Search Documents

By S. Hamm

Elevated total dissolved solids (TDS) content in waters downstream from surface coal mines in Central Appalachia is an increasing concern, as unnaturally high TDS and/or associated specific conductivity (SC) may contribute to deteriorated stream ecosystem health. The aim of this preliminary study was to explore the efficacy of accelerated leaching as a means of minimizing long-term TDS/SC generation by problematic overburden materials. Five spoil samples were collected and leached using simulated rainwater solutions under ambient and acidified pH conditions. SC and pH were monitored during each leach cycle, and ICP-MS was used to determine how leaching conditions affected release of specific ions. This paper highlights the results of both jar and column leaching tests. Among the most significant findings was that, for certain spoil materials, SC in leach column effluent was effectively reduced when spoil was leached first with acidic rainwater followed by ambient rainwater (vs. ambient rainwater leaching alone). This suggests that accelerated leaching might aid in long-term stabilization of some materials.

Feb 23, 2014

By M. U. Khan, A. D. S. Gillies

"Diesel exhaust is a major cause of large number of occupational diseases. Acute and continuous exposure to Diesel Particulate Matter (DPM) can cause numerous health issues including respiratory disease, reduced lung capacity, heart disease etc. The National Institute of Occupational Safety and Health (NIOSH) and the International Agency for Research on Cancer (IARC) consider diesel engine exhaust as carcinogenic. In large underground metal and nonmetal mining operations, regulatory compliance regarding miner’s exposure to airborne particles especially DPM is a big challenge. Complex mine networks add more difficulties in controlling DPM. MSHA relies on the NIOSH 5040 method for DPM compliance. The NIOSH 5040 method is a shift average based method which inherits some limitations. Due to these inherent limitations of the NIOSH 5040 method the concept of real-time DPM monitoring is promoted in the mining industry. Several real-time DPM monitors have been used by the researchers and efforts still continues to improve their measuring techniques and understanding. Real-time monitoring of DPM is vital to gain understanding of rapid changes in the mine atmosphere. The current study highlights the advancement in real-time DPM monitoring and mainly covers a review of several studies in which DPM concentrations were measured by utilizing real-time DPM monitors. INTRODUCTION Ventilation of underground mines is an important aspect of mining operations. Mining is a continuous activity and the ventilation networks in modern mines change with extended developments. Proper understanding of the ventilation network is a key design factor of an optimum mine ventilation plan. An important task of underground mine ventilation engineers is to provide clean air with sufficient quantity to the underground miners (Khan M. U. and Gillies A.D.S. 2015). The amount of fresh air supplied to the mine should be adequate to dilute the concentrations of contaminants present in the mine atmosphere. In the United States it is estimated that diesel powered equipment is used in thousands of mining operations (Stephenson D. J. et al. 2006). Use of diesel powered equipment is an attractive option in underground mines due to its several advantages over other available alternates. Diesel engines are rugged, dependable and fuel efficient (McKinnon 1999). It is common for diesel engines in heavy duty trucks to have a life of 1.6 million kilometers (McKinnon 1999). Looking at the developments in other energy alternatives, it can be assumed that the underground mining industry will maintain its reliance on diesel powered equipment (Anon 2001). DPM is an important source of mine air contamination in many non-gassy underground mines (Khan M. U. and Gillies A.D.S. 2015). Diesel exhaust is harmful for humans. Acute and continuous exposure to diesel exhaust concentrations can cause several health issues. Some of the health diseases caused by DPM exposure are respiratory diseases, reduced lung capacity, heart disease, and lung cancer (National Research Council. 1981, Mine Safety. 2005). In addition, NIOSH regards diesel exhaust as “potential carcinogen” (Centers for Disease Control 1988) and IARC has declared that “diesel engine exhaust is carcinogenic to humans” (IARC 2012). NIOSH has also declared that the reductions in DPM exposure would reduce cancer risks (Centers for Disease Control 1988)."

