Search Documents

By E. R. DeMen

In late 1965 General Mills announced the availability of a new liquid ion exchange reagent, LIX®-64, for the recovery of copper from various solutions, such as dump leach liquors. Acceptance of this material by the copper industry has been gratifying. A number of pilot plants have been operated, and at this writing there are four commercial plants either in operation or under construction. The properties and operating characteristics of this reagent have been described in previous papers.1,2 LIX-64 is quite effective and selective for copper extractions although partially limited in pH ranges, losing extraction efficiency as the acidity of the feed solution increases to below pH 1.0. Also, the LIX-64 content in the kerosine carrier was limited to about 10 volume percent (except for special cases) because of rapidly decreasing phase disengagement rates above this content. This in turn led to large plant capital costs, as the organic flow rates had to be in- creased (rather than LIX-64 content) to extract the copper from high content liquors. This was true in all circuits where the feed copper content ran above 2.0 g/l copper. A reagent was needed which would extract copper from more acidic liquors (or higher copper content liquors) and which exhibited improved phase disengagement characteristics with reagent contents up to 30 volume percent. General Mills is pleased to announce the availability in commercial quantities of a new and improved reagent, L+-64~. This reagent broadens the pH range in which copper can be extracted, and exhibits superior phase disengagement characteristics. The improvement in the reagent has been noted in laboratory circuits, as well as pilot plant runs and commercial operations.

Jan 1, 1970

By Hiroyuki Tamaru, Futoshi Kusumoto, Kosuke Tanimura, Atsuyuki Kimura

"SUMMARY The Hachinoshiri tunnel is a 2,469 m long two-lane road tunnel on the Chubu-Odan Expressway. Since more than 70% of the total tunnel length consists of low strength rock masses the competence factor of which is less than 1.0, it is expected that a self standing span cannot be achievable because of no ground arch to be established. The tunnel was thus designed with tunnel support patterns forming multi-arc early ring closure that can develop the load-carrying capacity estimated from the exerted earth pressure, Po, which can result from the competence factor, cf. The tunnel support pattern was selected based on the competence factor at tunnel face, then the subsequent tunnel support patterns were determined with reference to the monitoring data. The tunnel construction adopted full-face excavation accompanied by early ring closure using a 330 kW road header. The proposed construction methods at this tunnel site have turned out ensuring tunnelling in massive squeezing rock, so that they can be verified as reasonable tunnelling technologies, clarifying the relationship between the characteristics of the mechanical behaviour of the tunnel and its design parameters. INTRODUCTION The presence of highly weathered mudstone having the competence factor less than 1.0 where the tunnel became unstable with the early ring closure having the distance to early ring closure, Lf, of 6 meters, resulting in difficulty in maintaining the inner section of the tunnel, prompted a substantial amount of high strength double support and replacing of the tunnel support (Sato et al., 2015). Based on the mechanical characteristics learned from the construction, the mechanical stability of multi-arc tunnels was investigated using 3D FDM analyses with respect to the ratio of the radius for early ring closure, r3/r1, and the distance to early ring closure, Lf, so that tunnel support patterns for early ring closure can be established in terms of the competence factor, of, which was employed for a 725 m long section. Consequently the tunnel support patterns for early ring closure which can be determined from the competence factor became applicable to tunnel construction. The relationship between the characteristics of the mechanical behaviour of the tunnel and its mechanical parameters was also clarified. The early ring closure method adopted ensured tunnelling in massive squeezing rock, verifying its effectiveness in stabilizing the tunnel."

Jan 1, 2016

By L. L. M. Kadnuck

The U. S. Bureau of Mines studied the suitability of using flexible tendon cable supports as secondary roof supports at a western coal mine. The supports were installed in longwall tailgate entries and grouted into the mine roof. This paper quantifies how the use of cable supports can improve ventilation in underground airways. A mine ventilation simulator was used to model the changes in airway resistance and airflow and show potential for further ventilation improvements when cable supports are used. Model results indicated that cable support use translated to savings in air pressure around the longwall panel and increased airflow at the longwall face.

