Search Documents

By A. K. Sheik, W. G. Pariseau

A small underground mine in northern Idaho was used as an experimental facility for studying the role of water in the analysis of mine opening stability. Laboratory test data, borehole measurements and geological mapping assisted in constructing a coupled finite element model of the rock mass. The model was used to make quantitative estimates of: 1) rock stress, strain and displacement changes, and 2) water pressure and flow velocity changes that occurred during historical mining. Stope cuts and wet fills were included in the analysis. Stability of crown pillars between stopes was of particular interest. The relatively low effective stress and high rock mass strength showed that water pressure changes were of no great consequence in agreement with experience. The computational tools used in the analysis may be applied to other wet mines with appropriate changes to site-specific input data.

Jan 1, 1999

By Jr. Gambrell

Support characteristics of in-cycle trusses are analyzed using a photo-elastic model loaded by tightening a truss in the sequence normally used in an underground mine. Stresses in the roof at its center point and at the junction of the roof and rib are examined. Effects of zero tension and unequal tension in the inclined anchor rods are presented. Effects of simulated subsidence on stress in the roof surface and on tension in the separate truss members are examined. Conclusions are drawn relating to (1) the effects of tension in the inclined anchor rods on uplift and compressive stress parallel to the roof surface, (2) the effects of subsidence on stress in the roof surface and, (3) the effects of subsidence on tension in the truss members.

Jan 1, 1989

By Robert T. Beckman

Education of inspection and operating personnel is essential to protection from radiation hazards in the mining industry. For over 10 years, MSHA has presented the only formal course on radiation measurements and control available to the mining community. Course objectives and content are described in this paper.

Jan 1, 1981

By Arafat Ghosheh, Yousuf Abu-Rish, Darwish Amara, Mohammed Baderkhan

The Jordan Phosphate Mines Company is one of the world's major phosphate rock and phosphatic fertilizers producers (the second largest phosphate rock exporter), with ore reserves exceeding 2 billion tonnes, mainly located in the Eshidiya area. The Eshidiya phosphate deposits, 120 km north-east of Aqaba, are of sedimentary origin (as are all phosphate ore in Jordan). Three exploitable beds (Al, A2, and A3) with variable content of P205, CaO, SiO2, etc., are processed in order to produce 68-70,73-75, and 75-77% TCP grades. The A3 bed, which is characterized as the most siliceous containing 40-48% TCP, requires physical beneficiation using wet scrubbing, screening, and desliming by hydrocylone, followed by anionic conventional flotation to achieve 75- 77% TCP grade. For the last 15 years extensive laboratory and pilot tests (including physical, chemical, and mineralogical studies) were carried out. After operating the industrial plant, certain modifications were deemed necessary to adjust the operational parameters and the final flowsheet, which was followed to obtain the targeted quantity and quality of concentrate.

Jan 1, 1999

By J. C. Squire, E. W. Baker, G. A. Sullivan, G. W. Flathers

A mine collapse severs communication with trapped miners. Landlines are crushed and commercially available radios cannot penetrate hundreds of feet of dense, conductive earth without the use of regenerative repeaters that may also be crushed. This paper describes a proof-of-concept device that uses seismic P-waves, instead of radio waves, to allow communication of a code that represents prearranged messages, including the safe haven location identifier, number of people and air quality, from trapped miners to aboveground rescue units. The transmitter designed is about 0.03 m3 (1 ft3) in size and can broadcast for four hours from its 27-kg (60-lb) battery pack. The receiver consists of a geophone and a 2.5-kg (5.5- lb) signal conditioning unit attached to a laptop computer, which displays the communication signal in real time. Testing in a bituminous coal mine with an MSHA representative revealed the device was able to transmit through 271 m (890 ft) of overburden, at 0° and 12° from vertical, using 500 W of power.

Jan 1, 2009

By Alfred Haack, Günter Girnau

INTRODUCTION From 1967 to 1976 in the Federal Republic of Germany about loo km tunnels and 125 underground stations were constructed for municipal and commuter railways solely. Additional a remarkable amount of road tunnels and sewers were built. In 1977/78 a further 27 km railway tunnels, 3.5 km road tunnels and 65 km sewers and utility lines were under construction. This shows an enormous volume of tunnel construction work. In connection with this activity various technical research and development programmes have been carried out. They deal with nearly all fields of underground works as for example soil and ground exploration, excavating and lining techniques, calculation and last but not least waterproofing problems. It is impossible within the framework of this report to touch on all the problems. Therefore, only one problem area with its different aspects will be discussed: waterproofing systems and their last developments in Germany, especially, joint sealing with special consideration of the waterproofing of concrete segmental tunnel lining (1)

