Search Documents

By Keith G. Wallace, Malcolm J. McPherson

In order to model accurately a mine ventilation system in an existing mine, it is necessary to determine the resistance to airflow in all main airways. This is accomplished by measuring the airflow and pressure differential in each airway. Gauge and tube methods have been used to determine pressure drops in ramps and level airways. However, it has rarely been used in evaluating the frictional pressure drop in shafts. Because shafts commonly have the highest pressure loss in mines, it is critical that the resistance of these airways be determined accurately. This paper describes the theory and practice of using the gauge and tube method for determining the pressure drop in shafts. The pros and cons of using this method are discussed as well as a comparison between the gauge and tube and barometer measurement techniques. Case studies showing the accuracy of shaft gauge and tube measurements are also presented.

Jan 1, 1991

By D. Constantinides

In 1981 a Zn-Ag-Pb deposit was discovered in the vicinity of Molai, Greece. Subsequently, it was determined to be of the Kuroko type. The geology of various areas in the southeast Peloponnesean Peninsula is similar to that of the Molai deposit. Since favorable geologic criteria are present, absent, or unknown in varying degrees in all areas, it was deemed necessary to classify and rank the prospective areas according to the level of information available. For each level of information, an ore discovery model based on pragmatic exploration criteria was developed, enabling the favorability of occurrence to be calculated for each area. A Monte Carlo simulation was used to calculate the probabilities, the input data consisting of quantitative and qualitative estimates of the geologic criteria for each area. Three levels of information were modeled : Level A consisted of 9 criteria, level B of 12 criteria, and level C of 20 criteria. The three levels of information were tested on the Molai area. The results exceeded expectations, showing the gen¬eral trends which control mineralization at the lowest level of information. With an increase in the level of information, geological trends become more evident and a differentiation can be made between areas containing Cu mineralization, exhibiting a low probability, and areas likely to contain Zn-Ag-Pb mineralization. The models were then applied to the neighboring areas - only level A and B were available.

Jan 1, 1986

By William G. Davenport, Eric H. Partelpoeg

Direct smelting of copper in a single vessel has long been the extractive metallurgist's dream. Such a process offers the important advantages of (i) maximum use of the energy available from oxidizing the sulphur and iron of the concentrate; (ii) restriction of SO2 emissions to a single constant-strength source; (iii) minimum materials handling and (iv) elimination of at least one process step. Extensive developmental work was carried out in the 1960's and 1970's to implement such single-step processes. Some of the processes reached the prototype stage and it appeared that copper smelting technology was on the threshold of a new, efficient, minimum-pollution era. Since that time, however, the forward thrust has slowed and single-step smelting is still a process of the future. The paper describes in detail the potential advantages of single-step smelting; its history and current status; and the reasons why it has not been adopted industrially. It concludes that the potential benefits of single-step smelting are powerful and that many of the difficulties encountered in the 1970's will be overcome in the 1980's.

Jan 1, 1985

By Walter Küng

The Henderson Coarse Ore Conveying System is a three flight belt conveyor system transporting primary crushed molybdenum ore 24 km (15 miles) underneath the North American Continental Divide. One of the conveyors is 16.8 km (55,200fi) in length with 8,200 kW (11,000 HP) of installed power. The overland conveyor contains 11 vertical curves and 9 horizontal curves, some with radii as small as 1,500 m. he system began full operation in December 1999 and is one of the longest and most complicated belt conveyor systems yet constructed. he design of this conveyor system utilized many innovative engineering concepts including low-energy belt covers, low-resistance idlers, torque-controlled tail drives, combined gravity and active winch take-up systems, small radius horizontal curves and belt turnovers. his paper reviews the start-up of the system, discusses the success of the design and addresses the lessons that can be learned from the first 4 years of operation of this unique conveyor system

Jan 1, 2004

By Yelloji M. K. Rao, P. Somasundaran

Reagents of biological origin are becoming more and more important in the field of metallurgy, especially in the areas of mineral processing and hydrometallurgy. The advantage of lower operating cost over physical and chemical processes and the capacity to operate with low grade ores make the microbial processes further attractive. In this paper, the role of microbes directly as a reagent and microbially produced reagents or secreted metabolites in mineral processing and hydrometallurgy will be discussed. Adhesion of microbes to surfaces is known to alter the hydrophobicity of minerals. Applications include surface modification to impart hydrophobicity or hydrophilicity on sulfide or non-sulfide minerals and dissolution of precious metals. Microbes can also perform the role of flocculating agents. Biosorption of toxic and heavy metal ions by microbes are finding application in treating tailing ponds. Mechanisms associated with the use for microbially produced reagents are discussed along with some recent results.

