Search Documents

By S. R. McCutcheon, D. R. Lentz, W. S. Downey

"Abstract - The Little Falls member of the Nepisiguit Falls Formation is situated in the northern part of the Brunswick Belt of the Bathurst Mining Camp and has been interpreted as the distal equivalent of proximal tuffaceous rocks that host the stratiform Brunswick No. 12 and No. 6 Pb-Zn massive sulfide deposits. It comprises fine-grained, greenish-gray tuffaceous sandstone in the lower part, and coarse-grained, crystal-rich tuffaceous sandstone in the upper part. Petrographic evidence suggests that these rocks have a turbiditic origin. The Little Falls member is underlain by the Vallée Lourdes member, mainly composed of relatively shallow-water calcareous rocks, and is conformably overlain by Mn-rich sedimentary rocks, mainly red argillites that host the Tetagouche Falls Mn-(Fe) deposit. All these rocks are considered to belong to the Nepisiguit Falls Formation, part of the Ordovician Tetagouche Group. Whole-rock geochemical data from the fine-grained tuffaceous sandstone and coarse-grained tuffaceous sandstone indicate that the two units of the Little Falls member are distinct. Zr and TiO2 contents, and total rare earth element (REE) values are higher in the coarse-grained unit (average Zr/TiO2 = 0.040, average SREE = 247 ppm, n = 6) than in the fine-grained unit (average Zr/TiO2 = 0.048, average SREE = 158 ppm, n = 17), which can be attributed to the variation in crystal content between the two units. Both units are HREE-enriched and have elevated La/Yb relative to the typical Nepisiguit Falls Formation. Overall, the geochemical data combined with evidence from the bounding units suggest that the Little Falls member was deposited in relatively shallow water, possibly in a near-arc environment. The relationship of volcanic facies within the Nepisiguit Falls Formation and the geochemistry of these facies indicate strongly that fine grained, reworked tuffaceous rocks, regardless of whether they are the distal equivalents of proximal tuffaceous rocks, are not associated with the major ore-bearing horizons of the Bathurst Mining Camp. Sommaire - Le Membre de Little Falls de la Formation de Nepisiguit Falls se retrouve dans la partie nord de la Ceinture Brunswick du Camp Minier de Bathurst ou elle a été interprétée comme l’équivalent distal des roches tuffacées proximales hôtes des gisements de sulfures massifs de Pb-Zn stratiformes Brunswick No.12 et No.6. Il consiste en grès tuffacé à grains fins gris verdâtre dans sa partie inférieure et en grès tuffacé à grains grossiers riche en cristaux dans sa partie supérieure. Les données pétrographiques suggèrent que ces roches ont été déposées par des courants de turbidité. Le Membre de Little Falls repose sur le Membre de Vallée Lourdes, lequel consiste principalement en roches calcareuses déposées en eau relativement peu profonde; il est de plus recouvert en concordance par des roches sédimentaires manganifères, lesquelles consistent principalement en argilites rouges hôtes du gisement de Mn-(Fe) de Tetagouche Falls. Toutes ces roches appartiennent à la Formation de Nepisiguit Falls, laquelle fait partie du Groupe de Tetagouche, d’âge Ordovicien. Les données lithogéochimiques des grès tuffacés à grains fins et à grains grossiers indiquent que ces deux unités du Membre de Little Falls sont distinctes. Les teneurs en Zr et en TiO2, ainsi que la teneur totale en Éléments des Terres Rares (ÉTR) sont plus élevées dans l’unité à grains grossiers (Zr/TiO2 moyen = 0.040, SREE moyen = 247 ppm, n = 6) que dans l’unité à grains fins (Zr/TiO2 moyen = 0.048, SREE moyen = 158 ppm, n = 17), ce qui pourrait s’expliquer par la variation de la quantité de cristaux dans chacune de ces deux unités. Chacune de ces deux unités présente un enrichissement en ÉTRL ainsi qu’un rapport La/Yb relativement plus grand que ce qui est typiquement observé dans la Formation de Nepisiguit Falls. Les données géochimiques considérées conjointement à l’information provenant des unités adjacentes suggèrent que le Me"

Jan 1, 2006

By A. Tabereaux

The reduction of perfluorocarbon (PFC) emissions from aluminum electrolytic cells is a key issue in reducing greenhouse gases at all aluminum smelters, The emission of tetrafluoromethane (CF4) and hexafluoroethane (C2F6) gases during anode effects at smelters can be calculated using two different methods; anode effect-minutes slope and anode effect overvoltage, This work demonstrates that the optimum method depends to a large extent on the type of anode effect kill algorithm utilized at each smelter, CF4 emissions vary widely from aluminum cells depending on the type of anode effect kill method utilized; fast, aggressive anode bridge movements vs. slower, moderate anode bridge movements.

