Search Documents

By S. G. Hardcastle, K. C. Butler, M. G. Grenier

The most common method of determining airflow employed by mine ventilation engineers is the product of i) the average air velocity as measured by a vane anemometer and stopwatch through a continuous traversing technique, with ii) the cross-sectional area of the roadway. This method requires the vane anemometer to accumulate the total flow over the duration of the traverse. Historically, this has been facilitated by a mechanical analog instrument that has either a counter or set of dials that display the flow. Common instruments of this type are Airflow Development's AM5000, Davis's, or Taylor's Biram type anemometer. The AM5000 is widely used in the Canadian mining industry but is no longer available. Therefore, regulatory authorities have seen fit to evaluate presently available commercial instruments to replace the AM5000. This paper describes an instrument evaluation contracted by the Atomic Energy Control Board of Canada which regulates the uranium industry. Over the last two decades there have been numerous advances in the development of electronic air velocity meters. Currently available units have the following features: a) battery operation; b) are compact and can be hand-held; c) employ LCD's, and microelectronic circuitry; and d) provide a time integration for the duration of a traverse. These features make such instruments a possible replacement to the analog units and stopwatch determinations. This paper details five of the new generation of vane anemometers plus a vortex air meter, and it explores their limitations in comparison to analog units. Specific consideration is given to linear response, the effects of yaw, traversing speeds and ergonomics relating to both handling and use. The paper concludes with some features that are attractive and should be considered when purchasing a new anemometer.

Jan 1, 1991

By Patricio A. Espinoza, Aldo Casali, Cristian Ardiles, Guillermo González

Cluster analysis is used to design grade soft-sensors in a rougher flotation plant and a ball mill overload soft-sensor. Soft-sensors are virtual sensors which either replace unavailable actual sensors or infer measurements for non existing sensors. In the case of the grade soft-sensors clustering serves to determine clusters of related operating points. To each cluster there corresponds an ARMAX model structure whose parameters are estimated using only the points in the corresponding cluster. Thus a much better correlation is found than if all the data points were used for a global model. The problem of identifying clusters when the measurement of the real sensor is not available is addressed. In the case of the overload soft-sensor, variables were selected which are related to overload, either from a phenomenological point of view or according to operator experience. Different clusters are formed, some of which are identified as determining an overload condition or a possibility of such condition. Each of these clusters has a set of operating conditions which suggests the corrective action to be taken when necessary. Both kinds of soft-sensors are tested with industrial plant data and promising preliminary results are obtained.

Jan 1, 1995

By L. Alan Weakly

Coal mines and power plants utilize different methods to control dust for the safety of their workers and to protect their installations. The methods that they use are limited by the Environmental Protection Agency or the states in which they operate. Now there is a new technology for controlling dust at conveyor transfers! The Passive Enclosure Dust Control System utilizes several proven technologies to mitigate fugitive dust. This new system has been proven to be four times more effective than standard enclosures utilizing bag house collection and is considerably less expensive to install and operate.

