Search Documents

By Hugh Rose

The properties of the company lie within the Pachuca district, State of Hidalgo, Mexico, connected by three railway lines with Mexico City, 55 miles southwest, and by two lines with Vera Cruz, 250 miles southeast. The ores were formerly divided by sorting into two classes, smelting and milling, the former averaging about 2 oz. gold and 335 oz. silver, the latter 0.12 oz. gold and 23 oz. silver. The smelting ores were sold to custom plants, principally the American Smelting & Refining Co. at Aguascalientes. The milling ores were treated by the patio process at the Guadalupe Hacienda, at Pachuca. This patio was probably the largest in existence at the time and continued in active operation up to March, 1910. In January, 1910, the mines and patio were sold to English interests, represented by Camp Bird Limited. Two new companies were formed, the Compania de Santa Gertrudis, S. A., to operate the mines, and the Compania Beneficiadora de Pachuca, S. A., to build and operate a custom cyanide milling plant. (Pig. 1.) Geology The historical geology of the Pachuca district is described by Fred J. Pope as follows: 1. The most recent sedimentary rooks in the district belong to the Cretaceous period. 2. The Cretaceous rocks were penetrated by large intrusions of ande-site (referred to hereafter as primary andesite) which occur as elliptical dome-shaped masses, striking northwest-southeast. These andesite bodies are from 8 to 15 miles long and from 6 to 10 miles wide. 3. A period of erosion during which the contour of the andesite domes was changed. 4. Andesite flows (secondary andesite) which rest unconformably on the primary andesites.

Jan 1, 1917

By Klaus Schwerdtfeger

The rules of solution of oxygen from H2O-H2-He gas and of nitrogen from N2-H2 gas in shallow melts of liquid iron were measured at 1610o and 1600o C, respectiuely. Concentration profiles were detemined in the liquid iron. Tire rate data indicate that the solution process is controlled by diffusion in the iron melt. The diffusivities for oxygen and nitrogen in liquid iron, as calculated from the present data, are DFe-o = (12 ± 3) < 10-5 sq cm per sec and DFe-N = 11 ± 2) X 10-5 sq cm per sec at the temperatures employed. AN attempt was made by Shurygin and Kryukl to measure the diffusivity of oxygen in liquid iron. In their experiments a silica disc was rotated in liquid iron containing oxygen, and the rate of formation of liquid iron silicate was measured. Assuming that the rate of dissolution of silica is controlled by diffusion of oxygen in the iron, the oxygen diffusivity was computed from the rate data giving Dfe-0 = 6.1 X 5 sq cm per sec at 1600°C. Although this value seems to be of the right order of magnitude, there is no proof of the correctness of the assumptions involved in the interpretation of these rate data. The oxygen concentration in the iron at the iron-iron silicate interface was taken to be that in equilibrium with the silica-saturated silicate melt. That is, it was assumed that no concentration gradient existed in the liquid silicate. This is a questionable assumption, unless it is proved that the thickness of the silicate layer is very much smaller than that of the diffusion boundary layer in the iron. Furthermore, Shurygin et al.1 used the Levich equation2 to interpret their rate data. This equation was derived for mass transfer between a solid disc and a single-phase liquid. The hydrodynamic and diffusion boundary layers in the iron stirred by a disc, via coupling of the silicate melt, may be appreciably different from those predicted by Levich&apos;s derivations. In the present work the diffusivities of oxygen and nitrogen in liquid iron were measured at 1610" and 1600oC, respectively. EXPERIMENTAL METHOD Iron melts contained in high-purity gas-tight alumina crucibles were reacted with H2O-H2-He gas for the determination of the oxygen diffusivity and with N2-H2 gas for the determination of nitrogen diffusivity. At the end of the reaction period, the samples were quenched in a cold H2-He gas stream at the top of the furnace. Oxygen or nitrogen contents in the iron were determined by chemical analysis. Two different types of diffusion experiments were perforxed. To determine concentration profiles, a few rate measurements were made using 4-cm-deep melts. The solidified samples were sliced into discs and each disc was analyzed for oxygen or nitrogen. In another series of experiments, oxygen or nitrogen was diffused into shallow melts (about 0.5 to 1 cm in depth) and the total sample was analyzed to obtain an average concentration of the diffusate. In most experiments, 4- to 5-mm-ID alumina crucibles were used. Some experiments were also made in smaller (3 mm) and larger (7 mm) diam crucibles. This variation in diameter caused no difference in the reaction rate, within the limits of experimental uncertainty. To promote the establishment of a stable density profile in the melt, all the samples were suspended in the lower end of the hot zone so that the top of the melt was hotter by a few degrees. Molybdenum wire resistance heating was used. The reaction tube of the furnace was a gas-tight recrystal-lized alumina tube. In most experiments the furnace was heated by an ac power supply. To check the possibility of inductive stirring, some experiments were carried out in a dc operated furnace, with essentially the same results. The temperature of the furnace was controlled automatically in the usual manner. The temperature was measured with a Pt/Pt-10 pet Rh thermocouple and is estimated to be accurate within ±5°C. The iron used was prepared by melting and vacuum-carbon deoxidizing electrolytic "Plastiron" in a zir-conia crucible. The main impurities are: Si 0.004 pct P, S <0.002 pct Cr 0.005 pct N 0.001 pct Zr 0.002 pct O 0.003 pct Mn 0.004 pct C 0.002 pct The gas composition was controlled by constant pressure head capillary flowmeters. Oxygen was removed from the gas mixture by passing it through columns of platinized asbestos (450°C) and anhydrone. Selected H2O contents were obtained by passing the purified gas through oxalic acid dihydrate-anhydrous oxalic acid mixtures held at constant temperature in a water bath. Water vapor pressure data for the oxalic acid dihydrate-anhydrous oxalic acid equilibrium were taken from the 1iterature.3 The flow rate used was about 1.5 liters per min. The whole system was checked for tightness at regular intervals.