Jan 1, 1994

By Emily Dieckman, Claire Kincaid

"When most people think “miner,” they picture an older white man in a dusty shirt and suspenders. He’s holding a gas lamp and a pickaxe, peering at the walls of a dimly lit cavern. This image, while steeped in heritage, is no longer representative of what mining is: a global, increasingly diverse industry.It’s an industry made up of individuals like Zambian-born Chushi Mwewa, PE, president of Southlands Engineering, LLC in the United States and managing director of Southlands Engineering Limited in Zambia; Navajo tribe member Peter Denetclaw, manager of environmental programs and Navajo relations at Freeport-McMoRan; and Chinese and Jewish Alyssa Hom, a project engineer at McCarthy Building Companies.According to the Austrian Federal Ministry of Science, Research and Economics, 168 out of the world’s 195 recognized countries have some mining or mineral resources activity, and the mining industry directly employs more than 25 million people across the globe.However, according to McKinsey & Company’s 2017 “Women in the Workplace” study, white males hold 67 percent of C-Suite positions and 70 percent of senior vice president positions in the corporate world, and mining is no different. This uniformity among leadership has been tied to lower levels of employee engagement, innovation and business growth. The bottom line is this: Diversity is good for business. The question industry leaders must now ask themselves is not “Will we promote diversity?” but “How will we promote diversity efficiently and permanently?”More than 80 industry professionals, consultants and students gathered to discuss this question and share stories at the “Developing Diversity in Mining” workshop organized by the University of Arizona’s Lowell Institute for Mineral Resources (IMR), held during the 2017 SME Arizona Conference in December 2017.Brad Ross, co-director of the IMR and one of the facilitators of the workshop, said he felt diversity was important to discuss because he has witnessed its benefits throughout his career in the mining industry.“By creating a team of people with different experiences and perspectives, a company is better equipped to see the big picture and to creatively tackle problems,” he said. Speakers from industry and academia,including Mwewa, Denetclaw and Hom discussed the challenges surrounding achieving diversity and inclusion as well as the roles and responsibilities of different stakeholders."

Jan 2, 2018

By Pierre Ollivier, Dominique Morin, Pr. Ivo Toromanoff

Refractory gold ores have been processed by bio-hydrometallurgical process at B.R.G.M. (Bureau de Recherches Géologiques et Minières), Research Centre ,Orleans,France. The liberation of gold has been studied and the following steps for gold recovery improved. The overall process flowsheet has been established comprising different ways of treatment before the final discharge of the effluent. Iron and arsenic are successfully precipitated under well controlled Eh-pH conditions. Long term stability tests have been conducted and the research programme is to be continued with the crystallo graphic studies of the precipitates. Economical studies have been performed on the base of data obtained on parameters studies.

Jan 1, 1990

By M. K. Patel, K. C. Wade, M. Cross

In the past decade a good deal of effort has gone into the computer simulation of the heat distribution of pellet induration systems. The major uncertainty in the analysis of such systems is the gas flow distribution and, in particular, the role of leakage. Evaluation of the leakage into or out of a zone has proved to be very difficult, as has the cross-flow from one zone to another when adjoining zones have gas flows which change direction from up draft to down draft for example. This paper describes an initial model to calculate the gas flow distribution in a variety of practical situations of interest to those involved in pellet induration. The model is based upon a multiphase CFD code called CASCADE which is used in conjunction with the pellet induration simulation INDSYS.

Jan 1, 1990

By Nick Tessitore, Ryan Marsters, Alex Warren, Dylan Fawaz

The West Gates Deicing Industrial Waste Pond Expansion project at Denver International Airport seeks to expand utilities to accommodate additional terminal gates. The project includes six tunnel crossings beneath taxiways and runways with lengths ranging from 239 to 2,025 linear feet. Excavation methods include shielded tunnel boring machines and steerable auger boring. Designed initial support includes liner plate, steel ribs and lagging, steel casing, and Fiberglass Reinforced Pipe and ranges in size from 24" to 132". This paper will discuss challenges associated with the overall layout and design of the project, including contingencies to protect critical infrastructure. In addition, a construction update is provided.