Jan 1, 2000

By Francis S. Kendorski

INTRODUCTION Caving offers the lowest cost per ton of any large-scale mining method, but its successful application demands an ore body that conforms to several rigid requirements. The deposit must be of wide areal extent, massive and not spotty in ore values, and insensitive to ore dilution. It must also be a rock mass that breaks up readily. There are only three active caving operations in the US-Climax, Henderson, and San Manuel-but caving methods have recently taken on new importance as deeper lower grade mineral occurrences and ore bodies are found. These deposits are too deep for surface min¬ing methods, and too low grade to support any type of underground mining except a bulk method such as caving. Announced discoveries or indications that may be amenable to caving include: Climax's Mt. Emmons molybdenum discovery in Colorado; Molycorp's Goat Hill molybdenum prospect in New Mexico; the Phelps Dodge molybdenum deposit in Beaver County, UT; Arizona copper occurrences such as Asarco's Sacaton, Hanna's Casa Grande, Noranda's Lakeshore, and Ken¬necott's Safford; Anaconda's suspected deep copper de¬posit in Butte, MT; Anaconda's Carr Fork, UT, deposit; and perhaps others. CAVABILITY'S ROLE IN FEASIBILITY STUDIES Caving is a system of underground mining which removes support from underneath an ore body. As a result, the rock mass fractures, fails, and flows vertically downward by gravity to be collected in previously ex¬cavated funnels. Types of ore that have been mined by caving include molybdenum, copper, iron, nickel, as¬bestos, and diamonds (Julin and Tobie, 1973). It is primarily a large-scale method, with production rates of more than 45 300 t/d (50,000 stpd) having been achieved. However, the initial capital investment before return is very high, often in the hundreds of millions of dollars. The cavability of an ore body or mineral occurrence is a critical item in the feasibility study of a proposed mine, not only from the point of overall minability, but from the point of impact on other costs such as blasting, loading, hauling, crushing, and grade recovered. Aside from the often-asked question of, "Will it or will it not cave?" the real questions are, "Can we afford to make it cave, carry the rock away, and extract the mineral?" The last is not a topic of this chapter, but the first two are. The cavability of an ore deposit or mineral occur¬rence is based on many things, but clearly, if a large enough area is undermined, any rock mass will cave. The result could be a violent collapse as occurred at Urad, CO (Kendrick, 1970), or perhaps the rock mass will cave beyond the ore boundary. Another unfavor¬able result could be ore blocks that are too large for the equipment and orepasses to handle without considerable secondary blasting. Weak rock with numerous fractures may produce a very fine ore when it caves, resulting in dilution and ground control problems. DETERMINING STRUCTURAL DOMAINS It has long been recognized that the geologic nature of an ore body is important to cavability (King, 1946). Such items as weak rock material, intensity of fractur¬ing, and severity of faulting all contribute to the success of a caving operation, and information regarding these is required as a minimum for the cavability determination. In practice, the rock mass-defined as the blocks of intact rock together with the intervening fractures, joints, faults, bedding planes, and other discontinuities-that contains the ore body, as well as the surrounding and overlying rock, must be examined in a systematic and detailed fashion. Surficial geology maps must be pre¬pared, exploration holes drilled, and core logged for en¬gineering information. The fracturing of the rock mass must be studied to ascertain the three-dimensional dis¬tribution of fractures and their characteristics, and faults must be located and described. The strength and other mechanical properties of the rock material, the fracture surfaces, and the fault filling materials must be tested and reported for later use by designers and planners. With this basic information and an understanding of the geologic setting, the rock mass can be divided into one or more structural domains which tend to behave similarly in response to engineering activities (Robertson and Piteau, 1970). One must keep in mind that the determination of the structural domains goes beyond the geologic units present. Several lithologic units may be lumped together, while a single lithologic unit can be divided into multiple domains. Major faults often form their own domain, and the direction of engineering ac¬tivity-for example, cave advance to the north rather than the south-may alter rock mass behavior, resulting in different domains. As an example of the detailed rock fracture map¬ping required for such studies, the structural domain determinations at the Climax mine (Kendorski, 1973) are shown in Fig. 1. The circles are Schmidt equal area projections of the three-dimensional attitudes of frac¬tures (Ramsay, 1967) mapped in detail at various rock exposures. The attitude of fractures is important to the cavability determination since it dictates the directional behavior of the rock mass as it fails, and determines the effectiveness of arching, keying, and rock block inter¬locking. Low-angle fractures must be present to allow movement of the rock in the vertical direction during undermining (Mahtab and Dixon, 1976); if low-angle planes of weakness are absent, the rock mass may arch with a keystone effect, rather than moving vertically downward.