Jan 1, 1968

By R. S. Shoemaker, F. W. McQuiston

The principle of cyanide recovery or regeneration of cyanide from solution, be it a weak wash or a foul solution, is by acidulation. All or part of the cyanogen is converted thereby into hydrogen cyanide which is fixed by an alkali (generally lime) and returned to the cyaniding system (the Mills- Crowe process). The solution is made acid by bringing it into contact with sulfur dioxide. The acidified solution is stripped in a packed tower by a counter flow stream of air in which the air and the solution are brought into intimate contact. The air leaving the tank charged with hydrogen cyanide is then passed to another tank in which it is mixed with an alkaline solution, the latter absorbing the HCN and leaving the accompanying air clean for reuse in removing more HCN from the acidified solutions. Of the recoverable cyanide, 9770 is usually recovered in a three-unit disperser tower system. When there is a considerable content of copper, the solution is made acid following standard procedure; however, the HCN is not removed until the copper is reduced by regeneration. Copper removal at this point may be as high as 90%. After reduction of the copper, the acidified solution then is contacted with a lime solution which brings down calcium sulfate as a second step. The silver, gold, and copper are recovered in the form of a precipitate which can be shipped to a smelter. At the Hudson Bay Mining and Smelting Company, Ltd., most of the precious metals have been recovered in the copper and lead concentrates, but it has been found profitable to submit the flotation tailings to a scavenger cyanide treatment for the recovery of exposed gold contained in pyrite rejected during flotation. Due to the fine particle size, maximum dissolution is achieved in a four-hour contact period. In the cyanidation plant, the thickened flotation tailing at 70% solids is given a four-hour agitation in weak calcium cyanide solution and filtered. Filter cake is repulped and discharged either to the tailing storage area or to the mine as backfill. Clarification, de-aeration and precipitation of pregnant solutions are carried out in a standard Merrill-Crowe unit. Typical analysis of precipitate is as follows: Au, 0.47%, Ag, 4. 88%; Cu, 46.0%; Zn, 13. 8%. Cyanicides in the form of copper minerals limit the reuse of barren solution. To recover the substantial quantities of cyanogen chemically combined with base metals in this solution, a cyanide regeneration plant is in operation. The barren solution is acidified with sulfuric acid in a spray tower where an upward current of air from a blower sweeps the liberated hydrocyanic acid gas to an adsorption unit where it meets a fine rain of lime suspended in plant solution with which it combines to form calcium cyanide. The lime--water solution carrying calcium cyanide is reused in the cyanide circuit. The return gases are drawn into the blower and back to the disperser tower thus

Jan 1, 1975

By Eugene F. Broome, Hugh A. Walls

A diffusion measurement technique based on a shear cell comprised of only two segments is described. The diffusion boundary value problem for the finite capillary geometry is solved in general for any arbitrary initial concentration profile and is subsequently specialized for the modified shear cell problem. Effects of convection and mixing at the shear interface were found to be negligible. Mercury self-diffusion coefficients were determined from -25° to 252°C. These data are in good agreement with those found by Meyer. ALTHOUGH diffusion in liquid metals has been of interest for over two centuries, the need for measurement techniques of improved accuracy and precision has become increasingly apparent as additional data have been obtained and theory has become more refined. These conditions reflect the experimental difficulties inherent in liquid diffusion measurements, in which transport by other processes, such as convection, tends to mask the diffusive transport. Frequently the disagreement between several theoretical predictions is less than that found between different sets of data obtained for a system. Moreover, as has been shown by Nachtrieb,1 diffusion data are needed over much larger temperature ranges if the functional dependence on temperature is to be known. Thus, improved techniques must be devised if experimental data are to augment fundamental understanding of the liquid state and to meet technological needs. The available techniques have been discussed elsewhere.&apos; Of these, only the capillary-reservoir, long capillary, and shear cell techniques will be discussed briefly in terms of experimental advantages and disadvantages. These methods served to establish design criteria for the modified shear cell described here. The capillary-reservoir technique of Anderson and saddington3 has been the most widely used method in recent years. The method offers experimental simplicity relative to other methods and has been employed for high-temperature measurements. Moreover, the mathematical relationship between the measured concentration ratio and the diffusion coefficient is such that smaller values of the ratio are achieved for a specified diffusion time relative to other methods. The amplified errors between the concentration ratio and the calculated diffusion coefficient are diminished at lower values of the ratio.&apos; The method also permits multiple determination by the simultaneous use of several capillaries. Disadvantages of the capillary-reservoir method are primarily associated with the hydrodynamic ef- fects of convection and of placing the capillary in the reservoir. These effects are most pronounced in the region near the open end of the capillary and produce an ill-defined boundary condition between the capillary and the reservoir. Such effects are not amenable to experimental or mathematical correction2 (although this has been suggested4). The long-capillary method of Careri, Paoletti, et al.5-10 involves filling one half of a small capillary tube of 150 to 200 mm total length with material of one composition or radioactivity and the other half with the second part of the diffusion couple. This arrangement eliminates the adverse hydrodynamic effects associated with the capillary-reservoir technique; however, certain other experimental difficulties are encountered in this method. The more significant of these difficulties involve the melting, expansion, contraction, and solidification of the diffusion system. The dependence in some cases of the diffusion coefficient on the capillary diameter noted by Careri et a1.7 (termed the "wall effect") has been alternatively explained by Nachtriebl as a convection effect during solidification. In mutual diffusion measurements, the convection problems associated with melting and solidification are increased because of the differences in melting points and in expansion coefficients between the halves of the diffusion couple. However, the errors caused by convection effects within this method are usually less than those in the capillary-reservoir method. Furthermore, the concentration profile needed to determine concentration-dependent diffusion coefficients by the Boltzmann-Matano analysis can be obtained from this method. Of the previous attempts to use shear cells, only the cell used by Nachtrieb and Petit11,12 appears to have yielded good data. They reduced the mechanical complexity of the conventional shear cell by using a cell comprised of only four segments. Three of these segments were filled with ordinary mercury and the fourth with radioisotopic mercury in their determination of mercury self-diffusion coefficients. The average concentration (radioactivity) was determined in each segment following a period of isothermal diffusion. These concentration values were fitted to concentration profiles obtained from the Stefan-Kawalki tables, and the diffusion coefficients were evaluated. Thus, although the number of cell segments is reduced in their method, some information about the concentration profile can be obtained in terms of the Stefan-Kawalki analysis. Moreover, their cell is suitable for measurement of diffusion coefficients at elevated pressure, as they successfully demonstrated with mercury. Consideration of the design and experimental features of the methods discussed above suggested several criteria for the new cell: 1) a &apos;&apos;total" capillary system, as opposed to a capillary-reservoir system, should reduce adverse convection effects; 2) such a capillary system should avoid the problems en-