Jan 1, 1994

By Harvey P. Knudsen

Case studies are presented in this paper to illustrate the usefulness and applicability of using conditional simulation in under- ground coal mine planning. Conditional simulation is a technique developed in the last five years that allows the building of a simulated ore body (or coal deposit) model. Construction and validation of the simulated model is described in order to show how well the model reproduces the essential characteristics of the deposit. In the model, the thickness, ash, and sulfur content are known everywhere in the deposit and each variable has the same mean, variance, and spatial variability (variogram) as that variable has in the real deposit. Use of the simulated deposit in the design of drilling strategy for long range mine planning is demonstrated in me case study. Determining the potential of short term production scheduling to reduce the fluctuations of sulfur in run of mine coal is described in the second case study.

Jan 1, 1980

By Thomas J. Wright

The evaluation and development of the Eastern North Carolina phosphate deposit resulted in one of the world's largest and most modern phosphate mines and fertilizer complexes at an investment in excess of $90,000,000. The resulting ore beneficiation process showed excellent correlation with pilot plant data. A number of variations from current industrial practices were introduced and projected from bench scale tests through pilot plant to production. Principal among these variations were the following: 1) removal of magnesium by classification, 2) simultaneous flotation of coarse and fine phosphate, 3) the use of saponified fatty acid, 4) utilization of filter wash water for deoiling, 5) utilization of a rougher concentrate for acidulation, 6) calcination of flotation concentrates, and 7) elimination of grinding prior to the manufacture of phosphoric acid.

Jan 1, 1971

By M. S. Klima

Tests were conducted to investigate the potential for recovering anthracite from preparation plant tailings. Samples were collected from tailings streams or slurry ponds of several anthracite cleaning plants. A washability analysis was conducted on each sample. The use of gravity-and surface-based cleaning processes for treating the 28x200 mesh tailings material was examined. Simulations were performed for various cyclone staging arrangements using published partition data for both water-only and dense-medium cyclones. Froth flotation testing was done on both precleaned anthracite and tailings material. Grade-yield curves were determined for various conditions.

Jan 1, 1995

By K. F. Unrug

The method of coal pillar design involves primarily two aspects, the geometry of the pillar and the strength of the coal. However, the strength of the coal has to be emphasized with respect to the entire pillar dimension rather than isolated strength values of coal samples taken and measured from different locations. The presently applied pillar design systems do not specify clearly what the coal sample strength really represents. The intention of this paper is to introduce the concept of seam strength as opposed to the current practice of using coal strength as a prime design criteria in the formulation of pillar calculations. Seams are most of ten composed of multiple layers of coal, partings, and bone in different configurations, changing within the vertical section of the seam even in relatively close locations. The difference in strength between the weakest and strongest component of the coal seam could be as much as five times or more. An experimental approach based on multiple compressive tests performed on coal samples from the Coalburg and the Warfield seams from Eastern Kentucky was undertaken. The analysis of the results lead to the conclusion that for pillar calculations both the weighted mean of the seam strength and the strength of the weakest stratum should be considered rather than the relatively vague aspect of coal strength The design of pillar dimensions based on the above mentioned aspects should assure a more realistic design performance.

Jan 1, 1985

By Thomas R. Mills

Under contract to the U. S. -Department of.-Interior, Office of Coal. Research, Hittman Associates recently completed a 16 month study of the environmental-factors associated with the siting, construction, and operation of large scale coal refineries. (1 2) The objective of this study was to identify the environmental effects and to define the magnitude of these effects and the approaches which can be used to mitigate adverse environmental consequences. In the study, the five major coal bearing regions of the country having reserves adequate to support a number of large scale coal refineries were considered. The regions considered were: Appalachian, Eastern Interior, Fort Union, Powder River, and Four Corners.

