Search Documents

By L O. ÆNeill, J Bebek

When Kalgoorlie Consolidated Gold Mines (KCGM) purchased its fleet of 18 CaterpillarÆs dump trucks in 1999, as part of its change to owner operated mining, five CaterpillarÆs Computer Aided Earthmoving Systems (CAES) were also commissioned on Komatsu PC8000 hydraulic shovels and Caterpillar D10R bulldozers. Since then the CAES system has been installed and operational on Komatsu PC3000 hydraulic shovel, CaterpillarÆs D10R dozers and Cat 994 front-end loader while Cat 854 wheel dozer has been fitted with CAESbasic. This investment in advanced machine guidance and control technology has proven very beneficial over the years for the Super Pit with improved safety and increased operating efficiency and productivity. The paper brings into focus how the CAES system adaptation in unique mining conditions assists in production gain, equipment operatorÆs safety, flexibility and independence, personnel removal from hazardous areas, acquisition of operational information and improvements in mine planning and design, benefiting the entire mining operation.

Jan 1, 2003

By N Strong

Cracow is a high-grade; low-tonnage underground gold mine located approximately 500 km north-west of Brisbane in Central Queensland. It is a steeply dipping, narrow vein, epithermal gold and silver deposit that is accessed via a decline from surface. Cracow is owned by joint venture between Newcrest Mining (70 per cent) and Sedimentary Holdings (30 per cent). The orebodies are 5 m wide on average and the ore is extracted via sublevel open bench stoping. Stopes are extracted to a strike of approximately 25 m before being backfilled with waste. Prior to the introduction of electronics, the mine would remove a small amount of the previous backfill out to create a void, and then begin blasting two to three rings at a time, with the ore being extracted between each blast. This method caused the ore to be blasted onto the waste backfill resulting in dilution of the high-grade ore. It also meant that the extraction of each stope took a number of weeks and numerous blasting events. In the fourth quarter of 2005, the mine struck a geotechnically sensitive stope, where all 20 rings had to be extracted in a single shot or risk possible geotechnical problems that could sterilise the ore. Due to the limitations of NONEL« delay detonators the mine could not fire all the rings in a single shot and needed to use an electronic detonator system to extract the stope. Some unexpected benefits to the mine were increased fragmentation, reduced vibrations, reduced dilution, improved efficiency and improved hanging wall and footwall conditions. After the success of this first electronic shot, the mine has since moved to firing all their stopes with electronic detonators. With electronics the mine has been able to fire much larger blasts, and has in fact moved to firing their blasts in the opposite direction, firing towards the draw point instead of into the waste backfill, thus reducing ore dilution.

Jan 1, 2008

By Van Weert G

Ferrous chloride solution pyrohydrolysis is a successful IICI regeneration process which is carried out in either a spray roaster or a fluid bed. Pyrohydrolysis is not restricted to ferrous chloride only, every metal chloride can theoretically be hydrolysed. In practice, however, the conditions for ferrous chloride pyrohydrolysis differ from those of many non-ferrous metal chlorides eg zinc, lead and cadmium. Hence, a pyrohydrolyser could function as a ferrous/non-ferrous separator, eg an iron oxide and zinc chloride separator. Most pyrohydrolysers operate on solutions, in which case more than 50 per cent of the process energy is needed for heating and evaporating water. However, this disadvantage would be diminished by feeding a slurry to the reactor. Against this background it was decided to investigate the chloridisation of zinc ferrite which is an iron bearing solid with a non-ferrous impurity, and subject to processing and disposal problems. Synthetic zinc ferrite was chloridised in a tube furnace. The gas atmosphere in the tube furnace resembled that of a fluid bed pyrohydrolyser and consisted of HCI, 1120 and nitrogen. Gas composition, temperature, residence time and sample mass were varied. The experiments showed that complete (99.6 per cent) zinc extraction from synthetic zinc ferrite was possible in a simplified pyrohydrolyser atmosphere at 1100 K in four hours. The zinc ferrite was converted into gaseous zinc chloride, and hematite and magnetite solids. It was also found that zinc removal from the zinc ferrite lattice caused not only rccrystallisation of the zinc ferrite into hematite, but also hematite crystal