Jan 1, 2016

By R. Matusewicz

The key drivers for the copper smelting industry are a complex mix of economic and "human" factors which combine to drive technology in new directions and can provide a strong indication of future industry trends. Recent examples have been the drive to achieve increased scale of production and resultant cost efficiencies by using a single furnace high intensity smelting vessel, and the broad acceptance of Top Submerged Lancing (TSL) technology for this duty. The development and adoption of continuous converting processes to counter the increased pressures faced by the Peirce Smith converting process is another example of the need for innovation. This paper discusses the merits of the continuous converting process, describes how the Ausmelt TSL batch converting process has been adapted to the new Ausmelt Continuous Copper Converting (C3) process in response to these industry trends and examines the Ausmelt continuous converting flowsheet options available to the end user.

Jan 1, 2007

The overwhelming weight of scientific opinion indicates that human activity is having a discernible and negative influence on the earthÆs climate system. The Australian Government, together with about 100 other nations, has accepted the findings of the Intergovernmental Panel on Climate Change third assessment report, released in 2001. This report was prepared by several hundred eminent scientists from all over the world, from various scientific disciplines and with differing opinions on global warming. The IPCC third assessment report contains a series of relevant, significant conclusions; for example, it finds that there is an increasing body of observations that gives a collective picture of a warming world and other changes in the climate system. Global average surface temperature increased over the past 100 years by about 0.6¦C. This may not seem much, but in the 900 years beforehand, the EarthÆs temperature remained relatively stable. The 20th century was the warmest of the past 1000 years in the northern hemisphere (there is much better information available from the northern hemisphere than the southern hemisphere). The 1990s were the warmest decade of the millennium in the northern hemisphere and 1998 was the warmest year. Although many factors influenced the EarthÆs climate, scientists are confident that greenhouse gas increases were the main factor contributing to global warming in the last 50 years of the 20th century. Increases in carbon dioxide, methane, troposhperic (lower atmosphere) ozone, halocarbons and nitrous oxide have all contributed to global warming. Combating climate change cannot be done without the cooperation of industry and the community at large. It is important that Government and industry work together to achieve greenhouse gas abatement while ensuring continued economic growth. The cause of the problem û the generation of greenhouse gas emissions û lies at the heart of the structure and size of modern economic activity. Greenhouse gas emissions are embedded in our way of life from our energy consumption patterns to the basic production of food. Moreover, the costs of the impacts of climate change to the earth will be potentially revolutionary, not merely evolutionary. It is in this light, acknowledging both the seriousness and nature of the problem before us that I want to reflect on the key drivers in the international climate change negotiations. A consideration of the past, present and future from what I see as the mid-way point in the process. In 1997, Parties agreed to adopt the Kyoto Protocol, which sets out mandatory targets for greenhouse gas emissions for developed countries.

Jan 1, 2002

By Jun Li, Lingling Zhang, Daqiang Cang, Guizhou Zhao

Pilot trial of direct modification of molten blast furnace slag and production of high acidity coefficient slag wool fibers were investigated nearby a blast furnace. Molten blast furnace slag discharged from blast furnace and then directly flow into specialized modification furnace and quartz was simultaneously added into the molten slag as modification agent. The modified molten slag was electric heated to 1500–1550 °C and then the melt was produced into slag wool fibers through high-speed centrifugation method. Melt with acidity coefficient of 1.2, 1.4, 1.6 and 1.8 were investigated and fibers with corresponding acidity coefficient were produced. Slag wool fibers with shot content of 5.5, 5.8, 6.2, 6.8% and average diameter of 4.5, 4.9, 5.6, 6.4 lm for four samples were successfully produced, respectively. Total energy consumption and production costs decreased by 50–70% compared to traditional cupola furnace method. This method provides an energy-saving and emission-reduction technology for the direct utilization of molten blast furnace slag.

Mar 1, 2018

By Jacques B. Wertz

However excellent the geologic map of an area is, it can only show what is exposed on the ground. It cannot and should not generalize the information nor complete the picture by inference: this is left to the examiner. Consequently, it becomes justified for him to use all expressions of geologic structure in order to gain an additional dimension in geologic interpretation, and particularly so in mineral exploration. In previous studies related to Arizona, the known faults were the starting points and a host of interpolated, supporting geologic factors described in earlier publications ascertained the presence of a series of structural trends and lineaments found to be rather continuous and persistent, even though unsubstantiated by geologic maps. In present studies pertaining to the humid environment, with the same aim of seeking major structural trends and lineaments, the starting points are morphologic expressions such as straight lakes and straight segments of rivers, among others, because there generally is not enough geology available. An example is given herewith for an area that straddles the International Border, north of Spokane. In both semi-arid and humid environments, one observes that mineral deposits quite often occur close to the intersection of a major fracture or lineament with some secondary trend.

