Search Documents

By Kenneth Seaver

Discussion of the paper of KENNETH SEAVER, presented at the San Francisco meeting, September, 1915 and at the New York meeting, February, 1916, and printed in Bulletin No. 105, September, 1915, pp. 1913 to 1927. WILLIAM HUTTON BLAUVELT, Syracuse, N. Y.-I think that Professor Richards' statement regarding the reason for the failure of the Bethlehem ovens was due to a misconception on his part. Silica bricks were not used because the ovens were built under German design and management and it has not been the practice in Europe to use silica brick nor has it been necessary, on account of their lower heats and slower coking time as compared with the present American practice. J. W. RICHARDS, So. Bethlehem, Pa.-While acting as Chairman at the San Francisco meeting, in introducing this paper of Mr. Seaver, I made some remarks in discussion referring to unsuitable brick having been used in a coke plant at So. Bethlehem, Pa., and being the principal cause of the failure of these ovens. This statement having come to the attention of the Didier-March Co. of Perth Amboy, N. J., who furnished the firebrick used in the construction in the original ovens referred to, at the Lehigh Coke Works, near So. Bethlehem, Pa., their. manager, Geo. A. Balz has corresponded with me, and wishes to have placed on record a general denial of the statement referred to. As a matter of justice to the manufacturers of the firebrick, it is but right that their statement should be given as much publicity as my statement which has been objected to, and I take pleasure in placing upon record the statement of Mr. Balz, general manager for Didier-March Co., extracted from a letter to me dated Jan. 14, as follows: "The

Jan 5, 1916

By E. H. Kelton, R. D. Grissinger

In designing structural members of steel and some other materials the design engineer has available recognized values of elastic modulus and safe working stress that may be substituted in well-known engineering formulas to give him desired cross-sectional areas and deflections for a particular part. Zinc, on the other hand, has no generally recognized modulus. It flows under continuously applied loads. Therefore, the designer of structural members must use a range of working stresses depending on the continuous load and the amount of permissible distortion. The only method of obtaining these values is by creep testing. Creep testing of zinc has been carried on for some 20 years by this laboratory, covering a wide range of zinc and zinc alloys. Types of test included tension, compression, and simple and cantilever beams at temperatures ranging from o to I50°C. Specimen conditions ranged from as-cast or as-rolled to accelerated aged in steam or dry air. Effects of plating were investigated also. It is not the intention of this paper to expound all these factors but rather to present the final data on well-known zinc die-casting alloys and to suggest means of applying these data to engineering design. Early Work In the early work on creep testing of zinc, the direct-loading tension method was used. However, direct loading of die castings was unsatisfactory because of the high loads required. For instance, a standard die-cast tension bar having a cross-sectional area of about 0.049 sq. in. would require a direct load of about 1000 lb. for a unit stress of 20,000 lb. per sq. in. Also, tests were made at nominal room temperature, but normal variations caused fluctuations greater than those due to experimental error or other causes, so that control of this variable within ±1/2°C. seemed essential. These two factors led to the development of an apparatus described by J. Ruzicka,' in which the specimens were loaded by means of a lever and were held at constant temperature by means of an oil bath. While Ruzicka's apparatus yielded excellent check results, it seemed desirable to have some setup by which literally hundreds of die-cast specimens could be tested at the same time. This would permit the conducting of a number of low-load tests designed to run 10 years or longer and still leave capacity for current high-load work. Beam testing in a constant-temperature room was the answer. Test Method Preliminary work indicated that die-cast beams of various lengths and cross scctions yielded the same result within reasonable limits regardless of whether they were tested as simple beams, uniformly loaded beams, or cantilevers. Accordingly, the simplest type was adopted. This was a,

