Search Documents

An experienced drill operator is able to make a log of a drill hole defining physical properties of the earth such as hardness or structure as they vary with depth. This log is based on intuition or how the drill æfeelsÆ. Rock characterisation using measure while drilling (MWD) parameters aims at refining this intuition into a package that accurately defines the properties of the subsurface as the drill bit propagates. Subsurface investigation using MWD parameters aims to combine physical drill parameters: Pull down force, rotary speed, penetration rate, torque and vibration in such a way to yield real time rock properties. MWD is investigation in its most primitive form, put simply MWD is merely a physical probe æfeelingÆ what the rock mass is at depth.

Jan 1, 2001

By U JSger

The Westerschelde tunnel will be the first permanent road link between the Dutch regions of South Beveland and South Flanders. Two tunnel tubes, each 6.6 km long, will be driven using the shield tunnelling method. The difficult ground conditions and a water pressure of up to 6.5 bar make great demands on the design. This paper describes the problems and their solutions.

Jan 1, 1999

By S Rice, A Midlin

Many of the stacking and reclaiming machines employed in the mining industry today are operating in ways that were never envisaged in the days before they were commissioned, with greater throughput, increased annualised operating hours and load cycles well in excess of their original specification requirements being the norm. In many cases these machines were supplied prior to the widespread use of finite element modelling or, in the era when such software became commercially available, those supplied designed using simplified and/or coarser meshes than would be employed today. With many of these machines being expected to operate for many years to come, it is important that their ongoing reliability be maintained and their operational limits understood. In this paper, a case study is used to outline the method required for estimating the fatigue life already consumed and the likely real life left in a machine. By reference to the machineÆs prior operating history, the use of strain gauges in the field and the development of finely meshed finite element analysis (FEA), a coherent picture of the machineÆs operational state can be generated and then investment/maintenance decisions made to ensure continuity of machine operation.

Jan 1, 2007

CONTENTSSummaryIntroductionGeographical and Geological Outline of the RegionGrowth of the Mining IndustryTable 1: Production StatisticsGeneral GeologyRecent Alluvium and River GravelsSambeto SeriesMudstone and Basalt ContactVatukoula SeriesIntrusivesStructureGeologic HistoryLodesTable 2: Principal Lodes and Their OrebodiesMineral Assemblage and ParagenesisOre Shoots and Their ControlEmperor MineLoloma MineDolphin MineExplorationConclusionAcknowledgmentReferencesSUMMARYThe Tavua Goldfield was found in 1932 within a basin, both topographical and structural, near the sea on the north side of Viti Levu, Fiji, and has produced over £13,000,000 (Fijian) worth of gold and silver from the three mines...

Jan 1, 1953

By J-S Zhang

In this paper, the author briefly introduces the resource characteristics of Chinese iron ore, as well as the present increasing market demand for iron concentrate. The SHP-3200 wet high-intensity magnetic separator (HIMS) is used to separate complicated weak-magnetic iron ores being composed of specularite, limonite and siderite in Jiuquan Iron and Steel (Group) Co Ltd. Some technologies have been used to improve SHP-3200 HIMS, including modifying the angle of magnetic polar from 90¦ to 83¦, cooling the exciting coils by oil instead of air, adding reverse-washing equipment to wash off magnetic particles and adjusting the tooth-space of the matrix from 5.0 mm to 3.5 mm or 2.5 mm to enhance the recovery of fine particles. It is still difficult to meet the requirement for recovering more difficultly separated iron and the demands for high-grade concentrate of iron. In order to improve the recovery of difficult-separated iron, the film-magnetic separation technique is applied into the HIMS and a new LY matrix is designed to form magnetic gradient vertically. A flowing-film feeder is also added and the feed mouth is modified to make a slurry flow formed in the form of film along the wall of matrix. The microstructure and dissemination character of the mineral particles is studied, and the specific susceptibility of the primary minerals is measured. Then the distributive characteristics of a magnetic field for the separator with film-magnetic technique and the motion of particles in the process of separation are all analysed. By introducing the film-magnetic separation technique to SHP-Φ700 HIMS, the recovery of iron can be raised from 69.45 per cent to 76.07 - 78.96 per cent with the similar grade of concentrates of iron. Such an increase of 9.51 per cent in the recovery also shows that it is feasible for such film-magnetic separation technique to be applied into HIMS.

