Search Documents

By S. J. Swan

A computerized on-line process control system designed to monitor and control the seven-cone copper precipitation operations at Kennecott Copper Corporation's Chino Mines Division in New Mexico has been continuously operating since April, 1972. The cone monitoring system consists of plant sampling components, process measurement instrumentation, on-stream X-ray spectrometer, control computer, typewriters for programming and for operating reports, foreman's communication console, and cone automation hardware. The system provides the following functions: (1) assays for copper and iron from ten process streams on a continuous rotating basis, (2) directs hardware to automatically flush and start up cone units based on measured performance variables, (3) provides continuous plant operating data and calculates metallurgical averages as well as production figures for shift and daily summaries, and (4) provides data logging capabilities. The system is very reliable and improves plant performance by increasing yields, reducing scrap iron consumption, and reducing operating manpower requirements.

Jan 1, 1975

By J. W. Choung, J. A. Finch

Acid rock drainage (ARD) is a recognized environmental challenge facing mining industries. An ambient temperature ferrite (ATF) process has been investigated for treating ARD. Most nonferrous metal and calcium ions present in typical ARDs were found to be detrimental to the ATF process. Three approaches were examined, including C02 aeration, addition of complex agents and use of magnetic seeds. By introducing magnetic seeds in the ATF process, the interferences were minimized and all the precipitates formed with lime neutralization were magnetically recovered from a simulated ARD. The residual concentrations of major metal ions in the treated water were environmentally acceptable. The XRD pattern confirmed the spinel ferrite crystal structure of the products

Jan 1, 2000

By J. Ragot, D. Maquin, N. Heraud

Acquisition of coherent and representative data about the state of processes remains a major problem of process control. This paper proposes an approach that ensures coherence in measurements on an operational industrial process. The basic technique employed relies on balance equilibration of resource mass flow. An interesting particularity of the set up is the ease with which it can be adapted to check productivity or detect sensor failures. In the case of sensor failure, it suffices to examine the evaluations before and after balance equilibration. The algorithm was tested by means of computer simulation using data from an industrial metallurgical flowsheet.

Jan 1, 1992

By Laurent Rus, Bakar Amara, Jean Habimana

The La Fontaine Tunnel in Montreal, Quebec is currently undergoing major structural rehabilitation work and systems upgrade work to comply with current codes, standards and best practices in fire life safety and to extend its lifespan of this 55-year-old immersed tube tunnel for at least another 40 years. The paper discusses design consideration of ongoing works that include structural analyses to evaluate repair strategies for the post-tensioned reinforced caissons, the scheme to repair two leaky joints between caissons, the design of passive fire protection that involved in situ and real scale laboratory tests, and other tunnel systems upgrades.

Jun 13, 2023

By T. E. Bernard

"Refuge alternatives (RA) provide shelter to miners trapped underground during a disaster. RA manufacturers must demonstrate that their RAs meet the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and the management of heat that results from the RA occupants and mechanical/chemical systems. In this study, miner size and activity level were used to determine the metabolic heat rate, oxygen requirements, and carbon dioxide generation that is representative of miners in a refuge situation. A convenience sample of 198 male miners was used for the distribution of current US coal miners, and the composite 95th percentile height and weight were determined to be 193 cm (76 in) and 133 kg (293 lb). The resting metabolic rate (RMR) was determined to be representative of activity level in an RA. The highest likely metabolic heat generation ranged from 115 W to 135 W, depending on RA occupancy. The highest required oxygen supply and carbon dioxide removal were estimated to be 23 LO2/h/person (0.81 ft3/h/person) and 20 LCO2/h/person (0.71 ft3/h/person), which means the margin of safety is 50% or more when compared to the MSHA requirements. INTRODUCTION Refuge alternatives (RAs) provide shelter to miners trapped underground during a disaster. Manufacturers must demonstrate that their RAs meet Mine Safety and Health Administration (MSHA) requirements for the supply of oxygen, the removal of carbon dioxide, and the management of heat that results from the occupants and the mechanical/chemical systems in the RA [1]. These MSHA requirements were based on a standard 70 kg (168 lb) male with an assumed allocation of activity of 80% rest and 20% moderate activity level [2]. The purpose of this paper is to re-examine the metabolic heat generation and oxygen and carbon dioxide requirements of miners in an RA based on actual miner size and more realistic RA activity levels based on current RA designs. The purpose of this paper is to re-examine the Mine Safety and Health Administration (MSHA) requirements for oxygen supply, carbon dioxide removal, and heat generation. To achieve this, researchers took the following steps to estimate the metabolic demands and the associated heat generation, oxygen requirements, and carbon dioxide production. 1. Characterized the anthropometric characteristics of the miner population. 2. Described the metabolic rate profile of RA occupants. 3. Characterized the maintenance demands of RAs. 4. Summarized oxygen supply and carbon dioxide removal volumes. ANTHROPOMETRIC CHARACTERISTICS OF MINERS The weight, height, and age distributions of the adult male populations are summarized in Table 1. For each data set, the reported mean and standard deviation are provided. The 95th percentile (%ile) value for height and weight for each population was the mean plus 1.64 times the standard deviation."

