Search Documents

By G. A. Croes, N. Schwarz

The dimensionless groups, to which the variables that govern the displacement of oil from reservoirs by liquids can be combined, are derived. Three types of displacement are considered, viz. cold-water drive, hot-water drive and solvent injection. The derivation of the dimerzsionless groups is carried out by means of the relevant basic equations (in-spectional analysis). The resulting sets of groups are afterwards completed by means of dimensional analysis. The form of the groups is given in such a way that they can be adapted to suit the various boundary conditions that are encountered in practice. The physical meaning of the groups is discussed. They have all been brought together on a chart, from which their mutual relation and their corresporzdence to related dimensionless groups in common use in other engineering sciences can be read off. The limitations of dimensionally scaled model experiments as a useful tool for studying liquid flow in porous media, as occurring in oil reservoirs, are discussed. The use of models to study fluid mechanics has an appeal for everyone endowed with natural curiosity. What active boy has not played with ship and airplane models, or crude models of dam and drainage systems Even in the most advanced technical engineering, such models play a fundamental and indispensable role. "And yet in few departments of the physical sciences is there a wider gap between theory and practice, between scientific knowledge and the state of art, than in the use of models to study hydrodynamic phenomena." Garrett Birkhoff1 INTRODUCTION Laboratory displacement experiments are extensively used to investigate, directly or indirectly, the production behavior of petroleum reservoirs. Such experiments are representative of the reservoirs as a whole, if they are carried out with models that are "properly scaled." The performance of oil reservoirs is governed by the values of a number of variables, which can be combined to dimensionless groups. Two general methods are available for the derivation of these groups. In the first of these, dimensional analysis, combination of the variables is done essentially by trial and error. Its only premise is knowledge of the complete set of relevant variables. In the second method, inspectional analysis, the dimensional homogeneity of the equations describing the behavior of the system to be studied is used. The resulting dimensionless groups can be divided into: (a) independent (variable) groups, such as dimensionless length, time, etc.; (b) dependent groups, giving the dimensionless form of the variables, such as recovery and pressure, that can, at least in principle, be measured during an experiment; (c) similarity groups, which are independent constant groups, such as ratio of length to height of the reservoir and ratio of

Jan 1, 1957

By B. H. Caudle, B. M. Hickman, I. H. Silberberg

Secondary recovery projects often are not started in oil reservoirs until dictated by rising GOR's or declining oil production. Such circumstances require a well dispersed injection pattern to prevent the oil bank from bypassing the production wells. Many times this purpose is served by using the five-spot or line-drive patterns, in which half of the wells are made injection wells. A regular injection pattern is proposed that is based on the same well spacing as the five-spot but in which only a third of the wells need be converted to injection wells. Fluid flow model studies on this proposed pattern show that production histories will be as good as those for a five-spot pattern at mobility ratios of three and above. The model data are presented in a form that may be used to predict recoveries from both homogeneous and stratified formations. Introduction The injection of fluid into a petroleum reservoir usually is prompted by an actual, or predicted, loss in the productivity of the reservoir. Often, an oil reservoir is produced by pressure depletion until high GOR's dictate a change in policy. Fluid injection also causes increased ultimate recovery, but this usually is of less importance to the operator than is the maintenance of the production rate. It is a fact that the ultimate recovery in any particular fluid injection project is relatively independent of the number and spacing of the injection wells as long as the reservoir voidage through the production wells is balanced by the total injection rate. However, the response of a production well is directly affected by the distance it lies from an injection well. In places where the well productivities are declining, the injection wells should be spaced as evenly as possible among the producing wells ("dispersed" injection pattern). More particularly, if the production response depends upon the formation (and subsequent production) of an oil bank, each production well should be surrounded by injection wells. Otherwise, the oil productivity will increase very little as the oil bank moves past the well.'.' An evenly spaced injection pattern has the best chance of generating an oil kick in the production wells. If reservoir voidage and injection rates are to be equal, the ratio of injection wells to production wells must be equal to the ratio of the average injectivity to the average productivity (in reservoir volumes). This ratio is in strumental in choosing the injection pattern. Table 1 shows the production well to injection well ratio for the dispersed injection patterns that have been described in the literature.'-' All of these patterns will have comparable recoveries and response times (for the same basic distance between wells). The choice of pattern there fore depends upon the relative injectivity and productivity of the wells and upon the type of drilling pattern employed. Another important factor may be the ability of the proposed production wells to make up the lost productivity from those wells converted to injectors. These factors become more pronounced at the higher oil viscosities (low gravity oils). All other things being equal, the probable ratio of single well injectivity to single well productivity will be equal to the water-oil mobility ratio of the proposed flood. Thus, high mobility ratios (due to low gravity oil) should call for fewer injection wells — as long as these injection wells are "dispersed" to obtain more even pro duction response for the remaining wells. Secondary re covery projects in oil reservoirs seldom, if ever, will have mobility ratios requiring more injection wells than production wells. Thus, only the last five of the patterns listed in Table 1 will be of significant interest in oil recovery. Almost every development drilling program calls for the wells to be drilled along equally spaced rows and

