Search Documents

By Jack Zhang, Yunguo Tang, Baodong Zhao

"Rare earth elements (REEs) have numerous key applications in both traditional and advanced technologies. A shortage of some critical REEs is expected due to the discrepancy between the REE abundance in REE deposits and the REE demand from the market. For example, Neodymium, Europium, Terbium, Dysprosium, Erbium and Yttrium are expected to be in short supply. REE recovery and separation from secondary resources such as uranium wastes, heavy mineral sands, and recycled materials can balance the shortfall in a cost effective way.The Saskatchewan Research Council (SRC) is engaged in the development and commercialization of complete REE recovery and separation technologies in Canada. One of SRC’s newest developments is the design and commissioning of a heavy rare earth (HREE) separation pilot plant. The pilot plant uses hundreds of stages of solvent extraction (SX) to produce high purity individual HREEs from both primary and secondary resources.This paper presents the design of an HREE recovery process for the particular case of uranium processing wastes. The separation results of a group separation are reported and discussed, as well as the issues and the challenges of the development, commissioning and operation of the continuous SX pilot plant.IntroductionSignificant amounts of strategic specialty heavy rare earth elements (HREEs) are found in uranium wastes in Saskatchewan. It estimated that about 47 tonne/a of heavy rare earth element oxides (HREO) including 27 tonne/a of Y2O3, plus 6 tonne/a of Sc2O3 are in the raffinate of every uranium mill for potential recovery. Since the HREEs are already in the raffinate, cost effective HREE production is promising in Saskatchewan.Selective precipitation including nutraulization, oxalate and double-salts precipitation, as well as sulfide precipitation, ion exchange (IX) and SX are commonly used technologies for the recovery and purification of REE solution. REE oxalate precipitation is an effective technology to remove Fe, Al, Ca, Si and other impurities by taking the advantages of the solubility difference between oxalates of REEs and impurities in acidic solution (Xu, 2005)."

Jan 1, 2017

By K. N. Subramanian

Previously reported work on total oxidative leaching of chalcopyrite concentrates ha s shown that high copper extractions are obtained at 210°C and 0.4 MPa oxygen pressure. A simple integrated flow sheet using pressure leaching, solution treatment involving precipitation with a calcium base, and electrowinning to produce wire-bar-quality copper is described. Reagent and energy requirements developed from this work indicate that the process could be attractive for small operations where a smelting-refining complex cannot be justified.

Jan 1, 1978

Agenda ?Trends in Wireless Technology ?Success and Opportunities ?Improving plants efficiency ?Improving plants reliability ?Improving plants safety and security ?Wireless Ecosystem ?Lessons Learnt / Recommendations Why Wireless? ?Lower cost (no wiring cost) ?Flexibility (no wire) ?Standards-compliant wireless devices major factor enabling growth:?Standard WLAN (IEEE 802.11)?Wireless field I/Os (IEEE 802.11, ISA100.11 and WirelessHART) ??Wireless adoption will become a milestone that will rival the introduction of Fieldbus and the distributed control system (DCS) in its importance.? ARC Advisory Group

May 1, 2009

By J. A. McLennan

Nickel laterite deposits are typically formed from tropically weathered mafic-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate ?optimum? SMU mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each SMU. The optimum mining elevation is the elevation where the lowest summed cost of ?accepting dilution? and ?wasting ore? occurs. The reported SMU dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation and the reported SMU lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum SMU mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Apr 1, 2005

