Search Documents

"Quang Ninh province is located in the north east of Vietnam and the coal mining in the province generates two thirds of the province’s GDP. The coal is extracted from both open pit and underground mines for the country’s complete coal export and by a share of more than 90% for domestic coal usage. Overburden generated through open pit mines is piled up nearby in the form of large waste rock dumps. The side-hill fill dumping near open pit mines is the source of environmental degradation in the region. Among the current problems at solid waste rock dump sites are dust emissions during and after dumping as well as Acid Rock Drainage (ARD). One of the major existing problems at waste rock dumps is dump stability (comprising erosion, sliding and subsidence issues). The RAME R&D project (Research Association Mining and Environment in Vietnam) is - among other activities - actively involved in the research for stabilisation and rehabilitation of mine waste rock dumps in Vietnam in the form of several sub-projects. The Institute of Mining Engineering I of RWTH Aachen University is leading the sub-project of mine waste dump stabilisation in co-operation with Chair of Geotechnical Engineering and Brenk Systemplanung GmbH. Mine waste dumping in the form of layers as an alternative to the side-hill fill dumping is expected to bring up environmental and economical benefits by minimising the problems of dump sites with the contribution to a sustainable development. Reduction of the post construction settlements, long term stable dump profile with minimum erosion, improvement of material parameters for geotechnical slope stability through compaction from hauling trucks as well as economical evaluation of new dumping concepts are the areas of the current research. The project has been financed by German Federal Ministry for Research and Education (BMBF). The ultimate aim of the sub-project is the compilation of the project results in the form of a "Best Practice Guide" and software based "Decision Support System" for planning and management of solid mine waste dumps."

Jan 1, 2011

By J. R. R. Bowling, A. McFadden, M. Francoeur

The abstract discusses the increasing use of extensive duct-fan systems in underground hard-rock mine development. It highlights the challenges of designing these systems, particularly the risk of partial vacuum and the need for careful booster fan positioning. The paper explores factors influencing the design of these systems, including component limitations, operational wear margins, and power constraints. It also defines the concept of partial vacuum and its impact on ventilation ducts. The authors propose an algorithmic approach for specifying the location and blade pitch of in-line booster fans to prevent system failure.

Mar 17, 2022

By John G. Whellock, Kevin A. Foo, John H. Canterford, Karen E. Sobel

Nitric acid has long been known as an effective oxidant. Nitric acid leaching is characterised by highly favourable kinetics. Process development was impeded due to the corrosive nature of the process, limited knowledge of acid recycle and complex reactions which are still not fully understood. In 1981, Arseno Processing Ltd (APL), began development of the so-called Arseno process. The technology targeted nitric acid oxidation of refractory gold ores and concentrates whose refractoriness was due to the presence of sulphide minerals. APL lodged patents in United States, Australia, Canada and several other countries covering the basic chemistry, the overall process, and reactor design. The name Arseno led to the misunderstanding that the process was only applicable to arsenic-bearing material. The name was therefore changed to the Redox process in 1988. Having played an important role in the development of Redox from 1986, SASOX recognised the great potential of the process and purchased the process in 1990. SASOX owns all the patents and other Redox proprietary know-how, licensing agreements in force, and is committed to the ongoing development and commercialisation of the Redox technology. Minproc has been granted specific marketing and engineering rights to the Redox pro_cess.

Jan 1, 1992

By E. C. Westman, W. R. Thomas, W. J. Conrad, A. J. R. Russell

"Understanding ground control problems continues to remain a focus of the mining engineering community. To aid mine operators and engineers in identifying and responding to ground control issues, the Ground Observation System (GOS) is being developed. The GOS is an integrated, web-based graphical user interface that displays ground response data collected wirelessly from an underground mine. It presents data in an intuitive manner to assist mine personnel, who are on- or off-site, in quickly identifying hazardous areas. Geotechnical instrumentation will be connected to wireless transmitters that will relay data in real-time to a surface computer that stores the information in a database. The GOS website will then display the geotechnical data in graphical and tabular forms, as well as in conditionally formatted mine maps. Data from each measurement device will be able to be viewed in its entirety or within a time interval, and can be downloaded for further analysis. The ability of the GOS to quickly interpret and communicate mine hazards to personnel of varying technical ability should prove to be a useful tool in understanding ground control and thus improving mine safety.INTRODUCTION Computer-based data information centers that convey operating parameters and conditions are prevalent in modern underground mines. Today’s systems are popular in showing ventilation controls and monitoring equipment performance (Jyothi & Meena 2013). In ground control monitoring, Conover, Ross, and Bigby, 2010 have installed a wired telltale roof monitoring system that sends roof displacement data every ten minutes to a computer on the surface. The computer receives, stores, and displays the data in real time. Data can also be viewed remotely through a password protected internet connection. Additionally, an internet connection allowed for remote updates to the system which streamlined software development and maintenance by eliminating travel (Conover et al., 2010). Currently, no such system beyond Conover et al.’s design has been accomplished. The Ground Observation System (GOS) is being developed to fill the void of real-time geotechnical monitoring in underground mines. A wide array of data will be transmitted wirelessly and broadcasted to on- and off-site mine personnel through the internet. The GOS will incorporate geotechnical data from roof deformation, borehole scratch testing, photogrammetry, and seismic monitoring into one interface, all while achieving permissibility for the use in gaseous mines. As a result, a comprehensive view of rock movement due to mining will be available. The overall purpose of the GOS is to deliver warnings; to ensure reliable data is relayed to personnel for the identification of potential ground failures, provide mine engineers information to design more stable mines, and assist with further geotechnical research."