Jan 1, 1969

By R. J. Wagner, G. H. Gronhovd, A. J. Wittmier

The paper describes the results of a series of full-scale boiler tests run to determine the ash fouling characteristics of a North Dakota lignite as a function of sodium content of the coal. Four levels of sodium were investigated and rate of fouling was determined both by boiler performance and by specially constructed probe equipment. Discussed is information on chemical and physical properties of the ash deposits. The vast lignite deposits in North Dakota are becoming increasingly important as a source of low-cost fuel for power generation. A new 200-megawatt lignite-burning plant located near Stanton, N.D., was placed in operation early in 1966. Another 172-mega-watt unit in the same area is scheduled for operation late in 1966, and plans have recently been announced for a 212-megawatt unit to be in operation by 1970. If these plants show good performance, western North Dakota could become a major power production center for a large geographic area in the upper midwest. One of the problems associated with the use of lignite in power boilers is its tendency to form troublesome ash deposits on boiler tube surfaces. This problem varies considerably from one lignite-fired boiler to another and is dependent upon such factors as source of lignite, boiler design, load factor, tube metal temperatures, and soot-blowing practices. This report presents data on sodium content* variation in a North Dakota mine, describes the results of a series of tests performed to determine the relationship between ash fouling tendencies and the sodium content, and tells how the mining company and electric utility have coordinated their operations to reduce the ash fouling problem. GENERAL BACKGROUND Until recent years it was generally assumed that North Dakota lignite from a given mine had qualities peculiar to that mine, but that within the mine, the lignite was quite uniform. In 1959, the Otter Tail Power Co. installed a 53.5-megawatt lignite-burning unit at its Hoot Lake plant, Fergus Falls, Minn. Shortly after the unit was put into operation, it was noted that at certain times under high load conditions, ash fouling problems were quite severe, but not consistent or predictable. Each time fouling occurred in the unit the position of the loading shovel at the mine was noted. Within two years it became apparent that there were certain areas in the Knife River Coal Mining Co. mine at Beulah, N.D., where the lignite apparently had a high fouling tendency for the Hoot Lake unit. Results from analyses of the coal did not show large differences in moisture percentage, ash percentage, heating value, or ash fusion temperature between the highly troublesome and less troublesome coals. After three years of operation, the troublesome areas had been quite well defined and the mining company started a procedure of bypassing these areas when load conditions at the plant were high and then returning to the troublesome areas to load the lignite during the summer months when peak loads were lower. It was noted that the lignite from the areas which caused severe fouling under high load conditions produced much less fouling at the lower summer loads. However, bypassing certain areas in the strip pit caused the mining company to disrupt their continuous loading schedule, which in turn upset their continuous stripping schedule and made for less efficient mining operation. Meanwhile, at the Hoot Lake plant, the number of soot blowers on No. 2 boiler had been increased from 30 to 55, and a very rigorous blowing schedule had been adopted resulting in soot blowers operating at least some part of 21 hrs per day. Fouling problems continued, with a resulting reduction in plant economy and reliability. During this period the Federal Bureau of Mines Coal Research Laboratory at Grand Forks, N.D., had initiated various research programs relating to the study of lignite ash and ash fouling problems. One project was a survey in which full seam samples were obtained from various locations in all the major

Jan 1, 1968

IRON AND STEEL COMMITTEE ALBERT SAUVEUR, Chairman. A. A. STEVENSON, Vice-Chairman. HERBERT M. BOYLSTON, Secretary, Abbot Bldg., Cambridge, Mass. John Birkinbine, William Kelly, J. S. Unger, William H. Blauvelt, Charles Kirchhoff, Felix A. Vogel, James Gayley, Richard Moldenke, Leonard Waldo, Henry D. Hibbard, Joseph W. Richards, William R. Walker, Henry M. Howe, C. F. W. Rys, William R. Webster, Robert W. Hunt, E. Gybbon Spilsbury, Frederick W. Wood. J. E. Johnson, Jr.,