By Chris Bennett, Glen Kosick

"Process modeling and equipment sizing procedures for SAG circuits has advanced significantly over the past two decades. However, no matter how exact the hardness tests, models and scale-up calculations, if the ore samples being used for design do not accurately represent the orebody then major design errors can be encountered. This paper will describe a hardness testing method for identiQing the power requirement profile of an orebody, to an extent that design errors due to poor sampling can be greatly reduced or avoided altogether. It will provide some insight into the magnitude of hardness variability that can be encountered in an orebody. Finally, the paper will preview how detailed hardness distribution data can be incorporated into mine block models, to optimize SAG circuit design for an orebody, both fi-om a capital investment and throughput point of view.INTRODUCTIONIt has long been known that many SAG/AG' circuits experience wide swings in throughput. These throughput variations are almost always of a magnitude not anticipated in the plant design; consequently, they are detrimental to the expected return on investment for the mining companies. It is clear that the throughput swings are mainly caused by changes in ore hardness. In 1993, in an attempt to address this problem, MinnovEX began investigating the possibility of using a small scale SAG test (2 kg charge) to predict SAG power requirements from drill core samples. The objectives of the small scale test were to enable mining companies to do many more SAG hardness tests than currently undertaken for a particular orebody. To make this possible, the SAG tests had to use a minimal amount of sample, be cost effective, and give acceptable accuracy in the prediction of SAG power. If this small scale SAG test proved accurate, then the high sampling frequency would yield results that approach the true hardness distribution of an orebody. This hardness distribution could then be used to derive the distribution and variability of specific energy required throughout the complete orebody. This specific energy (kWh/t) can be thought of as the power required to grind one tonne of ore per hour (kW/tph) to a specified size. Once the true distribution of power requirement throughout the whole orebody is understood, the grinding circuit design team can make an informed decision regarding the hardness value that is most appropriate for sizing the SAG equipment. Throughput losses due to hardness variation could be deliberately planned for or avoided altogether (a capital cost decision)."

Jan 1, 1999

Forward-Looking Statements Information set forth in this presentation may involve forward-looking statements under applicable securities laws. Forward looking statements are statements that relate to future, not past, events. In this context, forward-looking statements often address expected future business and financial performance, and often contain words such as "anticipate", "believe", "plan", "estimate", "expect", and "intend", statements that an action or event "may", "might", "could", "should", or "will" be taken or occur, or other similar expressions. Forward-looking statements or information relate to, among other things expected iron ore demand, timing for a production decision, expected share price drivers, potential railway options, timing, grade and quantity of potential resource estimates, employment and economic benefits, taxation estimates and timing of key project milestones. By their nature, forward-looking statements involve known and unknown risks, uncertainties and other factors which may cause our actual results, performance or achievements, or other future events, to be materially different from any future results, performance or achievements expressed or implied by such forward-looking statements. Such factors include, among others, the following risks: the risks associated with the need for additional financing; operational risks associated with exploration; fluctuations in commodity prices; title matters; environmental liability claims and insurance; reliance on key personnel and other risks and uncertainties discussed in the management discussion and analysis section of our interim and most recent annual financial statement or other reports and filings with the TSX Venture Exchange and applicable Canadian securities regulations. Forward-looking statements are made based on management's beliefs, estimates and opinions on the date that statements are made and the Company undertakes no obligation to update forward-looking statements if these beliefs, estimates and opinions or other circumstances should change, except as required by law. Investors are cautioned against attributing undue certainty to forward-looking statements. NI 43-101 Qualified Person Alderon?s exploration work on the Kami Project is supervised by Edward Lyons, P.Geo., the Chief Geologist for Alderon and a Qualified Person as defined byNational Instrument 43-101. Mr. Lyons has reviewed and is responsible for the technical information contained in this presentation. Mr. Lyons is a member in good standing of the Association of Professional Engineers and Geoscientists of British Columbia (APEGBC) and the Professional Engineers & Geoscientists Newfoundland & Labrador (PEGNL) as a registered Professional Geoscientist (P.Geo.).

May 1, 2011

By W. G. Campbell

"The region discussed comprises approximately eight million acres spreading across the Arctic Circle in Yukon and North West Territories.Encouraged by four years of surface geological and geophysical work, which strongly suggested that suit-able conditions existed for the entrapment of oil and gas, a decision was reached to drill. In due course two holes were drilled; Eagle Plains No. 1 drilled to 9589 in 1957-8 and Western Minerals Chance No. 1 spudded in 1959 is being deepened this year.Thick sections of sedimentary rocks occur on both sides of the Richardson Mountains, however, most of our activities have been concentrated to date on the west side in the Eagle Plains basin. Here are found stratigraphic units ranging from Precambrian to Tertiary age. The drilling of the two exploratory wells proved the presence of these strata at depth and have confirmed the presence of promising structures. A geological cross-section across Eagle Plains presents an interpretation of these conditions.Physical and engineering aspects of exploration in the northern Yukon and North West Territories are de-pendent largely upon seasons and transportation. Reconnaissance gravity and surface geologic mapping by air presents no serious problems. However, seismic operations on the ground are greatly affected by the season, presence of permafrost and mobility of equipment.The actual drilling of the hole may well be the simple part of a wildcat undertaking once equipment and supplies are on location. Over-all planning, assembling supplies, transporting equipment and personnel seems to be the real job. Serious consideration must be given to per-ma-frost effect in the drilling pro-gram and on surface installations as well.Programming for -the various exploration activities should be under-taken well in advance of the actual doing. Considerable extra costs may be the results of crash programs. Costs are high, and the rewards uncertain. Economic evaluation is based •on the long term outlook."

