Search Documents

By J. K. Whyatt

This report describes a microcomputer-based instrumentation system for structural monitoring of the circular, concrete-lined Silver Shaft in northern Idaho, The 1-ft-thick concrete lining and surrounding rock mass were instrumented with a total of 12 multiple-point borehole extensometers, 16 pressure cells, 22 concrete embedment strain gauges, and 12 thermistors. The instruments were distributed among four test sites and installed immediately above the shaft bottom during sinking at the 2,414, 4,063, 5,191, and 5,955 levels. Limited access to the instruments prompted the development of a microcomputer-based remote data acquisition system that could be operated from the surface. The system scanned the instruments on a programmed schedule, printed out reduced data, and stored the data for plotting and recall. Data acquisition from off-site and uploading of data to mainframe computers were accomplished by the addition of modems to the basic system. The system is suitable for use in monitoring the structural behavior of any deep mine opening, especially in harsh operating environments and where access is limited.

Jan 1, 1986

By Hugh D. Pallister

Alabama probably has the most extensive deposits of high-grade flake graphite in the United States and was the largest producer during World War I. Therefore, with the outbreak of World War II, users of flake graphite turned again to Alabama to supply their requirements. Flake graphite is the most important ingredient contained in graphite crucibles used in melting crucible steel and special alloys essential for war purposes. Early in World War II the Army and Navy placed flake graphite on the list of critical war materials. During World War I, when the supply of Ceylon graphite (then in demand) was cut off, large quantities of flake graphite were produced in Alabama, and about 40 mills were built. Most of these were abandoned after the war when imports of the cheaper Madagascar flake (which gradually replaced Ceylon graphite) began to reach this country. With the beginning of World War II, the Madagascar supply was cut off', and consumers were again compelled to look to domestic sources for their supplies. They found only one small mill in operation, that of the Ceylon Graphite Co. in Coosa County, Ala. The Bureau of Mines made a preliminary examination of the Alabama flake graphite deposits in 1940. Samples were taken and tested at the Southern Experiment Station at Tuscaloosa.

Jan 1, 1948

By G. Asai

The purpose of this Bureau of Mines investigation was to determine the properties of arc-melted iron-chromium alloys ranging in chromium content from 12 to 50 wt.-pct. Alloys were prepared by consumable-electrode arc melting of electrodes composed of high-purity chromium and high-purity iron. Alloys were fabricated to rod and sheet, and the following data were obtained: Electrical resistivity, hardness, tensile strength, and impact strength at room temperature; and creep-rupture life at 650° C. (1,200° F.). As the chromium content of the annealed alloys varied from 12 to 50 pct., the properties varied as follows: The electrical resistivity increased proportionally from 41 to 53 microhm-cm,; the Rockwell hardness varied from A 38 to A 58; the tensile strength ranged from 52,000 to 96,000 p.s.i.; the impact strength of V-notched charpy specimens varied from 140 to 405 ft.-lb., and the 100-hour creep rupture life at 1,200° F. varied from 5,000 to 16,000 p.s.i.

Jan 1, 1962

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known measured and indicated recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the eighth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Jefferson County, Pa., which comprises parts of Marienville, Hallton, Ridgway, Brookville, DuBois, Penfield, Smicksburg, and Punxsutawney quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals is included. Data on the coal beds in the county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information. A base map for each bed in each quadrangle was made to the scale 1 inch equals 1,200 feet. Maps of mines, locations of drill holes, bed and total coal thicknesses, and the outcrop of the bed were plotted on the maps. With all available data plotted, isopach lines were drawn to limit areas of known unmined reserves in beds 0 to 14 inches thick, 14 to 28 inches thick, 28 to 42 inches thick, and over 42 inches thick, These areas of coal reserves also were divided into "measured" and "indicated" categories. All areas in each thickness range and in each category, mined-out areas, areas excluded from the estimate, and areas outside of the outcrop were measured by planimeter on the base maps. Estimates of total reserves 14 inches and more thick and maps for individual beds were prepared from these data.

Jan 1, 1952

By J. F. Messerly

The purity of three specially prepared samples of benzene was determined with an adiabatic, low-temperature calorimeter with automatic control of shield temperature. Extensive measurements were made on each sample to determine how variations in operating procedures affect melting-point and freezing-point as well as purity data obtained by the calorimetric method. Detailed results of the investigations are presented, and effects of different operating procedures are discussed, together with problems encountered in interpretating experimental results.