Jan 1, 1982

By S. Chander, A. Briceno

The properties of surface films on pyrite have been studied through electrochemical techniques of cyclic voltammetry and AC impedance, measurements. The characteristics of the surface films depend on the conditions of oxidation and the source of pyrite. At potentials near 0.0 V, some pyrites have large values of polarization resistance, showing a certain degree of passivity. Some pyrites show more passivation than others, however. On oxidation, meta- stable phases of Fe(OH)2 and Fe(OH)3 form that transform to more stable phases on aging. The growth of surface films near the corrosion potential of pyrite follows a linear kinetics that is attributed to a chemical (or an electrochemical) reaction as the rate determining step. The surface film is considered to be a hydroxide or an oxide because it is hydrophilic. This study has also demonstrated that AC impedance ,measurements can be used to study the growth characteristics of films at mineral/solution interfaces.

Jan 1, 1988

By R. C. Freas

Limestone is a basic raw material in the production of cement, lime, a wide variety of industrial products, and a significant percentage of the crushed stone produced in the United States annually. It is used in fluxes, glass making, mineral fillers, environmental applications such as flue gas desulphurization and water treatment, soil conditioners, animal feeds, and as a construction aggregate. This presentation provides an overview of limestone distribution in the United States, it’s production, the variety of products produced, and a brief review of the primary uses for limestone.

Jan 1, 2006

By Qiong Wu, Li Guo, Qinghua Gu

BP neural network is a multilayer feedforward network trained by error back-propagation algorithm, which is one of the most widely used neural network models. However, BP neural network has exposed more and more shortcomings and deficiencies with the expansion of the application scope. In the prediction of ore quantity, BP neural network has the characteristics of slow convergence and easy to fall into local minimum point. In order to obtain the global optimal solution, and to improve the defects of BP neural network, this paper proposes combination optimization algorithm of genetic algorithm (GA) and BP neural network to improve the speed and accuracy of forecasting the main design flow chart and the analysis of the sort distinguish algorithm are offered, and then some problem in the design and debugging of the algorithm are discussed. On this basis, the GA-BP neural network model is constructed and applied to optimize the initial weights and threshold value of BP neural network. This model choices the floating point coding method to encode the connection weights and thresholds, and divides subjects into several populations. Through the introduction of selection, mutation, crossover, initial weight and other operators, making operational synergies between the various groups. This study selects 30 geological units, 8 quantitative variables (Pb, Zn, Cu, Mo, Si, Ni, Co, V) and 12 qualitative variables to carry out empirical analysis. Then the simulation of the algorithm is carried out in MATLAB and the parameters are analysed. By normalizing the input samples, 22 groups of observation data are used as the training data for prediction, and the latter 8 groups of observation data are used as the test data to be verified. The results show that when the ore quantity characteristics are not very significant, the model will produce prediction bias. But the improvement of the algorithm increases the efficiency of the function approach capacity of BP neural network and conquer the BP neural network system’s instability. It provides an auxiliary guide for ore prediction, which have higher reference value.

Jan 1, 2017

By J. F. Cuderman

In situ experiments at the Department of Energy's Nevada Test Site (NTS) have extended the technology of propellant-based fracturing to include liquid- filled, uncased boreholes. Previous work had developed the technology for liquid-free, uncased wellbores. Test results show that fracturing behavior is considerably more complex in liquid- filled boreholes than in the liquid-free case. Compared to liquid-free boreholes, liquid-filled boreholes have faster pressure risetimes and lower peak pressures, large hydraulic-type fractures propagating several meters beyond the end of the test zone, numerous oscillations in the pressure history, and variable types of fracturing within a single test region. Multiple fracturing is initiated in the wellbore of a fluid-filled borehole when the proper propellant mixture is used but, unlike fluid-free wellbores where up to eight fractures propagate, only one to three hydraulic- and/or shear-type fractures propagate. Hydrodynamic effects involving liquid compression during borehole pressurization appear to be responsible for the differing phenomena observed in fluid- filled boreholes.

