Search Documents

By J. E. Chilton

Methanometers with catalytic heat- of-combustion sensors used in coal mines today will read low for flammable gases when oxygen (0,) concentrations are low or when methane (CH,) concentrations are greater than 10%. Thus, these methanometers may not be reliable during operations such as fire fighting or recovery of sealed mines. The U.S. Bureau of Mines developed a total flammable gas detector (TFGD) to measure CH, at concentrations up to 100% and to measure flammable gases in low 0, concentrations. This paper describes the operation and construction of the TFGD and discusses measurements of flammable mine gases obtained from a mine in western Pennsylvania.

Jan 1, 1992

By G. E. Burrer, D. Malhotra, T. E. Irwin, S. Johnson

Climax byproduct-plant tailing assayed 0.019% WO3. Pilot-plant and laboratory tests were performed to investigate the possibility of recovering additional tungsten values from the byproduct-plant tailing. The methodology used in the study and the results of this investigation are discussed.

Jan 1, 1987

By T. W. Camm

In this US Bureau of Mines report, mine and mill cost models are presented to make estimates of the cost to develop mineral deposits in the desert region of the southwest United States. Regression analysis was used to generate capital and operating cost equations for each model based on daily production capacity. These models are used for Potential Supply Analysis (PSA) studies by the Bureau, which analyzes the economic benefits of minerals in a region.

Jan 1, 1995

By Peter S. Schneidkraut

This paper will discuss the Final Tunnel Linings which were placed in 6700m of a 2.32m inside diameter precast concrete lined interceptor sewer tunnel in Staten Island, New York. Two methods were employed to install the final tunnel linings. One method involved forming and placing a polypropylene fiber reinforced concrete cunnette invert, followed by an arch pour. The second method involved the jacking of reinforced concrete pipe into the tunnel, followed by a low density cellular concrete backfill grout. These two methods will be described and compared.

Jan 1, 1993

By P. R. A. Andrews, G. Heinrlch, V. I. Lakshmanan

The paper describes a simplified method to chemically modify the surface of industrial mineral fillers. Four industrial mineral samples were taken from feedstock of commercial fine grinding operations. These samples were ground in bench scale ball mills and in the presence of various organic solvents. The ground products were measured for particle size distribution, surface area, surface chemistry by oil absorption and degree of organicJminera1 bonding. Where appropriate, the ground products were compared to commercially available surface modified, industrial mineral fillers.

Jan 1, 1990

By Robert T. Tape, Thomas G. Harper

Valley-fill heap leaches built in steep terrain over low-friction angle liner system may be unstable even though analyses indicate stable ore slopes. This paper demonstrates the potential for massive heap failure using stability analyses which consider both heap slope and heap mass failure considerations. The computations presented also reveal the sensitivity of mass heap stability to liner friction angles.

Jan 1, 1987

By Lynn B. Hales

Flotation performance varies widely as feed conditions change. Maintaining metallurgical targets has proven almost impossible without automatic control. Traditional control methods and procedures are inadequate. Using on-line x-ray analyzers, reagent control and accurate froth level control with flotation models and "Expert" computer control systems has improved metallurgical performance significantly. Examples of actual plant cases are described as well as the expert system methodology.

Jan 1, 1989

By L. G. Austin

Development of an equation for tumbling charge and balls plus comparison to plant data suggests that the net mill power for cylindrical semiautogenous mills can be calculated from

Jan 1, 1991

By D. S. Choi

This paper presents the results of geomechanics work applied to the longwall operation. The mining method was successfully adapted to US mining conditions resulting in an improvement in safety and productivity. The paper deals with various geomechanics problems associated with geologic and mining conditions.

Jan 1, 1987

By William F. Riggs

The characteristics of frothers can often be determined by the proper selection of various chemical groups. There are three basic groups utilized in the application of frothers. These are alcohols, polyglycol ethers, and polyglycols. Some of the chemical groups are separated in subgroups. Each chemical group provides particular characteristics which affect load support, bubble diameter, water retention, air dispersion, and kinetics of froth formation. These chemical groups may be preblended in various percentages to optimize frother characteristics for a particular ore deposit.

Jan 1, 1986

[Costs may be classified according to their source and behavior: Scale of aggregation - Total costs - Unit costs Time period for which the costs are charged - Product costs - Period costs Controllability and relevance for decision-making and control - Controllable costs - Noncontrollable costs - Sunkcosts - Opportunity costs Their basic source - Production costs (also termed manufacturing costs) - Nonproduction costs How the costs change with changes in activity - Fixed costs - Variable costs - Semivariable costs Traceability to individual units of production - Direct costs - Indirect costs Use in planning (budgeting) and subsequent control - Standard costs - Normal costs ]

Jan 1, 1999

By Robert Moore Lewis

A unit for separating minerals Into two prescribed size fractions, designated as a Lewis Hydrosizer, was developed at the North Carolina State University Minerals Research Laboratory Ore samples with different mineral compositions, including coal, were separated effectively with the laboratory continuous unit Commercial size units are in operation in North Carolina and Mexico, and under construction In Norway Additional units are being built or are in the planning stage at several companies.

