cut and cutting velocity of rotary drum were varied to investigate the failure characteristics. The cutting pressure, penetrating pressure and the depth of cut were monitored on the simulator during the cutting process. Air borne dust and settled dust were measured for each experiment. Then, the specific airborne dust and specific energy were determined for the each type of bit. Triaxial tests were carried out to correlate the failure angle of the rock in static case to dynamic cutting process failure. The physical and mechanical properties of the rock were also determined in order to assess their influence on the wear characteristics of each bit.

Jan 1, 1998

By Usko Anttikoski

This article deals with the extensive geotechnical soil and bedrock mapping system maintained in the Geotechnical Office of the City of Helsinki since 1955.Soil maps have been prepared to scales of 1:500,1:2000 and 1:10 000, and most recently in 1978 a new type of bedrock map was printed to a scale of 1:10 000, which covers the whole city area and particularly serves rock tunnel construction. A map showing the types of foundation building in the central city area, which will also serve underground construction activities, is currently being prepared. Since the geotechnical mapping system has been well received in Helsinki and the drawing of similar maps has also been undertaken in other Finnish towns, this mapping method is believed to be of interest to foundation engineers and tunnel constructors elsewhere too. THE GEOTECHNICAL CONDITIONS IN HELSINKI The geological structure of Helsinki, and of all Finland, presents two types clearly differing in character and age; bedrock and soil. The solid bedrock is Precambrian, while the soil dates from the Pleistocene Age and has mainly been deposited during and after the Ice Age. Thus the history of Helsinki only displays very old and very young formations, but nothing in between. The ground level in Helsinki is +62 at its highest and the sea bottom close to shore is -15 at its deepest. The deepest rockhead has been found to lie at the -70 level.

Jan 1, 1979