Search Documents

By K. A. Lapakko, D. A. Antonson

Fourteen samples of pyrite-bearing Archean greenstone rock (d < 6.35 mm, 0.04% < St < 1.22%) were characterized (particle size, chemistry, mineralogy) and subjected to laboratory dissolution testing. The only sulfide and carbonate minerals identified were pyrite and siderite, respectively. Quartz, chlorite and sericite typically comprised 90 to 98 percent of the mineral content. For the first 60 weeks, seven samples with sulfur contents less than or equal to 0.16% produced drainage pH values exceeding 6.0. Over this period, six of the seven samples with sulfur contents greater than or equal to 0.20% produced drainage pH below 6.0, with minimum values ranging from 3.2 to 4.7. The seventh sample (0.72% S) had a siderite content of 18%. Small amounts of magnesium and, to a lesser degree, calcium carbonates present in the siderite apparently dissolved to neutralize acid and maintain drainage pH above 6.0. Sulfate release rates generally increased as sulfur content increased, and the rates of pyrite oxidation estimated for individual samples were roughly half to five times that reported in the literature for the abiotic oxidation of pyrite by oxygen. Observed neutralization potentials ranged from 0.2 to 2.0 g CaCO3/g rock.

Jan 1, 2002

In September 2003, a test was conducted to see if a115-mm- (4.5-in.-) diam Mocap Vari-Stem blasthole plug could improve the pattern of explosives using different top stemming material. The test took place at the J.S. Faulkroad and Sonsstone quarry in McCalisterville, PA. The test consisted of a production stone blast. Half of the holes were stemmed with standard crushed stone. Two-thirds of the remaining half were stemmed with Vari-Stem plugs and crushed stone. And the remaining one-third of the second 50 percent was stemmed with Vari-Stem plugs and only drill cuttings.

Jan 1, 2004

By S. M. Khandrika

It is shown that dewatering of fine coal particles (D50 : 21 microns) is enhanced near the point of zero charge. The coal surface is modified by the addition of copper ions and adjusting pH to precipitate surface active metal hydroxy species which promote agglomeration and produce low moisture cakes. Filtration kinetics data are used in calculating filter cake parameters from an integrated form of Darcy&apos;s law. The influence of copper ions and pH on filter cake parameters and correlations among them are presented.

Jan 1, 1993

By T. J. Batchler, K. M. Mohamed, D. F. Gearhart, R. K. Zipf

Seals are explosion-resistant structures built in underground coal mines to isolate abandoned mining areas from the active workings. An equivalent single degree of freedom (SDOF) method such as the single-degree-of-freedom blast effects design spreadsheet (SBEDS) developed by the U.S. Army Corps of Engineers can be used to design seals to resist mine explosions. The critical input for the SDOF code is the seal resistance function. The objective for this study is to develop engineering data for design of plain concrete (PC) and reinforced concrete (RC) seals using finite element (FE) models. The FE models can then be used to generate resistance functions for different PC and RC seal designs, which can be used in the SDOF codes. The U.S. National Institute for Occupational Safety and Health (NIOSH) researchers designed and built a test fixture for use in conjunction with NIOSH’s Mine Roof Simulator to apply a four-point bending load on the face of the tested seal. Eight large-scale experiments for each PC and RC seal were conducted. The experimental design considered the effects of the foundation strength, hitching and roof-to-floor convergence. Calibrated FE models for PC and RC seals were developed using ANSYS Ver. 13. With a very limited number of engineering-based assumptions and a single set of data—including Young’s modulus, compressive strength, stress-strain relationships, etc.—the PC and RC seal models successfully calculated the recorded resistance functions and failure patterns for a wide range of boundary conditions. Plug and RC seals were assumed for a 1.83-m- (6-ft-) high entry to demonstrate the application of the calibrated finite element models for calculating the resistance functions of these seals. The resistance function of a particular plug seal case was found to be a bilinear relationship. The resistance function of a particular RC seal without shear reinforcement was found to be a nonlinear relationship.

Jan 1, 2013

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel&apos;s support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By J. F. Hutwelker

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P209 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Low air flow rates adversely affected concentrate grade at the lower throughput. At the higher throughput, phosphate recovery decreased at an elevated air flow rate. An unexpected result of the study was the effect that frother type had upon phosphate metallurgy. Use of Nottingham Econofroth 925 provided better flotation selectivity than American Cyanamid F-65 at the low throughput. This is significant since the high&apos; throughput tests were conducted with F-65 exclusively. It is reasonable to expect further improvement in high throughput performance when the optimal frother type and dosage are determined.

