Search Documents

By E. V. Manlapig, B. K. Gorain, N. W. Johnson, K. Ward

A flotation model developed at the Julius Kruttschnitt Mineral Research Centre was used to predict the performance of copper rougher and scavenger circuits at the copper concentrator at Mount Isa Mines. The model describes the kinetic response of an ore in a flotation cell in terms of ore floatability, cell characteristics and froth recovery. The floatability parameters of the rougher feed ore were obtained directly from a detailed plant survey. Flotation analysis was carried out for twenty different size-by-liberation classes to account for the effects of particle size and liberation on flotation. This paper investigates the capability of the model to predict the flotation behavior of 20 different size-by liberation classes in the rougher and the scavenger banks.

Jan 1, 2000

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH's Pittsburgh Re¬search Laboratory showed that electrical current levels permitted under present regulations may not limit cable temperatures to less than 90°C in reeled trailing cables. Reeled cables, which are tightly wrapped with many turns and which carry current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften, making them prone to damage. The damaged insulation reduces the life of the cable and can lead to shock, electrocution and mine fires. This paper describes a method of measuring the conductor tem¬perature of mine trailing cables during normal operation. The temperature is measured using a 50/125-, µm graded index multimode optical fiber located in the center of the metallic conductors. Distributed temperature measurements are made using an optical time domain reflectometer (OTDR). This system is capable of measuring temperatures with an accuracy of ± I °C over a length of 4 km at I -mintervals. With this unique way of measuring temperature, tests can be conducted that simulate actual mine conditions. The tests provide important data that allows MSHA's Approval and Certification Center to develop approval criteria for cycli-

Jan 1, 2000

By Paul H. Lu

This paper proposes a novel method, "integrity factor approach," of mine-pillar stability evaluation based on in situ triaxial-loading measurement. The pillar integrity factor is defined as the quotient resulting from division of integrated total pillar strength across the critical dimension by the integrated total pillar load across the same dimension. The integrity factor is dynamic, while the conventional safety factor is static. With this approach, the pillar stability can be evaluated at any stage of mining progress during panel operation. It automatically considers the progressive failure of the pillar and post-failure strength without the need to clearly define the boundary between yielded and intact zones of the pillar. Based on two case studies, the integrity factor approach is shown to be a practical, effective technique for evaluating stability of conventionally designed pillars. It is suggested that a more realistic estimate of in situ pillar strength could be made based on the combination of in situ triaxial-loading measurements and laboratory true triaxial compression tests, rather than through the traditional combination of biaxial-loading measurements and conventional triaxial compression tests.

Jan 1, 1986

By B. J. Arnold, F. F. Aplan

Prior laboratory work has demonstrated that much of the fine ash forming minerals entering a flotation froth are there as a result of water carryover- from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 8.5 m3 (300 cu ft) Wemco flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent solids in the froth). Reagent changes that result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1991

By Robert S. Mayo

The haulage of muck from mines was first illustrated by Georg Agricola in De Re Metallica in the year 1556. In many of his ancient wood cuts he showed a crude car running on wooden rails. These wheels had no flanges. There were four pins sticking down from the car to guide it along the rails. Eventually they made the wheels of cast iron with flanges on them. In England, coal was hauled from the pit mouth to the nearest river or canal in "wains", or wagons, running on the common highways. These wains carried one chaldron of coal, weighing 2500 lbs and it took six horses to haul these wains over the atrocious roads of that day. Somebody, about 1760, invented a cast iron rail. These were cast iron troughs, 4 ft long laid on wooden sleepers. With these iron rails they found that one horse could do the work of six. But this U-shaped groove trapped all the dirt and grit. Somebody had the brilliant idea of attaching a flange to the inside of the wheel and from then on the rails were of timber protected against wear by a strap of iron. Rolled rails, of wrought iron, were first used in England in 1820. I am sure that many of you people have wondered why the British and American railroads standardized

Jan 1, 1974

By J. H. Fewings

The rapidly escalating capital costs for new projects, or extension of existing projects, has placed greater emphasis on maximum use of existing resources. Thus, when increased grinding capacity was required to achieve metal production from lead-zinc ores a number of alternate approaches were studied. The most cost effective way of achieving the required 5% increase in grinding circuit capacity was to install upgraded instrumentation and computer control of grinding - Fewings, Wickham and Wiseman (1). Once the computer installation cost had been borne by the financial returns from that project, other projects involving computer control were economically viable on an Incremental cost basis. These Included centralised control of tailings thickening and return circuit water distribution, centralised control of the crushing plant and use of the computer as a data processor for an on-stream analysis system for flotation slurries.