Jun 23, 2024

By P. Massacci

This study deals with the development and utilization of computer models for evaluating the extent to which variability of raw material grades can be reduced from the deposit to the processing plant. The specific case of a cement works is examined. The deposit and the elementary quarring operations were modeled for the medium and long-term planning of production with the objective of predicting grade variability of the flow stream in time. The feeds inferred from previous modellings were used for simulating storage operations. In particular, the storage process (linear stockpile, as an alternative, blending from various heaps) was modelled in order to select the main parameters of the process to minimize grade variations of the feed to mill. The ways followed for modelling the prehomogenization process are described. The homogenization performance and efficiency in the silo stage has also been studied and an estimate made of the distribution of residence time on the basis of input and output sampling.

Jan 1, 1986

By Derek J. McCracken, William G. Holroyd

Emery is a rock that at one time held a large share of the abrasives market. The introduction of synthetic abrasives, however has forced it to settle for only certain niches in the marketplace. This loss of market share is due mainly to the higher amounts of impurities and weaker internal structure that naturally occurring minerals have compared to manmade materials. The use of rocks and minerals as abrasives dates back to early man, who used flint, quartz, and other natural materials to fabricate various tools. During the 19th century, with the Industrial Revolution imminent, the character of the abrasives industry was changed forever as synthetics were introduced. Frank B. Norton is credited with producing the first manmade abrasive when, in 1855, he manufactured a vitrified grinding wheel using emery grit and clay. Before Norton's accomplishment emery had been the only commercially available abrasive. The latter part of the 20th century has seen synthetics capture an increasing share of the abrasives market from natural materials. The term emery is believed to have been derived from the words emeri (French), smeriglio (Italian), and smiris (Greek). The term corundum, for the principal mineral of emery, seems to have originated from kauruntaka, the Indian name for the mineral. GEOLOGY Emery is a gray to black, granular rock comprised of various minerals including corundum (A1,0,), an iron-bearing mineral (usually magnetite-Fe,O,, hematite-Fe,O,, or hercynite- FeAI,O,), and several trace impurities such as mullite, titania, silica, and magnesia. The hardness of emery normally ranges between 7 and 9 on the Mohs scale, depending on its mineral com- position and level of impurities. Corundum, the hardest mineral in emery, typically has a hardness of 9. The specific gravity of emery ranges from 3.2 to 4.5, also depending on mineral composition and purity. The crystallography of each mineral contained in emery differs somewhat. Corundum exhibits an hexagonal crystal structure, whereas magnetite forms within the isometric system, frequently as octahedral crystals. Hercynite, an iron spinel, is also isometric. Hematite has an hexagonal structure but often is found as botryoidal and reniform masses. Principal deposits of commerical emery are found in the United States, Turkey, and Greece. In the United States two emery producers in the Westchester County-Peekskill area and one in the Cortlandt County area of New York closed their mines in the late 1980s. Commercial production in the United States now comes only from the western Cascade Range in Oregon. The emery in New York has a typical A1,0, content of 41.5%. Most of the rock is not true emery because it contains a mixture of spinel and magnetite but very little corundum. The deposits are of Late Ordovician-Early Silurian age and consist of veins in which emery is mixed with olivine, pyroxene, and hornblende. The veins evidently were formed by contact metamorphism and are surrounded by Precambrian schists that contain mica, sillimanite, cordierite, garnet, and quartz. The deposits in Oregon were formed during Miocene time by the contact metamorphism of ferrunginous bauxite by intrusive lamprophyric dikes and plugs. Emery is found in thin layers bordering these tabular dikes, which are usually oriented perpendicular to bedding, and in "surficial placer deposits. The emery deposits in Turkey occur as small, massive, lens- shaped bodies and as surficial placers. They are believed to have formed during Permian and Triassic times. In Greece the principal site of emery production is at Cape Emeri on the Island of Naxos. These deposits consist of lenticular masses of emery surrounded by marble. They originated during Mesozoic time, evidently by metasomatic replacement. Smaller deposits on several other Aegean islands were formed by the metamorphism of bauxite or other alumina-rich materials.

