Search Documents

By McGuckin P. H

The Cadjebut orebody is a MississippiValleyType (MVT) zinc-lead deposit, and is located approximately 80 km southeast of Fitzroy Crossing in the Kimberley region of Western Australia. It is one of five zinc rich orebodies discovered by BHP Minerals in the region.The participation in the Cadjebut Joint Venture is BHP Minerals limited (Manager), 58 per cent and Billiton Australia Limited, 42 per cent.The mineralisation is contained in gently dipping dolomitised limestone sediments (part of the Lennard Shelf carbonate sequence) with an orebody width of between 60 and 120 m and a strike length of approximately 3 km. The deposit consists of two thin, stratabound shallow dipping orebodies, one overlying the other, to provide discrete but not independent mining areas. The orebody contains approximately 2.1 million tonnes of recoverable ore at an approximate grade of 12 per cent zinc and four per cent Lead.

Jan 1, 1992

By Renwick MT

Two innovative ground reinforcement products have been developed for use in the mining industry. One of these products is a high strength polyethylene (HOPE) bar for use as a rib bolt in underground coal mining and as a corrosion proof tendon in open pit mines. The other product is a cable bolt (Ultrastrand) which demonstrates enhanced load transfer and is available in continuous lengths. Ultrastrand's exceptional in- situ performance and versatility makes it ideal for mechanised installation in both underground and surface mining operations. Details of these products are presented and results from labortaory and field trials are discussed.

Jan 1, 1992

By H. Soto, J. Jara, F. Nava

"A combination of oxidation and precipitation was used to eliminate cyanide from gold milling effluents. Preliminary laboratory work developed with both synthetic cyanide solutions and with industrial effluents indicated that ozone can easily destroy free cyanide and weakly complexed cyanide (i.e. copper and zinc cyanide). In this case the reaction is quite fast and seems to be controlled by the mass transfer of ozone to the solution. Experimental results indicate that free cyanide and weak-acid dissociable cyanide in mill effluents can be reduced to less than 1 ppm. However, the iron-cyanide complexes proved to be quite resilient to destruction with ozone and they remained in the solution even after most of the free and weakly complexed cyanide was destroyed with ozone. These results were confirmed in a pilot trial developed at the Sphinx plant in northern Quebec.To deal with the problem presented by the presence of the iron complexes two different approaches were studied: use of a combination ozone-ultraviolet light oxidation, and the precipitation of iron-ferrocyanide complexes in the residual solution after ozonation. This last method proved quite promising since reduced the total cyanide levels of industrial solutions assaying as much as 250 ppm to less than 1 ppm of total cyanide. Control of the · pH of the solution was the key to obtain the precipitation of the iron complexes. The use of iron to precipitate cyanide complexes has the advantage of being less expensive and less toxic than copper (used by the Inco process)."

Jan 1, 1992

By Manca PP, Rossi G, Lipari D, Knissel W, Massacci G, Licheri P, Fioravanti E, Helms W, Lai S

Mining of the massive complex sulphides orebodies of Campo Pisano and San Benedetto (Southern Sardinia, Italy), dates back to before Christ, though their exploitation with modern technology was only resumed in the middle of the last century. The increasingly adverse economic conditions and the weakness of both country rock and mineralization were concurrent in forcing the Company's management to develop suitable high-productivity stoping methods. In the framework of a project fi- nanced in part by the Commission of the European Coranunities, and carried out in cooperation with the Universities of Cagliari (Italy) and Clausthal (Germany), a cemented backfill stoping method was developed. The concrete mix preparation and placement facil- ities, study of the cement mixes and endeavaa-s to optimize the methods are described. The monitoring system for measuring stress evolution within the emplaced backfill is illustrated together with the successful replacement of part of the Portland cement