Jan 1, 1969

By James B. Austin

Growth of the Society When the Institute was born in May, 1871, it was given the name American Institute of Mining Engineers. Yet from its conception a few months earlier, its genetic code clearly carried the message that metallurgy was equal in importance to mining. Thus, the "call" for the initial meeting, which was sent out in April of that year by three mining engineers, Eckley B. Coxe, R. P. Rothwell and Martin Coryell, gave this first objective of the proposed organization as: "the more economic production of the useful minerals and metals." And this call concluded: "Anyone who may have devoted himself to a particular subject connected with either mining or metallurgy, and who may be possessed of new facts in reference to it, would greatly aid in furthering the objects of the proposed association by preparing a paper giving the results of his experience." In response to this call, a group of 22 men assembled in Wilkes-Barre, Pa., for a 3-day meeting beginning May 16, 1871. On the first day, a set of 20 "Rules" was adopted, of which Number 8 read, in part: "The words mining engineers in these rules comprehend engineers connected with mining and metallurgy." On the second day, 18 officers were elected, of whom nine were not present. Moreover, as if to emphasize that the words about metallurgists were to be taken seriously, one of those elected in absentia was the president, David Thomas, a Welshman who had founded the Thomas Iron Co. and who built the first anthracite-fired, hot-blast furnace in this country. The second meeting of the Institute, held in Bethlehem, Pa., in August, had a more metallurgical flavor, and the third meeting, in November, was held in what was then one of the great steel-making centers of the country - Troy, N. Y. This was the home of the Albany and Rensselaer Iron and Steel Co., which held the American rights to Bessemer7s machinery patents. And it was here that the great American steel master, Alexander L. Holley, carried out a series of experiments that led to improvements in the design and method of operation of the Bessemer vessels. It was at this meeting that Holley and Henry Marion Howe, then a "student" at the Albany and Rensselaer plant, were admitted to membership. Four years later, Holley was elected president of the Institute. Clearly, metallurgy

Jan 1, 1971

By N. S. Stoloff, R. C. Ku, R. G. Davies

The stress-strain behavior of Fe-Co and Fe- V alloys containing up to 25 pct solute have been studied in the temperature range 25° to - 196°C. The microyield stress is independent of temperature for all alloys studied, while the temperature dependence of the ordinary yield stress is large and comparable to that for unalloyed iron. An alloy-softening phenomenon is observed for many alloys relative to unalloyed iron, and appears to be a consequence of removal of inter-stitials from solution and their subsequent agglomeration. The ductile to brittle transition temperature is increased markedly by both cobalt and vanadium. Transmission electron microscopy observations reveal that cross slip and cell formation are restricted with increasing solute, which can account for many aspects of yielding and fracture behavior. IRON and other metals of bcc structure slip on many planes of the (111) zone at moderate and elevated temperatures, giving rise to wavy glide. At low temperatures, however, there is a tendency for slip to be restricted to planes of only one or two crystallographic types; in the case of Fe-Si alloys for example, (110) glide predominates, giving rise to planar slip bands."&apos; Restriction of cross slip at low temperatures in iron has been linked by Brown and Ekvall3 to increased strain hardening in the preyield microstrain region, leading to an apparently large temperature dependence of the yield stress. Support for this view has been provided by Lawley and Gaigher4 from a transmission electron microscope study of molybdenum. They concluded that dislocations at lower temperatures, by virtue of their inability to change planes readily, are unable to interact and annihilate, leading to an increase in internal stress and work-hardening capacity. Restriction of cross slip at low temperatures has also been suggested to be an important factor in determining the ductile to brittle transition of single-phase solids, including metals of bcc structure.5 It is pertinent to note that most solute elements tend to raise the ductile to brittle transition temperature of poly crystalline ferrite,6,7 although in some cases, e.g., Fe-Cr7 and Fe-Al,8 the dilute alloys may actually yield at lower stresses than unalloyed iron. It appears, therefore, that solute elements may have an effect analogous to lowering the test temperature with regard to restricting cross glide. Such an effect has indeed been observed in the ionic alloy system KCl-KBr,9 in which bromine atoms, although causing little misfit and consequently little effect on the yield stress of KC1, have a pronounced effect in restricting wavy glide and inducing brittleness. The purpose of the present investigation was to determine the effects of selected solute atoms on the yield stress and fracture behavior of iron, and to elucidate in turn how the slip character was related to these properties. Since it is known that interstitial atoms exert a strong influence on the mechanical behavior of iron, the solute elements chosen for study were vanadium, which reacts strong with interstitials,10 and cobalt, which does not form highly stable interstitial compounds." EXPERIMENTAL PROCEDURE Four-pound ingots of each of the following alloys were vacuum-melted in zirconia crucibles: Fe-1, 5, 10, 25 at. pct Co, and Fe-1, 4, 10, 20 at. pct V. An ingot of unalloyed iron from the same original stock as that used for the alloy was remelted under similar conditions to eliminate variations in interstitial content arising from differing thermal histories. Chemical analyses of the iron, cobalt, and vanadium melt stock are listed in Table I. All ingots were rolled and swaged, commencing at 850°C, to 1/4-in.-diameter bar. The bars were then annealed at 850°C for 1 hr (except that the 10 and 20 pct V alloys were heated for 2 hr) to give a uniform equiaxed grain size of about 0.05 mm. Tensile samples of 0.125 in. diameter by 0.8 in. gage length were utilized for studies of the ductile to brittle transition. A second set of tensile samples were utilized for microstrain experiments in which strain sensitivity of 1 x 10"6 was achieved by a capacitance method.3 Cylindrical compression samples 0.250 in. diameter by 0.4 in. long also were prepared to study the influence of composition on the macroscopic yield stress, and for metallographic analyses of defor-

