Search Documents

By R. Agarwal

The in-situ stress field was determined, using the overcoring technique, at two underground sites at the Pea Ridge Mine, Sullivan, Missouri. At one of the sites in magnetite, the three dimensional stress field showed the largest principal stress to be compressive (-4564 psi), nearly horizontal and closely parallel to the strike of the orebody. The smallest principal stress was also compressive (-2047 psi) and nearly vertical. Considerable difficulty was experienced in drilling porphyry rock at the second test site in the host rock. Only one hole was drilled at this site. The secondary principal stresses obtained in the porphyry are -9464 and -4945 psi, respectively. The-test site in magnetite is located at a depth of 2505 feet whereas the site in porphyry rock is at 2475 feet. The vertical stresses: due to overburden loading at these sites are -3590 and -2782 psi, respectively. Field determined values of the vertical stress are -2207 and -5098 psi, respectively. The variance; between the two sets of values is most likely attributable to the orebody formation and the differences in the modulii of the host rock and the orebody.

Jan 1, 1977

By Wesley A. Grosh

The Vest nickel prospect, in Floyd County, Va., was discovered about 25 years ago. Limited exploration of the deposit had indicated some appreciable nickel mineralization in the sulfide ore. The property was examined on March 9, 1943, by an engineer of the Bureau of Mines in company with C. W. Vest, owner of the property. A limited exploration program was recommended. Two holes totaling 320 feet were diamond-drilled in January 1944. Drilling indicated the sulfides are sparsely disseminated. The only nickel values of interest were at the old prospect shaft.

Jan 1, 1949

By Glenn C. Reed

This report is one of a series describing mineral investigations within the Missouri River Basin in Montana. The primary purposed of these investigations is to provide information to agencies of the Department of the Interior and others concerned with the planning of Federal power developments in the basin. This report is limited in score to consideration of mineral deposits of presumed inventory value within Gallatin County, Mont. The field investigations were made during the fall of 1948.

Jan 1, 1951

In 2004, a total of 4,401 stone mining operations reported employment to the Mine Safety and Health Administration (MSHA). Stone mines comprised 30.4% of all mining operations.

Sep 1, 2007

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with tie intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the New Galena Deposit in an endeavor to find an additional source of supply of lead. In Bucks County, lead and zinc minerals have been found in shales over a largo area west and northwest of Doylestown. Considerable mining has been done in the vicinity of New Galena on the North Branch of Noshaminy Creek, 3 miles northwest of Doylestown. It has not been possible to obtain a satisfactory history of the New Galena mine, as there is much disagreement in statements. Most of the mining was done in open pits. Two shafts were sunk to shallow depth; one of these became part of the main pit' which is 256 foot long, 50 to 75 feet wide, and 20 to 44 feet deep. Small pits 8 to 10 foot square wore sunk on the ore zone, which extends some 1450 feet to the southwest. The rock containing the minerals is either black or gray shale. The gray material closely resembles limestone. The following minerals have been reported from the mine: quartz, ankerite, calcite, galena, sphalerite, pyrite, chalcopyrite, and bornite. Some of the galena has yielded 10 to 15 ounces of silver and 10 cents in gold per ton. The average grade of the ore as mined is not known. To investigate the downward extension of the ore shoot, the Bureau drilled two holes aggregating 373.9 feet, No additional ore was developed by this work.

Jan 1, 1950

By P. R. Bremner

The United States is more than 90 pct dependent on imported bauxite a source for aluminum, but it has vast nonbauxitic aluminum resources, such as kaolinite, anorthosite, alunite, etc. As part of a program to devise processes for treating these resources, the Bureau of Mines investigated a bench-scale leaching process using hydrochloric acid (HC1) and fluoride to extract aluminum from Wyoming anorthosite. HC1 and fluoride-to-aluminum (F/Al) mole ratios were studied with respect to aluminum extraction for single-stage, cocurrent, and countercurrent leaching modes. Using 95 pct stoichiometric HC1 and a F/Al mole ratio of 0.27, 90 pct of the aluminum was extracted by countercurrent leaching. Single-stage leaching with the same amount of acid and fluoride extracted 48 pct of the aluminum. Three fluoride sources, CaF2, Na2SiF6, and H2SiF6, were used and gave similar results on aluminum extractions.