Jan 1, 1960

By L. R. Plitt

A series of experiments were carried out in an effort to develop a universally applicable mathematical model of the hydrocyclone classifier. The design and operating variables studied were: cyclone diameter and height, the inlet, vortex finder and apex diameters, the feed pressure and the solids content of the feed slurry. The model consists of four basic equations which express the cut size ( dso), volumetric split between overflow and underflow, volumetric throughput, and sharpness of separation in terms of the operating and design variables. Although empirical, the model is nevertheless in general agreement with fundamentally derived models. The model clearly 1•eveals the effect of the major variables on the operation of a hydrocyclone. Because of its broad data base and the inclusion of all the major variables, the model may be used without experimental data to predict the operation of cyclones over a wide range of different operating conditions. With operating data, the equations may be modified to serve as an operational model.

Jan 1, 1976

By D. A. Temple, G. O. John

Until recently, the approach to the problem of treating complex ores bas been to produce, insofar as is possible, mono-metal concentrates which are treated in traditional zinc, lead and copper smelting circuits, with the residues and by-products from some of these circuits being retreated for the recovery of contained values either by a separate residue treatment process or along with the primary feed to the appropriate circuit. The continued development of the Imperial Smelting Process, with its ability to treat poly-metal concentrates, calls for a re-examination of the traditional approach to this problem, and this the paper attempts to do. A survey of recent progress in the technical development of the process is made and a summary of current operational performance is included.

Jan 1, 1971

Experimental Mine, Val d'Or, Quebec, Experiments on the ignition of sulphide dust clouds by explosives have been conducted in a 1 m3 explosion chamber. The explosives tested are ANFO, emulsion, aluminized emulsion and Detasheet. By controlling the composition of the ANFO and the emulsion explosive the oxygen balance could be changed in order to identify the dominant factors in the ignition of sulphide dust clouds by explosives. Experimental results, combined with theoretical calculations, show that the temperature of the detonation products is the most important parameter in the ignition of the dust cloud while the combustible detonation products are of secondary importance in the case of non-aluminized mining explosives. In the case of aluminized explosives and explosives having very negative oxygen balance the ignition of the dust cloud is assisted by the large amount of combustible detonation products.

Jan 1, 1993

By C. M. Offenhauer

Abstract Zirconium markedly affects the formation of graphite in cast iron and may promote the formation of normal flake gaphite, fine flakes of eutectiform graphite, or spheroid nodular graphite, according to the composition of the Iron and the amount of the zirconium addition. Usually, it is employed in the form of a complex addition agent in order to facilitate its introduction and to guide its effect. The reported applications of zirconium as an inoculant for the production of pearlitic high-strength cast iron indicates that it is most effective as a silicon-manganese-zirconium alloy. Added in this form it reduces chill and minimizes zones of ferrite and eutectiform graphite. In low-sulphur cast iron, zirconium in amounts greater than 0.10 per cent tends to promote the development of eutectiform graphite. These irons are characterized by freedom from primary cementite or normal flake graphite and exhibit very little tendency to shrinkage on solidification. In hyper-eutectic low-sulphur cast iron, zirconium causes the formation of a partially nodular graphite structure. A combination of magnesium with silicon-zirconium alloy was found to produce completely nodular graphite structures without the hazards associated with the addition of elemental magnesium.

Jan 1, 1949

By Paul Krivokuca

Outline Quinsam Coal Mine ?? Location ?? Mine History ?? Safety ?? Production ?? Hiring 4S Mine ?? Depillaring design ?? Structural mapping, Risk assessment ?? Rock Bolt Design Selection ?? Training

May 1, 2008

By D. T. White

Pressure acid leaching of nickel laterite ores typically involves the production of an intermediate product that is releached and refined to pure nickel and cobalt products. BHP Billiton is developing the Ravensthorpe Nickel Project to produce up to 50,000 t/y of nickel via a mixed hydroxide intermediate, which will be refined at its Queensland Nickel (QNI) Yabulu Refinery near Townsville, Queensland. The hydroxide precipitation flowsheet has been adapted to process high magnesium ores through an atmospheric leach stage, eliminate iron(III) as jarosite and oxidise iron(II) during neutralisation. The neutralisation conditions are controlled to precipitate aluminium, chromium and silicon, and to ensure good solid-liquid separation. Soluble impurities such as magnesium are purged with the tailings stream and will be managed over the long term by crystallisation in evaporation ponds.