Jan 1, 1914

Jan 1, 1932

By M. J. Marcinkowski, K. S. Sree Harsha

A detailed numerical analysis has been made of the equilibrium configuration of partial dislocations in a blocked deformation twin under an externally applied stress. Twins made up of both pure screw and pure edge partials have been considered. The components of stress in the vicinity of the twin tip associated with each of these configurations have been plotted. It has been found that at some critical degree of oblateness the shear stress fields of the blocked screw or edge twin can both sPontaneously nucleate slip, whereas only the component of stress oxx about the edge twin can nucleate and propagate cracks. TWINNING becomes a predominant mode of plastic deformation at low temperatures and/or high strain rates. Fig. l(a) shows what must be the first step in the formation of a deformation twin, namely the formation of a loop of imperfect dislocation bounding a stacking fault. In an fcc crystal the partial dislocations have Burgers vectors of the type 1/6 a,(112) and the fault is of the intrinsic type while in the bcc crystal the partials have Burgers vectors of the type ao(lll). The stacking sequence of (111) planes in a perfect fcc crystal is given by ABC ABC, and so forth, and in one which contains a twin by ABCABACBA, and so forth. It is apparent that the stacking fault and twin give rise to no mistakes associated with adjacent close-packed planes; however, with respect to second-neighbor close-packed planes the faulted crystal has twice as many mistakes as the twin. The energy of the twin boundary may thus be taken to be one-half that of the intrinsic fault boundary. In the case of the bcc crystal the stacking sequence of (112) planes is given by ABCDEFABCD, and so forth, in a perfect crystal, by ABCDCDEFA, and so forth, in a crystal which contains a fault, and by ABCDCBAF, and so forth, in one which contains a twin. An analysis similar to that applied in the fcc crystal shows that both the fault as well as the twin involve no neighbor violations across adjacent planes. However, there are twice as many violations across second-neighbor (112) planes associated with the fault as compared to that of the twin. Thus once again the energy of the twin boundary may be taken as one-half that of the fault. It is important to note that, unlike the fcc, the faults in the bcc crystal involve first nearest-neighbor violations and are thus expected to be of much higher energy than those in fcc crystals. A more detailed analysis of the material discussed above can be found in Ref. 1. To a good approximation then, the lenticular twin shown in Fig. l(b) can be generated by adding partial dislocation loops on successive (111) planes for fcc crystals or (112) planes for bcc crystals in the manner shown, with no additional expenditure of chemical energy other than that required for the fault shown in Fig. l(a). In practice, deformation twins are much more extended than that shown in Fig. l(b) and more closely resemble one shown schematically in Fig. l(c). It is readily apparent that the free energy of the twin and matrix are identical. In those cases where the partials lead to a structural change, the free energy of the material contained within the dislocation array is lower than that of the matrix and we have the so-called martensite transformation. The present investigation is the first in a series of five major theoretical-experimental efforts which will deal with the static and dynamic behavior of twin nucleation and growth. There has been a recent surge in activity pertaining to the equilibrium shapes of twin lamellae2'3 and

Jan 1, 1969

By Richard Moldenke

One of the little-known characteristics of cast iron, which nevertheless has an important bearing on results where accuracy in machining is essential, is the ability of this material to ease up internal strains when allowed to remain quiescent for a more or less extended period of time. It seems as if the molecules in such a casting, by virtueof their "mobility," can adjust their relative positions to an extent sufficient to overcome some of the existing stresses. The following instance will perhaps give a fair idea of the condition a casting may be in when just shaken out of the sand. A very large sheave-wheel, after shaking out, was taken outdoors to be cleaned and made ready for turning up. It was leaned against the side of the building, but before much could be done an arm tore apart with a loud report. Investigation showed that the sun had been shining on the upper rim, thus adding a slight strain to those already existing within the arm and thus overbalancing the strength of the metal in tension. Had this sheave been kept under cover for a while, or at least until machined, the strains would have eased off sufficiently to allow the sun to look upon it without disaster. It will not be necessary to multiply examples. Every engineer knows the danger of water-hammer in pipe lines, particularly if the latter are of cast iron. Every mechanic knows, or should know, that it is not good to strike a fitting that is under steam pressure. It will be necessary to say a few words on the "internal strains" in castings—the so-called "casting strains" we hear so much about. We all know that to get a casting reasonably true to the dimensions wanted requires a slightly larger pattern. The usual allowance for gray iron is 1/8 in. to the foot (1 cm. per meter) and 1/4 in. to the foot (2 cm. per meter) for white iron (all dimensions). This reduction in length, breadth and thickness in a casting is erroneously called "shrinkage." It should be called "contraction," as for practical purposes it is simply the difference in dimensions of the casting red-hot and cold. The real "shrinkage" covers an entirely different situation. When a