Jan 1, 1971

By Frank C. Stevens

The availability, cost and use of fuel and electricity for the cement industry is difficult to predict with a great degree of accuracy because the historical pattern of factors affecting energy was disrupted during the years 1972, 1973 and 1974. Forecasting is both an art and science and is based on .the premise that the best indicator of the future is the past. Statistical data is used to guide economists and businessmen in their predictions of the future. Even though the energy picture is changing, it is believed that electricity and fuel will be available for the cement industry in the foreseeable future, and this energy will be more costly in relation to the other items that are part of the manufacturing costs for portland cement.

Jan 1, 1977

By John F. MacDonald

This paper describes the driving of a 400 m long by 25 m diameter highway tunnel through sensitive, overconsolidated silts and clays. The design concept requires the construction of the permanent support system, consisting of 24 concrete filled perimeter drifts, before excavating the mass core. General construction procedures used during the construction of the perimeter drifts are described.

Jan 1, 1985

By B. Anameric

The pig iron nugget process is gaining in importance as an alternative to the traditional blast furnace. Throughout the process, self-reducing?fluxing dried greenballs composed of iron ore concentrate, reducing-carburizing agent (coal), flux (limestone) and binder (bentonite) are heat-treated. During the heat treatment, dried greenballs are first transformed into direct reduced iron (DRI), then to transition direct reduced iron (TDRI) and finally to pig iron nuggets. The furnace temperature and/or residence time and the corresponding levels of carburization, reduction and metallization dictate these transformations. This study involved the determination of threshold furnace temperatures and residence times for completion of all of the transformation reactions and pig iron nugget production. The experiments involved the heat treatment of self-reducing?fluxing dried greenballs at various furnace temperatures and residence times. The products of these heat treatments were identified by utilizing optical microscopy, apparent density and microhardness measurements.

Jan 1, 2007

By F. D. Ayhan

The aim of this study was to investigate the effects of various water mediums on desulfurization and deashing of a coal sample using flotation. For this purpose, experimental studies were conducted on a coal sample containing high ash and sulfur contents. The effects of pH, solid concentration, collector amount and frother amount on the flotation were investigated separately in Mediterranean Sea water, Çermik thermal spring water, snow water and tap water. Flotation results indicated that, when comparing the various water mediums, the following order for the ash content was obtained: snow water < Çermik thermal spring water < tap water < the Mediterranean Sea water. For the reduction of total sulfur, the following order was obtained: snow water > Çermik thermal spring water > Mediterranean Sea water > tap water. When snow water was used as a flotation medium, it was found that a concentrate containing 3.01% total sulfur and 27.64% ash with a total sulfur reduction of 57.06% was obtained from a feed containing 7.01% total sulfur and 41.17% ash.

Jan 1, 2009

By C. R. Summers, J. N. Murphy

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneurnaric drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115 -dbA s rope drill to approximately 100 dbA.

Jan 1, 1974

By Karel Van Acker

The automotive is a sector where energy consumption during the use phase prevails over the production and the end-of-life phase. Therefore, a lot of research and innovations at replacing classical steel parts by lighter materials like light metals and polymer composites. While composites are very attractive for the use phase of cars, their introduction suffers from the limited end-of-life options for composite structures. An extensive life cycle analysis for a reference car design has been conducted to study the effects of replacement of conventional steel structures by lightweight carbon fibre composite alternatives. The study also takes second order effects in the design of the car into account. The opportunities and treats of the trend towards more intensive use of carbon-fibre composites in car design are identified. A discussion on the potential of other types of composites for the automotive in terms of sustainability considerations is added.

Jan 1, 2010

By R. N. Gow

Acidic treatment of enargite (Cu3AsS4) dissolves both arsenic and copper from the mineral and then attempts to separate them in the leach solution. The reactivity of enargite was examined in acidic solutions, over the pH range 1-7, to determine a potential range for co-dissolution.. Enargite mineral samples from Butte, MT and Quirivilca, Peru were used as working electrodes in a cyclic voltammetry corrosion cell setup, which were then cycled multiple times over -1000 to 1000 mV. Surface reactions and transitions were characterized using in-situ Raman spectroscopy, which were then compared to updated predominance diagrams for the copper-arsenic-sulfur system from a previous study done under alkaline conditions. The region of co-dissolution is limited to > 600 mV vs. SHE and pH < 1 under the proposed diagram.