Jan 1, 1945

By J. O. Scott

Transient pressure behavior of wells intersected by a single vertical fracture has been examined by means of a heat pow analogy. Results are correlated in terms of dimensionless pressure change and dimensionless transient time. The resulting curves are found to lie between the dimensionless curves for a cylindrical well and a line source when effective well radius is expressed as one-fourth of the total fracture length. Results are also shown for various degrees of afterflow. Use of the curves provides a means of determining reservoir permeability, wellbore radius, and thereby fracture length, even when the final slope of the transient curve is not obtained. Superposition of curves may be used to confirm existence of vertical fractures in the reservoir adjacent to the well or to indicate a damaged zone on the fracture face. INTRODUCTION Hydraulic fracturing has become a standard well completion practice for the purpose of increasing flow. Results are normally gauged in terms of some sort of "stabilized" flow rate established before and after the treatment. This procedure may be misleading because pressures in or around the well do not become "stabilized" during the test period. Transient pressure tests on fractured wells can overcome the objections to stabilized flow tests by indicating when a stable pressure gradient is reached. In addition, the transient pressure tests can be used to determine formation flow capacity and effective wellbore radius. The effective wellbore radius may be used as a measure of the success of the fracturing operation. The slope and position of the transient pressure-log time curve may be used to determine the flow capacity and wellbore size after sufficient lapse of time so that the pressure gradient in the vicinity of the fractures becomes constant. However, in tight reservoirs or in short tests this condition may not be reached. Presence of the fractures in tight reservoirs may cause a constantly increasing slope to the transient pressure curve. If this slope is picked too soon, formation flow capacity will appear high and the fracture size will appear too small. This paper is intended to clarify the early transient behavior of vertically fractured wells. It shows how formation flow capacity and wellbore size can be determined even though the maximum slope of the transient pressure curve is not obtained during the test. Development of the techniques of transient pressure analysis for wells has been summarized by Perrine.' He reviews the various definitions of wellbore effects such as skin effect, productivity ratio, damage factor and condition ratio. In the present paper, use of these terms is avoided by defining an effective wellbore size. For the fractured well this effective wellbore size is larger than the actual wellbore. Assumptions made are constant flow rate at the well, constant fluid compressibility, constant fluid mobility and uniform porosity and formation thickness. From the basic differential equations of flow, two different solutions may be obtained. The first, the line source solution, is commonly used in transient pressure analysis.' It expresses the change in pressure at any radius due to withdrawal or injection of fluid at the line source from an infinite reservoir at uniform initial pressure. This equation, in oil field units: is

By J. C. Smock

The magnetic iron ores of New Jersey are found in the northern part of the State, in the Highland Mountain range, which runs from the New York line on the northeast, to the Delaware River, near Easton, at the southwest. The same range continues across Orange County to the Hudson River, and towards the southwest it is known in Pennsylvania as the South Mountain. It is more properly an elevated table-land, quite deeply furrowed by several narrow, longitudinal valleys, and shorter cross-valleys or gaps. The ridges or lines of elevation, as well as the lower valleys, conform in their general direction very closely to the general trend of the whole belt or table-land, that is, from northeast to southwest. This also agrees with the prevailing strike of the rocks. This great uniformity in the altitudes of the hills and ridges, and the direction of the lines of depression corresponding to the strike of the strata, point to an original table-land, which, through the long action of denuding agents, has been quite deeply eroded, giving rise to the present surface configuration, so that some of the former and uniform features have been partially obliterated. The very few cross-valleys or depressions are much more irregular in their course, and serve as outlets through which the drainage is carried either into the Kittatinny Valley on the northwest, or to the broad, red shale and sandstone plane bounding the highlands on the southeast. The area of this highland