Jan 1, 1982

By Rogers F. Davis

The Bureau of Mines developed a new method for the determination of oxides of nitrogen in diesel exhaust gas. The procedure, a modification of the Saltzman method, uses a NO2 absorbent for the diesel exhaust gas; the colorless absorbent becomes purple on contact with N~. When used properly this procedure gives satisfactory results in 2 hours, whereas the standard phenoldisulfonic acid method required approximately 8 hours. The new method is not satisfactory for determination of oxides of nitrogen in the overrich fuel to air ratio range.

Jan 1, 1966

By G. E. Walden

The Bureau of Mines is currently engaged in a continuing investigation of the thermodynamic properties of certain inorganic compounds. As a part of this investigation, the heat contents of bismuth and cerous chlorides were measured throughout the temperature ranges of 370° to 630° K. and 370° to 1,200° K., respectively. Equations representing heat contents as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate heat contents at selected temperature intervals ranging from the ice point to 650° K. for bismuth chloride and to 1,200° K. for cerous chloride; also, the heats of fusion of both compounds were calculated at their respective melting points. EXPERIMENTAL Materials The cerous chloride used in this investigation was supplied by the National Carbon Company of Cleveland, Ohio. A chemical analysis indicated Ce 56.57 percent and Cl 43.39 percent. No attempt was made to purify the compound or identify impurities since the analysis showed only about 0.04 percent total impurities. Reagent grade bismuth chloride was used without additional purification.

Jan 1, 1961

By John Campbell, Miller. W. E., G. W. Jones

"INTRODUCTION Because of its interest in accident prevention, the Federal Bureau of Mines has cooperated with city officials and utilities in investigating the causes of explosions in sewers, manholes, and other underground spaces and has aided in the development of means to prevent such explosions. For several years this Bureau has cooperated with the Boston Edison Co. and the Boston Consolidated Gas Co. of Boston, Mass.,for the purpose of detecting and eliminating combustible and physiologically harmful gases in manholes in Boston and vicinity.These investigations 5/ have shown that combustible gases from the usual sources — leakage from gas—distributing systems and underground tanks and gasoline wastes — can be located and the dangerous conditions remedied by a well—planned, adequately supervised, systematic, and continuous manhole survey. However, other types of gas contamination, termed ""soil"" gases, are present in manholes at times and are more difficult to eliminate because they have no fixed origin and because seasonal and barometric chances affect their production and passage into the manhole. Soil gases usually are abnormally high in carbon dioxide and low in oxygen and contain varying amounts of methane. They are especially dangerous to men entering manholes because they lack sufficient oxygen to support life."

Feb 1, 1940

Develop new technology to encourage domestic processing of automobile catalytic converters for recovering platinum -group metals. Background Automobile catalytic converters are used to convert pollutants in automobile exhaust into water vapor, carbon dioxide, and nitrogen, About 1 million troy ounces of platinum-group metals arc used each year in the. United Slates to manufacture catalytic converters. It has been estimated that about 60 pct of the used catalytic converters arc being collected. Most of these used catalytic converters were not processed in the United States but were exported to Japan or Europe for processing. In 1991, about 250,000 troy ounces of platinum-group metals were recovered from scrap catalytic converters collected in the United States. Each short ton of decanned catalyst may contain 30 troy ounces of platinum-group metals valued at over $15,000. Development of an economic process for the recovery of platinum-group metals that can be operated on a small or large scale may increase, the percentage of catalytic converters collected and encourage domestic processing to recover a platinum-group metal concentrate. This would significantly decrease the dependence of the United States on imports for these critical and strategic metals.