Jan 1, 1917

By H. M. Chance

Recent research work has shown that coal can be produced, at reasonable cost, from almost all coal-mining districts containing not more than 3 to 8 per cent. of ash. From coal so produced, an abundant supply of coke, suitable for blast-furnace operation, can be made containing from 12 down to 6 per cent. or less of ash. These statements apply broadly to the Appalachian coal belt, including most of the mining districts in Pennsylvania, Ohio, West Virginia, Kentucky, Tennessee, and Alabama. The exceptions will generally be found among those coals carrying a prohibitive percentage of sulfur. Any gravimetric heavy fluid method of separation will effect a reduction in the percentage of sulfur, but this reduction may not be sufficient to produce, from coal unfit for metallurgic use, a product that can be so used. When a large part of the sulfur is in the form known as "organic sulfur, "or is present as very finely disseminated and homogeneously distributed pyrite, possibly it cannot be eliminated from the low-ash coal produced. When the sulfur exists as pyrite in distinct layers, bands, or nodules, or when it is finely disseminated but is irregularly distributed, often a low-ash coal low enough in sulfur to make good metallurgic coke can be produced from relatively impure coals. It has generally been assumed that the quality of coke on which blast furnaces must be operated depends on the geographic location of the furnace, and that the grade of coke on which a blast furnace must operate is that produced from the best coal obtainable by careful mining; or if the coal is prepared by washing, hand picking, or other means by which the foreign impurities are removed, that the grade of coke on which the furnace must operate depends on what has been termed the "inherent ash" of the particular coal. The term "inherent ash " is generally understood to mean the percentage of ash present after all removable (free) impurities, slate, fireclay, high-ash bony coal, and pyrite have been removed, and is usually applied to the percentage of ash present in run-of-mine coal from any mine after these impurities have been removed. Perfect washing, or perfect preparation, is understood to be attained when the percentage of ash in the washed coal is reduced to the percentage of inherent ash; that is, of ash that cannot be removed by the washing processes in common use. Wash-