Jan 1, 1986

By John E. Riddell

This review is based on a questionnaire sent out to 24 Canadian exploration companies, known to be active in the mineral exploration field, concerning their practice in the use of applied geochemical techniques in Precambrian terrains. Of the companies questioned, 16 returned completed questionnaires and of these, ten companies stated that they had some experience in this type of work. Of the companies who did not answer or return the questionnaire in time I know that at least three have been quite heavily engaged in applied geochemical work in the glaciated Precambrian areas. I also know that these three companies have been reasonably successful in their ventures, so I feel the following figures and opinions are, if anything, on the pessimistic side. Before continuing with the paper I would like to express my personal thanks to the Chief Geologists, Geologists and Exploration Managers of the various companies who cooperated in making this review possible by answering the questionnaires and making available summaries of their work in the glaciated terrains. Of the companies who stated that they had no experience in geochemical prospecting in glaciated Precambrian areas it is interesting to note that only two have reported that they do not use applied geochemistry at all. Two companies have reported that they make use of applied geochemistry in New Brunswick in areas of-light glaciation. Their opinion is that it is a useful aid to other techniques in evaluating mineralized areas.

Jan 1, 1960

By Thomas J. Ferree

The efficiency of Carbon-in-Pulp and Carbon­in-Leach circuits is determined by the degree to which the carbon can extract the gold from the slurry and transport it to the stripping circuit. The 'pick-up' efficiency of the carbon particles is affected by several factors which include the following: * The concentration of the carbon in the slurry. * The surface area of the carbon particles. * The reactivity characteristics of the carbon particles. * The retention time of the carbon in the slurry.

Jan 1, 1992

By S. Bhattacharya, M. M. Singh

The Surface Mining Control and Reclamation Act of 1977 (SMCRA) requires under-ground coal mine operations to prevent "material damage" to renewable resource lands caused by subsidence. However, what constitutes material damage is not defined. This paper discusses the applicable criteria for agricultural lands, forests and grazing lands, surface water bodies, and ground water aquifers. Although data on the subject are limited, an attempt is made to present quantitative guidelines to distinguish between moderate and severe damage due to subsidence.