Jan 1, 1992

By P. Massi

"Wholly owned by the Coniagas Mining Company, the oldest continuously listed mining company on the Toronto Stock Exchange, St. Andrew Goldfields is located on Hwy. 101 approximately 30 miles east of downtown Timmins, Ontario. Geographically situated on the Porcupine-Destor Fault, the mine and mill in Stock township is positioned in the heart of Northeastern Ontario's goldmining communities.In July 1988, a 600 ft. shaft, hoist, and compressors were already in place when construction started on a 500 T.P.D. capacity C.I.P. mill and crushing plant.By June 15, 1989 the mill was commissioned and attained the design capacity by August of that same year. Since then, changes to the circuit have increased throughput to 900 T.P.D. from two significantly different ore sources.Meeting the Ministry of the Environment's guidelines is an ongoing commitment utilizing the Inca S02 process in line between the tailings pond and secondary polishing pond.INTRODUCTIONExploration on what is now known as St Andrew Goldfields' Stock Township Mine was carried out ln the early l960 1 s by Hollinger Mines Ltd. The property was acquired by Quebec Sturgeon River Mines 1n 1973 and the main shaft was started ill 1979.When St Andrew Goldfields was incorporated 1n 1983, exploration and development commenced to identify the ore body. The company decided 1n 1987 to bring the Stock township property into production after an extensive feasibility study and testwork at Lakefield Research in Toronto. Leslie Engineering was contracted to design, engineer and procure al 1. equipment from the coarse ore bin to the tailings distribution system and backfill plant"

Jan 1, 1992

By Edmund J. Cardoza

The paper describes the design, construction and quality control aspects of the installation of a cement-bentonite (CB) cut off wall to impede seepage through a flood control dike. Special emphasis is placed upon the development of a proper specification, distinguishing the CB method from the Soil-Bentonite technique. The importance of the pre-construction laboratory testing program and field quality control procedures is emphasized by the fact that the in-place properties and characteristics of the CB cut off may not be known until after a majority of the work is complete. Sections are included which describe the construction method, the specialty equipment and personnel requirements and the quality control/quality assurance aspects of the project.

Jan 1, 1992

By Roy Woodall

Successful mineral exploration is the lifeblood of the mining industry. Contrary to what the environmental lobby would have the world believe, the industry is replacing the metals it is extracting. The reserve base has not changed significantly in 20 years (Fig. 1.) Mineral exploration is a research activity. First there is the idea, the vision or the intuitive thought. The experiments follow. These involve repeated phases of data gathering, data interpretation and concept testing through drilling. For many companies, exploration is the main investment in scientific research. Each mineral exploration experiment may involve years of costly work. Despite the improving tools of science and technology, the investment remains high-risk. Only the promise of high rewards, or desire to survive as a mining company, will stimulate the necessary commitment and level of investment. Confidence that an economic return can be achieved, confidence in the science and technology being applied and confidence in the people involved are the foundations upon which successful mineral exploration is built (Woodall, 1984). The challenges facing the explorationist in the 1990s fall into two categories: - the challenge to make the activity economic; and - the challenge to make the activity socially and, therefore, politically acceptable.

Jan 1, 1992

By K. Norris

"The Campbell mill has undergone numerous changes over the past 43 years. However the rate of change has increased significantly in the last 4 years. A new grinding circuit, carbon-in- pulp circuit, pressure oxidation plant, and column flotation circuit are all new additions. Other changes have occurred in the last 2 years including a large reduction in sodium cyanide consumption, and the introduction of a computer controlled grinding circuit. More improvements are planned in the next 2 years. Some of these improvements include the construction of an effluent treatment plant, and the replacement of filtering and Merrill-Crowe precipitation with carbon-in-leach and electrowinning.Recent changes and improvements to the Campbell mill are a commitment by Campbell mill personnel and Placer Dome Inc. to decrease operating costs, increase gold recovery and gold production, improve industrial hygiene and safety, and meet environmental compliance with current government legislation.INTRODUCTIONThe Campbell Mine has been and continues to be one of Canada's premier gold mines. Campbell Mine is 100% owned and operated by Placer Dome Incorporated. Milling of ore commenced in 1949 at a rate of 300 tons/day producing 58,000 ounces per year of gold. In 1992 Campbell Mine will mill 1340 tons/day of ore at a grade of 0.6 ounces/ton, producing 275,000 ounces of gold at a cash cost of $205.00 Cdn./ounce.This paper discusses some of the changes that have been made to the Campbell mill in the past 4 years. The flowsheet has undergone extensive changes and will continue to change rapidly in the next 2 to 3 years. A simplified flowsheet of the Campbell mill is shown in figure 1."