Jan 1, 2005

By E. Brouillette

Difficult operating and mining conditions such as low visibility, difficult roadbeds, fast cycling, small openings, and sharp corners create high demand for LHD manoeuvrability and operator dexterity. Operator experience and patience is especially solicited to fill the bucket rapidly and efficiently and performance can be particularly affected by the skill level of individual operators. Teleoperation and automated loading are viewed as options to improve overall equipment and operation performance in certain mining conditions. Comparative statistical measurements of autoloading performance in different production environments at Noranda demonstrate an increase in bucket filling efficiency and a reduction in filling variance, allowing LHD operation to be more consistent and within manufacturer specifications. Consequential cost savings and productivity increases are demonstrated to be transferable to other mining situations.

May 1, 2003

By James F. Kelly

"Research and development on the production of liquid fuels from coal is rapidly expanding worldwide. AImost every industrialized country is engaged in coal liquefaction research and process development. In Canada, the federal government, through CANMET, is actively supporting coal liquefaction research and development in a number of areas.A review of the basic principles and some of the processes in the production of liquid fuels from coal is presented with reference to the characteristics of the Canadian coal resource base. An overview of the CANMET coal liquefaction contract program is presented and specific results from the batch autoclave studies carried out with Saskatchewan lignite and Nova Scotia high-volatile bituminous coals are discussed. The development of a laboratory-scale continuous-flow coal liquefaction unit at the Energy Research Laboratories of CANMET to investigate the co-processing of coal and bitumen/heavy oil is also described.IntroductionThe CANMET coal liquefaction program is made up of two interrelated parts. The first part consists of the research and development work being carried out at the Energy Research Laboratories near Ottawa, Ontario. The second focuses on contracted research and development as part of the Coal Conversion Program of Energy, Mines and Resources Canada. The long-term objective of the liquefaction program is to contribute to Canadian liquid fuels production through the definition, research, development and demonstration of different coal liquefaction technologies for the Canadian marketplace.In coal liquefaction, the main objective is to produce liquid hydrocarbons with a higher hydrogen-to-carbon (HIC) ratio than the coal feedstock while reducing heteroatom (S,O,N) content, removing mineral matter and minimizing gas production. Typical atomic HIC ratios for a variety of Canadian fossil fuels are shown in Figure I. Canadian coals have about 500/0 of the HIC ratio present in tar sand bitumens and heavy oils and only about 20% of the ratio available in methane. In general, the cost of synthetic fuels production is related to the cost of hydrogen and, therefore, to the increase of HIC ratio between feedstock and products. On this basis, the production of liquid fuels from coal would be expected to be more costly than liquid fuels produced from bitumens and heavy oils. However, for mined tar sands and some heavy oils this difference tends to be offset by the large sand content (>90 mass %) of tar sand bitumens and the increased production costs of viscous heavy oils. For example, it can easily be shown that for equal weights of distillate <525°C) yield, current coal liquefaction processes required between two and three times less mined coal by weight than the mined tar sand s required for the most technically advanced processes proposed for bitumen upgrading."