Jan 1, 1965

By A. H. Jones

(San Francisco Meeting, September, 1915). THE Belmont mill at Tonopah, Nev., was designed and constructed by the Belmont staff. Ground was broken in August, 1911, and milling operation started July 25, 1912. The metallurgical flow sheet, and the machinery adapted to carrying out operations in accordance with this plan, were decided upon from experience gained in the treatment of Belmont mine ores at the old Belmont mill at Millers, Nev. The detail drawings were made by the-engineering staff of the Tonopah-Belmont Development Co., under the supervision of Otto Wartenweiler, who also .had direct charge of the construction, consulting with the General Superintendent of the company, Frederick Bradshaw, and the writer.

Jan 8, 1915

By J. L. Smith, A. L. Albee

This article presents a series of guidelines by which the geologist can evaluate the likelihood of surface faulting and its probable extent at any given site in Southern California and Nevada. The information is intended primarily for geologists concerned with establishing design criteria for proposed nuclear plants. The geologic problems involved in the location of a nuclear power plant are fundamentally no different from those for other types of installations. They fall into four main categories: foundation stability, landslides and slope stability, shaking due to earthquakes, and surface faulting. For problems in the first three categories the foundation engineer, the geologist, and the seismologist can provide criteria for plant location and design, and these problems can generally be economically handled by appropriate design measures for a project of the magnitude of a nuclear plant. However, problems in the last category — surface faulting — are more difficult to handle and require a unique evaluation. Accordingly, this paper will deal primarily with the problem of establishing design criteria for surface faulting, particularly as it affects nuclear facilities. A nuclear reactor is a power source that for greater safety is contained in a heavy, air-tight structure, just as gas, oil, water, and other power sources must be contained. Surface faulting is significant in that it may reduce the integrity of the containment by affecting critical exterior piping or by breaching of the containment. A similar significance exists relative to dams or tanks for the storage of water, gas, or oil, except that in these latter examples the breaching of the container automatically releases the fluids to do their damage. This is not necessarily the case with the rupture of a reactor containment structure because the function of the containment is totally protective, i.e., it is necessary only in the event that radioactive products are released from the reactor, and there are many other safeguards to pre- vent this release even if the containment is ruptured. At the present time, nuclear power plants must be located near large sources of water for cooling the steam generated. The construction of an industrial facility of any kind on the coast line is esthetically distasteful to most people since, unfortunately, there is not enough coast to fulfill all the needs and all the desires of all the people. In most cases where industrial facilities encroach on the lives of citizens, there is no mechanism other than zoning laws by which a person can effectively protest. But in the case of a nuclear facility, the public hearing required by the Atomic Energy Commission provides a forum for dissent, as in recent case histories, and the question of safety provides objectors with a weapon for fighting the construction of the plant. The nature of a public hearing for a nuclear plant is such that the prospective owner and operator must prove that there is no undue hazard, whereas the objectors need only demonstrate that there is a reasonable doubt. It is in this situation that geology becomes the Achilles Heel of nuclear power plant location. For his investigation, the geologist has natural exposures of rock at the ground surface and a limited number of trenches and drill holes to give him a fairly complete picture of the distribution of the various rock types. From the surficial data, he must infer three more dimensions — depth below the surface, past time, and future time. Unlike many problems faced by engineers, the geologist has only this one set of data from which to reach a conclusion — he is unable to reproduce the natural sequence of events in order to obtain another set of data for comparison. Hence, by the very deductive nature of a geologic conclusion, it is difficult to prove a geologic conclusion beyond a reasonable doubt even to other geologists — and perhaps one should say especially to other geologists because the experience and background of a geologist will strongly influence his conclusion, and no two geologists have exactly the same experience and training. The engineer and the public official would like the geologist to conclude that faulting cannot occur at a given site or to assign a numerical value to the probability of its occurrence — but no responsible geologist can do either of these things. Since government officials and others must make decisions that affect the public safety, it would seem that the geologic profession must attempt to establish criteria and