Jan 1, 1988

By Aladar B. Dory

INTRODUCTION Practical experience in mines with known presence of radon daughters in the mine atmosphere in Canada and elsewhere shows that a very high concentration builds up in an unventilated dead end heading. As Holaday et al1 observed, even a minimal air movement results in a drastic reduction in radon daughter concentration. It is therefore obvious that the main objective of radon daughter control in the working environment is to design the ventilation system providing an optimized flow of fresh air into the workplace, resulting in acceptable climatic conditions and achieving radon daughter concentrations resulting in exposures as low as reasonably achievable. BASIC OBJECTIVES Large mining companies, having extensive material resources and professional expertise, have utilized elaborate electrical modelling in the design of mine ventilation systems as early as 1950 (coal mining industry in Europe) and with the advance of computer modelling techniques, their utilization in ventilation systems design is on the increase. Unfortunately, these methods are usually not available to small mining companies and even the large companies might not achieve the fullest benefit from utilizing them, if proper limiting factors are not considered in the modelling. When an evaluation of a ventilation system of a mine is undertaken in literature, a measure of the amount of air supplied underground per one ton of ore mined is used as an indicator of the efficiency of the ventilation system. Yet, even the greatest amount of air forced into the mine might not result in an acceptable working environment if a proper distribution of this air into individual working places is not achieved. The volume and the age of the air are probably the two most important factors in achieving acceptable radon daughter concentrations in the workplace, but other factors also have to be considered. DIRECTOR MINE - ALCAN, NEWFOUNDLAND FLUORSPAR WORKS ST. LAWRENCE, NEWFOUNDLAND, CANADA Ventilation To illustrate the effects of the design of the ventilation system on the control of radon daughter concentration, let us review the gradual development of the ventilation system of this mine from the earlier years of its development up until its final years of operation. This mine, located near the community of St. Lawrence on the south coast of Burin Peninsula was developed in the late thirties and reached full production by 1942. Unfortunately as was customary at that time, the only source of ventilation was a natural draft. The mine was extremely wet, and no significant attention was initially given to possible health effects of dust. It was not until the mid-fifties, when a number of cases of silicosis had surfaced, that de Villiers and Windish2 observed a significant increase of lung cancer incidence among the miners in comparison to its incidence among the general population of Newfoundland. Suspicions regarding radiation as a cause of the lung cancer were expressed, but it was only in surveys taken in late 1959 and early 1960 that Windish3 and Little4 established the presence of radon daughters in the mine atmosphere in very high concentrations. Windish, de Villiers and Hurley suggested that the most likely source of the radon in the mine was the mine water which dissolved radon during its passage through the granitic country rock in the surrounding geological area. This conclusion was confirmed by analyses of water from various areas of the mine by the Atomic Energy Canada Limited laboratories. The radon values in the samples varied from 4,240 to 12,850 pCi/L5. Following the discovery of the presence of radon daughters in the mine, the company took speedy action to install mechanical ventilation for the mine. The system was not designed as a total unit, but fans were installed rather on a trial and error basis. The basic system installation began in March 1960 and was completed by 1962. It remained basically unchanged with only minor modifications until August 1973 when a wholly new, redesigned ventilation system was implemented. A schematic section of the mine and its ventilation system for the period prior to March 1960 is given in Figure "A", for the period 1960-1973 in Figure "B", and for the period after August 1973 in Figure "C". The ventilation system prior to 1960 is not known. All workings of the mine were ventilated only by natural ventilation. If any measurements of airflows at different or any times of the year ever existed, no records have been preserved. The very minimal natural ventilation was augmented by "blowing" air from compressed air supply lines and exhaust air from drills. It is known that the compressor capacities of the mine were limited and therefore no significant air movement was probably created by the "blowing".

Jan 1, 1981

By Ehsan Alavi Gharahbagh

Tool and cutterhead wear is a crucial issue in soft ground tunneling, especially because tool inspection, maintenance, and replacement are done under difficult conditions, and often under pressurized faces or under ?hyperbaric interventions?. Overall, tool inspection and changing is a time consuming and costly step, which needs to be quantified and the related costs accounted for in any construction contract for scheduling and costing of the tunnels at design stage or bid preparation. However, lack of a universally accepted index or measure for soil abrasivity in the geotechnical reports has made it difficult, if not impossible, to define cutter wear for this purpose. Soil abrasion and its impact on cutting tools for tunneling machines under dry or wet conditions have recently been under spot light due to construction claims in several of the recent tunneling projects. The objective of this paper is to examine soil?s physical, mechanical and tribological properties related to the interface of the soil and excavation tools and discuss ways to measure soil abrasivity in a quantitative and repeatable manner. The paper will discuss the efforts that are underway to develop a new soil abrasivity index and the fabrication of a new testing device for this purpose.

Jan 1, 2010

By H. Huang, J. C. Wu, C. H. Xie, Y. Q. Xue, Z. H. Zhang

Two- and three-dimensional groundwater flow models for dewatering in an opencast mine are presented. The models focus on solving special problems using numerical simulations of the opencast mine. These special problems include the drying up of the aquifer, the movement of the model boundary and the prediction of the residual head. These models are used to describe the decline of groumdwater levels in the Yuanbaoshan Opencast Coal Mine and its neighboring area during the drainage period. The simulated values agree very well with the field data. There have been several successful examples of numerical simulation for predicting the mine dewatering rate in an opencast mine. However, The hydrogeological conditions for the Yuanbaoshan Opencast Coal Mine are rather complex, and the total average flow rate is very high at 4.676 x 105 m3/d (1.65 x 107 cu ft/day). In this paper, a two-dimensional groundwater flow model in a large area is developed to solve the problems mentioned above by simulating regional drawdowns of the groundwater level during the drainage period, and a three-dimensional flow model is developed to simulate the residual head near the open-pit bench.