Jan 1, 1981

By T. Yalcin

"This paper describes a study carried out to determine the behaviour of Cu-Ni mill tailings during natural and flocculated sedimentations. Settling rates were examined under various conditions through standard laboratory batch settling tests. Flocculation was found to improve the sedimentation process significantly, but its effectiveness depended on several factors such as the pulp density of feed, the type and dosage of flocculating reagent, the pH of pulp, the intensity of mixing flocculant with tailings sand the use of stirring during compaction.It is shown that. for a sedimentation process taking place under given conditions, underflow pulp density (P) and sedimentation time (t) are related by the expression P = k.tn, where k and n are constants. A procedure is described for the use of this expression in thickener size estimations. IntroductionOften a considerable proportion of the mill feed is disposed as tailing, because the valuable mineral recovered usually forms a small fraction of the ore. Moreover, wet concentration processes result in liquid wastes that are several times more voluminous than the ore itself. Thus the handling and disposal of these wastes become an important cost item in most milling operations. The principal unit process employed in tailing disposal is solid-liquid separation which is traditionally carried out by gravity sedimentation in thickeners or tailing dams. Direct disposal of tailings into tailing dams is common practice where sufficiently large areas of land are available but it frequently becomes more economical or practical to densify the tailings in a thickener beforehand.Successful thickener operation depends essentially on correct thickener size which is in turn governed by the sedimentation characteristics of the tailings handled. Flocculation can aid the sedimentation process and bring about significant savings in thickener size, but its effective use requires a detailed study to identify the optimum conditions of application."

Jan 1, 1988

By D. Kong, A. Klyashtorin, L. McGilp, I. Wilson

This work reports on applying iron oxide coated sands media in an experimental permeable reactive barrier to remove uranium species from uranium containing water. A field experiment was conducted at the legacy Gunnar uranium mine & mill site that was abandoned in the 1960s with limited to no decommissioning. The flooded Gunnar mine pit presently contains about 3.2 million m3 of water contaminated by dissolved U (1.2 mg/l), Ra-226 (0.4 Bq/l), and minor concentrations of other contaminants (As, Se, etc.). The water is seeping over the pit rim into Lake Athabasca posing environmental and health concerns. Iron oxide coated sands can be used to immobilize uranium species through an adsorption process. Methods for preparation of hydrous ferric oxide sorbents and their supported forms onto silica sands are described. Fourier transform infrared spectroscopy (FTIR), and powder X-ray diffraction (pXRD) were used to characterize the physical-chemical properties of the sorbent. The monolayer uranium uptake capacity (Qm) was estimated through the Langmuir adsorption isotherm. Adsorption kinetic experiments were performed in a lab environment before moving to a field trial. Based on these lab results and the input on field-scale appropriate geometries, a pilot permeable reactive barrier was fabricated and a field test conducted near the Gunnar pit in June 2019. This pilot test provided technical data and information needed for designing a full-scale permeable barrier based on the iron oxide coated sands, which may be applied for in-situ water treatment at Gunnar and other legacy uranium sites.

Jan 1, 2020

By B. J. McKay, K. Schneider, H. B. Nadendla

"A series of experiments were conducted to assess the impact of zinc additions on the morphology and soundness of the interface of Al-Mg compound castings. It was found that high amounts of zinc (>15wt%) are necessary to affect the morphology and microstructure of the interface. At these zinc concentration levels, the formation of the zinc-rich phases t1 and ? were observed along with the Al-Mg intermetallic phases ß and ?. The micro hardness of all phases across the interface was found to be similar, ~200 Hv. This even hardness gradient is thought to avoid mechanical failure in the interface under load. In samples containing large concentrations of zinc (>15wt%), the formation of bubble shaped voids as well as the complete transformation of the aluminium alloy was observed. While the exact mechanism causing the voids has not been identified it thought to be connected to the Kirkendall effect. INTRODUCTION Conventional single material components are increasingly failing to meet the demands, in terms of cost and performance, of the transport industry. Compound castings have been identified as a promising alternative as they possess a number of benefits (Bührig-Polaczek, Röth, Baumeister, Nowack, & Sussmann, 2006). Compound casting is described as a process in which a metallic melt is cast around a solid metal shape. Preliminary research has concluded that for the stability of such a resultant hybrid structure it is imperative that both metals form a sound connection via form closure, force closure, or material bonding. A continuous material bond between the two metals is also highly desirable as the formation of a crevice between the metals could lead to galvanic corrosion, particular in a humid environment (Lao, 2013; Rübner, Günzl, Körner, & Singer, 2011). Even though Al-Mg compound castings could offer the biggest potential in terms of weight savings to date only a limited amount of research concerning such structures exists."