By L. A. Rapoport

This paper is intended as an aid in the perfornzance and interpretation of experimental studies of multi-phase flow in porous tnedia. The mathenmatical formulation of incompressible, two-phase flow phenomena in a three-dimensional porous medium is presented. The resulting equations which account for the effects of gravitational and capillary forces are used to derive general scaling laws permitting accurate representation of water-oil displacement processes by means of experimental flow models. The significance of the scaling laws is examined in the light of the physical concepts of micro-behavior of fluids in porous media. Formulations of scaling con(litions obtained by application of dimensional analysis are reviewed. The principles of application and the limitations of flow model studies are discussed. INTRODUCTION Most of the problems facing a reservoir engineer involve three-dimensional, two-phase flow systems. influenced by the effects of gravitational and capillary forces. Present computational procedures generally do not permit the evaluation of such systems without introducing greatly simplifying assumptions. The actual reservoir configuration is usually replaced by one or a combination of several "equivalent" linear systems, and the effects of capillarity and gravity are considered to be negligible. While these assumptions may in many instances be justified, there are a number of important practical problems for which the results obtained on the basis of such simplifications remain open to question. An alternate approach to the problems that are not amenable to analytical treatment consists of seeking their solution by experimental laboratory investigations. The main difficulty of such investigations lies in the fact that multiphase flow phenomena subjected to gravity and capillary forces proceed differently at different rates and in systems of different dimensions. Therefore, unless great discrimination is exercised in selecting the conditions and interpreting the results of laboratory tests, such tests may be entirely misleading in regard to field applications. The purpose of this paper is to present a theoretical background for the performance of laboratory tests that are more nearly representative of field behavior. It will be shown that simulation of field behavior can be achieved by conducting laboratory tests under conditions selected in accordance with definite scaling laws. The formulation of conditions required for the scaling of two-phase flow experiments in porous media has been presented in the literature on several occasions.12,3,4 One of these formulations advanced by Leverett1, cannot be considered applicable to most practical cases inasmuch as it does not cover generally the regime of laminar flow. An adequate treatment, based on the consideration of dimensional analysis, was presented by Engelberts and Klinkenberg.2 Their treatment, however, is concerned primarily with the scaling of linear flow systems, and hence somewhat limited in scope. Accordingly, the formulation of more general scaling laws, applicable to three-dimensional systems, appeared to be warranted. It appeared, furthermore. desirable to establish this formulation on the basis of a mathematical treatment, rather than by application of general principles of dimensional analysis, to permit more explicit

Jan 1, 1956

IT is not enough to know how to melt well and to have the bellows and charcoal for your purpose. If you wish to make small castings turn out well, on account of their thinness, it is necessary to aid the metals with unctuous and corrupting materials like tin, sublimate, arsenic, or realgar,

Jan 1, 1942

By Arthur Phillips

THE progress made in recent years in the art of dispersion-hardening has naturally led to an intensive study of alloy systems capable of yield-ing supersaturated solid solutions at ordinary temperatures. In general, the investigations have been confined to rather precise determinations of solubility limits and to experimental approaches designed to furnish more complete information regarding the rate and nature of precipitation under appropriate thermal conditions. Efforts are being made to focus more sharply on the atomic changes that are a direct consequence of the instability of the supersaturated solution. Here precision X-ray methods have come to be of considerable importance because lattice parameter measurements indicate very precisely the concentration of solute atoms in the solvent lattice. In spite of the general acceptance of parameter values as a criterion for the placing of solubility limits, it may be suggested that no thorough appraisal has been made of the several factors that conceivably may affect such measurements. More specifically, little attention has been devoted to the significance of surface energy conditions, specimen size and method of preparation, with par-ticular regard to the genesis of the grains and the surface concentration changes as a consequence of heat treatment and etching. Stenzel and Weerts1 recently published the results of a detailed study of precipitation reactions in aluminum-rich copper alloys. They found that, although copper lowers the lattice constant of aluminum, a 5 per cent copper alloy quenched from 150° and 225° C. had parameter values unquestionably higher than that of pure aluminum. Their results seem to substantiate, at least qualitatively, the earlier work of von Göler