Jan 1, 1993

By Wheatley MR

Answers to the questions "which rocks contain diamonds?" and "which indicator minerals should diamond explorers look for?" are no longer so easily obtained, now that diamonds are known to occur in lamproites and various types of lamprophyres, as well as their traditional source of kimberlites. One way of isolating those factors (host-rock"geochemistry, geographical or tectonic location, xenolith minerals, etc.) which are most critical in determining the diamond potential of a given pipe, is a detailed and critical re-examination of the huge volumes of accumulated data on kimberlites, lamproites and related rocks. A large analytical database to this end has been set up on an Apple Macintosh II microcomputer using the quasi-relational database management system 4th Dimension. Currently, it contains data for up to 90 major and trace elements, isotopic ratios and contained mineral compositions for some 4,000 rock specimens from all over the world. Many experiences in setting up this database are probably relevant to other geologists setting up their own systems: they include determining the relationships between data items; the advantages of codes over free text in representing categorical variables such as rock types; the need for rigorous error trapping and data validation; and the problem of missing data values and ambiguities thereof. The working system is now being used in a rigorous statistical assessment of the criteria which distinguish diamondiferous from non-diamondiferous rocks.

Jan 1, 1989

By Taylor G. R

Fluid inclusions within quartz accompanying several stages of mineralization at Hillgrove are de cri bed. Pyrite-arsenopyrite-gold mineralization shows uncorrected filling temperatures of between 195°C and 250°C. Later stibnite-antimonide-siderite and stibnite-calcite mineralization has filling temperatures between 100°C and 195°C and a bimodal distribution of temperature peaking at 175°C and 145°C, possibly correlated with the two stages of mineral deposition. Secondary included fluids within an earlier generation of deformed quartz veins are derived from hydrothermal fluids contemporary with the main-stage mineralizing fluids described above. Primary inclusions within latestage, cross-cutting quartz-chlorite-calcite veins show these veins to be unrelated to the mineralization.A correlation between filling temperatures and salinities indicates that mineralization accompanied the mixing of a hot, partly saline, fluid (at 5 per cent equivalent NaCI) with cooler, less-saline meteoric or connate water. Over a vertical distance of 200 m, equivalent mineral assemblages were deposited over the same temperature range. Studies on single crystals suggest rapid deposition with fluid temperature dropping 45°C during their growth. Ore mineragraphy and the fluid inclusion data suggest that the metals were transported by sulphur-poor, relatively low-temperature, low-salinity solutions, possibly as carbonate complexe , and that a vertical zonation of the W-Sb-Au mineralization is compatible with the mixing of this hydrothermal fluid with cooler groundwater. Regional metallogenic and geological considerations suggest that ore metals are derived from the remobilization of deep-seated stratabound deposits or from metamorphic fluids expelled from deepseated volcanoclastic sediments.

Jan 1, 1984

By J Player, K Braddon

High productivity mining is the key to the financial success and stability of modern mines. This can be achieved through the use of new technologies, the development of innovative work practices andoptimisation of the mining method to suit the mining environment.Big Bell Mine is a 1.7 Mtpa longitudinal sublevel caving operation at a head grade of 3.14 g/t. Annual production is 170 000 ounces of gold. The selection and implementation of bulk emulsion explosives was seen as the logical progression from blow loaded ANFO for the high tonnage rate required from the longitudinal sublevel cave.Prior to the implementation of bulk emulsions an investigation wasrequired to examine the technical and financial benefits available with the introduction of bulk emulsion. This paper examines the review process and the successful implementation of bulk emulsion explosives at Big Bell.