Jan 1, 2018

By Ramin ArameshAsl

Urumieh-Dokhtar is the well-known vast metallogenic belt extended from NW to SE of Iran and basically is referenced in copper mineralization studies in Iran. Hashtjin 1:100000 sheet (NW Iran) is located on this belt and rock units are consisted of Oligocene intrusive, volcanic rocks and Eocene Sedimentary rocks. Concerning the significance of identifying the alterations and faults zones in copper exploration, the aim of this study is identifying the copper mineralization by multi-spectral analysis of ASTER (Advanced Space borne, Thermal Emission and Reflection Radiometer) satellite images in the limitation SD-SWIR (Spectral Domain of Short Wave Infrared). Several analytical methods are implemented in this study such as SAM (Spectral Angle Mapper), MF (Matched Filtering) and PCA (Principal Components Analysis). These methods have been utilized for recognizing the Argillic, Propylitic and Sericitic alteration zones and all of them are relying on the remote sensing methods as well as geological studies of new targets for copper mineralization identification in the area.

Aug 1, 2013

By V. Labiouse, F. Orellana

"Hollow cylinder samples can be tested for both the characterization of rock properties and the physical modelling at reduced scale of engineering applications. Particularly, this type of experimental setup can be used to simulate different stress conditions around underground openings, as already developed in the petroleum engineering field e.g. to study the instabilities around deep wellbores during either drilling or the oil production phase. Some authors have also used this technique to successfully characterize the damaged zone around underground openings in the tunneling engineering field looking for an efficient design of their support.This article presents a new hollow cylinder testing device developed at the Rock Mechanics Laboratory of the Ecole Polytechnique Fédérale de Lausanne (EPFL), Switzerland. It allows a full and independent control of the confining pressure and pore water pressure conditions at both the inner and outer boundaries of Thick-Walled Hollow Cylindrical samples. In order to mimicking a tunnel excavation in a porous rock mass, after initial recovery of the in-situ stress and pore water pressure, the hollow cylinders are subjected to a decrease in the internal confining pressure. Moreover, X-Ray Computed Tomography scans of the specimens are performed through the testing cell before and after the mechanical unloading to monitor the displacements undergone and the sample damage. The equipment, testing procedure and data analysis techniques are briefly presented in the paper.The good performance of the apparatus has already been checked on weak rock specimens, among others on Boom and Opalinus Clay samples. In many configurations, the mechanical unloading is found to induce a Damaged Zone (DZ) around the central hole. Its geometry and extent show a great similarity with in-situ observations around tunnels driven in the Boom and Opalinus Clay formations. Such similarities contribute to increase confidence in the understanding and modelling of the ongoing processes."

Jan 1, 2015

By L. Szecowka, M. Poskart, Siwka M. . J.

Oxides of nitrogen, created during combustion, are the most hazardous components of atmospheric pollution. However, it is possible to limit the negative influence of hazardous components on the natural environment. An experimental appartatus was built to determine the influence of the following "primary methods" on the reduction in concentration of NOx: air staging, reburning and flue gas recirculation. The influence of the simultaneous usage of the primary methods on reduction in NOx emissions was also examined. A significant increase in the efficiency of NOx reduction was achieved in two cases.

Jan 1, 2004

By P. Zhang, K. Liu, L. Ou

"The strength and mechanism of Portland cement prepared from stone coal vanadium slag were studied in this paper. Initially, the slag was used as silicon raw materials to prepare clinker. By blending the prepared clinker with gypsum, waste, and fly ash, a series of different grades cement got well prepared. All of performances of the cement were up to the requirements of China’s national standard. The hydration products and microstructure of cement were identified and analyzed by X-ray diffraction and scanning electron microscopy. With the comparison of cement hydration characteristics at different ages, the strength formation mechanism of cement was clarified. The experimental results suggested that adding the fine materials (mainly waste and fly ash) to replace part of clinker would accelerate cement hydration, as it provided additional surfaces for the nucleation and growth of hydration products. And the hydration products were similar to ordinary Portland cement, mainly containing the amorphous calcium silicate hydrates (C-S-H), acicular ettringite (AFt) and portlandite (CH). With hydration time increasing, the hydration products continuously covered the cement particles, resulting in a thicker surface layer. As a result, it gradually condensed into a dense structure block with small pores and smooth surfaces, which led to higher strength. In conclusion, using the vanadium slag to prepare Portland cement can realize the utilization of solid mineral wastes, which will bring huge ecological and economic benefits.INTRODUCTIONWith the development of China’s mining industry, more and more mineral waste residue is discharged every year. These solid wastes cause varieties of resources and environmental problems on people’s living area. While at the same time, the demands of cement are increasing with the remarkable development of the construction industry. Thus, in recent years, utilization of proper solid waste to prepare cement has become an efficient way to deal with the solid mineral wastes problems (Boncukcuoglu, Kocakeri?M, & Tosunoglu, 2002; Simatupang, Hanafi, Purwasasmita, Imran, & Pane, 2012; Tsakiridis, Papadimitriou, Tsivilis, & Koroneos, 2008; Yun, Yong, Choi, Lee, & Lachemi, 2009)."