Jan 1, 1963

By Glenn C. Reed

The Sheep Creek iron deposits, Meagher County, Mont., were investigated by the Bureau of Mines in 1943 and 1944. Work undertaken included exploratory trenching, churn drilling, petrographic studies, and detailed beneficiation tests. It was determined that the Sheep Creek ores occur both as fissure filling and bedding replacements in thin-bedded shale and arenaceous limestones of the Algonkian Belt series. At least five stratigraphic horizons were found to be mineralized. Metallurgical studies indicate that the ores are not amenable to beneficiation by present-day low-cost methods. Details of geology, sampling, and beneficiation tests are presented in this report.

Jan 1, 1949

By Charles W. Huggins

To determine the nahcolite and dawsonite content in oil shales, the Bureau of Mines compared X-ray diffraction, infrared spectroscopy, thermal methods, and a previously published method by Smith and Young based on the selective solubility of sodium compounds. The Smith and Young method and a new method based on the weight of carbon dioxide produced by thermal decomposition are recommended for determining nahcolite. X-ray diffraction and the Smith and Young method are recommended for determining dawsonite. X-ray diffraction, infrared spectroscopy, and differential thermal analysis were useful for identifying other minerals in the samples.

Jan 1, 1973

By L. Kaufman

A range of processing conditions and compositions have been evaluated in order to optimize the properties of TiB2-(Ni,Cu) composites for application as a non-sparking tool material for use in coal mining operations. Fifty billets containing from 70 to 9S weight percent titanium diboride were hot pressed at 3000 psi between 2400°F and 2650°F. Samples which were cut from these billets were used to measure hardness, bend strength and impact strength so that composition/processing optimization could be effected. Eight compositions selected on this basis were evaluated by incendivity tests in order to choose the best composition. The best results were obtained for an 85 w/o TiB2-12 w/o Cu-3 w/o Ni composite hot pressed at 2650°F and 3000 psi. This material appears to be the best choice for fabrication of coal cutter bits to be evaluated in field tests.

Jan 1, 1973

By R. L. Crosby

The Bureau of Mines investigated alloys of copper with 2, 3, and 4 vol pct alumina and with 2 vol pct yttria. Alloys were prepared by a coprecipitation process and were fabricated by pressing and sintering of powders, extrusion, and swaging. Tensile properties at room and elevated temperatures, stress-rupture strength, electrical conductivity, and density were measured. The superiority in elevated temperature strength of dispersion-strengthened copper to OFHC copper was confirmed. Increasing the oxide content from 2 to 4 vol pct produced only a small improvement in strength properties and decreased the electrical conductivity. The 3 vol pet alumina alloy had the best overall combination of properties.

Jan 1, 1969

By Maria I. De Rosa

The U. S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (~300° C) and later (~400° C) combustion stages of chlorinated polyester-reinforced mine ventilation ducts could be predicted by a smoke particle characteristic, for the development of a test parameter. The experiments were conducted in an approximately 20-L furnace, at 14-min durations at set furnace temperatures of 2500 and 1,000° C, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCI), carbon monoxide (CO), carbon dioxide (C02), and oxygen (02) concentrations, furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and average number and concentration (no), and the product of the average smoke particle diameter and concentration (dgno). Results show that the inverse of the smoke particle diameter-concentration product [(l/dgn0)], correlates directly and significantly with the primary gas toxicities evolved during both early (HCI) and later (CO) stages of combustion.

Jan 1, 1989

By J. I. Paige

The effect of fluoride inclusions on the properties of titanium produced from the Bureau of Mines developed induction slag melting process is of concern to members of the titanium industry. The objective of the research was to determine the effect of CaF2 inclusions on the properties of titanium and its survival rate during melting. The data were obtained from single induction-slag-melted ingots prepared with the normal addition of 4 pct and also with 2- and 1-pct additions of CaF2 slag. The results of this effort showed that the mechanical properties of single-induction-slag-melted Ti-6Al-4V alloy exceed the minimum values specified in Aerospace Materials Specification for Titanium Alloy Bars and Forgings AMS4928H, but these materials are much more notch sensitive in fatigue than normal Ti-6A1-4V alloy titanium. First and second vacuum-arc remelts of single-induction-slag-melted ingots fragmented and increased the number of inclusions, while reductions in the amount of flux resulted in an upward trend in the spatial distance between pores in an x-y plane.