Jan 1, 1994

By R. Schipper

Two bench scale biochemical reactors (BCRs) were operated over a period of 3 months for the removal of uranium, radium, and selenium from mining influenced water (MIW). A BCR is an anaerobic reactor comprised of organic and inorganic substrate including woodchips, straw, sawdust, and limestone. Uranium and selenium are removed in a BCR by biological reduction of oxidized species (i.e., selenite, selenate) to less soluble forms (Pahler et al. 2007, Blumenstein et al. 2008, Rutkowski et al. 2013). It is believed that radium may be removed through absorption to the biomass in the BCR. The bench scale BCRs were constructed of 6 inch PVC columns with a top to bottom flow configuration. The bench influent water consisted of three different water ratios from two adit seeps. BCR hydraulic retention times of 24 to 36 hours were targeted during the study. Influent concentrations ranged from 19 ug/L to 1.86 mg/L for dissolved uranium, 12 ug/L to 270 ug/L for dissolved selenium, and 4.9 pCi/L to 24 pCi/L for radium 226. The average and maximum dissolved uranium removal was 93.6% and 98.5% respectively, the average and maximum dissolved selenium removal was 93.3% and 98.9% respectively, and the average and maximum radium 226 removal was 89.5% and 100% respectively.

Feb 23, 2014

By Janet E. Lamarre

Current statistics show that 90% of new-business failures are caused by the unsuitability of the entrepreneur for the business he has started. Are you a suitable candidate for success as a consulting geologist? Should you start your own geologic consulting business, and when? This paper investigates the demand for consultants with respect to general economic trends and mineral exploration activity trends. Furthermore, the study reveals certain technical skills and personal characteristics important to the success of the consulting geologist. Research shows chat certain expectations which prompted geologists to change careers are fulfilled while other unanticipated expectations often are also met.

Jan 1, 1985

By Hetland Donald L.

Regional Tertiary formations and basins of local sedimentation which contain uranium deposits west of the Rocky Mountains are mainly of Oligocene, Miocene, and Pliocene age (fig. 1). The host rocks have been derived mainly from intrusive and extrusive igneous rock. The major host formations which cover broad geographic areas include the Esmeralda, Truckee, Humboldt, Thousand Creeks, Payette, Panaca, Cedarville, Coso, and San Joaquin Formations. Local areas of Tertiary sedimentation containing uranium deposits occur near Yuma, Safford and Artillery Peak, Arizona; Dillon and Canyon Ferry, Montana; Spokane Indian Reservation and Pend Orielle River, Washington; Topaz Mountain, Utah; Stanley Basin, Idaho; and Sonora Pass, California. Uranium deposits in these sediments have been classified into five categories based on environment (fig. 2). They are: (1) Deposits in lake sediments consisting mainly of water-laid tuffs; (2) Deposits in lake sediments intruded by volcanic plugs; (3) Deposits in lake sediments interbedded with arkoses near batholiths; (4) Deposits in coarse volcanic sediments in local sedimentary basins; (5) Deposits in arkosic conglomerates in local sedimentary basins.

Jan 1, 1969

By Duluth Engineers' Club, Engineers' Club of Northern Minnesota

"During the last ten years great strides have been made, on the Mesabi Range, in the practice of beneficiating low grade iron ore material. By .beneficiation is meant all methods of removing impurities, and raising the iron content to a point where it can be sold in open market, the principal impurities being silica and moisture. The • general processes to which low grade iron ores are amenable are as follows:1. Thermal(a) Drying ; removes hydroscopic or atmospheric moisture. .(b) Calcining; removes carbon dioxide from iron carbonate, molecular water from hydrated hematites, and atmospheric moisture.Roasting; removes sulphur, carbon dioxide, molecular water and atmospheric moisture.Agglomeration; primarily for the purpose of preparing finely divided material for blast furnace; briquetting and sintering.2. MechanicalScreen sizing; removes rock and sand.Classification; removes sand by means of currents of water of varying velocities.Log washing; removes fine sand.Jigging; removes larger particles of impurities than is possible by log washing. Certain types of jigs remove fine sand.Reciprocating tables; recover fine iron particles from sand discarded by above processes.Magnetic separation; applicable to the commercial separation of the magnetic oxide of iron from gangue material. From a scientific standpoint it is possible to separate certain hematites and limonites from their gangue:(g) Miscellaneous processes; comprise dry concentration, electro-static separation and other processes."