Jan 1, 1968

By J. E. Flinn, S. A. Duran

The steady-state creep behavior of poly crystalline cad mi inn was studied over a temperature range of (1.56 to 0.94 Tm. Two distinct mechanisms were found to occur over this temperature range. They were described by: where and represerqt the minimum strain rates corresponding to the low- and high-temperature regions, respectirely. The two regions of constant acti11ation energy were connected by a transition region where the strain rate was controlled by both mechanisms acting in parallel. At temperatures below a transition temperature of about 0.7 Tm the agreement between the activation energy value for creep and that for self-diffiision suggests a rate-controlling mechanism of dislocation climb. For cadwzium, steady-state creep at temperatures above 0. 7 Tm appears to be controlled by another mechanism, perhaps involving the behavior of dislocation jogs. FRENKEL et al.1 studied the high-temperature creep of polycrystalline cadmium and reported an activation energy of 21 kcal per mole for the 0.5 Tm < T < 0.8 Tm range. Based on observations of creep rate at only two temperatures, a value of 22.1 kcal per mole was determined by Medbury. These two investigations were for the purpose of showing agreement between the activation energy for creep and that for self-diffusion, reported3 as 18.2 and 19.1 kcal per mole, respectively, for diffusion parallel and perpendicular to the hexagonal axis. Gilman4 investigated prismatic glide in single crystals of cadmium over a higher-temperature range of 0.72 to 0.93 Tm, and found an activation energy of 29 kcal per mole. He also reported5 an activation energy higher than that of self-diffusion for prismatic glide in zinc single crystals deformed at temperatures near the melting point. This value was in good agreement with those found for an equivalent temperature range by Flinn and Munson6 and by Tegart and sherby7 for polycrystalline zinc. These two independent studies also disclosed at lower temperatures another value of activation energy near that for self-diffusion. It would be expected from the creep results on zinc and single-crystal cadmium that creep studies on polycrystalline cadmium, extended to temperatures near the melting point, might yield an activation-energy value higher than the 22 kcal per mole value found in earlier studies. The purpose of this paper is to report the steady-creep behavior of polycrystalline cadmium over a temperature range of approximately 0.5 to 0.9 Tm EXPERIMENTAL METHOD The cadmium used in this study was obtained in the form of as-cast rods, 0.5 in. diam, through the courtesy of the Bunker Hill Mining Co. The material was of 99.995 pct purity, as determined by spectro-chemical analysis. The creep specimens, which were 0.250 in. diam by 0.400 in. long and annealed at 300°C for 45 min to produce a stable average grain diameter 0.25 mm, were tested in compression using an apparatus similar to that described by Sherby.8 The specimen temperature was controlled to within ±0.5°C with the help of appropriate constant-temperature baths. The applied stress was maintained within 1.0 pct of the desired value by the additions of lead shot at fixed strain increments. No barreling was observed over the strains encountered during testing. Isothermal creep tests9 were used in the study with only a few differential temperature tests10 run for comparison purposes. Steady-state creep data were obtained over a temperature range of 60 to 287°C (0.56 to 0.94 Tm) at five stress levels ranging from 28.1 to 140.6 kg per sq cm. RESULTS The minimum or steady-state creep rate may be described by an equation of the following form:" where i is the minimum strain rate, S is the structure factor, F is a stress function, Qc is the energy of activation, T is the absolute temperature, and R is the gas constant. The minimum strain rates obtained in this study for cadmium were recorded on a semilogarithm plot as a function of the reciprocal absolute temperatures for the various stress levels, as shown in Fig. 1. This figure shows a characteristic transitional behavior" with a parallel interaction of two mechanisms. It is obvious that the activation energies corresponding to the individual processes are insensitive to stress because the curves are parallel. The discrete activation-energies values for the low- and high-temperature regions for the various stress levels are reported in Table I, and were determined by the least-mean-square method. For the low-temperature region, an activation energy of 20.7 ± 0.6 kcal per mole was obtained, and for the

Jan 1, 1967

By Alexander L. Field

The Bureau of Mines is investigating the problem of slag viscosity, its variation with the temperature and with the composition of the slag, and its effect upon the distribution of the sulphur between molten iron and slag, as introductory to a series of contributions to the theory of the metallurgical processes. The method of measurement, viscosity apparatus, furnace and other accessories mentioned in this paper have been described fully in s Bureau of Mines report.1 The Literature on Slag Viscosity The viscosity of blast-furnace slag had not been measured previous to the investigation described in this report. A number of investigators have determined the "fusibility," or softening temperature, of slags by means of the cone method .or other deformation method, but these methods supply only limited information regarding the temperature-viscosity relations of the slag in question. Any deformation method that may be employed indicates only the temperature at which the slag attains a more or less definite viscosity., the magnitude of the value obtained depending on the method used. For details of the various methods used by different investigators, see the Bureau of Mines paper already referred to. An isolated measurement by Doelter on a single mixture at 1,300" C. represents the highest temperature reached in the various viscosity investigations previous to those described in this report, in which results have been referred to absolute units. Arbitrary deformation tests have of course been made at much higher temperatures.

Jan 1, 1917

several days before leaving Buffalo; influenza developed, and when his train reached Nashville, Tenn., he was too ill to continue his journey and was taken to the Kissam Hall Hospital, Vanderbilt University, where he died of pneumonia. He was a young man of unusual ability and high moral character, always brigh.t, happy and kind, faithful and honorable in all things; loved by both his associates and those under his authority. His life and character cannot be better described than by the following quotation from one of his superior officers: "Lieutenant Ohnsorg was a man loved by all of us, always cheerful, just and kind, with unusual executive ability. We can never expect to find a man who has his ability and fine temperament and his position can never be sled as he filled it." He was happily married and leaves to mourn his loss a wife, Constance E. (Rogers) Ohnsorg and a baby girl born since his death, Nov. 29, 1918, a father, W. H. Ohnsorg, mother, Ida May Ohnsorg, and a sister, Mrs. Stuart Strathy McNair. He was a member of the American Institute of Mining Engineers and of the Florida Phosphate Miners&apos; Association. Lieutenant Edward Hale Perry At the height of the first great German&apos;offensive -of&apos;the Spring of 1918, Edward Hale Perry, of Boston, First Lieutenant, Company D, Sixth Regiment Engineers, U. S. Army, was killed on March 30, near War fusee—Aban-court, Picardy, France, while defending the Boisdes Tailloux against the terrific plunge aimed at Amiens. Lieutenant Perry was born in Boston, Jan. 23, 1887, the son of Georgianna W. and the late Charles F. Perry. After completion of his college preparatory course, he travelled for a year in South America and Europe before entering Harvard with the class of 1910. It might have been regarded as the natural thing for Perry, upon graduation, to choose a path that would lead to a business or professional career at home, but there were in his character a solidity, a horror of sham, a contempt for the "soft" things, and a love-of the open which caused him to be attracted to a life of stern and sturdy reality. Accordingly, he entered the graduate mining school at Harvard, and received the degree of Mining Engineer in 1913. In the meantime, two summers spent in Western mining camps had at-