Jan 1, 1934

By R. W. Fountain, W. D. Forgeng, G. M. Faulring

Precipitation of the phase Co3Ti (Cu3Au type) from a Co-5 pct Ti a11oy has been investigated using single-crystal X-ray diffraction techniques. Oscillation and transmission Laue patterns of specimens aged for short-time periods at 600" C indicate the formation of titanium-rich and titanium-poor zones coherent with the {100} matrix planes. Longer aging times at 600° C establish that the equilibrium phase also forms on the {100} matrix planes as platelets. These observations are corroborated by electron metallography; electron diffraction studies show the phase Co3Ti to be ordered. A probable sequence of the precipitation reaction is discussed. A previous publication by two of the present authors reported on the phase relations and precipitation in Co-Ti alloys containing up to 30 pct Ti.1 The results of this investigation established the existence of a new face-centered cubic inter metallic phase, ranging in composition from about 17.0 to 21.7 pct Ti at temperatures below 1000° C The decomposition of the fcc supersaturated solid solution was studied employing hardness and electrical resistivity measurements. The changes in hardness upon precipitation in alloys containing 3, 6, and 9 pct* Ti were found to be associated with an initial increase in hardness followed by a plateau and then a second, more pronounced hardness increase. Investigation of this behavior by electrical resistivity measurements suggested that two different kinetic processes were involved, which, when interpreted in terms of the kinetic relation,2-4 indicated that initial precipitation was in the form of thin plates. On continued aging, the plates impinged during the growth process. The general features of these findings have been confirmed by Bibring and Manenc,5 while, in addition, they report the phase to be ordered. The present investigation was undertaken to provide more definite information on the structural relationships between the precipitate and the matrix. EXPERIMENTAL PROCEDURE Single crystals of a (20-5 pct Ti alloy were prepared from the melt employing the Bridgman technique. Poly crystalline rod, 1/2 in. in diam, prepared from vacuum-melted material, was machined to 3/8- in. diam to remove any surface contamination that may have resulted from hot-working. The crystals were grown under a purified hydrogen atmosphere in high-purity alumina crucibles heated by induction. Considerable difficulty was encountered in attempting to grow monocrystals because of the high melting point of the alloy and the high solute concentration. However, one crystal about 6 in. long was obtained which was essentially a single crystal except for one or two very small grains around the periphery. The as-grown crystal was solution heat-treated for 24 hr at 1200°Cin a purified argon atmosphere and water-quenched. One-quarter-in. slices were taken from each end of the solution heat-treated crystal for chemical analyses, and the remainder of the crystal was mounted and oriented by the back reflection Laue Method. The chemical analysis of the crystal was as follows: Pct Ti Pct 0 Pct C Pct N Pct H Pet CO 5.29 0.08 0.004 0.002 0.0003 Balance By proper tilting of the crystal, it was possible to obtain slices 1/32 in. thick of [loo] and [110] orientation. The solution heat-treated crystal slices were sealed in silica capsules for the aging treatments, with titanium sponge placed at one end of the capsule to act as a getter. All slices were water-quenched from the aging temperatures, the capsules being broken under the water to ensure a rapid quench. Thinning of the slices for transmission X-ray studies was accomplished by a combination of mechanical and electrolytic techniques, the final thickness being about 0.1 mm. Laue patterns of the solution heat-treated crystal indicated that no strain was introduced by the thinning technique. ELECTRON METALLOGRAPHY After X-ray examination, the structural changes attending the precipitation were followed by examination of direct carbon replicas of polished and etched surfaces of the single-crystal slices and extracted phases. The earliest indication of significant structural change was observed after aging at 600°C The structure of a heavily etched, solution-treated crystal is shown in Fig. l(a). Aside from the etch pit pattern, no regularity of background structure is observed. On the other hand, in the background of the specimen heated for 500 hr at 600°C, the etching pattern shows a directionality indicating the influence of minute precipitate particles, Fig. l(b). On electrolytic dissolution of this specimen in 10 pct HC1 in alcohol, a large volume of very small, flattened cubes