Jan 1, 1999

By I Brunton

Blast fragmentation can have a significant impact on the profitability of a mine. An optimum run of mine (ROM) size distribution is required to maximise the performance of downstream processes. If this fragmentation size distribution can be modelled and controlled, the operation will have made a significant advancement towards improving its performance. Blast fragmentation modelling is an important step in Mine to MillTM optimisation. It allows the estimation of blast fragmentation distributions for a number of different rock mass, blast geometry, and explosive parameters. These distributions can then be modelled in downstream mining and milling processes to determine the optimum blast design. When a blast hole is detonated rock breakage occurs in two different stress regions û compressive and tensile. In the first region, compressive stress waves form a æcrushed zoneÆ directly adjacent to the blast hole. The second region, termed the æcracked zoneÆ, occurs outside the crush one. The widely used Kuz-Ram model does not recognise these two blast regions. In the Kuz-Ram model the mean fragment size from the blast is approximated and is then used to estimate the remaining size distribution. Experience has shown that this model predicts the coarse end reasonably accurately, but it can significantly underestimate the amount of fines generated. As part of the Australian Mineral Industries Research Association (AMIRA) P483A Mine to MillTM project, the Two-Component Model (TCM) and Crush Zone Model (CZM), developed by the Julius Kruttschnitt Mineral Research Centre (JKMRC), were compared and evaluated to measured ROM fragmentation distributions. An important criteria for this comparison was the variation of model results from measured ROM in the fine to intermediate section (1 mm to 100 mm) of the fragmentation curve. This region of the distribution is important for Mine to MillTM optimisation. The comparison of modelled and Split ROM fragmentation distributions has been conducted in harder ores (UCS greater than 80 MPa). Further work involves modelling softer ores. The comparisons will be continued with future site surveys to increase confidence in the comparison of the CZM and TCM to Split results. Stochastic fragmentation modelling will then be conducted to take into account variation of input parameters. A window of possible fragmentation distributions can be compared to those obtained by Split. Following this work, an improved fragmentation model will be developed in response to these findings.

Jan 1, 2001

Every text book for blasting in Japan says that Hauser's law can be applied for practice. But recently it came true that there was no historical record about him and no actual datum of his own or other's to testify. According to his theory, the funnel ratio N = r/W in crater test is inversely proportional to the rock strength and proportional to the explosive amount: where r is the radius of crater and W is the burden. But experiment showed the opposite result, and revealed new information. Two kinds of experiment, crater test and boulder blasting of mortar, were carried out to investigate the effects of rock properties on blasting. The material used for test 1 and test 2 was a mortar block (60cm)3 cube, 4 vertical faces of which were used for crater test. The results from Test 1 and test 2 were summarized as follows. The funnel ratio ranges between 2.5 to 4.5 in proportion to rock strength and burden. The standard ratio of 1, reported by Hauser, was not observed in any instances. It was also noted that the funnel ratio is independent of the explosive amount. The material used for boulder blasting, test 3, was a mortar block (40cm)3 cube, in the middle of which was located a vertical borehole for the explosive charge. The results of test 3 were as follows. The necessary explosive amount for boulder blasting is in inverse proportion to the mortar strength. Fragmentation and throw are proportional to the mortar strength.

Jan 1, 1990

The Golden Pig Mine is wholly owned by Bunnine Operations Limited and is located in the Yilgam Goldfields at Southern Cross, Western AustraliaThe paper briefly describes the geology and history of the operations. Mining is by shrink stoping, both hand held and mechanised. Advantages and disadvantages costs of the mining system are discussed.

Jan 1, 1993

By Gemmell J. B

Zinc-bearing massive sulphide deposits have been mined in Tasmania since 1900. The current major producers are Hellyer and Rosebery, with total resource tonnages (mined plus reserves) of 16 Mt (million tonnes) and 24.8 Mt respectively. These deposits belong to the class of seafloor volcanic-hosted massive sulphides (VHMS) and are located within the Mt Read Volcanics, a narrow belt of continental margin calcalkaline volcanics of Cambrian age. Compared to other Australian VHMS deposits, and world-wide MVT and Sedex deposits, the Tasmanian examples clearly stand-out due to their high metal grades, averaging over 17 per cent Pb+Zn. The deposits vary in morphology from mound style (Hellyer) to sheet style (Rosebery) with other combinations including stacked lenses (Que River) and disrupted cross-cutting bodies (Hercules). All deposits show the classic VHMS zonation from an Fe-Cu-bearing base to a Zn-Pb-Ba-rich top. Zinc, gold and silver tenor commonly increases toward the stratigraphic top of the deposits. The ores have been deformed during regional metamorphism, resulting in folding, shearing and recrystallisation of sulphide lenses. In addition to the major deposits, a number of small massive sulphide prospects occur throughout the volcanic belt and the potential for the discovery of further large, deeply buried deposits remains high.