Jan 1, 1983

By Colin C. Brooks

The Ok Tedi gold/copper deposit of almost 800 million tonnes was found in I968 because at that time technology had just developed sufficiently to enable exploration of such an area, world markets and prices for copper encouraged exploration for large deposits of low grade ore, Papua New Guinea law encouraged exploration by groups with men, money, management and expertise necessary for successful prosecution of such a search and such groups were already operating in the country.

Jan 1, 1990

By R. N. Tempel, M. Lengke

Arsenic sulfide (orpiment, realgar, amorphous AsS and As2S3) oxidation rates were measured in mixed flow reactors at pH-2 and at temperatures of 25 ° to 30 °C. The measured oxidation rates for arsenic sulfide solids by dissolved oxygen are in the range of 10-11 to 10-10 mole m-2s-1 after being normalized to final surface area. The order of arsenic sulfide oxidation rates decreases at pH-2 from amorphous AsS > realgar > orpiment > amorphous As2S3. Compared to pyrite, arsenic sulfide oxidation rates are approximately 1.5 to 15 times slower than pyrite oxidation rates at pH-2.

Jan 1, 2003

By Timothy J. Napier-Munn, David M. Weedon

A model of mineral liberation was developed using back calculation techniques to determine breakage/liberation parameters in a similar manner to the way breakage parameters are determined in the Population Balance Model (PBM). Comminution and liberation data was collected from grinding mills operating at Pasminco lead/zinc mine Broken Hill, and Mt. Isa Mines copper concentrator, Mt Isa, Australia. Laboratory scale single particle breakage tests on ore samples from these sites were undertaken using a twin pendulum breakage device. Break- age/liberation parameters were then determined for several mills using back calculation techniques. The liberation/breakage parameters were then used to simulate mill liberation performance under varying conditions.

Jan 1, 1996

By W. D. Mayercheck, A. G. Mayton, J. R. Bartels

Since 1982, the US Bureau of Mines has investigated improvements in protection for operators of thin seam shuttle cars. Due to working height restrictions in thin seam mines (=1.22 m or 48 in.). Federal mine regulations require that canopy protection on shuttle cars be provided only in mines =1.07 m (42 in.). However, court obtained variances are granted to mines =1 .22 m (48 in). This paper presents ongoing research to design and evaluate a uniquely positioned, ergonomic compartment for a shuttle car that provides the operator with full canopy protection in working heights of 1.02 m (40 in.).

Jan 1, 1990

By J. A. Organiscak

Data on dust-control practices, mining conditions and occupational exposures were gathered for approximately 80 underground continuous mining units. Despite silica contents on dust samples in excess of 5%, nearly forty units successfully maintained silica concentrations at or below 100 µg/m3 on a majority of occupational dust samples, while the remainder had difficulty maintaining this level. These two sample sets were termed Group A operations and Group B operations, respectively. This data was compared to identify causes of high occupational silica dust exposures. Analyses of dust-control parameters and geologies revealed only minor differences between these two groups. However, subsequent comparisons of face ventilation design showed considerable differences in silica exposure and silica content between Group A and Group B at the continuous mining machine and roof bolter operator occupations. These differences were minimal when using exhaust curtain ventilation with a dust scrubber. This face ventilation system can benefit operations having difficulty controlling silica dust exposure and silica dust content. The collected data also showed that occupational samples from Group B operations possessed generally higher silica exposures and silica content than similar samples from Group A. The single head roof bolter (helper) possessed among the highest silica exposures and silica contents in both groups.

Jan 1, 2002

By Y. C. Kim

One-quarter of a century has passed since the "theory of regionalized variables" (geostatistics) was introduced by G. Matheron (1962, 1963) in France. Yet, only during the past decade has geostatistics found broad acceptance in the mining industry. Foremost among the reasons for this time lag was ignorance. The first English treatise on geostatistics was not written until Matheron (1971), and the first published text accessible to mining professionals did not appear until David (1977). Other significant reasons for the slow acceptance of geostatistics included the conservative nature of management in the 1970s minerals industry, and the fact that conventional ore reserve estimation performs reasonably well when confined to massive deposits of base metal and iron deposits having relatively low coefficients of variation in grades. In short, mine engineers and geologists were not willing to accept a new set of tools for problems that they did not see.

Jan 1, 1989

By Ben H. Daud

A computer model has been developed at Consolidation Coal Co.'s Central Engineering Dept. for preliminary economic evaluation of deep coal mine reserves. Since it was first formulated more than two years ago, the model has been used for the following purposes: (1) ranking studies of coal exploration projects, (2) marketing surveys, (3) preliminary sale and acquisition analysis of coal reserves, and (4) parametric analysis in conjunction with detailed feasibility studies.

Jan 1, 1979

By K. N. Han, J. J. Kellar, Y. Guan

The adsorption of zinc species onto silica in ammoniacal solutions was studied. The adsorption isotherms indicated that the adsorption of zinc increased with increasing pH. The adsorption density increased as the zinc equilibrium concentration increased up to =3.5x10-4 M. Above this concentration, the adsorption density was independent of the equilibrium concentration, and a maxima adsorption density was reached. Temperature had no significant effect on the adsorption density.

Jan 1, 1995