Jan 1, 2017

By Jack Garrity

The Asarco Mission Complex includes two milling operations around a large open-pit copper mine in southern Arizona. The ore body was discovered in 1953 and the complex has been in operation since 1959. The mills provide the concentration operations of crushing, grinding, flotation and filtering processes involved in processing copper ore. Smelting and other downstream processing are accomplished at other Asarco locations. The mine pays a smelting charge to the smelter, which is seen as a service to the concentrators. The higher the concentration of copper to the smelter, the lower the smelting charge is to the mine.

Jan 1, 1995

By S. S. Hsieh

As part of a program to address long-term needs for ensuring adequate supplies of domestic phosphate raw materials, the Tennessee Valley Authority (TVA) has conducted considerable research on dolomitic phosphate rock beneficiation. The discovery that alkyl diphosphonic acids act as phosphate mineral depressants led to the development of several processes involving a carbonate flotation step for the effective beneficiation of these problem ores. Most recently, a partial de-oiling process in which the reagent consumption is greatly reduced has been developed. The reduction is achieved because part of the initial feed is beneficiated without passing through the separate carbonate flotation step. Using this method, a phosphate product containing 30.6-30.9% P2O5 and 0.7-0.8% MgO was obtained from a Florida dolomitic phosphate pebble which contained about 23% P2O5 and 2.0% MgO. The P2O5 recovery was 80.8-86.5%.

Jan 1, 1989

By H. V. Scotland III

Lafarge Corporation's Texas Quarry, in Baltimore MD, achieved a substantial expansion of pit reserves by removing an inactive underground mine. The day lighting program, designed, and completed in 1997, open pit mined more than 400 meters of room and pillar workings which were originally developed to recover high brightness Calcium Carbonate. The project proved to be a challenge throughout its course as the pit plan was modified and successful daylighting techniques were developed to remove the mine without adversely affecting the safety of the operation, quality of the stone recovered, or negatively impacting the surrounding community. The design parameters and techniques developed and implemented at Texas may prove of interest to other operators as they are faced with daylighting opportunities. This article will detail the challenges we faced and the solutions which made the project a success.

Jan 1, 1999

By R. J. Snoby, P. Grotjohann

In processing heavy-mineral sands, the low feed concen¬tration and respective high value of the desired minerals require high-capacity production and sharp classification/ separation techniques to reduce the specific production costs. This paper describes the new allfux® separator, which can economically accomplish these criteria. The separator is a two-stage process that combines rising current and fluidized-bed technology. This allows for the treatment of ex¬tremely high mass flows in a single unit. This paper reports on test work performed on coal, iron ore and heavy minerals.

Jan 1, 2000

A bearing isolator is a noncontact, nonwearing, permanent bearing protection device. It has a rotor and a stator, and the two are unitized, so that they do not separate from one another while in use. The rotor turns with a rotating shaft, while the stator is pressed into a bearing housing. The two components interact to keep contamination out of the bearing enclosure and the lubricant in. Bearing isolators do not require lubrication or any particular shaft finish or condition. The best bearing isolators are made of metal, usually bronze. They use a vapor-blocking feature that inhibits the free transfer of vapor contamination when the rotating equipment is cycled on and off.

Jan 1, 2004

By Prasannarao Dontula, Kal V. S. Sastry

Advances are made in the field of mineral processing on a continuing basis both in the industry and the academia. These advances do not always get used fully because of the inherent difficulties in the transfer of knowledge and reduction to practice. In recent years, knowledge engineering is being increasingly employed in other fields to overcome some of these difficulties. This paper presents a vision of how knowledge engineering can be applied to the benefit of the mineral processing industry and includes a discussion of associated principles, techniques, and advantages.