Jan 1, 1993

SITUATED in the county of Manchcster, in Northern Eyre's Peninsula, the Iron Knob ore-deposits form the basis of the industry. These deposits are connected by the Iron Knob tramway to the port of Whyalla, aal miles distant, on the western shore of Speneer Gulf,and to-day another tramway is under construction to link up with the same port, a second group of iron ore leases known as Iron Baron, which is situated 18 miles south of Iron Knob. Fig. 1 indicates the geographical relationship of these three places, Iron Knob, Iron Baron, and Whyalla, which together comprise this field of the company's activities.

Jan 1, 1930

By Parker C. J, Mikula P. A

The excavation for the Sydney Opera House Parking Station comprises a large donut shaped underground cavern with a central sandstone pillar. The maximum effective roof span is about 19 m and the rock cover is between 7 m and 8 m. Permanent support for the roof and the various services tunnels consists of a combination of tensioned anchors, and untensioned dowels, and mesh with shortcrete and fibrecrete as the final lining. Steel sets were installed at main intersections.Fundamental to the design philosophy for excavation of these spans at such shallow rock cover was the use of monitoring to check on the adequacy of the installed support. Prior to excavation, extensometers, inclinometers, piezometers and surface settlement survey stations were installed. Underground survey stations, anchor load cells and shotcrete pressure cells were installed as excavation proceeded. Excavation commenced at the crown using an initial heading and three widening stages. Geological mapping during excavation confirmed borehole expectations, namely sandstone beds 1 to 4 m thick interbedded with thin shale units. Bedding plane contacts varied over short distances from tight partings to thick brecciated seams. Jointing was subvertical and joints tended to be bed-limited.

Jan 1, 1993

By S Servant

In the mine of this study, cemented hydraulic backfill is placed under the form of a slurry at a percentage of solid by weight varying from 50 to 65 per cent. This slurry settles and cures in the stope. During this process an important amount of water must be drained from the stope. Field observations in the case studied here show that the geometry of the drains system has a significant impact on the drainage of the stopes. The mode of filling produces a backfill showing an evident stratification typical of a sedimentation process. In situ observations on this material show that this stratification translates into a very strong heterogeneity in the physical properties of the cemented backfill. This heterogeneity should affect the hydraulic conductivity of the backfill in the stope. In order to study this aspect, finite element simulations were performed. This paper presents the results of these simulations, where the impact of this stratification on hydraulic conductivity is related to the performance of the backfill drainage system for various geometry. This preliminary study is aimed at providing a better understanding of the role of the drains in the dewatering process of the backfilled stope in the case of this mine.

Jan 1, 1998

The Bendigo goldfield is centred on the urban area of Bendigo (population approximately 60 000) in central Victoria, 130 km north west of Melbourne, Australia. Gold was discovered at Bendigo in 1851 and production continued through to 1954. The Bendigo goldfield is the second largest goldfield in total gold produced in Australia, after KalgoorlieÆs Golden Mile with a total production of 22 million oz. The geology of the Bendigo Field consists of a series of tightly folded, interbedded sandstone and shale sediments. Within the sediments the gold mineralisation is hosted in quartz reefs or ribbons closely associated with anticline axes and reverse faulting. The gold within the quartz reefs is typically both coarse grained and erratically distributed.

Jan 1, 2002

By W T. Pate, A V. Potapov, J K. Lichter

Even though flotation is one of the most important unit operations of mineral processing, accurate modelling of this process for plant performance prediction has remained elusive. In the last four to five years dramatic changes have occurred in our ability to make credible model based predictions. This paper briefly traces the history of flotation modelling from simple (lumped pulp-froth) æchemical kinetic analogueÆ models for single cells to more detailed multi-phase, multi-component population balance models for banks of cells. It then focuses on recent developments in physics-based modelling tools. This includes current efforts to model the forces of attachment and detachment at the individual event level as well as multi-event levels in individual cells and circuits. Two examples of these tools are presented. The first is DEM modelling of the mechanics of motion of bubbles in froths. The second is population balance modelling of the dynamics of flotation circuits describing how they are influenced by upstream processes (such as crushing and grinding) as well as internal process variables (such as aeration, agitation and reagent addition). Applications of each of these tools are discussed.