Jan 1, 1993

By J. B. Gwiazda

S. Budirsky J.B. Gwiazda&apos;s article deals with an interesting problem that has not been studied thoroughly up to now. Gwiazda has proposed a technical solution that eliminates horizontal load imposed by the supports on the roof. That load is due to a discrepancy between the trajectories of the canopy and the overlying strata. It is true that the improved lemniscate guidance system proposed by Gwiazda could eliminate the horizontal load but, on the other hand, it would represent a higher cost of the supports, and it would complicate the already complicated mechanism of powered supports. That is why we must be convinced that the proposed improvement is actually needed. From that point of view, the following questions should be elucidated. As shown in Fig. 1, the point 0 travels along the curve a, which produces horizontal load on the roof in the direction of the coal face. As stated by Gwiazda, "such a high load is capable of destroying the roof above the support, causing rock debris to be scattered around the face." The results of our measurements carried out in coal mines of the Czechoslovak part of the Upper Silesian Coal Basin show that the convergence in the modern type of powered supports does not exceed several millimeters (not more than 10) per hour. Similar conclusions were drawn from field measurements performed in the Polish part of the Upper Silesian Coal Basin (see S. Romanowicz and H. Szopka in Proceedings, Scientific and Technical Symposium Simmex&apos;85, Katowice, Poland, pp. 73-83). The small vertical closure of the supports also induces a small horizontal displacement of the canopy. In addition to this, the transmission of forces between the roof and the canopy is influenced by the layer of debris on it, i.e., the canopy slides without imposing a greater horizontal load on the roof. This was deduced from field measurements of Voest-Alpine F 4/4500 powered supports equipped with rams instead of the common front lemniscate links (denoted as 1 in Fig. 5). In these supports, the pressurizing of the space of piston rod (1a in Fig. 5) causes the rams to close, which induces horizontal load on the roof in a direction toward the coal face. After the setting of a support unit, the pressure in the piston rod space was found to drop, frequently to zero, because the small horizontal sliding between the canopy and the debris or inside the debris caused the horizontal reaction from the roof to fall to zero, although the debris were pressurized by vertical setting load. As a consequence, there was no horizontal load imposed by the canopy on the roof. A rise of the horizontal load was recorded only after the passage of the shearer and during lowering of the adjacent units. Thorough information on the results of the aforementioned field measurement is given in the paper, "Analysis of the performance of shield powered supports installed in a thick seam," published in Mechanizacja i automatyzacja gornictwa, 1982, No. 12, pp. 38-46. An English translation of the paper is available from the author. We have deduced from our observations that horizontal load imposed by the canopy on the roof in the direction toward the coal face is useful for roof control because it limits the displacement of the immediate roof toward the gob particularly during the rise working. We came to the conclusion that horizontal load on the roof toward the coal face should be induced on purpose. Could Mr. Gwiazda prove with the results of field measurements his contrary opinion? Has the small horizontal displacement of the canopy toward the face actually had an adverse effect on the roof? As shown in Fig. 2, during the setting of a support unit, the canopy imposes a horizontal load on the roof in the direction of the gob. In this case, I share Gwiazda&apos;s opinion that the horizontal load could have an adverse effect on the roof. Nevertheless, two important circumstances were neglected - the horizontal compliance of the supports and the interaction of adjacent units. The question of the compliance was analyzed precisely by I. Krumnacker in Gluckauf-Forschungshefte, 1984, No. 5, pp. 219-223. He found that due to the clearance between the hinge pins and the eyes of the sheild and due to the elasticity of the steel structure,

Jan 1, 1987

By Jim Nickerson, James McCleish, Tom Abkemeier, Nicholas Willig

The purpose of this project is to convey sanitary sewage from an existing pump station to a new waste water treatment plant. This paper will discuss the design and construction aspects of the project. The scope includes construction of three main shafts ranging from 34 to 100 feet in diameter at depths of 200 to 230 feet and 21,000feet of tunnel. Shaft construction consisted of slurry wall excavations keyed into claystone and limestone at depths ranging from 114 to 130 feet, followed by rock excavation utilizing drill and blast methods. The tunnel is being excavated in the Warsaw and Salem shale and limestone formations utilizing a 12&apos;-6" diameter Wirth hard rock TBM.