Jan 1, 1993

By C. C. Bailie

This paper will be concerned with those mineable coal measures at depths necessitating deep mine operations in the range of 200 feet to 800 feet in depth. The area is generally classified as the Southern Illinois Field but more specifically includes that part of the state south of a line extending from St. Louis, Missouri on the west to Vincennes, Indiana, on the east. This embraces an area which presently includes a total of 38 shipping mines and 5 local or truck mines. Of these shipping mines, 22 are deep (shaft or slope) mines and the remaining 16 are strips. The average annual production of the shipping mines is around 29 million tons. The presently classified mineable reserves of the area are estimated at around 70 billion tons.

Jan 1, 1964

By R. D. Grove

The control of Florida phosphate flotation plants is largely based on the visual observations of experienced operators, both in recognizing good and bad froth conditions and in making judgments about the composition of feed, concentrate and tailing streams. Chemical analyses lag the process by at least two hours and, therefore, only assist in recalibrating the operators' vision when major deviations occur. An image analysis system was developed by IMC Fertilizer to improve the accuracy and precision of the composition estimation process. It still relies on the operator taking a representative sample, but provides a measurement in about 15 minutes after that sample is obtained. Background The search for a quick and inexpensive technique for estimating phosphate flotation stream composition continues. There have been attempts at using "wet chemistry," nuclearmagnetic resonance, neutron activation, X-ray diffraction and other techniques reported on in the past several years. None of these have yet found its permanent place in the flotation plants of the Florida phosphate industry. IMC attempted to use wet chemistry to provide 7.5-minute estimates of final concentrate insol and tailings BPL. This was aborted after 36 months of plant operation due to the high operating costs for chemicals and an operator. There was also no significant economic improvement in the plant's operation. Another factor was the necessity to limit these crude analyses to only a few process streams, which were insufficient to achieve improved plant operation.

Jan 1, 1993

By V. B. Achanti

Laboratory studies were carried out at West Virginia University to investigate the rock fragmentation mechanism by continuous miners using an automated rotary cutting simulator. The primary factors influencing the: fragmentation process were found to be: bit spacing, bit geometry, depth of cut, and cutting drum rotational speed. This paper presents the influence of these parameters in achieving optimum energy consumption and minimizing dust generation during rock fragmentation process. Three bits were used simultaneously on Indiana limestone while the bit tip angle was varied from 60° to 90°. Bit spacing was varied from 2.54 cm (1 in.) to 5.08 cm (2 in.) while the cutting process was assessed for varying cutting depths. Respirable dust generated during the course of the experiments was analyzed utilizing cascade impactors. Assessment of these parameters has led to a better understanding of the cutting mechanism by continuous miners in terms of energy consumption and dust generation.

Jan 1, 1997

Continuous improvement has become the watchword of the 1990s for most iron-ore-processing operations. In many instances, this improvement has been achieved through stepwise application of advanced control techniques to optimize operations. The benefits of this stepwise application have been great. However, they have fallen short of the full potential offered by the prospect of overall plant optimization. The successful integration of computers, instrumentation and control software throughout a plant promises to deliver an additional 3% to 5% of productivity in even the best-run plants (Herbst and Bascur, 1984). LKAB is Europe's largest iron-ore producer and a leading implementer of advanced control technology. In the late 1980s, LKAB introduced advanced control in its concentrator at Kiruna, Sweden to improve plant performance through higher productivity, greater efficiency and lower costs at each processing step.

Jan 1, 1995

By J. G. Groppo

A beneficiation process has been developed to provide selective separation of unburned carbon from high LOI fly ash. Previous reports of utilizing froth flotation to achieve selective separations required long residence times and high reagent costs. A proprietary reagent system has been developed to address both of these limitations. Based on the results obtained from laboratory and pilot-scale investigations, a flowsheet design has been developed to produce two distinct usable products from class F fly ash; low LOI ash and a high carbon product suitable for reburning or further upgrading. A process flowsheet and description are presented.