Jan 1, 1924

By C. van Dijk

In Sept., 1960, a steam-drive project was started in the solution-gas drive area of the Schoonebeek field. A part(ern of three five-spots and one four-spot was selected covering an area of 65 acres. The pay in the project area has good lateral continuity and dips slightly to the northeut; it is about SO ft thick and permeability increases from 1,000 and at the bottom to approximately 10,000 md at the top. The oil originally in place was 12.6 X 10' bbl. The oil has an in situ viscosity of about 180 cp. At the start of the steam drive the cumulative primary production due to. solution-ga.7 drive amounted id 4 Percent of the oil originally in place. Reservoir pressure had dropped about 120 psi and no significant primary re-.serves remained. Some 11.3 million bbl of steam (all steam quantities are expressed in barrels of water vaporized) have been injected, resulting in production of an additional 4.1 X I0 9bl of oil, or 33 percent of the oil originally in place. This corresponds to a cumulative oil-stearn rario of 0.37 bbllbbl. It appears that the steam preferentially moves r updip while liquids are produced mainly from downdip wells observations indicate that tile steam flows through only the upper part of the formation. The lateral steam distribution in the pattern is satisfacrory since several prodriction wells hardly reacted and, hence, cori tributcd little to the oil production. Production performance and results from material balance calcutlations agree satisfactorily with the results of large-,scale laboratory experiments. On the basis of these experirmental results the .steam drive, together with a cold water follow-up. is expected to bring ultimate recovery to a value of crt leas: 50 percent of the oil originally in place. No serious production problems have been encountered. However, due to mechanical fuilure, two old prodriction wells and one injection well had to be replaced. An extension of the. steam drive in this area is under connstruction. Introduction The Schoonebeek oil field, discovered in 1943 and developed after World War 11, is situated in the eastern part of the Netherlands. The main oil reservoir in this field is the Valanginian sand. A completely sealing fault divides this reservoir into two areas (Fig. 1): the southwestern part of the sand body where primary production is ob- tained by means of a solution-gas drive, and the remain. der where edge-water drive is the production mechanism. In the greater part of the field the reservoir consists of a single, unconsolidated sand body. The net thickness ranges from 30 to 100 ft and the top is between 2,400 and 2,800 ft below sea level. Formation permeability varies from approximately 10,000 md at the top to values of the order of 1,000 md at the bottom, and porosity is about 30 percent. The reservoir contains a paraffinic oil of 25" API gravity with an in situ viscosity of 160 to 180 cp. Initial oil saturation was high (85 to 90 percent). The relatively large quantity of oil in place (more than 10' bbl), and the low ultimate primary recoveries expected from this field — approximately 15 percent stock-tank oil initially in place (STOIIP) for the water-drive area and 5 percent STOIIP for the solution-gas drive area — clearly indicate ample scope for secondary recovery. Because ies-ervoir and crude characteristics made this field suitable for thermal secondary recovery, a hot-water drive project was started in the water-drive area about 10 years ago. A few years later a steam drive and an in situ combustion project were started in the solution-gas drive area. This paper deals with the performance of the steam-drive project, which was started in Sept., 1960, and which is still in operation. Design of Steam-Drive Project, An experimental investigation of the steam-drive process carried out by schenk in 19561 indicated that under schoonebeek conditions steam injection could be an attractive secondary recovery method. the findings and encouraging results of a pilot test in the Mene Grande field in venezuela,i led to the design of a steam-drive project in the schoonebeek field, Pruject Site and Pattern In 1958 the reservoir pressure in the solution-gas drive area had decreased to about 120 psi, and oil production rates of wells in this area had dropped to 7 to 10 B/D. The cumulative primary production was about 4 percent STOIIP, leaving an oil saturation of approximately 85 percent. In view of the large amount of oil left behind in the reservoir, the solution-gas drive area was selected for the planned steam-drive project. The area in the vicinity of Well S1 3 (Fig. 2) was considered to be suitable since it is at least partly isolated from the rest of the field by faults and the sand is relatively thick (about 80 ft).

Jan 1, 1969

William Kent, New York City: I regard the paper of Professors Lord and Haas as the most important and valuable that has yet appeared on the subject of the calorific value of American coals. The close correspondence of the results they have obtained by the use of the bomb calorimeter with those calculated by the Dulong formula from the ultimate analyses, confirming the work done by Mahler in France some years before, is evidence of the extreme accuracy of their work, and gives us renewed confidence in Mahler's modification of the Berthelot calorimeter, and in Dulong's formula, which latter, until

Jan 1, 1898

By W. S. Gatley, F. C. Appl

This paper presents a combined analytical and experimental study of chisel penetration vs time during chisel impact on rock, a problem of fundamental importance in improving the performance of roller-cone bits or percussion drilling toots. For a given force-time relationship between chisel and rock, the problem of determining the penetration (displacement) vs time of the chisel is formidable. This is so because the rock is a nonlinear system with distributed mass and distributed damping (friction, dissipation of energy due to rupture, etc.). Since the literature does not contain adaptable solutions, the rock behavior to impact was simulated approximately by an "equivalent" lumped system, that is, an "equivalent" mass, spring, dashpot system. With this assumption, an analytical solution was found for chisel penetration vs time due to a sinusoidal load between chisel and rock. From this solution were found curves, in terms of dimension-less variables, for the maximum depth of penetration vs the frequency of the sinusoidal loading and for the energy transfer vs frequency. The results of this analysis were used to predict the penetration rate of rotary rock bits us rotary speed. The curve indicated that an optimum speed exists. To verify this analysis, an experimental apparatus was constructed and used to apply a sinusoidal pulse to a chisel penetrating a rock specimen under atmospheric conditions. Strain gauges were mounted on the chisel shank and a velocity transducer was mounted between the chisel and the rock surface. The velocity was integrated electrically and picked up simultaneously with the strain gauge signal on an oscilloscope. Permanent records were made photographically to provide simultaneous records of force us time and penetration us time. In comparing the experimental results for limestone and dolomite with the theoretical results, good agreement was found in the frequency range of the experiments. Unfortunately, the inertia effect (peak penetration) indicated by the theory occurs at a frequency much higher than could be obtained experimentally with the apparatus constructed. A "rate-of-loading" effect is indicated theoretically, but has not yet been verified experimentally. INTRODUCTION The process of drilling with percussion tools or rotary rock bits is basically related to the transient response of rock to surface impact. Each time a bit tooth contacts the rock, high stresses are developed which result in penetration and rock removal. As the tooth moves on, stresses are relieved and a new cycle begins as the next tooth contacts the rock. Thus the drilling process, which consists of an endless succession of these cycles, can be studied in terms of a single cycle. It is apparent, therefore, that the study of single-chisel impact on rock is fundamentally important in improving the performance of roller-cone and percussive-type drills. Previous studies in this area have been conducted by Simon1 and Hartman2 by means of drop tests. In these tests a chisel was attached to a weight and allowed to fall, due to the force of gravity, so that the chisel was driven into a rock specimen upon impact. Strain gauges were attached to the chisel shank and the resulting force-vs-time curves were recorded photographically from an oscilloscope screen. The depth of penetration and crater dimensions were also measured. These tests have provided much valuable information but, as mentioned by the investigators, have not provided complete information on the effect of "rate of loading'! This is partly due to the fact that the chisel motion during drop tests is not a controlled motion which can be varied in form and frequency. Therefore, it seemed that additional information could be obtained by studying chisel impact under conditions where both the motion and the frequency of loading could be controlled. This paper presents a combined analytical and exper-