Jan 1, 2005

By M. A. Oskouei

Draglines are the main energy consumers in strip mines. Given the growing cost of energy and environmental concerns, it is important to properly understand dragline energy efficiency. The goal of current research at Missouri University of Science & Technology is to account for operator practice and operating conditions in modeling dragline energy efficiency. This paper presents preliminary correlation analysis and a framework for stochastic modeling of dragline energy efficiency. Thirteen operating parameters (including cycle times, payload, swing angle, and height of dump pile), operator working schedules, operating conditions, and drag, hoist, and swing energies were monitored for an 85 yd3 dragline. Operator effects were examined by two-sample t-tests. The relation between the parameters and energy consumption were assessed by correlation analysis and a stochastic modeling framework has been proposed for dragline energy efficiency. The results show that operator effects are significant (p< 0.05) and energy efficiency is correlated with operating parameters. The completed model will help the coal mines better predict energy consumption, with uncertainty, for different operating conditions.

Feb 27, 2013

By W. K. Callaway

The need to increase ore recovery and pillar stability caused the Magmont Mine staff to investigate the use of sandfill to accomplish both tasks. The use of hydraulically stowed classified mill tailings as a subsidence preventative will be discussed as well as the use of sandfill in pillar recovery and as a part of the regular mining cycle.

Jan 1, 1986

By Dennis P. Martin, Michael M. Fitz, James E. Friant

Methods for reducing the cyclic nature of drill and blast tunneling operations have been long needed. A miniature blasting system using 10 mm (.375 in.) holes, 0.91 m (36 in.) deep, and blasting only one hole at a time makes it practical for men to work behind a shield, remaining at the face during the entire process. A prototype automated module was developed to drill, load the hole and initiate the detonation without moving from the hole. A unique cost effective gell explosive and a novel, low cost initiation method were developed.

Jan 1, 1989

By G. Deschênes

Following a successful investigation on the Central Zone sample, a cyanidation study was conducted on an ore sample from the AD-MW Zone of Clarence Stream Property, owned by Freewest Resources Canada, to develop a leaching strategy to extract gold. At a grade of 6.48 g/t, gold is present in the forms of aurostibite, free gold and electrum. The ore contains 4.3% berthierite/gudmundite, 1.3% pyrrhotite, 0.7% pyrite, 0.07% stibnite and 0.9% arsenopyrite. Similar to the Central Zone, the extraction of gold from the AD-MW Zone can be performed at atmospheric pressure, pH 10.5 and with a low concentration of cyanide. The grind size had no effect on gold extraction between a P80 of 28 to 71 µm. The oxygen and cyanide requirement significantly increased with a ?ner grind. Consequently, a very close control of cyanide addition is required to minimize passivation of gold. Lead nitrate, added in the pretreatment, increased the extraction of gold by 2.3%. Leaching at pH < 10 improved gold extraction but increased the cyanide consumption by 5%. Passivation of gold occurred when the pretreatment was longer than 2 hours. A longer pretreatment reduced the cyanide consumption by 5%. Mineralogical characterization of the leach residue with no gravity pretreatment prior to leaching indicated the presence of unleached gold grains and passivated gold grains. Removal of coarse gold by gravity increased the extraction by 2.8% (leach residue at 0.74 g/t Au). Increasing the DO to 16 ppm or the lead nitrate from 500 to 1,000 g/t increased the overall gold extraction to 90.4% (leach residue at 0.62 g/t), which is the maximum gold extraction obtained. The leaching parameters were 800 ppm NaCN, DO 16 ppm and pH 10.5 for a duration of 120 hours. The associated cyanide consumption was 4.0 kg/t. Gold leaching was not sensitive to cyanide concentration. Reducing the cyanide concentration to 250 ppm resulted in a gold extraction of 89.5% with a cyanide consumption of 2.6 kg/t.