Jan 1, 2015

By Dávila-Pulido. G., L. Magallanes-Hernández, F. López-Saucedo, J. Batista Rodríguez, A. Uribe-Salas

"This paper presents the results of tests performed to study the effect of slurry solids concentration on the behavior of gas dispersion in industrial-scale mechanical flotation cells. The experiments were conducted at five concentrator facilities run by a Mexican mining company, specifically in the rougher bank of the lead/zinc flotation circuits. Those mechanical cells having significant contribution to the performance of the circuit, that is, the cells that enable high recovery, were characterized. The measurement protocol enables measurement of the superficial gas velocity, gas holdup and bubble size, and sampling of the mineral slurry. The measured data indicate that bubble size and gas holdup decreases as the concentration of solids increases. IntroductionThe process of mineral concentration by flotation is based on contact between particles and air bubbles, the selective adhesion of hydrophobic particles onto the bubbles, and the rising of the bubble-particle aggregates to the surface of the flotation cell to overflow over the lip to form the concentrate. It is now accepted that the physical and chemical process variables that control the flotation of hydrophobic particles are closely related to gas dispersion (Schwarz and Alexander, 2005). Gas dispersion is defined by the superficial gas velocity, Jg (Torrealba-Vargas, Gomez and Finch, 2006), the gas holdup, eg (Tavera, Gomez and Finch, 1997), the bubble size, d32 (Dobby and Finch, 1986; Gorain et al., 1995; Hernandez-Aguilar et al., 2004) , and the bubble surface area flux, Sb (Manqiu and Finch, 1989; Manqiu, Finch and Uribe-Salas, 1991). In recent years, the advances that have been made in sensor technology have enabled the characterization of gas dispersion in industrial flotation cells with excellent results (Gomez and Finch, 2007). This technology advancement has allowed the gaining of a deeper understanding of such complex mechanisms as carrying capacity (Yianatos and Contreras, 2010), collection efficiency (Gorain, Franzidis and Manlapig, 1997; Massinaei et al., 2009) and bubble coalescence (Finch, Nesset and Acuña, 2008; Zangooi, Gomez and Finch, 2010)."

Jan 1, 2017

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012

By S. Bargigli, S. Ulgiati, M. Raugei, F. Cherubini

Metallic magnesium is mostly used in lightweight alloys in order to decrease fuel consumption in automotive applications. Several different production processes are currently used worldwide, and the magnesium production scenario is changing rapidly, with Chinese production increasingly dominating the world market. For the purpose of this paper, a novel approach to Life Cycle Assessment was applied, in which Material Flow Accounting and energy-based methods (Embodied Energy, Exergy and Emergy Analyses) are integrated and complemented, with a detailed description of the environmental hazards associated with emissions from all the different processes.

Jan 1, 2005

By C. R. Stephan

Explosion-resistant seals in underground coal mines isolate the environment within the sealed area from the active workings of the mine. The current United States Title 30 Code of Federal Regulations (CFR) requires these seals to be constructed of solid concrete blocks. The CFR also allows for alternative methods or materials to be used to create a seal if they can withstand a static horizontal pressure of 138 kpa (20 psi), provided the method of installation and the material used is approved in the ventilation plan. The purpose of this report is to identify those explosion- resistant seals that have been tested and meet or exceed all the requirements of the CFR.