Jan 1, 1920

By Bruce F. Grant, Stefan F. Szasz

During 1947, a Sinclair research team was assigned to investigate thermal methods of oil recovery. The assignment was recommended by a survey of possible research approaches to increase the amount of oil that ultimately can be recovered from oil producing reservoirs. The use of heat to stimulate oil production rates by the melting of paraffin deposited in well bores can be traced back to within one or two decades of the drilling of the Drake well. The application of heat on a larger scale has been discussed by generations of oil producers. Shortly after the turn of the century, one intrepid operator is reported to have injected steam into a Pennsylvania property. After a few weeks, he apparently became discouraged and terminated his experiment. Subsequently, the literature contains references to several well-developed techniques for supplying heat to a producing well bore to melt paraffin or to reduce the viscosity of oil contained in the formation immediately around the well bore.1.?.3.4 Some early references discuss procedures to furnish heat to the reservoir,5,6 with the injection well as the heat source, thus obligating the process to maintain the entire rock mass at a temperature above that at which the desired improvement in oil recovery would occur. Another approach to reservoir heating was reported by a group of Russian technologists in 1935.7,8,9 They definitely demonstrated that combustion can occur within the porous structure of an oil-bearing sandstone. Their field experiments, however, relied less on combustion within the rock than on heat furnished by combustion of oil supplied to the injection well bore. Ignition of the air-oil mixtures in the well bore was found very difficult, and the field tests were carried on for only short periods of time. Publication of the Russian work spurred at least one independent operator in this country to try firing an air-gas injection well, on for only short periods of time. Publication of the Russian work spurred at least one independent operator in this country to try firing an air-gas injection well. The Brundred Oil Corp. reportedly obtained combustion in the sand immediately around the injection well bore, but the experiment was abandoned because of interference with normal production schedules. Injection capacity of the experimental well was greatly reduced by firing. The well was reshot and pieces of sand showing partial fusing of the quartz matrix were recovered. To the authors&apos; knowledge no other field experiments utilizing combustion techniques for formation heating were undertaken prior to 1948, although the patent literature evidences continued interest in formation heating."&apos;," CONCEPT OF COMBUSTION-SUPPORTED HEAT WAVE The references cited were in agreement that heat applied to a reservoir would increase recovery, but there

Jan 1, 1955

By Arthur F. Wendt

The earliest knowledge of copper-ores in the Southwest was derived from the Mexicans, who, in the latter part of the last century, discovered and worked the Santa Rita copper mines, now situated

Jan 1, 1887

By Persifor Frazer

COMPARATIVE columns expressing the series of rocks of the lower half of the Mesozoic age in this country and in Europe are not yet definitely established. The following represents a co-ordination of the beds in England and Germany,* with a list of materials to be worked in from this country. † * Cotta, " Geologic der Gegenwart." † Section from York to Dillsburg. Report C, 1875; Second Geological Survey of Pennsylvania.

Jan 1, 1877

By D. E. Light, J. Y. Somnay

The use of alkyl acid phosphates and their alkali salts as collectors for the uranium minerals brannerite and uranothorite was investigated. In particular a detailed flotation study was carried out using isooctyl acid phosphate as a promoter. Tests were conducted on an Elliot Lake ore analyzing 0.11% U 3 O 8, chiefly as brannerite, and approximately 9% pyrite. Pyrite was floated with conventional reagents; the flotation of brannerite from the sulfide tails was studied to determine the optimum pH and pulp density to employ with isooctyl phosphate. 4 uranium recovery of over 90% was possible with a selectivity index of 8.95 when these tails were floated at 17% solids and a pH of 1.7. The effect of various modifying agents was also investigated. Aluminum sulfate, lactic acid and sodium silicate improved the selectivity of collection yielding selectivity indices of 9.5 to 11.5. Ferric chloride was found to be a depressant for brannerite. A Bancroft ore which analyzed 0.13% U308, and contained uranothorite was also amenable to flotation using isooctyl acid phosphate. The composite uranium concentrate obtained assayed 0.41% U308 at a recovery of 95.3% and a ratio of concentration of 3.24. Previous investigations1,2 on the flotation of brannerite, pitchblende, uraninite and/or uranothorite from various Canadian ores showed that fatty acids, including oleic acid and tall oils, petroleum sulfo-nates and alkyl acid phosphates, were suitable collectors for these uranium minerals. Additional work carried out by the Mines Branch in Ottawa on brannerite ores from the Elliot Lake area3 used the tall oil Acintol FA-1, or FA-2, as a collector. A recovery of 92% of the uranium in a concentrate which contained about 55% of the weight and assayed 0.2% U3O8 was obtained from a feed of 0.1% U308 in this latter instance. Eigeles et a1.4 carried out flotation on pitchblende ores and found that the most promising results were obtained with alkyl acid phosphates and their alkali salts as collectors. Within the homologous series of alkyl phosphates, the best flotation characteristics were displayed by isooctyl phosphates. Further, isooctyl phosphate derivatives were much less sensitive to hardness forming salts than oleic acid, enabling all flotation tests to be made with tap water. This paper describes tests employing alkyl acid phosphates for the flotation of ores containing brannerite and uranothorite. The flotation work described herein was conducted in conjunction with the development of a leaching process for Elliot Lake, Ontario, brannerite ores. In this process pyrite in the ore was concentrated by flotation and roasted, providing sulfur dioxide which was used to produce sulfuric acid in situ in a liquid-solid extraction process. A 40% conversion to sulfuric acid was indicated at a leaching temperature of 80°C; this resulted in the extraction of 93% of the total uranium after a contact period of 6 hr. A rotary kiln was used as a leaching vessel. Preconcentration by flotation was studied in conjunction with the above process to reduce the bulk of solids for leaching and, consequently, capital expenditure. The materials and methods used in this study will be described initially. Then the results will be presented in two sections, the first dealing with the brannerite ore, and the second with the uranothorite. Finally an economic analysis of the results on the brannerite material will be made. MATERIALS AND METHODS The two ore samples examined were from uranium-producing mines. One was a brannerite ore, a uraniferous quartz pebble conglomerate from the Elliot Lake area, which contained 0.11% U3O8, 4.3% S and 4.5% total Fe. Mineralogical studies of similar samples indicated the presence of quartz, microcline, sericite, pyrite and minor quantities of rutile, pyrrho-tite and zircon. The other ore was from a biotite-rich pegmatite in the Bancroft area; feldspar, quartz and biotite formed the major gangue components. Uranothorite was the principal uranium mineral; the head assay was 0.13% U 3 O 8. Preparation of Feed: The ores were crushed to —10