Jan 1, 1979

By S. C. Suboleski, R. Zhao

A Simulation/Animation Model (SAM) with several unique features has been developed for continuous mining in room-and-pillar production systems. Initial cut data are generated by the program based on a short list of general section parameters, and is graphically displayed on the screen for checking and editing. This portion of the program includes several intelligent features. For example, a different cut sequence will be generated for uni-directional section ventilation than for bi-directional flow. Once the data are accepted, the entire simulation may be viewed in animation. Effectively, much of the data are checked visually by watching the actions of the mining equipment. Following the simulation, results are summarized as bar and pie charts, as well as printed output. In addition to the extensive use of graphics, the program contains several advances in simulation techniques as well.

Jan 1, 1993

By Frank S. Hicks, Y. Charles Guan, Glenn A. Gruber

This paper describes a two-part program funded by the Florida Institute of Phosphate Research and performed by Jacobs. The first part of the program was to examine the application of ultrasonic treatment to clean phosphate particle surfaces. Florida phosphate pebble and rougher flotation feeds were treated in an ultrasonic trough to remove clays. Also, the de-oiling of rougher concentrates by ultrasonic treatment was tested. In order to improve the clay removal efficiency, viscosities of primary cyclone overflow from six beneficiation plants were studied in the second part of the program. Viscosities for different samples at the same clay % solids vary significantly, and increase exponentially with clay % solids content for the same sample. A method of controlling cyclone operation using on-line viscosity measurements and pump box level sensors is proposed to logically improve primary cyclone performance.

Jan 1, 2002

By W. E. (Bill) Stanley

Introduction This is an exciting day. It isn't often that you can find the best minds in a particular business gathered together in one place. But that is what we have here. You are the best and the brightest people there are in the business of gold mining. What we discuss at this conference confirms the major issues facing us and sets out the issues governing how our mines and mining companies will be run in the next few years. In looking over the list of papers to be given, I have noticed something. It is something that I have noticed at almost every mining convention I have ever attended. Almost every paper at this conference concerns itself with the technical side of mining. Most of us in this roan are professionals; we are either engineers, geologists, accountants or representatives of some other profession. In getting where we are today, we have had to work hard to acquire the technical skills needed for our individual professions. We are all proud of our knowledge and work hard to claim the right to be considered an expert in a particular technical field or subject area.

Jan 1, 1987

By Hajime Miki, Michael J. Nicol

Relatively simple techniques have been developed which enable the electrochemistry of sulfide minerals to be studied with particles varying in size from above 100 pm to less than 1 pm. Both oxidative and reductive processes have been studied wing the minerals pyrite, arsenopyrite and chalcopyrite. It has been shown that it is possible to completely oxidise or reduce the minerals during a single voltammetic sweep. The resulting voltammogram produces peaks which are characteristic of each mineral and can be used to qualitatively identify the minerals. In the case of chalcopyrite, it has been demonstrated that the charge involved in the anodic oxidation can be quantitatively related to the amount of copper dissolved. Quantitative information can be obtained using peak fitting techniques. Interesting differences in the behaviour of the minerals in sulfuric and hydrochloric acids have been observed, particularly in the case of pyrite for which a second major peak is obtained which has been attributed to the oxidation of elemental sulfur in the presence of chloride ions. The technique offers the possibility of providing mineralogical information of individual particles based on an electrochemical voltammetic finger print.

Jan 1, 2005

By R. G. Eggert, M. R. Walls

A mining CEO's willingness to participate in risky investment opportunities significantly affects a company's strategic-investment decisions. Decision-analysis techniques provide a mechanism for measuring a CEO's risk tolerance and ability to make formal comparisons of risk propensity among mining firms. The authors developed a methodology for measuring CEO risk tolerance. The findings from a confidential survey of mining CEOs are presented. The results from the survey suggest that: •mining CEOs are overwhelmingly risk averse when considering investment decisions; •CEOs of small mining firms are significantly more risk averse than CEOs of large mining firms; and •there appears to be some differences between Australian and non-Australian CEOs regarding their willingness to participate in risky investments. The results of this survey suggest that CEOs are pursuing objectives other than, or in addition to, maximizing shareholder wealth and that they act to reduce the financial exposure associated with strategic investments.