Feb 24, 1997

By Joan Carles Casado Ortega, Mitchell Gerdtau, Sandeep Pyakurel, Eric Crocker, Frank Perrone

The Parallel Thimble Shoal Tunnel (PTST) project is a part of the Chesapeake Bay Bridge- Tunnel (CBBT) complex. The project involves the construction of a two-lane bored tunnel under the Thimble Shoal Channel between Portal Island #1 (the southernmost island) and Portal Island #2. The new PTST will be the rst transportation tunnel constructed in the Mid-Atlantic region by a tunnel boring machine (TBM). This paper describes the design and construction of the tunnel approach structure in an open marine environment with the strategies employed to overcome the various construction challenges. The project is unique since the entire tunnel approach structure is built on a very limited area within an open marine environment without any reclamation of the existing island.

Jun 23, 2024

By D. Bogh

Wound rotor motors are used in difficult mining applications where there is a need to start high inertia, hard starting loads while limiting inrush current They are recognized as robust and simple to control. This paper will cover the performance, specification, and important issues to be considered when applying medium voltage wound rotor motors in mining applications. Medium voltage grinding, crusher, and conveyor applications will be discussed. Specifically covered are motor efficiency, speed range, and rotor control. Crane motors often have wound rotor construction, but their load cycle and ratings are outside the scope of this paper.

Jan 1, 2011

By D. M. Schubert

As a clean and renewable energy carrier, hydrogen is an important component of most alternative energy portfolios. Hydrogen combines very high energy content by weight with excellent environmental attributes. Since hydrogen reacts with oxygen to produce only water with release of energy, it can be used to power fuel cells, combustion engines, and turbines, without production of greenhouse gases at point of use. However, because of its low volumetric density, storing pure hydrogen is impractical. Thus implementation of hydrogen technologies requires materials that can safely store and release large amounts of hydrogen (1,2). In recent years, the U.S. Department of Energy (DOE) and other governmental agencies around the world sponsored extensive research on hydrogen storage materials, including those based on boron. These efforts have resulted in significant advances in hydrogen storage technologies. Boron materials stand out as leading candidates for hydrogen storage among the many options investigated. Combining excellent hydrogen densities, release rates, and safety characteristics, some boron materials can hold substantially more hydrogen by weight and volume than even pure liquid hydrogen (3-5).

Jan 1, 2010

By E. M. Spokes

Starting in 1980, a committee of the National Research Council studied the question of why some underground coal mines are safer than others and what could be done to improve the ones with poorer performance. The results indicated that safety is improved by management commitment to safety, by cooperation between labor and management on safety matters, and by quality training of employees and managers. Younger miners have higher accident frequencies, but are less likely to be killed or permanently disabled by a lost-time accident. Methods for improving safety performance are proposed.

Jan 1, 1987

By W. G. Lawrence

The rapid development of science and technology in Russia has been the result of well laid plans since 1918. At that time the Institute of Silicates was established is Moscow and later the establishment of similar more specialized institutes for the study of cement, glass, refractories, construction ceramics, electrical ceramics, building materials and asbestos provided the necessary research facilities for studies related to all types of ceramic inorganic materials. The' Institute of Ceramics and the Institute of Silicate Chemistry, Academy of Sciences, USSR, were founded in Leningrad. The work now going on in these various research' institutes covers every branch of silicate science and ceramics The impetus behind such establishment of special¬ized laboratories is no doubt due to the 5-year plans and the necessity of improving the scientific knowledge regarding the materials being used and the products being manufactured.

Jan 1, 1960

Preface The intention of this paper is to provide the reader with knowledge gained here at Memorial University regarding the practical use of the Bruker SDD x-ray detector for applications in image analysis. Included below are descriptions of the detector’s characteristics and observations regarding precautionary use. What is described below is relevant to the XFlash® model 3001 detector only, whereas the model 4010 is the new and currently available detector. The manufacturer has provided up-to-date information and a figure that presents very different behaviour relative to the characteristics described in this paper. That information and figure is also included here as an addendum (see figure 9). Introduction It has been more than two decades since an image analyzer has been proposed based on the unique imaging characteristics and spatial resolution provided by the scanning electron microscope (SEM) together with energy discriminating x-ray (EDX) acquisition (Reid et al, 1984). From the inception of technique, technology of the day has played the major role for making applications increasingly more practical. Computers, digital imaging, and softwares together with computer automation of modern digital SEMs have all played their part in advancing the technique to where it is today.

Jan 1, 2007

In February 2001, Kalgoorlie Consolidated Gold Mines (KCGM) commissioned its first full-scale ultra fine grinding (UFG) plant to supplement existing roaster concentrate treatment capacity. This process involves the fine grinding of refractory pyritic concentrate to 10µm, followed by direct cyanide leaching for the recovery of gold. By this means gold is economically extracted from the concentrate without the need to first oxidise the host pyrite. This paper details the history of the project from initial laboratory testwork comparing possible treatment options, to current performance of the 12 tph plant. This includes the cost comparison of the major treatment options, the laboratory and pilot scale UFG performance, the UFG mill selection, cyanide leaching of UFG product, commissioning and plant performance to date.