Jan 1, 1979

By Vincent J. Murphy

INTRODUCTION Geophysical applications to engineering projects are usually considered for reconnaissance exploration, and for some preliminary design phases. Recent experience indicates a growing need and a greater number of requests for measurements during construction. This is particularly true where seismic velocity values are related to strength properties of rock. Typical project objectives during construction are: dike and tunnel realignments required by surprise conditions encountered during foundation preparation; checks on grouting effectiveness which require velocity measurements before and after grouting; and dynamic moduli measurements along the walls of tunnels and deep excavations. This paper considers one of the on-site seismic applications that is rather simple and straightforward, and yet has few references in the literature. The specific objective is the measurement of seismic velocities (both "P" waves and "S" waves) for determining the thicknesses and dynamic moduli values of loosened zones of tunnel wall rock. PRE-EXCAVATION SEISMIC METHODS The seismic methods suitable for engineering project studies are well known and especially suited for routine site reconnaissance; these are illustrated in Fig. 1. The seismic refraction profile with a

Jan 1, 1997

By J. K. Mohanty, D. Panda, P. K. Sahoo, R. K. Paramguru, K. C. Nathsarma

Ferromanganese slag, a product of the manganese industry, was characterized mineralogically. The slag, which contains high Mn values, was characterized using optical microscopy, XRD analysis and electron microscopy. No separate Mn-bearing oxide mineral phase was found. The slag is amorphous, and no crystalline phase was identified in the hulk sample by XRD, However, in. fine fractions, quartz was identified. Scanning electron microscopy (SEM) revealed the presence of Mn, Si, Al and Ca in the matrix without the development of a mineral phase. Leaching experiments using H2SO4 were carried out to determine if Mn could be extracted from the slag. At room temperature, almost 100% of the manganese could be dissolved at a solid-liquid ratio o f 1:10 by leaching with dilute sulfuric acid. The impurities could be precipitated by pH adjustment to produce a manganese sulfate solution suitable for the production of MnO2 or electrolytic Mn metal. Based on the laboratory-scale experiments, a suitable process is proposed to recover manganese values from the, ferromanganese slag.

Jan 1, 1999

By H. Soto, J. Jara, F. Nava, J. B. Hiskey, B. J. Scheiner

Laboratory tests showed that ozone can destroy free cyanide and weakly complexed cyanide (copper and zinc cyanides). The iron cyanide complexes were resilient to ozonation but they were effectively eliminated by precipitation with Fe (II) ions under controlled pH conditions. Tests carried out with effluents from a number of gold mills confirmed the results obtained previously in the laboratory. The industrial samples contained cyanide in the form of free cyanide and also complex copper, zinc and iron cyanides. Solutions that contained up to 184 mg/L total cyanide, after the ozone treatment analyzed only 2-3 mg/L dissociable cyanide and 50-90 mg/L CN(t) (accounted for by iron complexes). After precipitation with ferrous ions total cyanide was reduced below 1.5 mg/L. For most solutions ozone consumption ranges from 3 to 6 g per g of cyanide destroyed. However, certain impurities (such as SCN and S203 ), present in some effluents, increase ozone consumption and make it more difficult to reduce copper concentration to satisfactory levels.

Jan 1, 1993

By Edward Finch, William F. Riggs

Selectivity and recovery of many industrial minerals can be directly affected by the carbon length, degree of unsaturation, and melt point of fatty acids used as collectors. Examples of several modifications are provided based on actual experiences of commercial applications. A review of recent history indicates that fatty acid collectors are applicable from C9'C18 in carbon length, however, not for all minerals. The mesh size, density, and surface characteristics of the particular mineral, as well as other related operating conditions, are important in selecting the correct fatty acid configuration. A review of some past programs are submitted as a guideline in the selection of fatty acids and supported by isolated, successful examples demonstrating the effect of carbon length and unsaturation.

Jan 1, 1986

By T. Tamagawa, I. Iwasaki, N. X. Fu, M. Kobayashi

A low-temperature-chlorination selective oxidation followed by aqueous chloride leaching and SX-EW for producing electrolytic copper, elemental sulfur and ferric oxide was investigated for hydrometallurgical processing of a chalcopyrite concentrate. In this article, the selective oxidation phase of the process is described. The selective oxidation requires a temperature well above the CuCl-FeCl3 eutectic points. The test procedure was developed with a batch reactor and then tested with a continuous reactor. The process was initiated by adding small amounts of chlorinated samples to a fluidizing bed of dead-roasted sulfide concentrate micropellets. The selectively oxidized samples thus prepared were shown to fully dissolve copper, while virtually all the iron remained undissolved.

Jan 1, 2000

By Thomas F. Torries

It does not take sophisticated economic analysis to determine the current status of nickel production and demand (Figure 1). One only needs a quick glance at the balance sheets of the major nickel producers to learn that prices are down and profits are supressed to the point where they are major losses. Operations have been closed, and those remaining in production have reduced output. What Is now of interest Is, when will the nickel market improve and to what degree? The purpose of this paper is to attempt to answer these questions. This will be done by the normal method of projecting nickel demand, chosing a production scenario, and analyzing the results.