Jan 1, 1920

By F. Lincoln & B. Rodier, G. Poniatowski, N. Kawashima, T. J. White, J. H. Kyle, G. F. Eaton

The history of Australia is a narrative of the discovery and development of its mineral wealth. The gold strike at Ballarat, Victoria, in 1851 transformed the colony by triggering the first great influx of migrants to Australia, and the development of subsequent mineral discoveries lead to a vast resource industry. However, beneficiation of base and precious metal ores carried with it an environmental penalty, not addressed until the last quarter of this century. In particular, the extensive deposits of gold, silver, lead, copper and zinc reside in sulphurous ores which often contain arsenic, antimony and mercury as significant contaminants that are released as unwanted by-products during smelting and refining. Until recently, these toxic concentrates were discharged to the atmosphere or receiving waters, collected in tailings ponds close to the smelters, or dumped at sea. Although such procedures . were acceptable in the past, more stringent environmental controls have required a re-examination of these practices and encouraged intensive efforts to develop enduring solutions to the disposal of these wastes. From this research has emerged a promising new generic technology called Xtaltite (pronounced crystal-tight). In this approach, geochemical principles are employed, first, to reduce the toxicity of heavy metals to low levels, and second, to identify and engineer suitable repositories for the permanent disposal of the consolidated waste form. In this paper, we emphasise the application of Xtaltite to the disposal of arsenious smelter fumes derived from gold winning. The principles ofXtaltite will be described and its technical and economic performance compared with conventional technolo­gies.

Jan 1, 1995

By E. Harrison

The Greens Creek Ore Bodies are located approximately 18 miles southwest of Juneau, Alaska in an area on Admiralty Island classified as a non-wilderness national monument. An area-wide stream sediment geochemistry program targeted the deposit in October of 1973. Today, after 37,000 meters of combined surface and underground diamond drilling, three ore zones are known to exist with total reserves approaching 4.1 million tonnes. Lying within moderately folded metasediments of an undetermined age, these orebodies are thought to be of seafloor exhalite orgin and contain unusual and impressive amounts of gold, silver, lead, zinc and copper.

Jan 1, 1986

By William Petruk

Performance assessments are carried out to monitor operations, to evaluate performance and to identify processing problems. The assessment involves collecting and analyzing representative samples from critical points in a flowsheet and interpreting the data. Sample analysis techniques include chemical analyses, mineralogical investigations, mineralogical analyses, and materials balancing. Chemical analyses provide the lowest cost assessment and should be used liberally, particularly in monitoring a process. Materials balances performed on chemical assays for a suite of samples are used as a first step in evaluating a process. Mineralogical investigations are more expensive than chemical analyses but need to be used only at the beginning of mining and metallurgical operations and as a second step in assessing processing problems. Quantitative mineralogical analyses combined with materials balancing provide the most complete performance assessment, but the procedure is expensive. On the other hand, the assessment has the potential of a large payback when carried out where warranted.

Jan 1, 1991

By T. I. Probert, B. W. Burdett, L. B. Hales

Selecting a mineral processing control system from the multitude of offerings can be a formidable task. To assist the plant designer, the material in this chapter includes the advantages and disadvantages of different equipment types, configurations, and control strategies. Selection procedures are detailed, and the importance of each step in the design and selection process is explained.

Jan 1, 1986

By Michael Day, Paul Kos, Scott Brinton

Quantitative hydrogeologic characterization of fractured rock is challenging because fracture systems are convoluted and difficult to characterize discretely. For large-scale water resource impact analyses, it may be more appropriate to use a watershed water balance approach and analyze fractured systems in terms of “bulk” hydraulic parameters over a large enough scale (hundreds of meters), so that the fractured media may be evaluated as “equivalent” porous media [1]. This is a common investigative methodology for mountain watersheds in fractured bedrock terrain because it does not rely on discrete flow paths but instead evaluates inputs to (recharge) and outputs from (discharge) the ground-water system [2,3]. This paper describes the use of this methodology to perform a practical and cost-effective hydrogeologic characterization and mining impact analysis for a proposed granite quarry in a mountain watershed. The key conclusions of the study guided the mine planning that was designed to minimize impacts to the fractured granite hydrogeologic system and preserve recharge to downgradient sedimentary aquifers.