Jan 1, 1988

By L. Allan White

Instrumental analysis is an indispensable tool to many phases of research on rare-earth metals and their compounds; therefore, the development of new and improved instrumental techniques is essential. This report describes an emission spectrometric analytical method using direct-current carbon-arc excitation of various rare-earth-oxide mixtures. Lanthanum oxide serves the dual purpose of an internal standard and a constant major constituent. The versatility of the method was demonstrated by three different applications: (a) Analysis of complex rare-earth concentrates; (b) determination of impurities in high-purity rare-earth oxides; and (c) detection of rare-earth elements in other types of matrices, such as those resulting from beneficiation of rare-earth ores. The average error of analysis in the concentration range of 0.2 to 10.0 percent was 14.6 percent for a group of complex synthetic mixtures of rare-earth oxides. An average error of analysis in the concentration range of 0.05 to 0.50 percent was 21 percent for a group of high-purity rare-earth oxides.

Jan 1, 1959

By William J. Campbell

These investigations were undertaken as part of a program to determine the optimum X-ray spectral lines to use for analyzing the wide variety of samples received by the X-ray Laboratory. Theoretical calculations and experimental data derived from these investigations show that longer wavelength spectral lines, > 2A, are very useful for many analytical problems. Because of the low fluorescence yield of the elements of atomic numbers 13-22 and the small depth of penetration of their X-ray spectral lines, these elements were originally considered to be insensitive; however, these studies show that the wide dispersion of their spectral lines, coupled with their weak beta lines, permits the use of wide collimation, thus increasing the line intensity. More importantly, the background due to scattered primary radiation is very low in the long-wavelength region.

Jan 1, 1959

By James R. Coldwell

Mining and processing cost analyses were conducted by the U.S. Bureau of Mines on massive sulfide copper-zinc and low sulfide vein gold deposit types that may be found in the Ketchikan Mining District. Reserves and recoverable metal values (RMV) needed to make these deposits economically viable were modeled. Methods for estimating ore grades and required RMV are presented. Economic modeling for massive sulfide deposits indicated the RMV necessary for a 15% Discounted Cash-Flow Rate-Of-Return (DCFROR) for an underground cut-and-fill mine ranged from $137/mt for a 6,100 mtpd on-site milling operation to $526/mt for a 450 mtpd off-site milling operation. On-site milling was always less costly than off-site milling. Economic modeling for low sulfide vein gold deposits indicated the RMV necessary for a 15% DCFROR for an open-pit mine, off-site mining operation ranged from $S4/mt at 2,900 mtpd to $71/mt at 360 mtpd, and from $49/mt at 2,900 mtpd to $100/mt at 360 mtpd for an on-site milling operation. Off-site milling was less costly than on-site milling until production exceeded approximately 1,700 mtpd. Then, economies of scale reduced operating costs enough to offset the higher capital costs required for on-site milling.

Jan 1, 1995

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if primary gas toxicities that evolve during the early (~300° C) and later (~.400° C) combustion stages of polyvinyl chloride and chlorinated brattices could be predicted by a smoke particle characteristic, which could be used as a simple and inexpensive test parameter. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 2500 and 1,0000 C, for 14 min duration, with an airflow through the furnace of 10 L/min. The variables studied, as a function of time, were the hydrogen chloride (HCl) and carbon monoxide (CO) concentrations, sample and furnace temperatures, the sample mass weight loss, the average smoke particle diameter (dg and number concentration (no), and the product of the average smoke particle diameter and concentration (dgno)' Results show that the inverse of the smoke particle diameter-concentration (l/dgno) correlates directly with the primary gas toxicities evolved during both stages of combustion.

Jan 1, 1989

By E. M. SEELEY, F. S. LOTT

The total capacity of the natural-gasoline industry to produce light hydrocarbon products increased to 21,322,000 gallons ( 507,670 barrels ) daily on January 1 , 1948 , from 17,928,000 gallons ( 426,860 barrels ) daily on January 1 , 1946. Expansion of the industry in the first two post -war years , 1946 end 1947 , thus averaged 9 percent annually , compared with 6 percent annually in the last two war years , 1944 and 1945 . The number of cycle plants increased only from 37 to 39 in the years 1946 and 1947 , and total capacity of these plants gained 21 percent to 5,857,000 gallons de ily on January 1 , 1948 , represent ing 27.5 percent of the total capacity of the industry , compared with 27.0 percent on January 1 , 1946. All other plants decreased in number in the two-year period from 589 to 510 on January 1 , 1948 , but their total daily capacity increased 18 percent to 15,465,000 gallons . The daily capacity of the average plant in the industry was enlarged from 28,600 gallons on January 1 , 1946 , to 38,800 gallons on January 1 , 1948 , continuing the long -established trend to producing units of greater size and efficiency . The average cycle plant capacity increased from 131,000 gallons daily to 150,200 gallons daily on the same dates as the average capacity of all other natural -gasoline plants increased from 22,200 gallons to 30,300 gallons . Owing to the elimination of small , obsolescent plants in Illinois , Oklahoma , and Pennsylvania , these States experienced the greatest reductions in numbers of plants in 1946 and 1947. In Oklahoma and Texas , several consolidations of two or more plants into a single operating unit were reported . Louisiana and Mississippi were the only States in which the number of plants increased , but daily capacity to produce light products was larger in eleven States on January 1 , 1948, than two years earlier . Added facilities in California and Texas accounted for 41 and 36 percent , respectively, of the national gain in capacity .