By Francis Lucas

EACH year we gather in this auditorium to honor the memory of a. distinguished American metallurgist and educator. I cannot bring to you reminiscences of Prof. Henry Marion Howe as other lecturers have done. It was not my good fortune to enjoy the-privilege of studying and working under his direction. As I have reflected on the published works of Professor Howe, it has seemed to me that his mind was trained on the nature of metals and on the mechanism which produced known but unexplained effects. He was interested in controlling and regulating the causes so as to produce specific effects, useful in serving mankind. I recall an afternoon in May, 1925, when, at the invitation of Mrs. Howe, I visited his former home, Green Peace at Bedford Hills, N. Y. The purpose of my visit was to receive at the hands of the widow an engraving of Professor Howe, a reproduction of a painting from life. Mrs. Howe showed me his study. The walls of this large attractive room, brilliantly illuminated by the spring sunshine, were literally covered with the scrolls of honors and of decorations which had been conferred on Professor Howe by governments, academies, universities, societies and institutions the world over. As we walked about the room, she pointed out the significance of each honor and recited a few details of each occasion. I sensed the pride with which Mrs. Howe, then in the late autumn of her life, told me of her husbands' achievements, of his struggles, of his disappointments and of his successes. There was a surprisingly familiar note in the recital to which I was listening. I 'have found the same theme running as a disconnected thread through the written accounts of the lives of most men of science. We then went to the drawing room to chat for a few minutes before I said my farewells. As we seated ourselves, Mrs. Howe turned to me and asked: "Mr. Lucas, what of this great microscope of yours? Cannot it be applied to the study of disease? What a great blessing it would be if it could be directed to relieve the suffering of mankind."

Jan 1, 1931

The problems associated with the processing of the Tilden ore are very much representative of the problems encountered in plants processing fine grained magnetic and nonmagnetic iron ores. I would like to comment on some of the problems mentioned in Dr. Nummela'spaper and add to his list of research opportunities in the processing of iron ores. Grinding, the most important step in the processing of fine grained iron ores, is synonymous with liberation. One grinds to separate discrete grains of minerals from the gangue. By convention- al grinding in tumbling mills, mostly random size reduction is achieved with relatively little preferential liberation of minerals. Not only are discrete particles broken that should not be broken, but damage is done to the mineral surfaces. The combination of over- grinding and surface damage shows up in lower recovery figures and higher grinding costs. What is obviously needed is a better comminution process that is more discriminating and that would permit liberating mineral particles at the coarsest possible size with a minimum production of fines. Laboratory attempts at such preferential grinding have been quite successful, but technological difficulties have unfortunately prevented its use. Impact grinding is a good example of a new comminution process that has not been accepted because of equipment problems. Either these problems have to be solved or new comminution systems have to be developed to reduce grinding costs and improve liberation. In his paper Dr. Nummela mentions the change in the primary mill throughput that occurs during the winter months. Seasonal changes in the operation of the grinding circuit and other unit operations have been observed in many plants, and many explanations for this phenomenon have been advanced. The fact is that we do not fully