Jan 1, 2002

By James F. Kvitkovich, George V. Weisdack

Longwall mining techniques were introduced into U.S. bituminous coal mining operations in the early 1960s. These techniques were gradually adopted by many mines during the 1970s. By 1983, considered to be the peak of the longwall mine census, there were 118 active longwall faces in 79 coal mines throughout the United States. Beginning in 1984, longwall faces began a decline in numbers that has continued to the present day (Fig. 1). The geographic distribution of longwall faces today is shown in Fig.2 according to region. A breakdown of recent longwall mine production by region is shown in Table 1. An approximate breakdown of present longwall face installations by product (metallurgical and steam) is shown in Table 2.

Jan 1, 2005

By Kexin Cai, Isidro Rivera, Shawna Von Stockhausen, Maria Chastka, Kevin Huynh

The Newell Creek Dam Inlet/Outlet Replacement Project is located approximately 11 miles north of Santa Cruz, California along Highway 9 in the San Lorenzo Valley. This project will replace the existing inlet/outlet works at the Loch Lomond Reservoir by constructing a tunnel using conventional excavation methods while simultaneously drilling three intake shafts to intercept the tunnel from within the city’s water supply. This project will improve the system’s overall operational efficiency and performance, and provide a safe and reliable facility for the City of Santa Cruz’s drinking water supply. This paper discusses the overall project configuration, construction observations, and challenges during construction, including tunnel excavating through the marine sedimentary siltstone of the Monterey Formation, probing and pre-excavation grouting, and the tools utilized to manage the project.

Dec 1, 2022

By J. A. Marts, R. C. Gilmore, S. Saki, J. F. Brune

Computational fluid dynamics (CFD) modeling involves the creation of a computation domain called a mesh or grid to solve the equations defining the physics of fluid flow. This process often comprises the majority of time spent in modeling efforts. In a project sponsored by the U.S. National Institute for Occupational Safety and Health (NIOSH), researchers at the Colorado School of Mines used an innovative meshing approach, allowing easy adaptation of the CFD model to adjust to a variety of longwall bleeder-ventilated and progressively sealed (often referred to as bleederless in the United States) mining geometries, with gob porosity and permeability scalable over a wide range. This paper presents the methodology of the meshing and scaling approach along with recommendations for using CFD modeling in longwall gob ventilation applications. The new meshing technique was utilized to evaluate the function of a back return in a progressively sealed gob and a bleeder-ventilated gob.

Jan 1, 2014

By Kevin Saeler, Patrick Willaman

Utilizing automation is one way to improve competitiveness. Roof and rib bolting in underground coal mines has not changed significantly for more than 40 years. Most roof bolting is still a largely manual process involving high levels of staff carrying out repetitive work. Roof bolting statistically has one of the highest levels of underground accidents, including finger, hand, and arm injuries. Operators are exposed to falling objects and becoming entangled in roof bolting apparatus while roughly moving awkward 6-ft drill steels and roof bolts. It is estimated that over 25 million roof bolts are installed annually in the U.S. underground coal market with well over 1,500 operators involved in roof bolting on a day-to-day basis. Recently electrohydraulic roof bolting rigs have been installed to offer partial automation of the drilling cycle and the bolting cycle. The next stage is to provide a storage and loading system to allow full automation of fullcolumn resin roof bolts. This paper reviews the latest electrohydraulic roof bolting equipment and discusses the testing of a fully automated drill rig. Full electronic control allows each step of the roof bolting process to be recorded, providing a digital record of each installation, including hole depth, spin time, gel time, torque, and cycle time. Other benefits include monitoring of water pressure and flow, used to prevent blocked drill steels as well as digital fault finding. A fully automated roof bolting machine greatly improves operator safety and gives high-quality repeatable roof bolting with reduced cycle times.

Jul 1, 2023

By H. E. Rudi

The advent of open nit mining permitted the development and processing of minerals never before thought possible. New equipment was needed; new techniques were devised; new methods were called for. This development and acquisition of new techniques, methods and equipment did not, however, stir the souls of our industry and educational leaders sufficiently to a recognition of the problem of people, especially the future development of the people needed in open-pit mining. The people problem has been and will be with us as long as there are two of them. The development of people will be required for the same reason. The problem of developing future personnel for open-pit mining is not what must be developed; that is known to all of us and can be briefly stated ashore and better of everything." As I see it, the real problem lies in determining (1) what personnel are really critical, (2) why are they critical and (3) how can we develop them.

Jan 1, 1965