Jan 1, 2005

For several decades miners have been obliged to maintain a vast supply of sharp steels at the working face to meet the hungry needs of rock-drills. In medium and large size mines this has meant the setting up of an organisation to store steels, to make and sharpen bits with all the complication and skill of forging, hot milling and heat treatment, and to transport sharp and dulled steels to and from the working face with all its labour, wastage, and inconvenience to other mining operations.In a mine with 250 rock-drills in use, a flow of more than 60,000 sharpened steels each month has to be maintained to keep the machines fully employed, so some idea of the magnitude of this problem may be grasped.For a long time it has been apparent that it is mainly the bit itself that wears, and many attempts have been made to reduce the enormity of the problem by providing detachable steel bits which could either be used once and rejected, or sharpened three or four times before rejection.At the same time metallurgists have striven to 'improve the quality of the steel and the heat treatment afforded it so that a bit, readily workable In a normal mine drill-shop, could be produced having a high resistance to wear and fatigue; but, although various alloy steels have been marketed, it is still usual to find many mines relying on a "straight" carbon (0.6 - 0.9% C.) steel for their drill steels.Since 1915 increasing use has been made of tungstencarbide as a cutting implement in the engineering industry. Where, on account of its great hardness and long life, it...

Jan 1, 1948

By Enever J, Walton R, Wold M

Photoelastic and equivalent material model ling techniques for studying stresses and defor- mations and modes of failure in geological and engineering structures are described. The appli- cation of these techniques to the solution of tunnelling design problems is outlined. Models may contain heterogeneous components to simulate geological and man-made structures and may be two- or three-dimensional. Prototype construc- tion procedures and time dependent behaviour may be modelled. Examples of recent model studies carried out for the design of underground railway tunnels are given. Development of photoelastic and equi- valent material modelling techniques and facili- ties at the CSIRO, Division of Applied Geomech- anics are described, including a biaxial and triaxial frame for testing large scale two and three dimensional equivalent material models and components of full scale prototype structures.

Jan 1, 1976

By G E. Holt

Active EM subsurface imaging is a proprietary technique developed by Marschall Acoustics Instruments Pty Limited (MAI) to image subsurface features at depths useful for the mining industry. Similar in field operations to high resolution seismic surveying, the Active EM technique employs electromagnetic energy rather than elastic wave energy. Received backscattered energy in the Active EM technique is thus due to differences and contrasts in electromagnetic permeability and permittivity in the subsurface, analogous to LamTÆs constants in elastic wave imaging. Carrying the analogy to seismic imaging even further, the Active EM method employs high power transmissions of very wide-band coded signals of a controlled polarisation. Likewise, the array pattern and polarisation of the receiving transducers is also tightly controlled. Thus, in a certain mathematical sense, Active EM is the electromagnetic equivalent of high power high resolution vibroseis seismic surveying. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

This paper describes the operation involved in the sinking of a concrete-lined elliptical-shaped shaft at North Broken Hill Limited.Major factors such as geological features, future ventilation, ore haulage at depth and their relation to the location and selection of the type of shaft are described.Features covered in the sinking of the shaft include equipment details, with special reference to mechanical mucking, operational cycles based on time study analyses for sinking, concreting and the placing of steel sets. Safety precaution and statistical data is alsoincluded.INTRODUCTIONDue to the northerly pitch of the ore bodies in North Broken Hill Limited leases at approximately 42°, and the deepening of the active mining zone, it became apparent that No. 2 Shaft, the main operating shaft, would become unsuitable for the extraction of ore from the lower levels.Another major problem was the ventilation of the lower levels, and it was evident, that to ventilate efficiently these, and deeper levels, another upcast ventilation system would be required.Consideration was given therefore to the following: 1. Sink No. 2 Shaft from the existing bottom at 2770 ft. to 4200 ft., or Sink an internal shaft from the 2600 ft. level approximately 1000 ft. N. of No. 2 Shaft.2. Sink a new haulage and downcast shaft from the surface.3. Sink a new upcast ventilation shaft from the surface.It had been suspected that the ore bodies might flatten or even undergo a pitch reversal before reaching the...