Jan 1, 2005

The published safety policy of Mount Isa Mines Limited, together with details of the organisation and control techniques adopted by management to pursue an active safety programme within the company, is presented. The importance of communication by management through the organisational hierarchy and procedures instituted to ensure rapid and concise feedback on safety concerns are detailed. The paper also describes the role of the occupational health department and safety committees in assisting management to monitor the safety effort of supervisors and employees. Current safety performance levels are tabled together with details of some aspects of the programme on which safety effort will be concentrated in the future.

Jan 1, 1975

By G Showers, R Triglavcanin

The complexity of understanding the whole thickening process to achieve real performance improvements cannot be underestimated. The last significant change in feedwell design was more than 15 years ago with the introduction of self-dilution systems û firstly with OutotecÆs Autodil, followed by FLSmidthÆs E-Duc. Now, following many years of extensive in-house research, including close collaboration with AMIRA and the CSIRO, Outotec has launched the next generation Vane Feedwell. The Vane Feedwell has been globally patented and installed at various sites. This paper briefly outlines the feedwellÆs development using CFD modelling and its subsequent performance in a æreal lifeÆ site installation. Plant results of the first commercial Vane Feedwell, in a mineral sands application, are discussed. The Vane Feedwell was retrofitted so comparative data of pre- and post-installation is shown.

Jan 1, 2009

A number of cooperative studies have been carried out as preliminary work for drafting a standard for application of granulated slag sand for concrete, and the following conclusions were reached 1 The ten kinds of granulated slag sands pro- duced in Japan satisfy the national standard for fine aggregate in terms of physical and chemical properties. 2 Mortar and concrete tests conducted with granulated slag sand revealed that, although with slight differences in the extent, gran- ulated slag sands used in these tests were applicable'as fine aggregate for concrete, 3 The pumpability test by a concrete pump carried out on concrete with two kinds of now commercially available granulated slag sand demonstrated that the pump pressure feeding is applicable in the same manner as in the case of ordinary concrete. These tests permitted' preparation of a draft standard for application of granulated slag sand, and the results formed the first step toward utilizing this material as a sub- stitute for natural sand.

Jan 1, 1979

By Semple DG, Leach TM

A continued exploration programme has further defined the geology of the Tolukuma vein system, verified the resource indicated by Newmont, and identified potential for additional mineralisation. The resource at Tolukuma Hill, designated as Zone C, is a measured 440,000t @ 17g/t Au and 46g/t Ag with an additional indicated resource of 120,000t @ 16g/t Au. A diatreme breccia localised at an intersection of structures, and a relationship of gold to base metal sulphides, are highly indicative of a porphyry association. Typical epi-thermal features such as crustiform banded quartz and quartz pseudomorphing. platy calcite are also present and locally contain lesser gold mineral-isation. Pre-existing dilatant structures have acted as a host to the ore fluids, resulting in the formation of the semi-continuous Tolukuma-Gulbadi veins over a 1100m strike. A fluid flow model suggests that mineralising fluids were sourced from the diatreme margins and migrated laterally along dilatant structures. Bonanza gold grades are derived through fluid quenching in the flexure between a hanging wall split which hosts much of the Tolukuma Hill resource and the feeder graben structure. Thus, the relationship between the pre-mineral structural geometry and fluid upflow at the margins of a diatreme breccia, controls the ore setting. Potential for more ore remains within the Gufinis and the 120 veins as well as in the outlying Prospects.

Jan 1, 1994

By M Kongas, K Saloheimo

Concentrating lower and more variable grade ore resources to meet acceptable concentrate quality criteria requires removal of significant amount of gangue minerals. Monitoring plant feed mineralogy and concentrate by on-stream analysis has significant economic benefits in concentrate quality and recovery optimisation. There is a need to develop a sensitive slurry on-line analyser for silica, aluminium, magnesium and other light elements.On-line XRF elemental analysis technology, which is a routine practice in base metal concentrators is not able to measure lighter elements than calcium from slurry. Too much of the X-ray fluorescence signal from lighter elements is absorbed by water. The limitations in the direct measurement of silica and other light elements have restricted its use in some applications. Some light element slurry analysers have been developed based on prompt gamma neutron activation (PGNAA) method but they have not performed up to the expectations. This paper describes a new on-line elemental slurry analyser and the results of on-line laboratory tests.CITATION:Kongas, M and Saloheimo, K, 2013. Online light element slurry analysis, in Proceedings MetPlant 2013 , pp 93-101 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013