Jan 1, 1962

By R. DiBella, H. Biloni, G. F. Bolling

A study of the detailed relationship between solidification substructure and microsegregation in dilute tin alloys has been continued. New observations reveal that depressions form at the solid-liquid interface not only as an initial form of segregation but throughout the range of increasing constitutional supercooling. In order to show the importance of this node formation it proves convenient to make two simplifications. Although substructure changes continuously as constitutional- supercooling increases,&apos; the following discrete stages may be used for discussion: 1) the planar solid-liquid interface; 2) ordered nodes, or depressions at the interface;&apos; 3) two-dimensional or elongated cells;3 4) regular or hexagonal cells;4 5) distorted cells, or hexagonal cells with branches;4 6) dendrites. It is also convenient to ignore observations made near grain boundaries which interact with the cellular substructure.2-4 And, it should be clearly pointed out that all singular depressions at the solid-liquid interface will be called nodes. Heretofore, the term "node" has been used without clear justification to describe both the truly isolated depression and the junction of cell walls appearing in a later stage of segregation. This usage is continued because it seems proved by the observations. Standard systematic growth of tin crystals was undertaken over a broad range of constitutional supercooling using various added solutes. Except for one or two chance observations, this research failed to reveal any appreciable range of growth conditions over which a disordered array of isolated nodes exists. Even though &apos;some finite range of random instability must exist, it is now concluded that stage one passes very rapidly to stage two. Next, after confirming that stage two passes to stage three by the elongation of isolated nodes: a reexamina-tion of stages three, four, and five followed. Standard metallography showed that pockets of higher solute concentration (for ko < 1) became more numerous in cell walls the more severe the growth conditions. These high-concentration regions must arise from depressions; however, in stage three their segregation is not distinguishable from the segregation of the nodes which join cell walls together. It seems, therefore, that the presence of nodes is causal in the formation of new cell walls, and that the mechanism by which stage three passes to stage four is initiated by nodes. If a similar reasoning is followed, the separation of stage four from stage five appears to be just a convenience that has arisen from the decanted interface observations made in the past. The present observations again show that more severe growth conditions relate directly to an increase in the number of nodes in the hexagonal cell walls. These nodes apparently serve as the origin for lines of segregation extending within the body of a cell, and can thus be assumed to represent the earliest form of branching,* as shown here in Fig. 1. The examination of stage six involved decanted-interface structures as in Fig. 2, which are similar to those considered by Rutter and Chalmers,5 Plaskett and winegard,6 and Hellawell and Herbert,7 and where distinct protrusions are each surrounded by a depressed boundary. The corresponding microsegregation behind the interface, but not far enough behind to allow a smearing of the segregation because of diffusion,4 is shown in Fig. 3. Both the shape of the decanted interface and the segregation pattern behind it

Jan 1, 1968

By C. E. Corson

The experiments of which the results and significance are set forth in this paper do not by any means cover the whole subject of the heat-treatment of the material referred to, yet they constitute a contribution to that general subject, rather than to the special department of&apos; annealing. The material here considered is acid open-hearth steel, containing from 0.50 to 0.80 per cent. of carbon, with a nearly uniform percentage of other elements. This class of steel is rapidly increasing in commercial importance. It is even rumored that the rail-specifications of some railroads will hereafter require open-hearth steel. Yet this particular grade seems to

Jan 1, 1907

By William P. Blake

Travelers in the desert regions of the southwestern portion of United States, especially along the valley of the Colorado of the West, can hardly fail to note that most of the rocky outcrope of the harder rocks have a uniform prevailing blackness of the surface, in strong contrast with the normal color of the interior of the rock when freshly broken. For example, the granitic or gneissic rocks of Pilot Knob, below Yuma, are blackened beyond easy recognition. So also rocks upon the lower Mojave in California are so thoroughly blackened, as if painted, that ordinary gneiss can scarcely be recognized without breaking it so as to show the interior color and structure. The discoloration is not confined to the rocky outcrops in place, but is found upon boulders and upon the loose rounded pebbles which strew the surface of the mesas along the Colorado river. These fragmentary rocks partake of the general blackening.

Jan 1, 1905

By E. B. Snyder, H. M. Kraner

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user&apos;s point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By H. M. Kraner, E. B. Snyder

This paper shows that volume stability, low porosity and decreased pyroplasticity are desirable for blast-furnace linings, partitularly for the hearth. It shows further that a hot load test is a valuable means of testing the fusion or softening behavior of a refractory at operating temperatures. The effect of carbon monoxide on commercia1 blast-furnace refractories in their as-received condition and after refiring is reported, showing that many commercial blast-furnace refractories disintegrate badly but that refiring decreases the effect and certain special refractories are now available which are almost free of the tendency. Factors Affecting Choice of ._ Refractories If one were to depend entirely upon experience or trial in the selection of clay refractories, the solution of a problem would be a slow process. Furnace campaigns are so long and attended by so many variables that it is difficult to draw fine distinctions within a reasonable period of time in regard to the quality of refractories used. It could be said, of course, that if service results do not yield the proper information for intelligent choice, there is no difference in the quality of brick being considered, but this is not necessarily true. Conventional ceramic tests are designed to give the ceramic engineer information as to the refractoriness and firing tempera- . ture, which he in turn internrets in terms of volume stability, ability to withstand load at high temperature (pyroplasticity), permeability, chemical stability and re-. sistance to the action of slag. In most refractory applications . several of these factors are involved. In a particular instance, one requirement may be predominant, while in others some other factors may be of primary importance. In this country, clay refractories are generally made from mixtures of plastic and flint fire clays. The process of firing a clay refractory is one of slowly melting the constituents, and during this operation its porosity is gradually reduced. The process is arrested, of course, in its incipient Stages and the Progress is determined by measuring slight changes in porosity, volume, bulk gravity, etc., that have taken place. Often the temperatures to which clay refractories are exposed in service are higher than those employed in their firing. However, if the manufacturer were to fire them at such high temperatures the brick would distort. Therefore it would be difficult for the manufacturer to fire all of his clay refractories to temperatures at which they are to be used, although in many cases it would be desirable from the user&apos;s point of view if he would do so. The porosity of clay refractories decreases by firing, to a minimum limit, after which a further increase in the temperature causes expansion in certain clay constituents and bloating in others. Both may occur in the same refractory containing two such clays.