Jan 1, 1998

By James Stewart

"THAT WHICH WE CANNOT SEE" INTRODUCTION Often it has been stated that the greatest of all fears is fear itself - fear created only by that which we cannot see or by that which we fail to understand. The elimination or minimization of fear can best be accomplished by a thorough understanding of the underlying causes of the fear. As related to the mining industry the omnipresent fear is the dread of acquiring cancer through accumulated exposure to "that which we cannot see" - radioactivity. The understanding of the resulting exposure effects can best be obtained through acquisition of authentic data and the subsequent analysis of the same by a group of highly qualified specialists. I may point out that the nuclear industry and its source, uranium mining, greatly surpass any other industries in the degree of public awareness as to its potential environmental effects. Public out-cry has always influenced major decisions relating to how industries conduct their operations and much of their effort has resulted in many changes. The issues of health and safety in the mining industry have created considerable public concern, but intense concern to those of us directly involved within the industry. Increasing concern regarding the effect of human activity on the quality of the outer environment of air, land, and water has developed within the past two decades. There is now a growing concern about the health and safety of persons at work in their inner environment, of their working-places in industry. Hearings and investigations conducted in Canada by three appointed "Royal Commissions" have all confirmed that this concern is well justified when focused on the health and safety of workers in our mines. REGULATORY CONTROL OF URANIUM MINING OPERATIONS In Canada, the ownership of mineral resources and the control of their extraction, except for uranium, is vested under the "British North America Act" in the provinces. In all provinces the statutory basis for health and safety provisions in the mining industry can be found in the provincial "Mining Acts" with each province assuming the responsibility to produce its own "Mining Act". In particular, all of the Mining Acts in Canada place upon the management of a mine the responsibility to ensure that provincial provisions are met. The "Federal Register" and mining companies parallel this arrangement in the United States. Equivalent legal

Jan 1, 1981

JIM ARNOLD: Questions? Comments? Gary, were you gone when I made the comments about corporate puke? [laughter] SPEAKER: You were hiding. BRUCE CAVENDER, BHP Copper: Having worked in both places, I'd like to address the issue of the plant versus the corporate office. One thing to keep in mind is that we are all very engaged with the technical elegance of a lot of the work we do. There's some tremendous technical expertise in the plant. But remember, the guys in the corporate office are only thinking in one denomination, and that's dollars. So we'll see something like a spill, and for us it's a problem. At the end of the day, what the corporation cares about is the financial impact. So we've got to be careful to couch our solutions in dollar terms. JIM ARNOLD: Rebuttal? [laughter] DOUG HALBE: Are you going to rebut this one, Andy? ANDY CARTER, Oxidor Gold Corporation: No, I don't think so. I'm not up to it. I'd just like to address a question both to our panel and the floor. Those of us who've been in this industry any length of time have seen these same mistakes made over and over again. Wherever you go, year after year, plant after plant, you see the same problems. I guarantee you, Doug, that if we have a similar conference down the road, you're going to see the same thing. My question to the panel and to the floor is what is it about our industry that stops us from learning from our mistakes? What characteristic is it that prevents us from learning and makes us repeat the same mistakes over and over again? DOUG HALBE: That's a great question. Someone said in a meeting 10 years ago that if the people who design plants designed airplanes, the planes would be falling out of the air all the time. GARY SIMMONS, Newmont Gold Company: I've got an answer to your question as to why many plants are poorly designed. It's that the minute anybody demonstrates any sort of competence in plant design, they're promoted to a higher-paying job, and the talent pool is left with people of lesser experience. Just think about it: The people who have the experience and have demonstrated it more than once have moved up. JIM ARNOLD: I think that there's another reason, too. Seven or eight years ago I was chairing a session, and I challenged everyone in the session to some day publish an article about the design mistakes they'd made because we never talk about our mistakes. I'll