Jan 1, 1956

The development of Mount Isa Mines Limited power supply is traced through the history of the mine operations. As would be expected, growth of the power supply system follows closely the increase in mine output, although it will be seen that total kWh. produced per ton milled shows a considerable reduction in later years when the mine output showed a more rapid rate of increase. That this reduction is not more marked is possibly due to the increased community and Shire Council power usage per head of population.INTRODUCTIONThe geographical position of Mount lsa, far from any large regional power supply Authority, dictated the policy that the Company be responsible for the production and suppiy of all power required for the plant operation. The Company also, in November 1937, accepted responsibility for the supply of a part of the power requirements of the township of Mount Isa. The history of power supply to the Mine may be divided into several phases.1. The supply Of lighting and power during the first plant construction period 1929-1931.2. The construction of the first section of the Mines Power Station, comprising Nos. 1 and 2 turbo alternators and boilers.3. The addition of No. 3 turbo alternator and boiler.4. The addition of No. 4 turbo alternator and boiler.5. The addition of No. 5 boiler.6. The addition of a. 2 turbo blowers for air supply to the Copper Smelter converters; b. 1 turbo blower for air supply to the L.ead Smelter; c. 2 turbo compressors for compressed air supply to the Mine and surface plant.

Jan 1, 1961

By J E. Everett

When ore is being selected from a regularised block model, a common procedure is to accept as ore any block whose iron content exceeds a cut-off value, and whose content in each contaminant analyte is below an appropriate cut-off value. This method defines a quadrant within the multidimensional analyte space, such that any block lying within the quadrant is accepted as ore and any block lying outside the quadrant is rejected as waste. The cut-off levels can be adjusted to maximise ore tonnage at a target grade (or analyte vector). When the method is applied to a project comprising multiple pits with systematically differing grades, it is found that ore tonnage at target grade is maximised if different cut-off quadrants are used for the different pits. This is apparently illogical, because it implies that an ore block from one pit may be accepted as ore, but an identical block from another pit is rejected as waste, even when ore from both pits is to be blended into the same product and there are no production cost differences between the pits. The paradox is an example of the ætheory of the second bestÆ: if there are multiple conditions for optimality and one condition is broken, then obeying the other conditions may not be the best policy. The problem lies with the quadrant cut-off method, which is shown to be inconsistent even for selecting ore from a single pit. A criterion that is inconsistent cannot be optimal. It is shown that a linear composite cut-off function provides maximum ore tonnage, and that a single composite cut-off criterion is consistent and optimal over multiple pits. Further, it is shown that a composite cut-off function not only maximises ore tonnage at a specified composition, but also can be used to select ore so as to maximise project value, if marginal costs and values are available.CITATION:Everett, J E, 2013. Selection of ore from multiple pits, in Proceedings Iron Ore 2013 , pp 185-192 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Elford H. S

Australia has many potentially important tin deposits, particularly on the eastern shore of the continent and in Tasmania. A number of these have been worked on a meagre scale, while some of them, because of metallurgical, transport, and other difficulties, have not as yet been developed.Believing that the full development of the tin fields of the Commonwealth of Australia is in part dependent upon the adoption of the most efficient methods of milling and smelting, the Development and Migration Oommission arranged for the first-mentioned author to visit the mining fields of Cornwall, one of the oldest tin-producing districts of the world, and prepare a report for the information of the Commission.This paper, now presented to the Australasian Institute of Mining and Metallurgy with the hope that it will assist the full development of tin mining in Australia, is the joint work of both authors.For over two thousand years tin has been produced from the Cornish mines. Even the ancient Greek historians made mention of tin mining in Cornwall, and it is probable that during the earliest periods the mining was alluvial. As early as 1602 a stamp battery working in Cornwall was described, and in 1671 calcination and buddling was a recognised scheme of treating pyritic ore. In the first half of the 16th century the output of tin from Cornwall was 700 tons per annum, and, from then on, production increased to the maximum in 1914 of 6500 tons. At present (Oct., 1929) the Cambourne-Redruth area produces over 95% of the Cornish tin output. This area includes such mines as the South Crofty, East Pool, Dolcoath, Parkanchy, Polhigey, and Wheal Kitty. The remaining 5% is largely supplied by the Levant and Geevor mines at Pendeen, St. Just area, near Land's End.