Feb 23, 2014

By G. M. Ritcey, K. E. Haque, S. H. Lucas

"Laboratory-scale hydrochloric acid leach tests were conducted on an Elliot Lake uranium ore. Hydrochloric acid leaches without an oxidant or with molecular oxygen (i.e., air or pure oxygen gas) as an oxidant favoured uranium and radium extractions. Conditions for maximum uranium, thorium and radium extractions with hydrochloric acid in the presence of sodium chlorate were determined. The highest extractions of uranium (96%), thorium (81%) and radium (91%) were obtained using a mixture of 44.0 kg HCI and 2.5 kg NaCIOJ per tonne of ore at 75°C with 18 hours &apos; retention.Flowsheets for two-stage leaching are proposed. The residues obtained from the second-stage leach contain uranium (0.002%), thorium (0.006%) and radium (15 to 20 pCi/g). Tailings of this nature are considered suitable for mine backfill, and, if pyrite is removed, suitable for surfacedisposal.IntroductionThe nuclear energy industry forecasts an increasing demand for uranium. This increasing demand requires not only largescale mining and processing of conventional and complex uranium ores, but also leads to the consideration of new and nonconventional sources of uranium, e.g., black shales, phosphate rocks, granite, sea water and fossil-fuel ash.Sulphuric acid leaching is the most widely used process to extract uranium from the ore(l). The leach liquor is separated from the solids (tailings), purified, concentrated in various intermediate stages, and finally a semi-purified product, yellow cake (80-85070 U30 8) , is precipitated. The tailings, which constitute nearly 98% of the total bulk of most ores, are usually discarded in surface disposal areas.The Elliot Lake region of Ontario is one of the major uranium producing areas in Canada. The principal uranium minerals are brannerite and uraninite, present as microscopic grains in the matrix of quartz-pebble conglomerates. The average grade is between 0.10 and 0.15% UPs. Up to 6.5% pyrite is also present in the conglomerates. Because pyrite is less reactive toward sulphuric acid leaching, almost all the pyrite goes into the tailings and eventually into&apos; the disposal sites."

Jan 1, 1980

By Laura McNally

In 2006, McNally International Inc., in a joint venture partner-ship with Aecon Constructors, was the successful bidder on two York Region Tunnel Projects: the Bathurst Collector/Langstaff Trunk Sewers and the York Durham Sewer System (YDSS) Interceptor Sewer 19th Avenue, both in the Toronto area. These projects comprised a total of 13 km (8 miles) of 2.74 m (9 ft) finished diameter tunnels and are both part of the YDSS. Both contracts required the use of earth pressure balance (EPB) tunnel boring machines (TBM) with a precast concrete segmental liner.

Jan 1, 2008

By L Q. Amorim

The mining district of the Quadrilátero Ferrífero (QF) in southeastern Brazil contributes to 70 per cent of the Brazilian iron ore production, which reached 370 Mt in 2010. Traditionally, four iron ore types were mined in the QF region:1. soft haematite,2. hard haematite,3. friable ‘itabirite’ (the Brazilian name for metamorphosed banded iron formation), and4. canga (an indurated iron-rich crust).With the exception of the hard haematite, these categories derive from supergene enrichment of the Paleoproterozoic Cauê Itabirite. High current iron ore demand means that the QF high grade supergene ores will be depleted in a few decades. Consequently, several mining projects are being developed to exploit unenriched, fresh itabirite. Among them, the Mineração Usiminas Serra Azul project in northwestern QF is one of the most advanced. Four major itabirite types occur in the QF region:1. siliceous (or standard),2. dolomitic,3. amphibolitic, and4. magnetitic.The dominant type in Serra Azul region is a fresh siliceous itabirite, composed essentially of haematite, martite and quartz that averages 36 per cent Fe (51.5 per cent Fe2O3) and 47 per cent SiO2. The second type, the magnetitic itabirite, consisting of magnetite, martite, gruneritecummingtonite, quartz, dolomite, stilpnomelane, and subordinate haematite, is typically a strongly magnetic greenish banded iron formation with the iron grade varying between 25 and 35 per cent. Chemically, it differs from the siliceous itabirite due to the relatively high CaO, MgO and, consequently, high LOI contents. Together with supergene ores, fresh itabirites have been included in the ore reserves of the Serra Azul project. We anticipate that all the four types of fresh itabirite will be incorporated as ore in the QF region, causing a huge increase on the iron ore resources of the district, and representing enormous environmental and technological challenges for the local iron ore industry.