Jan 1, 1998

By J. Donald Rimstidt, Jeanette K. Jerz

Acid mine drainage is a major environmental problem worldwide. A key to remediating this problem is understanding the rate and mechanisms of the complex, multistep pyrite oxidation reaction under geologically relevant conditions. Because many waste piles are not submerged, a large amount of pyrite oxidation actually occurs in air. We have designed a Barcroft-manometer reactor to measure the rate of pyrite oxidation in air as a function of relative humidity and oxygen partial pressure. The reactor consists of two chambers joined by a manometer. Each experiment occurs at constant temperature, initial oxygen partial pressure, and relative humidity, although these variable can be changed between runs. Oxygen consumption was measured and pyrite oxidation rates were calculated from those data. Initial data indicate that rate of pyrite oxidation by oxygen in humid air is much faster than the rate of oxidation by oxygen in solution. The rates determined by this study can be used to develop better remediation techniques for acidic mine waters.

Jan 1, 2000

By Wade W. Bristol

The Jerritt Canyon Joint Venture project is located about 80 km (50 miles) north of Elko, NV. It produces approximately 9.3 t/a (300,000 oz/year) of gold. The joint venture is 70% owned by Independence Mining and 30% by Meridian Gold. Independence Mining is the operator. The Jerritt Canyon Joint Venture started operations in 1980 by mining a series of open-pit mines. The discovery of deeper ores during early 1990s made it neccessary for the operation to mine a large portion of its annual production by underground mining methods. Underground production started in 1993 at the West Generator Mine. This was followed by the Murray Mine in late 1994. Two additional underground projects are being developed. Underground mining at Jerritt Canyon is scheduled to produce about 3.9 t (128,000 oz) in 1997.

Jan 1, 1997

By Henri Letient, Tom Aley, David Evans

Antamina is a large open-pit copper and zinc mine located within the Central Andes of Northern Peru at an altitude of 4300 masl. The facilities are situated within the headwaters of several watersheds, within the Amazon basin. Nearby villages rely heavily on springs and streams for drinking and irrigation water. The principle source of baseflow during the dry season is from Cretaceous karstic limestone aquifers. Antamina will produce nearly 1.4 billion tonnes of waste rock over its mine life. Finding suitable sites for storing large volumes of waste rock is often a challenging task – especially in karstic, alpine terrain. Detailed hydrogeological investigations are essential for delineating the karstic hydrogeologic watersheds associated with the proposed waste facilities, which are often very different than topographic (hydrologic) watersheds. Contamination vulnerability mapping at Antamina consisted of geological and karst mapping, geophysical surveys, geochemical testing, dye-tracer studies, drilling and aquifer testing. Detailed mapping followed by dye-tracer studies proved to be the most cost-effective methods for characterizing the karst aquifer systems. The results were used to optimize waste rock management at the site to minimize potential impacts on groundwater resources.

Jan 1, 2005

By Li. S. D., R. X. Zhang, K. M. Li, Y. D. Zhang, Y. J. Hou, S. G. Li

A computer aided design software system for long range coal surface mine planning has been developed by the authors. The system is composed of two subsystems: a coal deposite sub- system and a long range mine planning system. The geological parameters are estimated and a grid model is formed, then a 3-D block model can be developed for mining design. The long range surface mine planning system is based on oriented graph simulation and combined approaches to seek for the optimal deign alternative. This mining model consists of a number of sub-models to realize mining design functions such as: calculation of mining volume and coal quality by graph scanning; determination of operational stripping ratio by interactive design; varification of annual coal production; delimitation and development of dumping site; optimization of material flow direction and volumes by Linear Programming; surface mine production scheduling by interactive iteration; etc. The software package was developed on PC computer 486. It features classified menu guide, module structure, figure and graph representation on the screen and flexible interactive functions. This system has been applied to an open cut coal mine and predicted functions have been obtained.

Jan 1, 1996