Jan 1, 2016

By A. M. A. Mohamed, F. H. Samuel, S. Alkahtani

"This article was undertaken to investigate the effect of nickel and zirconium additions on the strength of 354 aluminum cast alloy. The cast alloys were given a solutionizing treatment followed by artificial aging at 190 ºC for 2 hr. High temperature tensile tests were conducted at various temperatures from 25ºC to 300ºC. Optical microscopy and scanning electron microscopy were used to study the microstructure of the samples. The results revealed that the intermetallics phases of (Al,Si)3(Zr,Ti), Al3CuNi and Al9NiFe are the main feature in the microstructures of alloys with Zr and Ni additions. The results also indicated that the tensile strength of alloy decreases with an increase in temperature. The combined addition of 0.2 wt% Zr and 0.2 wt% Ni leads to a 30% increase in the tensile properties at 300ºC compared to the base alloy.INTRODUCTIONThe task of improving the mechanical properties in an aluminum alloy at high temperatures should include the knowledge of several factors which are related principally to a decrease in the strength of the metal with increasing temperatures. This behavior is linked to the change or deterioration in the principal metallurgical parameters of the specific cast aluminum alloy during its performance at higher temperatures. Most of applications of Al-Si casting alloys are generally used at temperatures of no more than 230°C (Lee & Chen, 2002). This recommendation is made in view of the fact that, for certain applications such as those required by the automotive industry, these alloys must operate over a wide range of temperatures and stress conditions where temperatures are liable to rise even higher than 230ºC (Robson & Pragnell, 2003).Aluminum-silicon-copper-magnesium alloys such as the 354 alloys show a greater response to heat treatment as a result of the presence of both Mg and Cu. These alloy types display excellent strength and hardness VALUES (although at some sacrifice of ductility and corrosion resistance. These alloys are used for a wide range of applications, such as engine cooling fans, crankcases, high speed rotating parts, structural aerospace components, air compressor pistons, fuel pumps, compressor cases, timing gears, rocker arms, machine parts, and so forth (Cáceres, Svensson, & Taylor, 2003; Rurrxia, Rong-de, Yu-hua, Cherrxi, Xiao-feng, Heng-rong, & H. Zhuang-qi, 2004)."

Jan 1, 2012

By Rob Kelso

What is a Lunabot? ?Robot Controlled Remotely or Autonomously ?Visual and Auditory Isolation from Operator ?Excavates Black Point 1 (BP-1) Simulant ?Weight Limit - 80 kg ?Dimension Limits - 1.5m width x .75m length x .75m height ?Designed, Built and Tested by University Student Teams

May 1, 2013

By Charles Amoah

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012

By W. D. Madeley

Synthetic minerals were made from pure starting materials and galena samples were doped with the title metals. Microscopic, microprobe and X-ray examination confirmed that the dopeants were in solid solution. Paired flotations in a Hallimond-tube apparatus were performed to determine relative flotation response using Aerofloat 238 promoter. Results of these tests show that silver-doped galena floats more readily than pure galena and that galena doped with bismuth floats less readily than pure mineral to a 95% confidence level. Galena doped with both silver and antimony as AgSbS2 shows no detectable effect. Antimony-doped galena followed the expected trend, but not to 95% confidence. The results are consistent with the theory that flotation by thiol-type anionic collectors is enhanced by p-type semiconduction.

Jan 1, 1978

By Yoshimasa Funakawa, Kazuhiro Seto, Akio Kobayashi

A new hot rolled high strength steel consisting of ferrite matrix and nanometer¬sized precipitates was developed. The ultra fine precipitates were identified as TiMoC2, and the strengthening by the precipitates was evaluated more than 300MPa in case of TS/800MPa grade steel. Due to the strengthening effect of the ultra fine precipitates, alloy elements for solid solution hardening can be reduced. It is notable that the steel shows very high yield strength (730MPa in case of TS/800MPa) and very high local elongation leading to excellent stretch flange formability at the same time. The mechanical properties of the steel are attractive for chassis parts and structural parts of auto body. The steel has been produced commercially, and applied to the parts successfully.