Jan 1, 1992

By By Staff

"These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar on postdisaster survival and rescue research. Several seminars are held each year to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.INTRODUCTIONThe postdisaster research program is directed toward research and development of technology and equipment that increases the chances of a miner surviving or being rescued after an underground mine disaster. A disaster is an accident of major proportions, and it may result in the entrapment of miners whose normal egress from the mine is cut off. This often necessitates a rescue operation and a means of keeping the trapped miners alive while they await rescue. The Bureau is currently pursuing research to develop the technology that will enhance the ability of miners to survive such an occurrence. The research is divided into two basic problem areas, survival and rescue. Both areas are concerned with the inability of miners and rescue teams to cope with the postaisaster environment, such as toxic gases, unstable roof conditions, water flooding, and lack of oxygen. In addition, research is also conducted to find ways of locating and quickly reaching trapped miners. Most of the research conducted by the Bureau has been directed toward the postdisaster problems associated with coal mines. However, most of the research results are also applicable to noncoal mines as well.The papers presented in these proceedings address some of the recent research conducted by the Bureau of Mines that has been directed toward the postdisaster problems outlined above. The topics covered range from an overview of the technology developed for oxygen selfrescuers to training programs for mine rescue. Any questions or comments pertaining to this research are encouraged and appreciated. Open file report (OFR) references in the proceedings listed as available from NTIS may be obtained from the National Technical Information Service, Springfield, Va. 22161, and are also available for reference at Bureau of Mines facilities in Denver, Colo., Twin Cities, Minn., l3ruceton and Pittsburgh, Pa., and Spokane, Wash.; the Department of Energy facility in Morgantown, W. Va.; the National Mine Health and Safety Academy, Beckley, W. Va., and the National Library of Natural Resources, U.S. Department of the Interior, Washington, D.C."

Jan 1, 1982

By J. E. Matta

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method. Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out-crop will emit low levels of methane gas.

Jan 1, 1977

By Eugene Frey

The Romur is one of several properties in the Copper Mountain mining district, Fremont County, Wyo., that contain scheelite deposits. The district lies on the southern slope of the Bridger Mountains, 18 miles northeast of Shoshoni and 15 miles from the rail point at Bonneville on the Chicago, Burlington & Quincy Railroad (figs. 1 and 2). The tungsten deposits occur in a zone of pre-Cambrian schists and gneisses that have been cut by numerous basic dikes and granite pegmatite dikes. Scheelite occurs in lenses and pods that lie parallel to the foliation and bedding in the metamorphic rocks. The more important deposits are found in a lime-silicate rock consisting primarily of zoisite but with small quantities of quartz and carbonate. Scheelite was found in December 1941, and the area was mapped by the U. S. Geological Survey early in 1942. In November 1942 the Bureau of Mines commenced work on the Stardust-Comet group for the purpose of developing reserves for war requirements. The initial work consisted of driving an alit in the ore zone a distance of 109 feet. This zone was sampled during the progress of the work, and subsequently surface and underground exposures on adjoining properties also were sampled (figs: 5, 6, 7, and 8). One hundred twenty-four samples were obtained. Sample and assay data are shown in tables 2, 3, and 4.

Jan 1, 1950

By Edward D. Thimons

The Bureau of Mines has developed a damage-resistant brattice, intended for use as a stopping in locations where blast damage to stoppings is a problem, the roof is relatively flat, and the differential pressure across the stopping is not high. Damage-resistant brattices consist of a series of vertically hung brattice panels joined to each other by Velcro connections that improve the airtightness of the brattice. When the brattice is subjected to strong blast forces, the Velcro connections peel apart, allowing the panels to open without incurring damage. The Velcro connections can then be resealed in a matter of minutes. A preliminary test in the Bureau's Safety Research Mine and subsequent long-term testing at the White Pine copper mine in Michigan and the Retsof salt mine in New York show that damage-resistant brattices withstand blasting better than conventional stoppings, while still performing as efficient air barriers when the Velcro connections are sealed.