Jan 1, 1975

By R. A. Thomas, C. D. Litton

"The objective of this study was to develop a laboratory-scale method to rank the ignition and fire hazards of commonly used underground mine materials and to eliminate the need for expensive large-scale tests that are currently being used. A radiant panel apparatus was used to determine the relevant thermal characteristics of the materials: time to ignition, critical heat flux for ignition, heat of gasification, and mass loss rate. Three thermal parameters, TRP, TP1, and TP4, were derived from the data, then were developed and subsequently used to rank the combined ignition and fire hazards of the combustible materials from low hazard to high hazard. The results compared favorably with thermal and ignition hazards of similar materials reported in the literature and represent a simpler approach to quantifying these combustible hazards. INTRODUCTION The potential fire hazard from combustible mine materials is a major concern that can impact the safety of mine workers. Combustible materials tend to be solids and within this category there exist degrees of flammability and fire resistance. These materials may be readily ignitable or they may be able to withstand high temperatures and high heat fluxes. Presently, no simple methodology exists to assess these possible fire behaviors and quantify the resultant fire hazards. Thus, better knowledge of the thermal properties and chemical characteristics of combustible materials is of great importance to the safety of mine workers. Tewarson [1994] developed a methodology which he subsequently used to evaluate the ignition and fire resistant properties of combustible mine materials, but these efforts are more than 20 years old, and do not include many of the new materials used in mines today. The standard practice that has evolved for a combustible material to be approved by the Mine Safety and Health Administration for use in underground coal mines is to conduct extensive and costly large-scale experiments on each new material that is used in a particular mine operation. Results of such tests provide pass/fail answers to the questions of a material’s flammability or fire resistance, yet they provide little, if any, information that will lead to a better understanding of the basic mechanisms involved. Therefore, there is a need to quantify material flammability properties and to develop a methodology to rank the ignition and fire hazards of commonly used underground mine materials. During the heating and ignition stages of combustible materials, properties such as smolder susceptibility, minimum surface temperature for ignition, thermal conductivity, heat capacity, density, and heat of gasification are known to be important [Apte, 2006]. During the flaming stage, additional parameters, such as the heat of combustion, heat release rate, flame spread rate, yields of soot/smoke, and toxic gas production become more important as the flame is sustained and spreads. In very general terms, the heat flux incident on the surface of a solid combustible not only controls the rate of temperature increase of the local fuel surfaces, resulting in expulsion of fuel vapors that sustain the flaming process, but also the heating of other combustible surfaces that subsequently ignite and spread flame."

Jan 1, 2015

By John Murray, Ryan Smith, Daniel Ebin, Robert Gould, Thomas Hennings

The Atlanta Plane Train Tunnel West Extension was excavated at Hartsfield-Jackson Atlanta International Airport using Sequential Excavation Methods (SEM). At its shallowest point, tunnel cover to bottom of Domestic Terminal footings was limited to 6 feet in soft ground. To mitigate risk of excessive building movement due to tunneling-related activities, the columns near the alignment were directly underpinned. Underpinning was accomplished using a combination of grouted mini-piles, installed under low headroom conditions, that supported steel framing spanning over the tunnel excavations. This paper focuses on design and construction of the underpinning system used to mitigate risk from tunneling.

Jun 13, 2023

By Manoj Khandelwal, Bright Akuinor Tsidi, Newton Amegbey, Daniel Mireku-Gyimah

This study emphasizes the importance of understanding the factors that influence the throwing of flyrock in mining operations, a significant hazard to both workers and nearby structures. Moreover, it highlights how blasting engineers, when estimating flyrock occurrences and their travel distance, typically rely on input parameters such as powder factor (PF), hole length (HL), subdrill (SD), spacing (S), hole diameter (D), burden (B) and stemming length (ST), while overlooking crucial factors like velocity of detonation (VOD) and charge per bank cubic meter (CPBCM). Through analysis using support vector machine (SVM) modeling in MATLAB, the study underscores the impact of including or excluding VOD and CPBCM on flyrock throw distance.