Jan 1, 2009

By Roy A. Grancher

CYCLING WITH CEMENT "THE WHEEL IS COME FULL CIRCLE" Shakespeare&apos;s King Lear Act V, Scene 3, Line 176 The time clock of the cement industry has been turned back to the early 1950s. After the trials and tribulations of the decade of the Sixties, the hands now stand where they did just over twenty years ago. Cement shipments have steadily increased, with a record 419 million barrel level (78.8 million tons) being reached last year. Plants are operating at average utilization rates in excess of 85 percent of rated capacity. The spread between supply and demand has narrowed to where a definite shortage of cement now exists within the industry. The notable and unfortunate difference between the two periods however is that, back then, cement&apos;s returns were a respectable 14 to 18 percent, whereas today they stand at less than half those levels. Insufficient return forms the present foundation of the U.S. cement industry. This lack is destined to have a cumulative effect. Just as the industry&apos;s balance between supply and demand is returning to favorable proportions, promising a period that has historically and now should generate those profit levels required to modernize and provide for capacity addition, cement instead finds itself frozen by federal price controls into the semi-depressed condition that has existed for over a decade and from which it was just starting to emerge. Capital is not attracted to continued low returns, and increasingly restrictive pollution control measures are necessitating great non-productive expenditures be made as definite costs to stay in business. Even a clouded crystal ball would reveal that additional cement plant closings can be expected.

Jan 1, 1972

By John H. Gasper

The success of steep slope (>20°) contour mining depends on many factors. Most important is the selection of the mining method that best suits the premining site conditions environmentally and economically. These conditions can be divided into three categories: • Geometric conditions - machine limitations, slope stability restrictions, erosion capacity; • Physical conditions - material properties, rock strengths, ability to dig, driving surfaces; and • Chemical conditions - acid-base relationships, blending or selective placement of overburden. This article incorporates these conditions by conceptually modeling compliance-oriented contour mining methods, particularly haulback methods, using the combined front-end loader (FEL)/ truck, tractor/scraper, and FEL-truck and scraper. Engineering analyses, including machine selection, sequencing, ease of varying production rates, slope requirements (for stability and running surfaces) and drainage requirements can be performed after the geometric constraints dictated by in situ conditions and regulatory requirements have been conceptualized. Once all generalized geometries have been established, reduction to idealized, three-dimensional views is achieved. These are then reduced to two-dimensional symbolic models, mainly plan views but also elevations and sections. Equipment activities and operations are then conveniently overlayed. Without this simple, two-dimensional reduction, technology transfer remains awkward and non-analytical.

Jan 1, 1991

By Michael V. Mergentime, Prakash M. Donde

The Nutley Quarry Trunk Sewer Project is a good example of a tunnel that went through difficult and complex ground. The 2 m (7ft.) diameter and 840 m (2,750 ft.)long tunnel passed through soft ground, mixed face, and hard sandstone. The soft ground and mixed face tunneling provided several challenges. During excavation of the tunnel, the Contractor encountered a number of unanticipated large boulders. In addition, the length of the mixed face portion of the tunnel increased by 100%. The Contractor tried various construction techniques to overcome the difficult ground conditions and complete the project. The tunneling progress was slower than expected. The Contractor claimed extra costs for differing site conditions. Through discussions and negotiations between the Contractor, Engineer, and Owner, all of the changed condition claims were settled before the construction of the project was completed. This paper addresses the difficult ground conditions, claims evaluation, and how they were resolved by cooperative efforts between the Contractor and the Owner/Engineer.

Jan 1, 2001

By J. H. Daniel, S. Krzemien

Partners In Economic Reform, Inc., established a Polish-American Mine Center in Katowice, Poland, in 1996 to improve working conditions in the minerals industry. The program was based on the experience of mining companies, government, and labor in the United States, and was executed by a Coordinating Committee headed by the Center Director and Polish leaders from industry, State, labor, and academia. The cooperation among all parties has enabled safety and health issues to become part of industry restructuring with impressive initial reductions in coal mine fatalities. Existing work practices and attitudes of labor and management were assessed in coal mines throughout the country. Promotion, Rules, and Job and Task Analysis were identified as the areas requiring the most improvement, and are part of a post-graduate Safety Management program. Demonstration projects included measuring dust levels, using safety glasses, and promoting hazard awareness. Improved labor-management relations increased cooperation allowing for effective transfer of technology. Results can also be applied to improve the working environment of the manufacturing sector also undergoing restructuring.