Jan 1, 1992

By Gillies A. D S, Just G. D

Coal washability data can be used for assessing coal quality. However, the techniques of using these data to solve quality problems differ from one mine to another and certain problems may never really be investigated due to limitations of the available techniques. One promising way to overcome these limitations is by correct application of geostatistics.A geostatistical study on coal washability data was undertaken based on a data set of closely spaced in-pit bore cores. These bore cores were analysed consistently over a relatively simple geological area. The average distance between the drill holes was about lOOm. There were 78 drill holes available for the area after deleting the erroneous bore cores. During the study, nine extra closely spaced drill holes were drilled within a single mining block.A procedure to construct two coal quality models, a kriging or cokriging model and a simulation model, was proposed. The modelling results for the data above are discussed and results of a mine scheduling exercise based on the models developed are included.

Jan 1, 1992

By Michael J. Friedel

As part of a study aimed at understanding the hydrology of in situ leach mining (ISLM), the Bureau of Mines, in cooperation with the Cyprus Casa Grande Corporation and the University of Arizona, is investigating dynamic transmissivity conditions during ISLM of a copper oxide ore deposit. Spatial and temporal variations in ore zone transmissivity during two years of ISLM operations at the Cyprus Casa Grande mine are evaluated during sixteen intervals of steady-state injection and recovery well operation. Direct inversion of an analytical hydrologic model is used to obtain estimates of transmissivity at 58 well locations during these intervals. Univariate statistical and geostatistical methods are used to describe the temporal and/or spatial relationships that exist between transmissivity and other ISLM parameters, including average well injection pressure, average sulfuric acid concentration in leach solution, and the relative configuration of injection and recovery wells. Average transmissivity during the sixteen steady-state time intervals varies between 6.00 x 10-6 m2/min. (6.46 x 10-5 ft2/min.) and 3.61 x 10-8 m2/ min. (3.89 x 10-7 ft2/min.). A trend toward decreas¬ing transmissivity is evident during two year of ISLM operations. This decreasing trend is found to correlate with a decreasing sulfuric acid concentration in injected leach solution, and suggests increasing geochemical precipitation within the deposit. Geostatistical analyses reveal a dynamic and anisotropic transmissivity structure within the target ore zone, that is dependent upon spatial and temporal changes in injection pressure and well configuration.

Jan 1, 1992

By John E. Wiegand

"We will attempt to explain the basic workings of a modern seismograph and how the recorded data can be interpreted, not only for determining compliance to the regulations, but also in determining whether or not a seismograph record is accurate and valid. We will discuss some parameters that should be included in all seismographic recordings. We will give examples and use overhead slidesto show examples of both accurate and valid recordings, and tampered and inaccurate seismograph recordings. Much of the information presented will be basic in nature, and will reflect the opinions and personal experiences of the author. We ho'pe the listener will gain valuable information concerning the use and interpretation of seismographic data, as well as find interest and sometimes humor in the examples shown."

Jan 1, 1992

By Russell C. Frith

This paper presents recent findings concerning longwall caving mechanisms relating to Australian mining conditions and their effect upon longwall support requirements and behaviour. The findings arc based on a program of intensive hydraulic support monitoring in a variety of Australian mining conditions coupled with geotechnical observations. Results from the study illustrate periodic weighting cycles of varying severity and these are related to the overlying geology in terms of the strength of individual strata units, their thickness and proximity to the longwall extraction. Several different caving mechanisms are identified which contribute to periodic weighting cycles. The importance of recognising weighting cycles in relation to the operation of the longwall face will be discussed in detail. Longwall support design methods are critically examined in relation to the case histories of the monitoring program. The applicability of the said design methods to Australian coal mining conditions is discussed and an outline of design considerations to facilitate productive longwalling is presented. Overall, the paper only "scratches the surface" of the work currently being undertaken by ACIRL in this area, and the findings of that work.