Jul 1, 2024

By James E. Lonergan

To determine the best materials handling system for surface mined materials, one must develop a mine plan for each candidate system based on the most efficient use of that system. This is essential for a fair, unbiased economic compari¬son of the candidate systems. This paper will present two case studies where an integrated mine planning /systems engineering approach has been utilized at different levels of detail in the analysis of an in-pit crushing/conveying system vs. total truck haulage at 2 open-pit copper mines.

Jan 1, 1985

By Horry Parker Jr, Jason Gillespie, Justin Kolster, Stephen O’Connell

Construction of the 5,932-ft Reedy River Basin Sewer Tunnel in Greenville, SC was marked by a critical transition from drill-and-blast mining in mixed-face conditions to TBM excavation with limited rock coverage. In this paper, we discuss the geological, geotechnical, and risk management considerations for transitioning to TBM operations in variably weathered gneissic bedrock. After construction of an unexpected 230-ft starter tunnel due to differing site conditions, the 11-ft diameter TBM was successfully launched in December 2019 without significant ground support issues. This project highlights the effectiveness of extensive rock probing to fully characterize bedrock topography prior to the TBM launch.

Jun 13, 2021

By C. Vass, A. Noble

"The chemical treatment of mine-influenced waters is a longstanding environmental challenge for many coal operators, particularly in Central Appalachia. Mining conditions in this region present several unique obstacles to meeting NPDES effluent limits. Outlets are often located in remote areas with challenging terrain where conditions do not facilitate the implementation of large-scale commercial treatment systems. Furthermore, maintenance of these systems is often laborious, expensive, and time consuming. Many large mining complexes discharge water from numerous outlets, while using environmental technicians to assess the water quality and treatment regime multiple times per day. As an alternative solution, this paper describes the ongoing research and development of automated chemical treatment systems for mine water discharges. The current work explains the development of a bench-scale prototype that has been used to evaluate various monitoring, notification, and control strategies. Results from this testing are compared to present day practices to show the costs and benefits of implementing an automated treatment and monitoring program. INTRODUCTION Background The National Pollution Discharge Elimination System (NPDES), per Section 402 of the Clean Water Act, requires permitting of all point source discharges from coal mines. This program dictates that all water leaving a permitted boundary, whether it be process water or storm water, must leave through a monitored NPDES outlet. These permitted NPDES discharge points, also denoted outlets, outfalls or monitoring points, must meet a rigorous set of effluent limits to maintain compliance. Common effluent limits monitored by coal companies include but are not limited to iron, manganese, aluminum, total suspended solids (TSS), and pH. Raw mine water is often deficient in meeting these effluent limits, and as a result, various treatment processes are required to bring the water into compliance prior to environmental release. Depending on the mining and geologic conditions, water monitoring and treatment programs can constitute a significant operating cost for the mine operator. In Appalachia, acid mine drainage (AMD) constitutes one of the most significant and widespread water quality challenges that must be treated per NPDES guidelines. AMD is a general lowering of water pH that occurs when water and sulfide minerals interact within oxidizing conditions in coal and metal mining. Acid Rock Drainage (ARD) is a similar term that applies more generally to non-mining causes such as highway construction and other large-scale excavations. Today, mine influenced waters (MIW) is becoming more popular as the general term referring to all types of mining-induced water issues. AMD has been researched substantially over the last 30 years, with investigators studying various causal mechanisms and treatment strategies (e.g. Gazea, 1996; Ziemkiewicz, 1998; Skousen, 2000; Kleinmann, 2001; Johnson, 2003; Akcil, 2006; Kalin, 2006). This research has produced several pragmatic results, which provide numerous methods to predict, prevent, and treat AMD."