Jan 1, 1930

By Armoo K, Tran T

Cementation has been widely used in several hydrometallurgical processes for recovering gold and silver from process liquors. The process is electrochemical in nature, in which gold and silver are precipitated from the solution using less noble metals such as zinc, iron and copper. This paper summarises the current practice of gold cementation from cyanide liquors using zinc powder. Various developmental studies on the cementation of gold and silver from various systems (chloride and bromide) are also reported.

Jan 1, 1991

By J Naude

The TauTona (Sotho for Great Lion) Mine near Carletonville, which is one of AngloGold AshantiÆs most profitable operations in South Africa, has started a multi-million dollar expansion project that is expected to extend the operational life of the mine by at least three years. The project will also secure some 1900 jobs for existing workers and contract workers. The $US140 million project entails the development of the orebody to a record depth of almost 4 km underground. It means that TauTona, which already mines gold at the deepest levels in the world, will deepen its mining activities from 3600 m to a new record depth of 3910 m. There is great anticipation about the expansion program, especially because of new technology that will contribute to a safer working environment. It includes a simplified hoisting system that will minimise safety risks in conveyance activities. Due to the unique nature of this project, depth below surface and working through a three-tier shaft system, various innovative measures were incorporated into the planning of the endeavour. Special support equipment was designed to reduce cycle times and enable the crews to install the extensive support, prescribed by the mineÆs rock engineering department, right up to the face before every blast. Both declines dip at 23¦. The personnel/material (P/M) shaft is 4.4 m wide x 3.9 m high. This shaft is unique in that the conveyance will have an onboard driver. The rock shaft is 4.5 m wide x 3.6 m high. Rock will be hoisted with two, ten-tonne overturning skips. In both cases, P/M and rock, the winders were designed for the highest duty cycle, which is encountered during sinking.

Jan 1, 2005

By N Barnett, M Dello-lacovo, J Oh, S Saydam, T Pelech

In-Situ Resource Utilisation and Off-Earth mining require the application of horizontal drilling. The stability of such openings is challenging when excavating in the lunar regolith. Excavations on the Moon will encounter unconventional operational conditions such as different material properties, low gravity, and a moonquake. Micro-tunnelling or drilling to support lunar exploration and development of infrastructure on the Moon requires stability analysis to ensure its desired performance. The discrete element method (DEM) modelling technique has been utilised to investigate the optimum opening sizes on the lunar soil. From the literature, the mechanical properties of the lunar regolith have been reviewed and used for numerical model development. The model has been calibrated by simulating numerical triaxial tests with the Mohr–Coulomb failure criterion. Then, detailed parametric studies have been performed to investigate the influence of confinement, opening dimensions and moonquakes on the stability of openings. The findings have led to the development of a simple stability chart of the relationship between unsupported opening sizes and lunar regolith properties at different depths.

Nov 29, 2022

By C Standing, R Lacourt Rodrigues, C Q

The value of iron ore depends on the grade of the contaminants. Scheduled iron, and the associated contaminants, provides mine planners with a measure of stockpile feed and blending requirements. Blending at the stockpiles is one approach to optimising iron grade, while minimising the variability of contaminant grades. These schedules are typically based on resource models incorporating geology and iron and contaminant grades. Resource models reflect best estimates of trends for each of the elements rather than the potential variability, which is critical for accurate short-term blending. Conditional simulation provides a tool to describe the likely variability of each element. Only recently has conditional simulation technology allowed the inherent correlation between elements to be incorporated into the process. This paper presents the stepwise co-simulation process used to simulate and describe multi-element variability for effective mine planning. A case study using the multi-element conditional simulation and the subsequent uncertainty in the schedule and stockpile planning is presented. This process supports proactive mine planning to minimise unexpected fluctuations in the final product.