Jan 1, 1944

By H. Herman, M. E. Fine

Kinetics of reversion and reformation of GP I were studied resistometrically in Al-1.7 at. pct Cu. The reversion process is over in roughly 1/2 minute at 205 "C irrespective of the amount of primary aging. After reversion the occurrence of an incubation time before reaging begins has been substantiated. The reaging kinetics is drastically accelerated by plastic deformation to the specimen. An incubation time is observed only if the specimen is aged before reversion. The incubation time and the effect of plastic deformation indicate that nucleation of GP I is heterogeneous. Simple clusters of copper atoms apparently do not act as nuclei for GP I. AFTER quenching aluminum-rich copper from the solid solution range, Guinier-Preston zones of the first kind, GP I, form very rapidly at room temperature. The rate, largely controlled by the concentration of vacancies, is initially most rapid1 (that is, at the time of the first measurement: 1/2 min) and decreases with time. The nucleation is thought to be athermal. If after aging for several days the GP I is dissolved by reversion at 205°C, according to measurement of Young&apos;s modulus an incubation period is observed before GP I begins to form on subsequent aging.2 Yet if the reversion is carried out immediately after quenching, both resistivity3 and modulus changes2 show no incubation effect. The zones which form after reversion have the same structure as those which form after the quench.4 Because of entropy considerations and also the short diffusion time, the solid solution after reversion, 2 min at 205°C, is probably more highly clustered than at the original solution treating temperature, 520" to 550°C. It appears most reasonable to associate with nucleation the incubation time observed on reaging after reversion. A simple cluster of copper atoms, many of which are presumed to be present after reversion, is then not a sufficient nucleus for GP I; a GP I nucleus must contain something in addition to a cluster of copper atoms. The purpose of the present note is to give some additional experimental information concerning the incubation time and rates of reaging after reversion. The existence of the incubation time has been verified by measurement of another property, the electrical resistivity. Acceleration of reaging after reversion by plastic deformation has also been investigated. In acl.dition, the kinetics of the reversion process itself was studied. EXPERIMENTAL Electrical resistance was measured by the poten-tiometric four probe method. The 1.7 at. pct Cu alloy was furnished by the Aluminum Co. of America in the form of 1/2 in. rod. The major impurities reported by Alcoa were Fe (0.002 wt pct), Si (0.003 wt pct), and Mg (0.001 wt pct). Specimens for measuremenl of resistance were prepared by rolling to 0.010 in., cutting 2 by 0.2 in. pieces, rolling the middle pclrtions of these to 0.005 in., and splitting the 0.010 in. sections up to the reduced central section to form current and potential leads. Aluminum extension wires insulated with ceramic tubes were spot welded to the leads. The specimen was supported by the lead wires. The whole specimen assembly was annealed at 500" C in an air furnace for more than 12 hr and then aged at room temperature. This was done to assure quick and complete resolution during subsequent solution treatments. These were carried out in Houghton&apos;s "430 Temper Salt" at 520&apos;C for 1 hr. Unless otherwise specified, quenching was accomplished by quickly transferring the specimen from a salt pot to 25°C water. Aging was carried out in a 3 liter dewar of distilled water, rotated and stirred. The temperature was controlled to +0.01°C with a thermomercurial regulator in conjunction with a transistorized relay