Jan 1, 1963

By W. S. Owen, A. R. Rosenfield

The measured changes in the yield stress of a poly crystalline Ta-O alloy after strain aging at 100°C have been separated into two components; the change inflow stress and the change in dislocation locking parameter. These two components vary independently indicating that at least two separate recovery processes take place during strain-aging. Variations in the locking parameter can be accounted for by segregation of oxygen atoms to dislocations, but variations inflow stress cannot be explained by current theories. STRAIN-AGING in Fe-C and Fe-N alloys has been studied extensively.&apos; The kinetics of the removal of the interstitial solute from solution appear to agree with the predictions of the cottrell-bilby2 model or a variation of it proposed by harper.3 Solute segregates to the dislocations under the influence of the elastic strain field of the dislocation and the rate of depletion of the solute can be measured by following the change in electrical resistivity4 or internal friction.5 On reloading a prestrained specimen, plastic flow starts at Fig. 1, but after aging the reloaded specimen yields discontinuously at a higher stress The aging index reflects the extent to which the yield has returned. Until recently it was usual to assume that ? is a result solely of the pinning of dislocations by the segregated solute atoms, that is, that op and oj coincide and the strain hardening curves AB and CD are continuous. Thomas

Jan 1, 1963

By G. W. Brownell, H. T. F. Lundberg, R. W. Pringle, K. I. Roulston

The rapid improvement of the airborne scintillometer and the perfection of its efficiency for counting low energy gamma radiation has made it possible to work out a technique to map in great detail the radiation pattern at the earth&apos;s surface. On such maps low radiation over certain areas appears to indicate the existence of oil accumulations, forming a pattern similar to that obtained by the geochemists.

Jan 12, 1953

By W. F. Hosford, E. W. Kelley

Deformation studies have been conducted at room temperature on single crystals of magnesium and magnesium alloys with thorium and with lithium. Single crystals oriented to suppress shear on the easily activated basal slip systems were deformed by plane-strain compression. Compression along the C axis was accommodated by {1011} banding. Compression perpendicular to the unconstrained c axis activated {1012} twinning, and, after virtually complete twinning, deformation continued by {1011) banding in the twinned material. Compression perpendicular to the constrained c axis was accommodated by the simultaneous operation of (1012) twinning against the constraint and (1011 ) banding. Although this orientation was favorable for {1010)(1210) prism and {1011}(1~10) pyramidal slip, these modes were not observed in pure magnesium or in Mg-0.5 pct Th. However, {10i0)(1~10) prism slip was observed in crystals of Mg-4 pct Li during compression perpendicular to the constrained c axis. Fracture in all materials occurred parallel to (1124) or {l~il) depending on the orientation and composition of the specimen. THE mechanical behavior of the hcp metals is strongly anisotropic. Although several slip systems have been reported the slip is cpmmonly in the directions of closest packing, the (1210),&apos; and this does not produce strains parallel to the c axis. Hence the inherent anisotropy. The deformation mode most easily activated in magnesium at room temperature is (0001)(1210)- basal slip. Also {1010}(1~10) prism slip and {1011)(1210) pyramidal slip have been reported, primarily at elevated temperatures.2"4 However, at room temperature the shear stresses to activate the prism and pyramidal modes are roughly a hundredfold greater than that required for basal slip.&apos;j4 Thus prism and pyramidal slip may be expected only under special conditions of loading. Strains normal to the basal plane can be produced by twinning, however. Many twinning modes have been reported for magnesium,&apos; with (1012) twinning the most common and relatively easy to activate. Magnesium can deform by (1012) twinning when stressed along the c axis jn tension, but not in compression. In contrast, (1011) twinning is activated by compression along the c axis and not by tension. In addition to primary twinning, secondary twinning or slip can occur within the reoriented material of primary twins.&apos; In general at least five independent shear systems must be active to bring about an arbitrary shape change such as that in the individual grains of a deforming polycrystalline material.&apos; Because basal slip can_ provide only two independent shear systems and (1012) twinning can only accommodate an extension of the c axis, other deformation modes must be active in magnesium for an arbitrary shape change to occur. The purpose of this investigation has therefore been to study the various deformation modes in magnesium at room temperature, with special emphasis on those modes that are less easily activated. The effect of the alloying elements, thorium and lithium, has also been investigated. In polycrystalline aggregates, unambiguous identification of deformation modes is extremely difficult and the direct evaluation of the resolved shear stresses to activate them is not feasible. On the other hand, uni-axial tension and compression experiments on single crystals may not activate some of the- deformation modes because basal slip and/or {1012) twinning cannot be suppressed in most orientations. However, it should be possible to activate all possible deformation modes using oriented single crystals and plane-strain compression. Identification of active deformation systems and evaluation of the resolved shear stresses required to activate them should be facilitated. Wonsiewicz and Backofen have recently completed an investigation of the plasticity of pure magnesium crystals at various temperatures utilizing plane-strain compression and selected crystal orientations. This technique has also been used in the present work. The seven orientations selected for study are indicated in Table I. Plane-strain compression along the c axis (orientations A and B) should activate some deformation mode _other than basal, prism, or pyramidal slip, or (1012) twinning. In orientations C and D, prism or pyramidal slip would be expected to take place. When the compressive load is applied perpendicular to an unconstrained c axis (orientations E and F) the three slip modes should be suppressed but not (10i2) twinning. In orientation G, basal slip should occur.