Jan 1, 1992

By R. N. Murarka

"Hydrocyclone modelling and selection procedure is illustrated. Computerized procedure for hydrocyclone cut size determination for grinding and non-grinding applications is described.A standard procedure for evaluating operating hydrocyclones is described in detail. Many case studies are illustrated comparing actual plant performance with the computer simulation output in terms of overflow product size distributions.INTRODUCTION Cyclones are widely used for applications such as: close circuit grinding, backfill, tailings and dewatering. Normally, cyclones are used for very fine separations where screens are not suitable or too expensive. Figure 1 shows the separation size range of various classifying devices. Cyclones are popular because of their low capital and operating cost. Cyclone selection procedure for different applications depends on the amount of information available on the cyclone feed slurry characteristics. Closed circuit grinding applications will be discussed in detail in this paper. The Cut Size:The size of the material in the feed which reports 50% to each product stream (i.e. underflow and overflow), after correcting for the feed solids by-passing with the underflow liquid, is termed the cut size or ""d50c"". This is often used as the criterion and the basis for cyclone design.When the corrected recovery to underflow of each mesh size in the feed is plotted against the geometric mean size in microns on a log scale, the micron size corresponding to 50% recovery is the d50c size."

Jan 1, 1992

By James S. Graham

Specifications for treated round wood piling are presented for the engineers consideration. Included in the text are background information, technical committees, Chellis, quality, treatment, static and dynamic stresses, accessories, and existing codes and standards. The specifications are also available using Word Perfect on 3.5 or 5.25 inch size disks provided by the National Timber Piling Council. Note: DFI recommended wording is wood, head, and toe, instead of timber, butt, and tip.

Jan 1, 1992

By Natarajan K. A.

During sulphide ore grinding, electrochemical interactions between grinding medium and the minerals play a significant role in bringing out enhanced ball wear on the one hand and alter the surface property of the ground minerals on the other. The role of the flotation reagents added simultaneously during grinding with respect to ball wear as well as flotation is yet to be established. Electrochemical measurements such as rest potential, combination potential and galvanic current between sulphide mineral and ball material couples have been carried out in the presence and absence of flotation reagents to understand the nature of electrochemical interactions between ball material and sulphide mineral. Electrochemical mechanisms and models have been proposed to explain the role played by the flotation reagents during different binary, ternary and quaternary interactions with respect to ball wear during grinding.

Jan 1, 1992

By Stephen Davies

Mining at Hudson Bay Mining & Smelting's Snow Lake Division is now in the mature stage of the mines' lives. These base metal copper-zinc mines have been operating for more than 30 years. Stopes had small pillars called "crown pillars" left between them. These pillars range up to 100 m (330 ft) long by 40 m (130 ft) wide and 15 m (50 ft) thick. Hudson Bay have been successful in removing these pillars by using cable slings, electric scoops, longhole mining and diesel load-haul-dump equipment. The different shapes and sizes of these pillars has required that many innovative techniques be tried in order to find acceptable economic mining methods. An overview of the different methods will be outlined. Background Hudson Bay Mining & Smelting's Snow Lake Division is located in Manitoba some 800 km (500 miles) north of Winnipeg and 200 km (125 miles) by road from the Hudson Bay smelter complex located in Flin Flon, Manitoba (Fig. I). There are currently three producing underground mines and one open pit operating at the Snow Lake Division, producing copper and zinc concentrates. Pillar recovery is intensive and vital to continued production of these mature mines. The crown pillars are producing more than 50% of the current mine production. This figure will increase in the future. The two mines at which crown pillar recovery is taking place and that will be discussed are the 400 t/d (440 stpd) Rod Mine and the 1000 t/d (1100 stpd) Stall Lake Mine, both five-day-a-week producers. Crown pillar mining has been applied for some time at these mines. However, it was only recently that the crown pillars became vital to production. This has necessitated a number of innovative techniques to recover them.