Jan 1, 2001

By K. Lapakko

One responsibility of the Minnesota Department of Natural Resources is to encourage the development of mineral resources within the state. A second responsibility is to ensure that mineral development does not adversely impact other natural resources, including the water resources of the state. One approach the Division of Minerals has taken to fulfill these responsibilities is to conduct cooperative research with the mining industry. To encourage mineral development the Division has cooperated with industry on projects related to exploration, mining, and mineral processing. To examine environmental issues the Division has worked in concert with iron ore, base metal, and precious metal exploration and mining companies, as well as the Western Governors&apos; Association, US Bureau of Mines, US Bureau of Land Management, and the US EPA for the past 20 years. These projects were conducted to evaluate methods of predicting, preventing, controlling, and treating problematic mine waste drainages, as well as mine waste revegetation. This paper I) briefly summarizes cooperative projects conducted, 2) enumerates elements which have contributed to the success of cooperative projects, and 3) describes changes implemented for future projects at the Division&apos;s new field and laboratory research facilities, as well as at existing mine and plant sites.

Jan 1, 1998

By M. C. Roberts

As nations advance through various stages of economic development, the patterns of demand for minerals change. For example, as a nation develops from a subsistence economy through industrialization and into a service based economy, the use of minerals is at first low, then grows rapidly, and finally stabilizes. The past trends in the use of agricultural minerals by the currently advanced nations provide a pattern that the world as a whole may follow as it progresses through the stages of economic development. Future needs for agricultural minerals are estimated using this approach.

Jan 1, 2001

By William Gleason

From Nov. 16-20, the Extraction 2025 Conference will be presented in Phoenix, AZ. The unique conference brings together the 12th International Copper Conference, the 6th International Symposium on Nickel and Cobalt as well as cross-cutting symposia. Extraction 2025 is co-organized by The Metallurgy and Materials Society (MetSoc) of the Canadian Institute of Mining, Metallurgy and Petroleum (CIM), the Society for Mining, Metallurgy & Exploration (SME) and The Minerals, Metals & Materials Society (TMS). The previous, and first Extraction meeting (Extraction 2018) was held jointly by these three societies seven years ago in Ottawa and was a huge success with more than 90 percent of respondents indicating interest in attending a future event. Kimberly Mills, senior process engineer at Samuel Engineering, is the lead for SME. “This installment of Extraction is featuring Copper 2025, Nickel-Cobalt 2025 as well as crosscutting symposia,” said Mills. “All three societies participate on the International Organizing Committee for the Copper Conference Series and are well situated to host this event together. TMS is also hosting the Ni-Co conference this year and agreed to include it as part of Extraction. There are many aspects that can be shared between these commodities to share information on processing technologies and to learn from each other.” SME is the overall conference chair and running the logistical aspects of the event, which includes managing all aspects of the venue and the registration system as well as tours and short courses, Mills said. “SME has many dedicated members serving in various capacities on organizing and programming committees, including Nick Gow serving as Technical Committee Co-Chair for Copper and Adam House assisting on the Copper IOC.” When Extraction 2025 kicks off, it will be focused on the metals needed for the global energy transition with a special focus on copper and nickel-cobalt. “With as rapidly as the industry is changing and the huge demands for these metals we have some serious challenges ahead of us,” Mills explained. “These challenges require collaboration, creative solutions and engaging experts, both inside and outside of our fields, with a push for sustainable sourcing, ethical supply chains, environmental and social responsibility.” The International Copper Conference was started in 1987 as a collaboration between the Institute of Mining Engineers of Chile (IIMCH) and MetSoc of the CIM. The event is typically held every four years and has always been held as a standalone or headlining event at a society annual meeting, said Mills. “Over the years, this conference series alone has brought together members of IIMCH, MetSoc, TMS, SME, the Society for Metallurgists and Miners from Germany (GDMB), the Mining and Materials Processing Institute of Japan (MMIJ), the South African Institute of Mining and Metallurgy (SAIMM) and the Nonferrous Metals Society of China (NFSOC),” she added. “Being a part of Extraction allows for even more sharing of ideas and expansion of networking. This conference has not been held in the United

Oct 1, 2025

By J. A. Delgadillo

Computer simulation and mineral modeling was applied to the optimization of a grinding circuit in a plant processing 256 t/h magnetite. These tools were used to develop a grinding and classification configuration to decrease the grade of silica in the magnetite concentrate, which is produced by the plant. Empirical grinding and classification models were finely tuned using plant experimental data. The JKSimMetTM 5.0 software was used to simulate the grinding and classification units. By applying changes in the original circuit, a throughput increment of 100% was achieved with an important reduction in the energy consumption. The silica content in the magnetite concentrate can be decreased by regrinding the coarse fraction of fine screens into a separate ultrafine grinding unit instead of returning this flow to the ball grinding mills.

Jan 1, 2008