Jan 1, 2004

By C. Langer

Although the existence of precious metals, particularly those of the platinum group, in the nickel ores in the Sudbury district has been known for a good many years- almost as long as the ore deposits themselves- the Mond Nickel Company were the first to effect their recovery on a commercial scale. The precious metals values of the different Sudbury ores vary considerably, and are generally higher in the copper-rich ores. These values are so very small that a direct determination in the ores gives quite unreliable results. This is not surprising if one considers that some of the ores contain on1y one unit of total precious metals in about two million units of ore, and that this one unit will consist of seven different metals, each with a different chemical behaviour. It is only after the ores have been smelted to a Bessemer matte containing about 80 per cent combined copper and nickel that the precious metals content can be determined with some degree of certainty. From the figures thus obtained, the precious metals content of the ores can be calculated, provided the tonnage of ore used to produce one ton of matte is known. The recovery of these minute quantities of precious metals out of ?such a large amount of gangue and sulphides of iron, copper, and nickel seems at first glance a commercial and technical impossibility. Nevertheless, science has found a way to conquer all the difficulties, and quite substantial quantities of the precious metals contained in the Sudbury nickel-copper ores have been regu1arly recovered for many years by the Mond Nickel Company.

Jan 1, 1927

By James W. Cameron

DESPITE the fact that, after oxygen and silicon, aluminum is the most abundant and widely distributed element in the earth&apos;s crust, it is, commercially, a modern metal. Attempts were made by Sir Humphrey Davy and other chemists to decompose alumina, the oxide, into its elements, but with unsatisfactory results, and it was not until 1827 that Wohler succeeded for the first time in isolating the metal in pure form. Some thirty years later, commercial production of aluminum was started in a plant near Alais, France, using a process developed by Deville which was a modification of that of Wohler. It was not, however, until around 1886 that possibilities of low-cost production were realized. Hall and Heroult discovered, independently, the now famous process for extraction of aluminum by the electrolysis of alumina (Al,O,) dissolved in fused cryolite. This discovery, with its subsequent effect in reducing the price of the metal, was perhaps the greatest single factor contributing to the remarkable growth of the aluminum industry. But only in the years following the Great War did aluminum begin to attain equal importance in many fields with other non-ferrous metals. Numerous factors, political and economic, in the past decade have had a profound effect on the industrial history of the metal. At present, systematic substitution of aluminum for other base-metals is proceeding at a rapid rate in such countries as Germany and Italy with a view towards &apos;economic self-sufficiency&apos;. Quite naturally, ?the economic depression started extensive research and experiment in various industries in an attempt to improve efficiencies and lower costs. Partial answers have been found in the extended use of aluminum and its alloys. Even against the background of tremendous technological advance that has marked the past fifty years, the rise of the aluminum industry must necessarily stand out conspicuously.