Jan 1, 1997

By J. S. Hattrup

INTRODUCTION Tunnel boring machines in non-abrasive competent rock with little or no water have set new performance standards in the driving of tunnels. However, when the machines have hit blocky or running ground, they have encountered difficulties. The success of a tunnelling machine is usually due to a thorough geological investigation which accurately describes the rock conditions, a well designed tunnel support system, and a tunnel boring machine designed to cope with these conditions. In some cases machines have had to be modified in the tunnel after the machine had commenced boring, because geological conditions were not correctly anticipated before tunnelling began. The features described herein are not a panacea for all conditons, and some of them, like an auxiliary thrust system that thrusts off a precast invert segment requires pre-planning of work on the part of the contractor. CUTTERHEAD DESIGN Figure 1 shows typical cutterheads of ten to fifteen years ago. Note the large buckets and large openings between the buckets. These large openings were considered necessary to gain easier access through the cutterhead for cutter changes. The standard cutter in those days was an 11 inch or 12 inch cutter with small bearings, and was generally a delicate tool for the duty it was to perform. These large buckets would clog up if a formation with clay seams was

Jan 1, 1981

By J. Pang, S. Chander

The results of an investigation to characterize the chalcopyrite/solution interface are presented. Several techniques were used, including galvanostatic and steady-state polarization, cyclic voltammetry and impedance spectroscopy. The results show that the dissolution of chalcopyrite was incongruent. Initially, at low potentials (< 0.12 V), iron species were released that led to the growth of an iron-deficient sulfide (IDS) layer (referred to as the "reacted layer" in this paper). Depending on the solution&apos;s composition, the dissolved iron might reprecipitate as a hydroxide layer. In the potential range of 0.12 V < E < 0.23 V, the IDS layer was passivating. In comparison, development of a passivating IDS layer under galvanostatic conditions led to a jump in potential to 0.48 V. The IDS layer began to dissolve at potentials greater than 0.24 V. The dissolved species precipitated to form a product layer in alkaline solutions. Continued oxidation involved diffusion of species through the reacted and product layers. At higher potentials (> 0.48 V), further oxidation led to the dissolution of the copper and sulfur species, with a resultant breakdown of the IDS layer. The changes in surface-coating properties, resulting from various electrochemical treatments, are discussed.

Jan 1, 1993

By John C. Cook

In reasonably dry rock, long-wave radar can theoretically explore to distances approaching 75 meters (250 ft). High-resolution radar reflections have already been demonstrated through 13 m of hard limestone, through 9 to 18 m of coal in place and through 225 m of rock salt, using only low-power experimental radar equipment. Radar reflections have been received through the rock from rough pillar walls, from faults, and from a slim, uncased, vertical drill hole. In three years of intermittent experimentation, the feasibility of rapid radar exploration of large volumes of rock, with portable equipment, in deep, wet workings has been demonstrated. With future, improved equipment the theoretical working range, of the order of 75m, is expected to be attained in most hard rocks. THE TECHNIQUE Fig. 1 illustrates an early "monocycle" radar system (1) set up in a coal mine. This radar equipment is entirely different from that employed for detecting distant objects through the atmosphere. However, the basic principle is the same: a pulse of electromagnetic energy is radiated by the transmitter, a portion is reflected by some "target" object embedded in the surrounding medium and some of this energy is collected by the receiving antenna. In the receiver, the pulse is amplified, is "stretched out in time" by a sampling process, and is displayed on the screen of a cathode-ray oscilloscope. It may also be recorded on paper or magnetic tape. Fig. 2 illustrates a

Jan 1, 1997

By Gordon D. House, J. B. P. Sawyer

The Bannockburn gold prospect is a new discovery in Ontario&apos;s oldest gold camp at Eldorado, eastern Ontario. Mono Gold Mines Inc. of Vancouver, British Columbia, acquired the property in 1980 and in 1984 discovered a previously unreported gold bearing quartz vein system to the northeast of the old Bannockburn Mine. Extensive diamond drilling carried out since 1985 defined a quartz vein system over 475 m (1 ,500 ft) of strike to a depth of over 105 m (350 ft). Limited underground exploration by decline to the 22.9 m (75 ft) level in 1988 confirmed the continuity and tenor of the quartz veins. Gold occurs as native metal with minor sulphides and bismuth tellurides in a quartz carbonate vein system within metasedimentary and metavolcanic rocks of the Grenville Province. Metallurgical test work on a surface bulk sample was favourable. Estimates of drill indicated reserves have been made as well as reserves based on the limited underground exploration.