Jan 1, 1992

By D J. Holden

Prospectivity, the relative value of gold, investor confidence, general economic stability and legislation driven by public attitudes are seen as the major influences on the gold mining industry in New Zealand. Since the 1860s the gold mining industry in New Zealand has been subject to the complex interaction of these influences resulting in three successive boom and bust periods. The booms are related to periods of greatest potential economic growth. The busts are more strongly related to downturns in the economy and falling gold price. The influences may be expressed as trends over time. The role of gold has changed from being a currency base to that of a traded commodity. This change has caused price instability and rapid fluctuations in its value. Increased competing land uses, shifting public attitudes and legislative changes have added to the instability of the industry. Reaction against change is to be expected from the companies until new legislation is seen to be functioning efficiently. Other trends show that there has been a tendency towards reduced exploration and consolidation of active gold mining projects. The future consequences of this are likely to be felt both regionally and nationally as there will be no new discoveries to fill production voids which will develop as currently producing mines close. The review of New Zealand's resource use statutes is nearly complete. A period of legislative stability can now be expected. There are some positive signs that consents will be obtained much more quickly than under previous legislation, particularly by those companies which develop the skills to work with the system. The new regime is about consideration of impacts rather than specific activities. This, together with excellent prospectivity, bodes well for the identification of mineral resources in New Zealand.

Jan 1, 1992

By Lee Ann Gardner

This U.S. Bureau of Mines publication presents a case study of the processes used in permitting the Nome Offshore Placer Project, a gold mining project offshore Nome, Alaska which operated from 1985 through 1990. The mining project, developed by Western Gold Exploration and Mining Company, Limited Partnership (WestGold), used the BIMA, which was at the time the largest bucketline mining vessel in the world, to dredge gold from the ocean floor. This case study reviews the permitting process from the regulators' and industry's perspectives, as well as characterizing the efficiencies and inefficiencies associated with this case. The Federal, State and local laws applicable to the Nome Offshore Placer Project are identified, agency jurisdiction and interagency relationships are explored, and the chronology of the permitting process is examined. The regulatory authorities for both environmental monitoring and post-mining monitoring are delineated. Significant milestones affecting the project and required regulatory submittals are also included. The case study of the Nome Offshore Placer Project is detailed with respect to agency involvement and coordination, approaches to permitting from both the regulators' and developer's perspective, environmental issues, and permit stipulations which were unique to the project. The advantages and disadvantages of these topics are discussed.

Jan 1, 1992

By R. A. Bullivant

Roger Bullivant Piling Limited has started 1992 with the introduction of the CONE PILE into its range of precast concrete foundation techniques. Since the establishment of its Piling Division ten years ago, alongside the original Underpinning Company, a commitment to innovated development has seen a steady growth in Roger Bullivant's activity in piling, ground treatment and general foundation engineering. Over the last four years, £1.2 million has been invested by the Bullivant Piling Division into research and development in the field of precast piling and other foundation systems. The goal has been to develop economically attractive systems tailored to our clients design requirements and, wherever possible, unique to Roger Bullivant Piling.

Jan 1, 1992

By Das S. C

A detailed study was undertaken on the effect of Fe+3 in combination with LIX64N during copper electrowinning from sulphate electrolytes. The results show that the presence of Fe+3 not only affects the current efficiency during copper electrowinning but also affects the cathode quality. The effect is enhanced by electrolysis parameters like temperature, circulation rate, current density, etc. No significant effect was found from the presence of Fe+2. The presence of Fe+3 along with LIX64N causes a synergistic effect and results in a drastic fall in current efficiency. Moreover, cathode quality is also affected. A pyramidal structure is favoured in the presence of Fe+3 but the presence of LIX64N along with Fe+3 promotes a ridge structure. Addition of thiourea not only causes modification of cathode deposits, but also a rise in current Efficiency.

Jan 1, 1992