Jan 1, 1939

By A. Karzhau, B. Aldamzharov, Y. Tussupbekov

"This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of the mine 24 hours a day. The mine auxiliary ventilation has been designed with the maximum length of ducting systems with extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal. The mine needs additional investments for re-designing ventilation network and therefore needs to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation network optimisation processes at the operational metal mine in Kazakhstan. Mine ventilation surveys were undertaken for validation of the computerised ventilation model. The mine ventilation network modelling has been undertaken to be compliant with Kazakhstan mining regulations. Results of the mine ventilation optimisation processes were analysed in terms of financial risks for investments into reconstruction of the ventilation shafts, extension of the ventilation network, variable speed fans and automated regulators. Savings were resulted from improving ventilation system efficiency by reduce airflow in areas without mining activity and redistributing existing ventilation capacity. Based on savings derived from the optimised ventilation network an additional NPV has been received. Stochastic modelling use Monte Carlo simulation producing representation of possible outcomes for the additional NPV considering electricity pricing as a major variability. As result probability distribution for the optimised ventilation network demonstrates the additional NPV in a range of 1.6 - 2.2 million US$ in the corresponding defined value of 90%. Moreover, there is only 5% chance that the additional NPV to be less than 1.5 million US$. Conducted risk analysis for ventilation network optimisation processes gives considerations on volume of investments into the mine ventilation system.INTRODUCTIONCosts for mine ventilation are typically increasing when mines expand to deep levels. Some underground mines in Kazakhstan still use continuously operating fans at its maximum capacity. This is not helping to save energy and costs that are in many cases very significant. This case study produced for the metal mine operating in Kazakhstan, which has ventilation controlled manually and working continuously at maximum speed to keep air flowing through each part of a mine 24 hours a day. The mine auxiliary ventilation has been designed with maximum length of ducting systems and extra air volumes to compensate for potential leakage. The mine provided auxiliary ventilation to all production stopes even to those, which for various operating reasons become temporarily inactive. However, mine safety has to consider risks associated with the deficit of fresh air for mine gases dilution and removal from the mine workings (Sabanov, 2019). The mine needs additional investments for re-designing ventilation networks and therefore need to estimate financial risks associated with it. The aim of this study is to conduct risk analysis for ventilation networks optimisation processes at the operational mine in Kazakhstan. Mine ventilation surveys for validation of the computerised ventilation model have been undertaken"

Jan 1, 2019

By Stanislaw Trenczek

Natural hazards such as rock bumps, methane, coal dust explosions, airborne respirable dust, outbursts of gas and rocks, water, radiation caused by natural radioactive materials, spontaneous fires, and climatic hazards, occurring in the Polish hard coal mines, should be controlled. These hazards are characterized by different scale levels numbered from 2?5. To recognize the amount and levels of hazards, research works were carried out in 109 mining districts of mines belonging to Jastrzebska Spólka Weglowa, Katowicki Holding Weglowy and Kompania Weglowa. These are 86 % of all mines and could be regarded as representative of the majority of Polish mining. The hazards have been classified as regards the frequency of their occurrence as: commonly occurring ? with a frequency of 100 % (like airborne respirable dust and fire hazards), high occurrence frequency ? frequency from 60 to below 100 % (methane hazard ? 83.5 %, coal dust explosion hazard ? 92.0 %, and water hazard ? 99.1 %), medium occurrence frequency ? from 30 to below 60 % (rock-bump hazard ? 52.3 % and climatic hazards ? 51.4 %), and episodic occurrence frequency ? below 30 % (outburst of gas and rocks and radioactive hazards). The dynamics of effects of growth in hazard levels to their intolerable values is diverse. Some of them are passive in nature, which allows for longer observation of changes and appropriate early response (as for climatic and spontaneous fire hazards). However the majority of them take on the character of disasters, like methane or coal dust explosions and damage of the excavation structure ? as occurs after a rock-bump or rock outburst; and creation of an atmosphere unfit for breathing ? during open or spontaneous fires, or after gas outbursts containing methane. There are also latent hazards whose effects do not influence indeed a process of production; however they are detrimental to health when a worker is exposed for a long time to airborne respirable dust and radiation. For other types of hazards a level of danger may be only estimated. Since the systems monitoring allows a wider range of control, therefore, aside from rock-bump and methane hazards, there are monitored also fire hazards including measurements of other air parameters (velocity, pressure, humidity, temperature, O2, CO2 concentration). A few types of monitoring systems are used in Polish mines, like the monitoring systems for environmental parameters such as SMP-NT, SMP-NT/A, the telemetric systems CST-40, CST/A, including the computer-aided system for methanometry control officer SWµP, the computer-aided measuring systems KSP-1, KSP-2, KSP-2C, or the production and safety control system VENTURON. The underground part of the systems monitoring of natural hazards contains measuring devices and equipment for automatic control (power-off) of machines and electric devices in case of increased methane hazard. The surface part of the monitoring system allows the measuring data to be visualized and pre-alarm (warning) and alarm states to be displayed. Furthermore it makes it possible to archive and report the data and to control the underground supply and signalling devices. The EMAG Institute developed monitoring methods to extend a measuring range of monitored parameters (such as methane and fire hazards) as well as to monitor so far unmonitored hazards like dust hazards (by continuous monitoring of dust levels in mine air) and climatic hazards (by online monitoring climatic parameters of mine air).

Aug 1, 2013