Jan 1, 2005

By Kurihara K, Tanimoto C

Construction and mining sites are often subject to unexpected flooding and extensive delays may occur in locating and installing emergency pumps. This particularly applies to sites located in remote areas. A simple and effective pump, called an air-lift pump, can be built from the equipment available at the working site. The basic req- uirements are a compressed air supply, air hose and conventional water pipes. The air-lift pump is comparatively in- efficient but approximately 35 per cent of the available compressed air power at the site can be applied to pumping. Suprisingly high liquid discharge rates may be obtained in suitable applications. The theoretical and practical consider- ations of the air-lift pump are evaluated and a suggested procedure for the emergency design and construction is outlined. INTRODUCTION. Sudden inundations of water into mine and development excavations require the immediate removal of the water if extensive and often irrepairable damage is to be avoided. Pumps installed in shafts or tunnels may become un- servicable due to being totally submerged during the flooding. The emphasis is on rapid

Jan 1, 1976

By R E. Conder

A major initial and ongoing cost component in many mining operations is that of transporting mined materials and processed ore from the point of extraction or processing to the next operation. For various reasons the transport distance can be significant or in some cases the route may be particularly challenging. The trend to higher production rates to gain economy of scale benefits and capitalise on sales opportunities means that optimisation of transport can play a significant part in profitability. Apart from the cost criteria, increasingly there are other criteria such as environmental restraints, land ownership and security of supply that can have a significant impact on determination of the optimum route and transport vehicle. The paper aims to briefly highlight the important selection criteria and the benefits and disadvantages of the most commonly utilised transport vehicles. It then moves on to looking in more depth at belt conveying, highlighting the unique capabilities of the Metso MRC Cable Belt Conveyor system.

Jan 1, 2004

By Cox N

Fragmentation control is perhaps the most critical aspect of quarrying operations, potentially impacting on the costs of all down stream processes, and sometimes even on the economic viability of an operation. The focal points of studies to control fragmentation are generally the pattern of blastholes, the accuracy of drilling, and the most appropriate powder factor. Recent studies suggest that the performance, and consistency of performance, of explosive detonation in the blastholes may also be a significant factor impacting on blast performance in hard rock quarries. This paper presents the results of studies of bulk emulsion and watergel explosive performance, using blasthole velocity of detonation measurements, and its impact on fragmentation. Field studies show a strong correlation between blasthole VoD and blast fragmentation. Another aspect of explosive performance impacting on ease of excavation of blasted rock is muckpile displacement, from which estimates of effective heave energy have been made for different bulk slurry (emulsion and watergel) products.

Jan 1, 1995

By G K. Robinson, M D. Sinnott

Three-dimensional granular flow models have been run to simulate three types of sample cutters: a cross-stream cutter, a vezin, and a cross-belt cutter. This type of modelling involves solving the equations of motion for large numbers of individual particles as they travel along a conveyor belt and interact with a sample cutter. It allows flows of bulk materials to be visualised and understood. Here we have used spherical particles. These results illustrate some advantages that modelling has compared to physical bias testing: By taking reference samples which are very close to the actual samples, the estimation of bias can be achieve quite precisely with very few runs. (Many Standards about bias testing recommend a minimum of 20 runs, but we have found that five runs generally provide adequate precision.) Potential bias can be divided into two components: the particles which are missed but should have been sampled and the particles which are extra but which should not have been sampled. This more detailed information can provide useful insight. Exactly the same material can be sampled using different sample cutters, thereby avoiding a source of variation that complicates physical testing. Much more detailed visualisation is possible, allowing better understanding of the bulk material flow in various circumstances.

Jan 1, 2005