Jan 1, 1979

By Eckley B. Coxe

AT the first meeting of the Institute, a paper was read by Mr. Rothwell, calling attention to the importance of at once considering the great waste of anthracite coal under the present system of mining and preparing that fuel for market, and a committee was appointed to examine and report upon the method now in use. About the time the committee were selected, a general resumption of work, after the long strike, took place in the coal regions, and the members of the committee have not in consequence had as much leisure to devote to the study of the question as its importance de¬mands. In the present preliminary report we shall merely sketch out the plan which we propose to pursue in our investigations, so that when our fellow-members are called upon to assist us in our work by fur¬nishing statistics, etc., they may understand more clearly for what object our inquiries will be made. As one of the most practicable methods of obtaining the informa¬tion requisite for an intelligent consideration of our subject, we pro¬pose to send, from time to time, to members and others interested in the mining of anthracite coal, printed sets of questions relating to points under consideration. We would here impress upon our fellow¬-members the importance of filling up these papers as far as they can from their own knowledge. We would, of course, wish each ques¬tion to be answered as fully as possible, but we do not expect every one to answer them all. One question well answered would be of more use to us than the whole paper filled up with answers, many of

Jan 1, 1873

By Eckley B. Coxe

At the first meeting of the Institute, a paper was read by Mr. Rothwell, calling attention to the importance of at once considering the great waste of anthracite coal under the present system of mining and preparing that fuel for market, and a committee was appointed to examine and report upon the method now in use. About the time the committee were selected, a general resumption of work, after the long strike, took place in the coal regions, and the members of the committee have not in consequence had as much leisure to devote to the study of the question as its importance demands. In the present preliminary report we shall merely sketch out the . plan which we propose to pursue in our investigations, so that when our fellow-members are called upon to assist us in our work by furnishing statistics, etc., they may understand more clearly for what object our inquiries will be made. As one of the most practicable methods of obtaining the information requisite for an intelligent consideration of our subject, we propose to send, from time to time, to members and others interested in the mining of anthracite coal, printed sets of questions relating to points under consideration. We would here impress upon our fellow members the importance of filling up these papers as far as they can from their own knowledge. We would, of course, wish each question to be answered as fully as possible, but we do not expect every one to answer them all. One question well answered would be of more use to us than the whole paper filled up with answers, many of

By G. T. Brookman, P. B. Katz, D. K. Martin, J. A. Ripp

With the increasing emphasis on using American fossil fuel resources, more facilities are evaluating coal conversion. In addition, those facilities now using coal are considering better coal storage procedures to minimize negative environmental impacts. For example, rainfall and snowmelt on a coal pile produce a drainage stream high in acidity, suspended and dissolved solids, iron, sulfate, and trace metals. Usually, the characteristics of the runoff stream do not allow for direct discharge to streams and lakes. Detention in a holding pond and pH adjustment are traditional methods of treating coal pile runoff before discharge. Historically, this treatment methodology has been performed inefficiently without a good data base to assess how much runoff treatment is needed to meet effluent guidelines. A model was developed to simulate runoff volume and pollutant loadings under different rainfall conditions. This model will be used to size and design treatment works for coal pile drainage. The Ohio State University (OSU) version of the Stanford watershed model was selected as the base model. The OSU model simulates overland runoff in a rural area. It includes factors such as soil moisture, depression storage, infiltration, and flow to a ground water reservoir. TRC also used the OSU co-model for acid production in coal refuse piles as the basis for qualitative modeling work. A number of modifications were made to the OSU models to make them applicable to coal storage piles. The physical/chemical reactions included in the models are described in more detail in the project report. In addition, the models were altered so that a standard NOAA magnetic tape of historical meteorological data can be used as data input instead of requiring the user to create a data file. The resulting TRC coal pile drainage model is actually two models - a quantitative model, termed H2OTRC, and a qualitative model, TRCCOAL.