Jan 1, 1996

By I. WILKOMIRSKY, J. BECKER, F. Parada

Purification of molybdenite concentrate from copper concentrates was performed by sulfation. The sulfation of molybdenite concentrates was carried out with pure sulfuric acid (> 96%) at 160–190 °C to study the influence of the reaction temperature and reaction time on the residual copper in the molybdenite concentrates. A purified concentrate with less than 0.1 wt% copper and low levels of other metals were obtained. For up to 7.1 wt% copper, the conditions required are a temperature of 190 °C, a reaction time of 14 h, and a moly/acid weight ratio of 1/1. Furthermore, several designs of sulfation reactors were evaluated in order to obtain the desired level of copper in the product and to analyze the influence of the operational and design parameters on the reactor dispersion number (Le). The basic design for an 80-t/day plant fed with 4 wt% copper molybdenite concentrate requires five backmixed reactors in series, each measuring 8 m3, operating at 190 °C and with a reaction time of 10 h. The reactor must be protected against severe corrosion by the hot sulfuric acid with either Teflon, glass or ceramic.

Jun 14, 2022

By John D. Nelson

Unprotected uranium mill tailings impoundments can pose a significant risk to nearby inhabitants and the surrounding environment in the event of a prolonged or catastrophic release of contaminants contained in the tailings. As a result of this potential, reclamation plans for such facilities must include engineering designs to protect against disruption of the tailings and the potential release of radioactive materials. The goals for such engineering designs should be to provide overall site stability for long-term periods with no need for planned ongoing maintenance and to provide a repository for the tailings that will not place a burden on future generations. Although the goal is to provide a maintenance-free system that does not require monitoring, it must be recognized that some period of surveillance would be reasonable. The surveillance period could be relatively short and only needs to assure with reasonable confidence that the reclamation scheme that was implemented is functioning adequately. An investigation was conducted by Nelson, Volpe, Wardwell, Schumm and Staub (1983) entitled Design Considerations for Long-Term Stabilization of Uranium Mill Tailings Impoundments (NUREG/CR-3397). This report assesses the degree of confidence with which long-term reclamation plans can be expected to remain effective over specific periods of time, and to assess the additional effort required to extend the design period from one long-term period to a longer one. This paper presents a summary of that investigation and discusses some of the important conclusions.

Jan 1, 1984

By S. Mendenhall

The Golden Sunlight Mine (GSM) began operation in 1982 with a strong commitment to environmental stewardship and the local community. This commitment ensured the long-term physical, chemical and ecological stability of the mine site and maintained an active partnership with local stakeholders. Concerns for economic development intensified as mine closure loomed on the horizon and fostered the inception of the Community Transition Advisory Committee(CTAC).This coalition of interested area stakeholders has the primary focus to sustain current mining operations while concurrently seeking alternative post-mine economic development opportunities utilizing existing mine assets. Accomplishments include development of an Asset Re-utilization and Post-closure Plan, a community survey regarding the impending mine closure, recruiting an international wind energy company to develop a wind farm, and development of an industrial/business park. The synergy of this strong partnership is key to meeting sustainability goals and enhancing potential future mining operations. The cooperative effort of the GSM and the local stakeholders is a success story that could be a role model for other mining operations.

Jan 1, 2004

By Hendri Silaen, Ishak Degei, Nicoll Soumilena, Arwin Edijanto, Avesiena Primadiansyah

PT Freeport Indonesia’s Deep Mill Level Zone (DMLZ) is one of three operating cave mines at the Grasberg mine complex. The DMLZ is situated in the East Ertsberg Skarn System (EESS). It is set 500 m below the operating DOZ mine and located approximately 1,500 m below the surface, making it one of the world’s deepest panel caving operations. Initial undercutting of the DMLZ commenced in the second half of 2015 and has expanded to more than 120,000 m2. High pre-mining stresses and the changes associated with caving, combined with a strong and brittle rock mass, led to significant seismicity and rock bursting. Stress and seismic management are the main challenges for the operation and have evolved significantly from initial undercutting to the present. Considerable amounts of empirical data associated with ground response have been collected, evaluated and combined with historical lessons learned from the Intermediate Ore Zone (IOZ) and Deep Ore Zone (DOZ) mines, which are located within the EESS. This has provided an improved understanding of how the various geological, geotechnical and mine design criteria relate to one another. Additionally, the information has allowed for the development and implementation of improved strategies for stress and seismic management in the DMLZ. This paper describes how these learnings have driven changes in mine geometry, layout, and support systems. Through comprehensive monitoring and detailed inspections, positive changes have been seen in the ground response, leading to an increase in footprint reliability and accelerated cave growth. The paper summarizes the key learnings at the DMLZ regarding stress and seismic management as well as the positive improvements towards sustained and safe caving operations in the DMLZ.

Apr 26, 2022