Jan 1, 1962

By Guilliaem Aertsen

The derivation of the word tire (or tyre, as it is spelled in England) is obscure. Some dictionaries suggest that it is the aphetic form for "attire, covering," so called as being the outside covering or band of a wheel; also as a corruption of "tier," the band which holds, or "ties," the rest of the wheel together. One dictionary states: "The supposed derivation of the word is that bands were first used on wheels in the City of Tyre, Syria." In the infancy of railroads, the tracks consisted of flat bars of iron, spiked or bolted to the upper surfaces of longitudinal timbers, which, in turn, rested upon masonry foundations. Stone blocks installed for this purpose on the old Germantown & Norristown Railroad, now the Chestnut Hill branch of the Philadelphia & Reading Railway, were to be seen for many years on the right-of-way, north of what is now Wayne Junction, Philadelphia, Pa. The "cornerstone" of the Baltimore & Ohio Railroad was laid Apr. 4, 1828, and the fist locomotive in America was built by Peter Cooper at the St. Clair Works, Baltimore, Md., in 1829 "to demonstrate its adaptability to a curved road." It is believed that the first successful locomotive was built in Philadelphia by Tyler & Baldwin in 1832 for the Germantown & Norristown Railroad. Rufus Tyler and Matthias Baldwin were brothers-in-law; the latter&apos;s name will be identified with American locomotives until locomotives are forgotten. The wheels on these first locomotives, designed to run on this primitive rail, mere shod with plain iron bands, bent and welded. The flanges consisted of separate iron bands, bent sidewise,welded, and bolted to the sides of the wooden fellies, or rims. Before many years had elapsed the tires were fabricated of iron bands, rolled in one piece with the flange projection on the side. The tire for each wheel was bent and welded and subsequently attached to the wheel center by shrinkage, bolts, rivets and various mechanical devices. Germany is generally given the credit for first making such tires of

Jan 1, 1917

By C. M. Schwartz, A. P. Young

ZIRCONIUM is noticeably embrittled at room temperature by hydride precipitate not only in notch-impact tests but also in tensile-impact tests.&apos; The embrittlement in slow-strain tensile samples is much less severe. To understand better the relationship of the hydride precipitate to the strain-rate effect in tensile samples, the surfaces of chemically polished zirconium tensile samples strained at a slow rate (0.03 in. per min head speed) and at an impact rate (18.1 fps hammer speed) were examined in the light and electron microscopes. Vacuum-degassed samples and hydrogenated samples (100 ppm hydrogen) were examined. The hydrogenated samples were slow cooled from 800°C. The most apparent difference between slow-strain and impact tensile samples was the preponderance of twinning over slip in impact samples as opposed to relatively little twinning in slow-strain samples. The twin bands in hydrogenated samples often terminated on hydride needles as seen in Fig. 1. Almost opposite the twin terminus is a fine crack and a nearly round fissure. Holes near the areas where single lens-shaped twins or opposing pairs terminate on hydride particles also could be seen In the light micrbscope. Quite frequently, microcracks associated with a partial row of hydride particles were visible, as in Fig. 2, indicating that the crack was parallel to a row of hydride particles. Some samples were chemically polished after straining to remove metal with a minimum of disturbance of internal voids. Fig. 3 shows a crack in the interior of a hydrogenated impact sample. Holes along grain boundaries were seen after impact in both degassed and hydrogenated samples. Very few microcracks were seen in degassed samples after impact or slow strain, or in hydrogenated samples after slow strain.