Jan 1, 1984

By H. M. Rutherford

THE reflection method in seismic prospecting has aroused much interest in the past few years. The purpose of the present paper is .to present the method of reflections in the mapping of geologic structure and also to give some indication of its limitations. The reflection method is well adapted to the mapping of geologic structure in the Mid-Continent fields, and has been found most useful there. The refraction method is ideally suited to the finding of structures, such as domes, where the amount of relief is very large. This explains the brilliant success of the refraction method in the Gulf Coastal region of Texas and Louisiana. The additional fact that salt has a much higher velocity than the sur-rounding sediments made their discovery much easier. By the use of the reflection method, differences of relief of 25 to 50 ft. to the mile may be detected at a depth of 5000 ft., and the depth points accurately plotted on a map. This is hardly possible by the use of the refraction method. The reflection method has been in almost continuous use in the Mid-Continent area since 1926, but very little, if anything, has been published until recently(7) ? regarding either the method or the results. The dis-covery of several oil fields is now attributed to the use of the reflec-tion method. Reflection methods have been used by the Germans to find the thick-ness of the ice of several glaciers. (2,8) The depths there considered were of the order of only a few hundred feet. For the method to be of any practical value in this country, it must be able to work to depths of several thousand feet. As was indicated above, this is now possible, though there are many problems connected with the reflection method yet to be solved. The refraction method requires that the shooting be done over long ranges. It was necessary, for example, to take distances out to several miles in order to penetrate some five thousand feet. Naturally this uses a good deal of dynamite. In the reflection method the distances are much shorter and the amounts of dynamite are much smaller, within limits which will be noted below. The chief distinction between refrac-tion and reflection methods is to be found in the analysis of the seismo-gram. Refraction shooting makes use of only the first arrival of energy

Jan 1, 1932

By Roger M. Nendick

The recovery of precious metals from heap leach solutions can be accomplished by two processes: 1. The Carbon Adsorption Process 2. The Merrill-Crowe Zinc Precipitation Process A brief review of the relative process economics is made. Each process presents certain design considerations that must be addressed during the evaluation and engineering design for the project. Discussion is presented on the design criteria for each process.

Jan 1, 1984

By Joshua E. Clayton

THIS remarkable gold and silver bearing district is situated on the middle fork of Boise River, in Alturas County, Idaho Territory, about eighteen miles north of Rocky Bar, and sixty-five to seventy miles, as the crow flies, east of Boise City, the capital of the Territory. This district lies in the very heart of one of the most wild and mountainous regions of Idaho. For many miles in every direction nothing can be seen but bold granite mountains, with deep narrow gorges cutting into their sides in every direction, rendering them almost inaccessible except to the hardy mountaineer and adventurous prospector. The mountain sides are covered, in most part, by dense forests of pine, fir, and spruce timber. In every canon there are clear streams of pure running water that empty into the principal forks of Boise River. The only line of approach to this mountainous region at present is from the southwest, by way of Rocky Bar, the county seat of Alturas County, to which place there is a good wagon-road. From thence to Atlanta City, eighteen miles, the road, or pack-trail, passes over the high, steep range that separates the south and middle forks of Boise River. During severe winters this line of approach is closed up by deep snows for months at a time, thus leaving the district isolated, in the bosom of the grand old mountains. The geological formation is granite, of a coarse, friable texture, and in many places is traversed by numerous dikes of syenite, and three or four varieties of porphyry, which cut through the granite in easterly and westerly directions. The metal-bearing veins also have an easterly and westerly trend, but are occasionally intersected by the dikes. The largest number of the gold and silver lodes are confined to a

Jan 1, 1877

By Joshua E. Clayton

This remarkable gold and silver bearing district is situated on the middle fork of Boise River, in Alturas County, Idaho Territory, about eighteen miles north of Rocky Bar, and sixty-five to seventy miles, as the crow flies, east of Boise City, the capital of the Territory. This district lies in the very heart of one of the most wild and mountainous regions of Idaho. For many miles in every direction nothing can be seen but bold granite mountains, with deep narrow gorges cutting into their sides in every direction, rendering them almost inaccessible except to .the hardy mountaineer and adventurous prospector. The mountain sides are covered, in most part, by dense forests of pine, fir, and spruce timber. In every canon there are clear streams of pure running water that empty into the principal forks of Boise River. The only line of approach to this mountainous region at present is from the southwest, by way of Rocky Bar, the county seat of Alturas County, to which place there is a good wagon-road. From thence to Atlanta City, eighteen miles, the road, or pack-trail, passes over the high, steep range that separates the south and middle forks of Boise River. During severe winters this line of approach is closed up by deep snows for months at a time, thus leaving the district isolated, in the bosom of the grand old mountains. The geological formation is granite, of a coarse, friable texture, and in many places is traversed by numerous dikes of syenite, and three or four varieties of porphyry, which cut through the granite in easterly and westerly directions. The metal-bearing reins also have an easterly and westerly trend, bat are occasionally intersected by the dikes. The largest number of the gold and silver lodes are confined to a