Jan 1, 2006

By L. E. Djingheuzian

"IntroductionIN 1940, in a series of articles, M. W. von Bernewitz(l) reviewed in detail roasting of gold and silver sulphide ores and concentrates. Since that time some significant developments in roasting have taken place, and a number of papers have appeared in the Canadian technical literature, dealing severally with the roasting of a particular ore or concentrate.The purpose of this paper is not only to review some of these Canadian papers and bring the information on Canadian roasting practices to .date, but also to analyse the mechanism of roasting. Hence, it is proposed to start with a study of physico-cl1emical factors fundamental in roasting, the knowledge of which, by creating a sound basis for a proper roaster design, makes good roasting possible.Physico-Chemical FactorsRoasting can be defined as heating sulphide ores in presence of air below fusion points of the constituent minerals, at such temperatures as to convert metallic sulphides to oxides. Hence, roasting is a chemical process.The object of roasting is, by changing, chemically, mineral constituents of sulphide ores, to make the economic recovery of the desired •Constituent metal by a subsequent standard treatment possible. For instance, pyritic ores, containing gold in sub-microscopic form which no amount of grinding would release, are roasted in order, by oxidizing the sulphides, to open up their structures to such an extent as to enable cyanide solutions to come into contact with the gold and dissolve it. The production of porous calcine is, therefore, the object of roasting of refractory auriferous sulphide ores or concentrates. Such a porous calcine may be defined as a desirable calcine, and the roasts which produce desirable calcines can in their turn be termed desirable roasts."

Jan 1, 1952

By E. M. Watkin

"Although Canada has achieved one of the highest living standards in the world, people and organizations have, over the past decade, begun to question the cost and means of this achievement. Concern has been expressed about the degree of environmental disturbance arising from industrial activities which have greatly contributed to our increased living standards. These industries include hardrock mining, pit and quarry operations, hydro-electric schemes, various agricultural enterprises and urban land developments.In the construction and operation of the above industries many environmental problems arise because the natural vegetative land cover is destroyed or drastically disturbed. Disturbance may occur to such a degree that revegetation is di ffi cult, often it appears impossible. Portions of the environment around such industries remain aesthetically unacceptable and appear to offer little or no potential for future resource use in wildlife, recreation or agriculture.The general public cannot dissociate itself from the activities of the aforementioned industries. It has, over many years, accepted the benefits and conveniences arising from those activities. Despite this, the increasing level of public concern imposes upon industry a need to alleviate or repair past, present and future environmental disturbance. Therefore it is incumbent upon industry to modify present technology or develop new techniques which would allow the disturbed environment to be easily and rapidly repaired."

Jan 1, 1975

By Longjiang Li, Song Mao, Zhengyang Qiao, Qin Zhang, Guizhou University, Ling Wang

"After a study on the advantages and disadvantages of flotation column, according to the limitation of ordinary flotation column only is used for a flotation of microgranular minerals, the paper designed a new kind of layered convection coarse particle flotation column.Using a bauxite to test the rationality of the flotation column.The test results show that the new layered convection coarse particle flotation column is feasible.It has certain advantages about coarse particles flotation.INTRODUCTIONFlotation column has many advantages, for example,a simple structure, high efficiency and energy saving, the obvious advantage of fine particles flotation , the index superior and so on. The advantages gradually getting people's recognition. Research of flotation column has been a breakthrough, however, due to it only is used for the flotation of microgranular minerals, and the microgranular mineral particles will lead to a series of problems, and makes the processing cost is increased. Due to increase grinding fineness can save the grinding time and reduce the cost of grinding, also can avoid the disadvantage of fairly granular mineral particles cause a deterioration in the flotation. So it is necessary to research a kind of coarse particle flotation column.After a research on the advantages and disadvantages of flotation column, the authors designed and manufactured a new layered convection coarse particle flotation column, the flotation column both in theory and operation is better than flotation machine.DESIGN OF THE LAYERED CONVECTION COARSE PARTICLE FLOTATION COLUMNAdvantages and Disadvantages of the Traditional Flotation ColumnIn the field of mineral processing, as the increasing proportion of ore that has low grade, fine dissemination size, complex mineral composition characteristics. The limitations of traditional flotation machine is increasing[1],for instance, the high energy consumption, severe wear, inconvenient configuration , large amount of maintenance and so on. Compared with flotation machine, the flotation column with high separation efficiency, low investment and production cost, covers a less area low installation cost, less reagent dosage, more suitable for separation of fine particles and can automatically control, etc[2]. At present, the ore is facing the world energy crisis situation, and becoming increasingly difficult to flotation. So it is important to invent a coarse particle flotation column."