Jan 1, 1969

By E. F. Loiseau

IN a paper on the manufacture of artificial fuel, read at the Philadelphia meeting of February, 1878, I enumerated the difficulties which I had to overcome before succeeding in the mixing of coal-dust and clay, the compressing of the same mixture, and the water-proofing of the lumps. The drying of the lumps, after leaving the press, was the remaining difficulty, and it was expected that a plan devised by Dr. Charles M. Cresson, of Philadelphia, would enable us to dry the fuel as rapidly as it was moulded, and that a continuous production could in that way be obtained. The company was reorganized. The works were purchased by the new company at an assignee&apos;s sale, and the oven was modified, according to Dr. Cresson&apos;s plan. Anticipating a possible failure, I had prepared a plan by which I expected to be able to demonstrate that anthracite coal dust mixed with pitch, could be manufactured with our present machinery slightly modified ; so that after all, if we were compelled to give up the attempt to make fuel for domestic use, there was a possibility of succeeding in the manufacture of a good steam-fuel. The plan suggested by Dr. Cresson for drying the pressed lumps of coal-dust cemented with clay, did not work as well as we expected. It enabled us to dry more fuel than we did before, but it could not be made to dry more than one-half of the lumps produced by the press. The plan was abandoned, and I was authorized to experiment with coal-dust and coal-tar pitch. The cement which is used in Europe to conglomerate coal-dust is ,usually dry pitch, which is prepared by separating from the tar, at a temperature of 572° Fahrenheit, the volatile matters which it contains. Some manufacturers, however, employ crude tar, others, a rich tar, which has been cleared of 25 per cent. of its volatile substances, by heating it to 392° Fahrenheit. But with common tar very weak fuels are obtained, which do not burn well, and give out a strong smell and a great deal of smoke ; it is also necessary to subject them to a baking process, in order to solidify them, and to eliminate the more volatile of the materials contained. This operation of course requires a special plant, the cost of which increases sensibly the price of manufacture, without counting the products

Jan 1, 1880

By Joachim J. Hauser

Experiments on latent hardening were peyformed by compressing single crystals along a direction perpendicular to the tension axis. The slope and length of easy glide in the tension test were found to depend only on prior deformation in the same slip plane. Prior deformation on a different slip plane changes the stress level of the resulting stress-strain curve. The yield points appearing upon reloading after prior extension and unloading were related to the end of easy glide. SEVERAL researchers have studied the latent hardening due to deformation of a crystal by slip on a slip System after prior deformation. These experiments can be divided into those in which the prior deformation was on the same plane as the subsequent and those in which the two deformation processes were in different planes. In the former category are the experiments of Buckley and Entwistle,1 Parker and washburn,2 and Haasen and Kelly.3 The latter case has not been studied systematically; it was the main purpose of this investigation to produce this type of latent hardening and explain the results in terms of the existing theories of work hardening. In general, tension producing slip on a certain slip system can be preceded by tension, transverse compression or longitudinal compression, each with predictable dislocation movement and intersection. The intersection of dislocations can lead to glissile or sessile jogs, Cottrell-Lomer locks and other sessile dislocations. The effect on the stress-strain curve could depend on which combination of the former mechanisms is operating. Haasen and Kelly3 have studied the yield points which occur in aluminum and nickel single crystals upon reloading after prior unloading in a tension experiment. They attributed this effect to the anchoring of dislocations occurring during unloading. As Cottrell and stokes4 have shown that dislocations cutting through the "forest" could only lead to reversible changes, they attributed the anchoring to the formation of sessile dislocations during unloading. However, different kinds of sessile dislocations could be formed during unloading, and it was the purpose of this experiment to determine whether Cottrell-Lomer locks are responsible for the yield effect and for the end of easy glide. The case where a longitudinal compression is followed by tension along the same axis is commonly referred to as a Bauschinger test. This type of effect was studied by Buckley and Entwistle1 on aluminum single crystals and by Parker and washburn2 on zinc single crystals. In such a test, the tension and the compression activate the same slip plane with opposite slip directions. The use of sideways compression in the present experiments permits the activation of different types of slip systems and the study of their effect on the easy glide region and on the transition between the elastic and easy glide region. The theory of seeger5 for the flow stress in fee materials is applied to explain the latent hardening. EXPERTMENTAL PROCEDURE All the single crystals used in this investigation had an axial orientation close to <210>, called the "0.5" orientation. This is the orientation for which the tensile axis is 45 deg from both the slip plane and the slip direction. The single crystals were grown from the melt under a helium atmosphere using milled graphite boats,=at a rate of 8.6 mm per min. The silver used in the experiment was 99.98 pct pure. The single crystals had a square cross section about 0.9 by 0.9 cm and a length of 14 cm. The orientation of the specimen was determined within ±2 deg by the Laue back-reflection method. The specimens were annealed at 940&apos; ± 2°C in a helium atmosphere for 24 hr and then furnace cooled over a period of 7 hr. The specimens were electropolished in a solution of 9 pct KCN in water. The specimens were tested in a soft-type tensile machine (the load is prescribed) up to 3 pct strain. The stress was increased continuously at approximately 30 g per mm2 per min. The strain was measured over a 5 cm gage length with a mechanical extensometer employing an optical lever. The strain and stress were measured with accuracies of i 2 X 10-5 and ± 2 g per mm2, respectively. The remainder of the stress-strain curve up to 20 pct strain was obtained in a hard-type tensile machine (the strain rate is prescribed). The strain and the stress were measured in that machine with an accuracy of ±2 pct. The compression tests were performed in the hard-type machine using accurately machined steel blocks without lubrication. The blocks were used so as to apply a uniform compression over a length of 13 cm. The strains were measured on the hard-type machine and with a micrometer.

Jan 1, 1962