Jul 11, 2011

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By B. Denby

Paper presented at a meeting on: Artificial intelligence in the minerals sector, held in Nottingham, UK, 20 April 1993. The design and scheduling of open pit operations are consistent problems encountered by the surface mining industry. Numerous techniques and algorithms have been developed to assist the mining engineer in the creation of optimum development strategies. Virtually all the practical techniques that have been produced have concentrated on one of the aspects (limit definition or scheduling) at the expense of the other. It has long been recognised, however, that the two activities are intrinsically linked and thus solving either problem independently of the other can only ever produce sub-optimal results as a whole. This has been termed the "circular reasoning problem". It has also been recognised that, for all practical-sized situations, solving both problems simultaneously is virtually impossible using conventional techniques due to the massive size of the search space involved. A technique is presented which is based on a self-learning genetic algorithm, which provides a combined pit limit and extraction schedule simultaneously in order to maximise the NPV (net present value) of the extraction. The theory is developed in two-dimensions and a number of examples of its application are presented. It is proposed that this approach is a highly efficient, heuristic technique offering the potential to transcend the circular reasoning difficulties of separate pit limit and extraction scheduling systems. Extension of the technique into three-dimensions and its application to realistic problem sizes are discussed

Apr 1, 1994

By Natesa I. Jayaraman

A field study was conducted by the Bureau of Mines to determine the feasibility and effectiveness of a secondary ventilation system retrofitted onto an Eickhoff EDW 340L double-drum shearer as a technique for controlling respirable dust generated during a longwall mining operation. An airflow duct was formed by enclosing the bottom of the undercarriage with steel plate and cutting air channels through the ends of the undercarriage frame. Air intakes were provided behind each cutting drum and at several locations along the undercarriage. Grills were installed at the intakes to prevent the broken coal from entering the ducting. A dust collector consisting of 5,000-ft3/min fan, water sprays, and a minicyclone panel was installed on the shearer at the tailgate end. Field results indicated that the secondary ventilation system reduced respirable dust more than 60% along the face. Reduction was less near the intake airway and when secondary dust sources occurred.

Jan 1, 1977

By Ethan Steward, Kyle Perry

Blast resistant structural design continues to be a research area of major concern for governments around the world due to explosive threats from both state and non-state actors. Glass and aluminum curtain wall systems are commonly used to clad the exterior of government and commercial structures, allowing light into the building, regulating the interior environment, and providing an aesthetically pleasing exterior. These systems are likely to fail when exposed to sudden, high-pressure events such as the purposeful or accidental detonation of explosives. Engineers have designed blast resistant curtain walls and structural elements to reduce the likelihood and severity of failure, but the design tools and testing mechanisms commonly used in the process may not accurately model or simulate actual blast conditions at all ranges. In blast resistant structural design, the origin of a shock wave is typically assumed to be in the far-field, creating a wave that is nearly planar and parallel to at least one face of the target. Shock is applied evenly and immediately across the entire impacted surface. However, the source of real-life blasts is often very close to the target structure, and the assumption of far-field planar shock does not always apply. Mid-field blasts exhibit qualities different from those assumed about far-field shocks, specifically a hemispherical shock that produces different peak pressures, impulse curves, oblique reflections, and Mach stems across a target. This paper will examine mid-field shock effects from scaled distances of 2.5 to 4 13 (6.3 to 10.1 13) on a tall, scaled target by measuring reflected and incident pressure, impulse, and shock velocity across the target. Results will be compared to theoretical blast parameter equations and empirical data used by the industry. Possible effects of mid-field blasts on structures and further research ideas will be suggested.

Jan 21, 2025