Sep 1, 1948

By Walter R. Storms

This paper , which describes the mining methods and costs at the Atwood copper mine in the Lordsburg ( Virginia ) Mining District of Hidalgo County , N. Mex . , is one of a series being prepared by the Mining Division of the Bureau of Mines on mining practices , methods , and costs in various mining districts of the United States . The mine and surface plant are situated in the west half of sec . 7 , T. 23 S. , R. 18 W. , about 3 miles by road southwest of the center of Lordsburg , near the old abandoned townsite of Valedon ( see fig . 1 ) . The main line of the Southern Pacific Railroad passes through Lordsburg , as does the paved eastwest U. S. Highway 70-80 . A spur line of the Southern Pacific ends near the mine . A good graded road connects the mine with Lordsburg . The following pages present a brief history of the district , describe the geology , and outline methods of prospecting and exploration, including sampling and estimations of tonnages and values . Development, and mining methods are explained , and transportation , ventilation , drainage ,. safety measures , and organization are described . The wage scale and costs of development and mining comprise the corrcluding sections of this circular .

May 1, 1949

By James A. Wasson

This report analyzes the petroleum-production potential of the basal Greenbrier dolomite zone, Sycamore-Millstone field, Sherman District, Calhoun County, W. Va., through the application of certain secondary-recovery methods. The well logs obtained and the core recovered from a well in this formation permitted an evaluation of the productive capability of the reservoir, Approximately 120,000 stb of oil may be produced from a 20-acre five-spot unit at breakthrough if the property is waterflooded. At an assumed limiting producing gas-oil ratio of 20)000 sef/stb, approximately 69,000 stb of oil should be recovered by low-pressure gas drive.

Jan 1, 1967

By K. P. V. Lei

The Bureau of Mines investigated molten salt electrorefining 'n helium atmosphere cells as a means for the production of ductile vanadium. 'Electrolytes composed of NaCl-VCl2, LiCl-NaCl-VCl2, BaCl2-KCl-NaCl-VCl2 KCl-LiCl-VCl2, and CaCl2-NaCl-VCl2 were tested. Two electrolytes, KCl-LiCl-VCl2 and CaCl2-NaCl-VC12, were selected for laboratory-scale production tests. A molten salt electrorefining process was developed for the production of ductile 99.6 percent vanadium from a commercial 90-percent grade. Using the CaCl2-NaCl-VC12 electrolyte, an 87-percent recovery of ductile vanadium was made; an 85-percent recovery was made with the KCl-LiCl-VCl2 electrolyte.

Jan 1, 1967

By D. J. Parker, J. B. Benson, J. H. Bird, F. E. Cash

"INTRODUCTION The organic act that became effective July 1, 1910, imposes two very definite primary obligations upon the Bureau of Mines: (1) The prevention of loss of life and limb and the protection of the health of workers in the mineral industries, and (2) the conservation and scientific utilization of the country's mineral resources.The subject of this publication falls within the scope of both of these responsibilities by reason of the fact that (1) certain safety precautions are involved in combating even surface fires and, (2) although peat is not now, so far as known, utilized commercially or otherwise in this country as a fuel, it is extremely valuable agriculturally in at least one of our States, The justification for the conservation of such low-grade fuel through fire prevention appears warranted because of its present value to agriculture and the possible advantages accruing to future generations as a source of heat and power.Although the Bureau of Mines has published information on the origin and uses of peat, this is the first attempt to give out data concerning the prevention and control of peat-bog fires. Although the information presented here is restricted to the Lake Superior District, California, and Florida, there may be similar conditions in other sections of the country that have not come to the attention of engineers of the Bureau of Nines."

Jul 1, 1947