Jan 1, 1978

By Russell R. Trengove

The Strawberry tungsten mine is in the Jackass Mining District, in an isolated portion of eastern Madera County, near the southeast corner of the Yosemite National Park. The deposit was discovered in 1941, and production started in 1943 when the mill was completed. With the exception of 1946 and 1947, production has been continuous. The area in the vicinity of the mine is granite containing islands of sedimentary beds highly altered by metamorphism that resulted from the intrusion of acid igneous rock. Schoelite occurs in almost vertical lenses of tactite between the limestone and the granite.

Jan 1, 1949

By R. W. Van Dolah

An important function of stemming used to confine explosives in shot holes in underground coal mines is to minimize the chance of ignition of firedamp or coal dust by the detonation products. Until 1952, the Bureau of Mines approved only the use of fireclay or similar incombustible material for stemming permissible explosives. At least 2 feet of stemming were required except in holes less than 4 feet deep; in such short holes the stemming was required to be half the depth of the hole. Over the years, several special stemming devices have been proposed in the United States as substitutes for fireclay. Many economic and safety advantages were claimed for these devices, but only one approved device has been marketed in this country. Bureau requirements for stemming explosives in coal mines were modified at that time to permit the approved stemming device to be used as a substitute for the required fireclay.

Jan 1, 1961

By S. F. Ravitz, T. M. Romslo

During 1940 and 1941, the Bureau of Mines examined a large number of silver mines in Arizona for their potential as producers of manganese ores. Although very little manganese ore had been produced from these mines, it was generally known that manganese oxides in appreciable amounts were associated with the silver ore. Following the examinations, the Bureau further investigated some of the ore deposits by diamond drilling and other types of sampling. The results of these investigations, from the viewpoint of manganese, were discouraging. However, the investigations did indicate that appreciable tonnages of manganese-silver ores had been left in some of the mines by earlier operators. Most of these ores were too low-grade for direct shipping as ores of manganese or silver, and their beneficiation by ordinary processes was not economic. Exploitation of the ores appeared to be dependent upon the development of a low-cost milling method, which would yield a marketable manganese product and recover a high percentage of the silver. Later, the Bureau of Mines constructed an experimental mill at Salt Lake City, Utah, for the treatment of manganiferous ores by the dithionate process, designed to recover manganese as a high-grade product. The dithionate residues can be treated by other processes for the recovery of additional values that may be present in the ore. This development focused attention on the manganese-silver ores of Arizona and led to setting up Bureau project No. 370, which is the subject of this report.

Jun 1, 1947

By Michael S. Miller

In 1986 and 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 550-acre Carson-Iceberg Wilderness Study Area (NV-030-532), in order to evaluate its identified mineral resources. The Wilderness Study Area is located in Alpine County, CA, 11 mi southeast of Markleeville, CA. Tertiary volcanic and granitic rocks, as well as alluvium, underlie the area. Hydrothermal alteration and faulting have affected some rocks; argillic, silicic, and limonitic alteration are found, particularly near faults. No mineral resources were identified in the Wilderness Study Area. The area has one small pit and no mines or claims. Samples from the Wilderness Study Area and vicinity contained uneconomic amounts of gold, silver, copper, lead, zinc, mercury, arsenic, and molybdenum. Mineral occurrences are too small and low grade to be of interest within the foreseeable future.

Jan 1, 1988

By John R. Benham

In 1979 and 1980, the U.S. Bureau of Mines and U.S. Geological Survey conducted a mineral survey of the 20,500 acre Black Butte RARE II area (No. 5102) in the Los Padres National Forest (fig. 1). The work by the Bureau of Mines indicates that the potential tor mineral resources in the area is low. Samples of outcrops and stream channels contained no economic minerals. A mercury deposit near a granodiorite-sedimentary rock contact occurs 2 mi northeast of the study area, but similar deposits have not been discovered within the area. Geothermal potential exists near Tassajara Hot Springs, but no thermal springs occur in the area; nor have oil, gas, or coal resources been found.

Jan 1, 1982