Jan 1, 1982

By Hingant Pierre

The Hurtières Tunnel was built in 1995 with drill and blast method, in metamorphic schist. It is located between Lyon and Torino on the A 43 motorway in the French Alps. During the construction, a geological hazard was encountered, which caused a massive ground collapse. The tunnel was filled up with 3,000 m3of glacial materials. Geological investigations realized after the accident showed that a narrow glacial valley was present at this location the water table was 40 m above the tunnel level. The paper will describe the collapse and the remedial methods which were implemented to proceed through the failure area. These included drainage works,2,000 m3 grouting and 6,200 ml jet grouting columns.

Jan 1, 1999

By Martin H. Col, Thomas W. Steele

The ability to make a good profit in the mining industry is becoming more and more difficult. Typically, grades are lower, sites are more remote, and environmental restrictions are getting tighter than ever before. While the price of the materials P.roduced, such as gold and silver, have stayed flat or declined, the external costs (goods and services) have increased. Increasingly difficult environmental restrictions have increased the lime and costs of develoJ?in9 new deposits, while often placing restrictions on a mme s production rate. Environmental costs for mine closure and site reclamation also make it very difficult to show a long-term profit while mining. Typically, the answer to this cost/price squeeze has been technological innovation. The whole concept of heap leaching low-grade gold ore is one innovation that provided some very goocf profits to the mining companies; but, today, those profits are being eroded by the continuing cost/ price squeeze. This paper will discuss material handling in a heap leach stacking operation and the alternatives of trucks, grasshopper conveY.or systems and mobile conveyor systems.

Jan 1, 1992

By Anthony D. Hammond

Geographic Information Systems (GIS) are powerful analytical and data display tools for mining industry management, capable of linking spatial features with tabular data and integrating communications across departmental boundaries. This GIS application concentrates in four technical areas of underground mining: ownership and mineral claims; exploration management; production; and mine safety. GIS provides land and exploration managers with the ability to consolidate and archive claim data and to georeference property maps defined in local coordinates into world coordinate systems. It facilitates optimal siting and querying of service installations and refuge chambers relative to production centers. GIS's proximity analysis identifies areas of potential safety concern and points to and maps the shortest routes to emergency exits, facilitating the prompt evacuation of mine personnel.

Jan 1, 2002

By Robert J. Mac Kinnon

A moving grid finite element model for the analysis of transients in a rock mass surrounding an underground coal conversion cavity is presented. Major model components are outlined, including a special element formulated to account for internal discontinuities. A numerical example is described.

Jan 1, 1986

By Ch. Arvanitidis

This paper presents the design solution for an actual case of settlement tanks, for a wastewater treatment plant under construction, actually founded on swelling clay (the nature of which had not been appreciated beforehand) and suffering considerable damage as a result. Two points of interest prompted the use of a numerical model as an alternative approach to the traditional method of analysis: First, the desire to compare the in situ measured deformation and displacement of the tanks with the figures calculated by the numerical model. Second the need to check the validity of the suggested solution as a remedy, i.e. the replacement of a certain thickness of clay by graded material.

Jan 1, 2005

By Thomas M. Larimer

Prior to April, 1961, the coal charge to Clairtonts coke oven batteries was 3" x 0" mine waslied coal having approximately 6.0% to 7.0% moisture. Even at this size and moisture content, the arching, rat-holing and hang-up was excessive and the effective live storage of coal was only 60% to 70% of the rated capacity of the coal bunkers, depending upon the moisture of the coal. In addition, many production delays were encountered in the time and methods required to fill the larry cars. The need for an improved metallurgical coke led to the introduction of pulverized coal to a portion of the plant in 196 1. When the full potential of the pulverizing equipment was realized, we were able to serve seven batteries in our second unit of batteries with pulverized coal through two coal bunkers. The discharge hoppers of these bunkers were equipped with air vibrators to assist the flow of pulverized coal into the larry cars. The vibrators were helpful in this respect but required considerable maintenance and caused damage to the bin plates.

Jan 1, 1968

By J. K. Szymanski, Val Srajer

In this decade mining companies in western Canada have searched for reliable and inexpensive ways to improve mine productivity. Truck dispatching systems, equipment vital sign monitoring and sensing, vehicle guidance systems, have all been considered. In this paper the off -highway vehicle monitoring systems used or planned to be installed at surface coal mines in western Canada are described. The monitoring systems are divided according to their function and application; installation and testing procedures are described, as well as the economic benefits to the mining operation.

Jan 1, 1989

By Robert H. Scott

Developments during the past few years have brought coal-based composite fuels to commercial readiness. During the next few years, composite fuels will become available from a number of suppliers. Potential users must evaluate the combustion properties of these fuels to determine equipment and operating changes required for their use. Most work to date has been done with boiler applications. However, many potential non-boiler applications exist in the metals and minerals industry. These applications require specific evaluations appropriate for the processes involved.

Jan 1, 1982