Jan 1, 2016

By D. Fleury

"This paper describes the challenges of mining a sill pillar under various types of paste backfill quality. From 1994 to 2002, Louvicourt mine produced approximately 12,600,000 t grading 3.5% Cu, 1.5% Zn, 27 g/mt Ag, and 0.85 g/mt Au. The mining method is transverse blasthole stoping, mining primary and secondary stopes. The production of this 4,300 t/d operation was accomplished using two mining horizons; from the 655 m level to the 415 m level and from the 860 m level to the 680 m level. The main sill pillar is between the 680 m level and the 655 m level. The second sill pillar is between the 885 m level and the 860 m level representing a quarter of the main sill pillar in size. Since 2002, production has gradually decreased and mining activities are expected to end in mid-2005. The sill pillar production will represent almost 25% of the total mine production. The overall recovery of the sill pillars stopes will be discussed in this paper. To recover the sill pillars, more than 1,500 m of development was planned in or under paste backfill. The first sill pillar stopes under paste backfill were mined out in 2002 with excellent results."

Jan 1, 2005

By Brigitte Lacouture, Yeen Shien Hwang, David Lin

"A baseline survey of the partially open lead regrind circuit at Red Dog Mine indicated poor regrind efficiencies for the three parallel 450 HP tower mills. Driven by the high energy cost and the potential metallurgical gain brought by improved mineral liberation, the Red Dog lead regrind circuit was optimized in two stages.In the first optimization stage, different circuit layouts were evaluated in two plant trials. In June 2003, the regrind circuit was changed to a fully closed circuit. This reduced the tower mill requirement from three to two mills. The circuit modification payback was 11 days through power savings alone.The second stage of optimization was the evaluation of reagent addition. To improve pyrite depression, sodium cyanide was added to the feed of the lead regrind tower mills and tested in a series of plant trials over several mill feed stockpiles. Galena selectivity against pyrite was found to improve in these plant trials. Due to environmental sensitivities, no net increase in cyanide addition to the plant occurred and thus no increase in the cyanide concentrations in the tailings pond or the environment will result.The lead regrind optimization work improved the overall lead metallurgical performance and reduced energy and reagent costs. Economic analysis showed that annual profit increased by as much as US$3.0 M."

Jan 1, 2005

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By Filip Rochette, Yvan De Busscher

Extraction of minerals can be achieved by a variety of technologies; one of them is ion exchange. There are several ion exchange configurations and mechanical set-ups available, but only one technology will provide more process performance and flexibility compared to the other. The multiple column Continuous Countercurrent Ion Exchange (CCIX) technology provides the highest form of process flexibility with also the highest mineral recovery feasible through ion exchange. In comparison with a fixed bed system, the PuriTech CCIX system offers the benefits of continuous counter-current contact mode. This way the resin capacity is fully exploited leading to reduction in resin inventory and, at the same time, in chemicals and water consumption, and product dilution. For any set of operating conditions the mass transfer zone has a characteristic length (MTZL). The MTZL can be expressed in duration, column length, or volume, but is the measure of the quantity of resin in the system that is doing "work" at any given moment in the process. The objective of continuous ion exchange processing is to eliminate all resin volume from the process equipment that is not within a mass transfer zone. In most commercial ion exchange processes for the recovery of metals, CCIX engineering can eliminate as much as 20 - 80 % of the ion exchange resin inventory. Consumptions of water and chemicals are typically brought down around 40% or more. For each type of resin the selectivity/affinity towards a particular metal depends on the basic process conditions such as pH, concentrations of other competing metals in solution. By changing the pH in the ion exchange process phase, the selectivity of the resin can be changed. By doing this, a split elution, or extraction of metals separately can be achieved and the effect of other competing metals (cross-contamination) can be reduced. For example the DOW resin XUS43578 is commonly used for the recovery of copper or nickel/cobalt separation.

Jan 1, 2016