Jan 1, 1959

By B. G. Zambre, G. A. Parks, J. N. Roco

Automatic controls have long been a fact of technological life. Some understanding of control systems is rapidly becoming essential to the competence of mineral engineers. Students in undergraduate mineral engineering curricula, however, should not be expected to develop proficiency in the design and interpretation of control systems. They should be provided the opportunity to absorb some of the fundamental concepts and cant of such highly specialized peripheral fields as automatic controls. The present paper describes the components of a simple, flexible and relatively inexpensive control system designed primarily for the use of students in independent study projects. The control system is based on a continuous on-stream optical analyzer analogous to commercially available systems using X-Ray fluorescence analysis. The components can be easily adapted to control other separators and separations. As described here, they have been arranged to control the magnetic separation of a magnetite bearing specular hematite from quartz to produce a quartz product of fixed hematite content using a minimum of power. The control system consists of the magnetic separator* with a vibrating feeder, † a sampler, an optical scanner, a differential amplifier, a millivolt recorder ‡ and a motor driven, metered variable DC power supply for the separator electromagnet. An optional magnet current recorder is useful. The system as arranged for closed loop control is illustrated in Fig. 1. The elements of the loop are identified in automatic control jargon in Table I. The same components can be easily adapted for use in other control modes.§.1 * A Carpco Induced Roll High Intensity Magnetic Separator (Carpco Manufacturing, Inc., Jacksonville, Fla.); modified for external magnet power supply. A Jeffrey-Traylor Vibrating Feeder Type 1B (Jeffrey Manufacturing Co., Columbus, 0.). A Beckman Laboratory Potentiometric Recorder (Beckman Instruments, Inc., 619-A) fitted with adjustable limit switches for external circuit control (Beckman Instruments, Inc.. 71980). Terminology is taken from ref. 1. CLOSED LOOP OPERATION The separation is monitored through the optical reflectivity of the tailings stream which is proportional to the hematite content, THA. The difference, A, between the measured analysis (actually a proportional voltage) and a reference analysis (also a proportional voltage) is continuously recorded. The separation is controlled through changes in the electromagnet current, I, supplied from a motor driven variable source. The two primary variables, ? and I, are linked through adjustable limit switches on the

Jan 1, 1965

By Harry Seltz

INTERMETALLIC compounds are formed in many binary metal systems. Some compounds are stable to their melting points, and others decompose at lower transition temperatures. Even those of the first class are dis-sociated in the liquid state, as indicated by the continuous for in of their solubility curves at their melting points1. While the lattice structures of some of these compounds have been determined, their thermodynamic properties have not been investigated. In this paper is described the determination of the free energy and heat of formation of the compound CdSb, which is of the first class mentioned above, melting congruently at 455° C. This compound shows a rhombic structure, and the lengths of the edges of the elementary cell containing four molecules are: a =6.52, b = 8.60, c = 4.16 A.2 There are three possible methods of determining the free energy of formation of a compound of this type. The first method, applying the third law of thermodynamics, requires the measurement of its heat capacity preferably to liquid hydrogen temperatures, and a calorimetric determination of its heat of formation. The second method involves the study of the equilibrium of the compound in some gas reaction, such as: CdSb + CO2 = CdO + CO + Sb From the known free energies of formation of CdO, CO2 and CO the free energy of formation of CdSb could be calculated. The third method measures the electromotive force of a galvanic cell in which the cell

Jan 1, 1935

By Ernest Kirkendall

The amount of research done in the last fen years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Deschl in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl&apos;s paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for it? review and bibliography is an article by 14. I. Krynitsky.~ While considerable material lias appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined :it three temperatures. Procedure The method used consisted of plating copper on a beta brass, heating it, to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the tem perature at which diffusion takes place the beta brass is saturated wit11 copper. Thus, while the beta brass supplies thc zinc, no diffusion takes

Jan 1, 1939

By Ernest Kirkendall

The amount of research done in the last fen years on the subject of diffusion in solid metals is significant of the importance of this problem. To review the literature dealing with diffusion is unnecessary here. Deschl in 1912 reviewed the work that had been done on diffusion in solids and gave a bibliography of the literature published before that time. Mehl&apos;s paper in 19362 is an excellent review of diffusion in metals and contains a large bibliography. Of importance also for it? review and bibliography is an article by 14. I. Krynitsky.~ While considerable material lias appeared in the literature on diffusion in brass, the amount of information is not great compared to that pertaining to some of the other alloys. Most of the information published is of a qualitative nature; that which is quantitative varies considerably. Thus the quantitative determination of the rates of diffusion of copper and zinc in alpha brass by a new method appeared worth while. In the present investigation the rate of diffusion of zinc in approximately the same composition alpha brass has been determined :it three temperatures. Procedure The method used consisted of plating copper on a beta brass, heating it, to allow diffusion to take place, and measuring the concentration of copper by determining the lattice constant of the alloy. This method is unique in that it uses a beta brass of such a composition that at the tem perature at which diffusion takes place the beta brass is saturated wit11 copper. Thus, while the beta brass supplies thc zinc, no diffusion takes

Jan 1, 1939