Jan 1, 2016

By James E. Myers

This study is a survey of the current "state-of-the-art" of commercially-available sonar tools to monitor the true shape of man-made cavities within the Hutchinson Salt of south-central Kansas. The work entailed ferreting out the available information, most of which is proprietary in nature; then examining actual existing conditions and arriving at a reasonable scientific evaluation of the method. Our studies were confined to one LPG field and two brine well operations in south-central Kansas. No field testing of any devices was performed, only questioning user firms, and studying cores, logs, and sonar surveys graciously made available by the companies we have contacted. Since these data are still somewhat proprietary, the company participants have asked that their company names be omitted from this presentation.

Jan 1, 1973

Little knowledge is available that considers the effects of continuous miner position on the possible respirable dust exposure of the remote mining machine operator. Such information could be very useful for increasing the awareness of the remote operator as to those parts of an extended cut that generate higher levels of respirable dust. This data could be used to develop guidelines for positioning the remote operator to reduce his potential exposure. This work details the effects of continuous miner position on dust levels measured on the machine and at the remote continuous miner operator location.

Jan 1, 1998

By R. E. Williams

University of Idaho scientists research under U.S. Bureau of Mines Cooperative Agreement C0278001 constitutes a complex hydrogeological, hydrochemical and metallurgical mine waste management project at an existing Superfund site. Technologies that may prove useful for the extraction of dissolved metals from acid mine water and solid wastes include lixiviation and biosorption. Acid mine water is the major, long-term problem in the valley. We are attempting to delineate the major sources of ground water recharge which feed the acid mine drainage and their hydraulic properties. Grouting of recharge areas may facilitate minimizing the production of acid mine drainage if recharge pathways can be identified.

Jan 1, 1990

By Gordon T. Clark

The preliminary design of four mined stations and 7.2 km (4.5 miles) of tunnels for Seattle’s light rail transit system is described. Constraints that influenced the design and options that were studied are discussed. The hilly post-glacial soft-ground geology of the Puget Sound Region pushed the alignment deep. Mined underground stations at depths up to 75 m (250 ft) and shafts with excavated diameters of 20-m (65-ft) are required. A 460 m (1,500 ft) sub-aqueous crossing of Portage Bay and undercrossing of an active 12-lane multi-level freeway were two of the more significant design constraints.

Jan 1, 2001

By Donald C. Violetta

During 1963 more than 200 million tons of coal was consumed by the public utility industry. Ash residual, from the burning of this coal has caused disposal problems. In order to prevent air pollution, dust collection systems have been installed to suppress the fine ash emitted from boilers before it is discharged into the atmosphere. The collected ash, called fly ash, must be removed from the dust collection facilities and disposed in some manner, usually at a substantial cost to the utility. Many years ago fly ash disposal was not a serious problem because the demand for power was relatively low and coarse coal was burned on stoker type traveling grate machines. The low burning rates utilized on these grates did not produce large quantities of air-borne coal ash while the mechanics of this system of burning resulted in a clinkered residue of cinders. Both of these conditions resulted in the production of only small quantities of fly ash. As the demand for electricity increased, a method of burning pulverized coal was developed and was introduced to the public utility industry in 1918 at Milwaukee, Wisconsin.1 This method of firing was considered a significant advance in steam electric generation as it (1) permitted the use of coals that could not be economically fired by other methods and (2) has generally resulted in improved efficiency, greater generating capacity and lower costs.2 The utilization of larger generating units using pulverized coal substantially increased the quantity of fly ash which resulted in a' more severe disposal problem.

Jan 1, 1966

By Erle I. Shobert

In the comparison and consideration of synthetic and natural materials, graphites represent a situation in which natural graphites amount to less than 10% of the total carbon and graphite production by weight, and less than 5% in dollar volume, There are few applications where it could not be re- placed by synthetic graphite. On the contrary, synthetic graphite materials can be engineered to cover an extremely wide range of applications. These include electrographite brushes for rotating machinery, pyrolytic graphite, graphite-impervious pipe, nuclear moderators, high purity spectrographic graphite, power tube anodes, graphite rotary shaft seals, and rocket nozzles. The special qualities of natural graphite and its limitations are delineated and the almost unlimited possibilities in artificial graphite materials are discussed.

Jan 1, 1964