Jan 1, 1989

By Bruce W. Cavender, Brian L. Granger

The leaching characteristics of non-homogeneous ores have traditionally been difficult to assess in laboratory tests. A result of the large sample size necessary to ensure representativity, this difficulty is most acute for ores containing nuggets or other irregular occurrences of precious minerals. Consequently, small-scale leaching tests are often regarded as indicative rather than conclusive. The predictive nature of leaching tests can be improved by applying the experimental design concepts of blocking and randomization. In the case of column leaching, experimental &apos;blocks" are constructed with the same number of columns as there are separate test conditions. These blocks are treated identically throughout the test, with differences between columns within each block being the variables of interest. To maximize the uniformity of the blocks, randomization procedures are employed in the preparation of the sample and conduct of the test. The initial ore sample is screened and individual column charges composited from randomly selected increments from each size fraction. The leaching order, daily solution analyses, and processing of leach residues are similarly randomized. The observed differences in leaching performance between the columns in each block are compared to determine the over-all outcome of the test. A statistical analysis using t distributions gives a quantitative measure of the reproducibility of the outcome.

Jan 1, 1995

By J. F. Stenebråten, W. P. Johnson, D. R. Brosnahan

Carbonaceous materials (CM) from ores of varying preg¬robbing activity from Barrick Goldstrike Mines Inc. (BGMI), Nevada, were characterized in terms of their functional group contents, hydrocarbon contents, elemental composi¬tions and humic acid contents. Fourier transform infrared (FT-IR) analyses did not show the presence of hydrocarbons or carboxylic, phenolic or sulfhydrolfunctionalities. The FT¬IR bands present included C=C stretching in aromatic rings and C-O-C stretching, indicating the presence of oxygen as ether linkages or thiocarbonyl functionality in the carbon matrix. Calculated atomic oxygen to carbon (O/C) ratios did not reveal a trend between the maturity of the CM and the preg-robbing behavior, possibly due to the low resolution inherent in electron microprobe analyses. However, the atomic O/C ratios agree with other chemical analyses, indi¬cating that the organic carbon is very mature, similar to or higher than anthracite grade coal. Gas chromatography¬mass spectrometry and nuclear magnetic resonance analy¬ses corroborated the relatively featureless character of the carbon, indicating that the carbon structure is virtually completely aromatic (graphitic).

Jan 1, 2000

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by the National Institute for Occupational Safety and Health&apos;s Pittsburgh Research Laboratory. Investigated were a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal-extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. In laboratory experiments and in a longwall field evaluation, the translucent mesh barrier was shown to provide notable dust-control effectiveness for a distance of up to 60 m downstream of the shearer, provided that the mesh barrier remained relatively parallel to the airflow. The staged spray barrier system showed marginal dust-control effectiveness in the laboratory and, therefore, was not field tested.

Jan 1, 2000

By John F. Shea

When tunnel boring machines were first developed, the J. F. Shea Company elected not to use them until some of the bugs were worked out. When we did take the plunge, we learned a great many lessons in tunneling; amongst others, that tunneling with a TBM is more an art than a science. One of the most important factors that contributes to a successful TBM tunnel is the geology. A machine can be designed to handle almost any type of ground; however, if the ground is not uniform, compromises in design must be made to enable the machine to handle the various ground conditions. Even when the geologic formations are well defined, it is still impossible to predict how the formations will react when it is penetrated by a tunnel. This is where the design and performance of a tunnel boring machine runs into trouble. When the reactions are adverse, the contractor is left with three alternatives; park or pull the machine and drive conventional, fight through the formation with no changes, or modify the machine. We have made all three of these choices. The first, on the Tonner Tunnel in Southern California, we encountered an extremely tough sandstone where progress was measured in inches per day. Ultimately, we pulled the machine and drove conventional tunnel. The second, on the Vat Tunnel in Central Utah, another element was added to the geology - water, which we encountered in excess of 1,000 gpm at the heading. It was impossible to adapt the machine to handle this much water, so we have been carrying out a program of grouting ahead of the machine and then driving tunnel with the tunnel boring machine.

Jan 1, 1981

By K. V. K. Prasad

Solution of most engineering problems requires, in addition to vast numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity. However, it is only recently that approaches like the expert systems methodology have been developed to incorporate the judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or "shells" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development of a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.

Jan 1, 1989