Search Documents

By L. C. Noakes

Despite a long history of mining. Australia had no Commonwealth organization dealing specifically with the mineral industry until 1946, when the Australian Bureau of Mineral Resources, Geology and Geophysics was established. Once formed, this new organization quickly expanded to include a Mineral Economics Section, which was established in 1947. Australia's slowness to develop a Federal bureau for the mineral industry can best be explained in the light of her political history. From a group of British crown colonies, Australia evolved into six sovereign states which had no unified federal government until they formed the present Commonwealth in 1901.

Jan 1, 1970

By E. W. Filer, R. P. Smith, L. S. Darken

The solubility of nitrogen gas in purified iron and low alloy steels is determined for the y region (930° to 1350°C). The diffusivtiy of nitrogen is estimated from the rate of approach to equilibrium. The investigation of aluminum-killed steels, held in nitrogen, discloses precipitation of aluminum nitride, the solubility of which is determined. ALTHOUGH several investigations of the solu-bility of nitrogen gas in y iron have been reported, all have made use of the method adopted by Sieverts in his classic work, whereby the solubility is determined by the pressure or volume change of the gas. The agreement between different investigators* is rather poor, particularly as compared to the self-consistency of results of several individual investigators. The present report represents a portion of our investigation of the equilibrium of nitrogen and nitrogenous atmospheres with iron and steels. The method adopted in this temperature region (910" to 1400°C) consists of holding the specimen in gaseous nitrogen, quenching (or cooling), and determining the nitrogen content by direct analysis (solution in acid followed by distillation and titra-tion of the ammonia).** Up to 1050°C a 20 in. vertical wire-wound (Kan-thal) furnace was used; this was wound in three sections so that by proper adjustment of relative currents, and use of a modulator1 and a commercial controller (using a chromel-alumel control couple), a zone almost 6 in. long could be maintained uniform within a few tenths of a degree. Since the temperature coefficient of the nitrogen solubility is low, the full precision was not utilized and a variation of l° to 2" was tolerated; a variation of a similar amount also occurred occasionally between the beginning and end of the experiment. At higher temperature a vertically mounted, tubular Globar furnace and control unit was used; the zone of uniformity (l° to 2"C) was here limited to about 2 in.; fluctuations with time were comparable to those in the wire-wound furnace. Reported temperatures were measured by use of a platinum-platinum-rhodium thermocouple, which was frequently com- pared with a similar standard couple which was calibrated at the gold and palladium points and also compared with one certified by the Bureau of Standards; error from this source is believed to be less than 1 "C. Nitrogen gas from a commercial cylinder was mixed with slightly over 1 pct H by use of a gas mixer described previously.' This mixture was passed over hot copper and through ascarite and phosphorus pentoxide to remove oxygen and water vapor. The purified gas contained 1.05 pct H. This procedure was adopted to prevent the formation on the specimens of oxide film, which is well known to be nearly impervious to nitrogen; its success was attested by

Jan 1, 1952

By R. Bakish, C. S. Barnett

IN experiments on tantalum strained in tension, Bechtold did not observe deformation-twinning even at a temperature as low as that of liquid air.' This is an unexpected behavior for a metal of body-centered-cubic structure. Therefore, it is desirable to determine whether the lack of twinning is an inherent characteristic of this particular metal, or whether the reluctance to twin can be overcome under suitable conditions. The following experiments were performed under conditions favorable to twinning and cleavage in their competition with slip, namely, with impact loading on large-grained sheet at low temperatures. The crystallography of cleavage in tantalum sheet was also investigated carefully because of the remarkable ductility of tantalum at low temperatures and because recent tests on oxygen-embrittled tantalum had disclosed unusual cleavage behavior for a metal of this structure: cleavage primarily on (110) planes and only occasionally on {100}.2 The tantalum, supplied by Fansteel, was of 99.9 pet purity, with the chief impurities being iron (0.03 pet) and carbon (0.03 pet). Coarse grains were produced by the strain-anneal method, the anneal being 4 hr at 2000°C in a vacuum of 10-3 mm Hg, followed by furnace cooling. Impact deformation was applied in various ways: a) by hammer blows on an anvil, the specimen and anvil being immersed in liquid nitrogen ( —196°C), b) by driving a precooled center-punch into the sheet, and c) by bending around a crystallographically determined axis with a hammer blow. The impact-deformation produced bands and slip lines on the surface, Fig. 1. The bands have every appearance of being deformation twins, a) They are tilted with respect to the untwinned surface. b) They have the appearance of Neumann bands in iron, thin lens shape, some having serrated edges. c) The orientation in each is different from that of the surrounding matrix and uniform within a given band, see slip lines within them in Fig. 1. d) Upon repolishing and etching, the difference in orientation and the resemblance to Neumann bands is again evident, Fig. 2. (In this micrograph the slight bend in the bands as they cross grain boundaries was noted frequently and results from the high degree of preferred orientation in the sheet.) e) The bands persist after annealing treatments that would have removed them had they been a low-temperature martensitic phase, e.g., after an anneal of 1/2 hr at 900°C. When back-reflection Laue data were plotted for single-surface analysis of several grains, every trace of the bands in each grain could be explained by (112) planes. In addition, two of the bands were located in space by traces on two surfaces, and these also were found to lie on (112) planes within the error of the stereographic plot. Since (1 12) is the anticipated composition plane for deformation twins in body-centered-cubic metals it is felt that the observations listed above are conclusive evidence for the identification of the bands as twins. Similar tests with impact at —77° and at 25°C produced no twinning. It is concluded that the critical shear stress for slip at the rates of straining used was always low enough to prevent the applied stress from reaching the value required for twinning at these temperatures. It was noted that the serrations along the edges of the twin bands exhibited parallel crystal facets. Several similarly oriented notches are visible in Fig. 1, and a remarkable set is shown in Fig. 3. It appears from Fig. 1 and similar areas that notches are frequently associated with the intersection of a slip line with a twin, although not all such intersections are at notches. In some instances a slip line appears to enter the twin, cross it, reflect from the opposite side and recross it, producing a pattern resembling a notch but without producing the notch itself, see Fig. 1. It is suggested that the stress concentration at the end of a slip line is responsible for these details. The strain energy associated with the pile-up of dislocations at a twin boundary may be lessened by untwin-ning or failing to twin a portion of the twin band, or

Jan 1, 1959

By S. F. Ravitz

In his excellent book on the Principles of Flotation, Warkl makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent float-ability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter2 presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism.l(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirin their results. The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen Pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally Pure galena was crushed by hand on a clean bucking board, screened to —I50+ 200 mesh, and deslimed on a 200-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1943

By S. F. Ravitz

In his excellent book on the Principles of Flotation, Warkl makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent float-ability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter2 presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism.l(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirin their results. The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen Pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally Pure galena was crushed by hand on a clean bucking board, screened to —I50+ 200 mesh, and deslimed on a 200-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1943

By G. H. Bishop

The kinetics of the inter granular penetration and embrittlement of [100] tilt boundaries in 99.998 pct pure nickel upon exposure to bismuth-rich Ni-Bi liquids have been determined in the temperature range from 700° to 900°C. The kinetics of penetration are parabolic in time at constant temperature over most of the temperature range. In a series of 43-deg bicrystals the rate of penetration is anisotropic with respect to the direction of penetration into the grain boundaries. In lower-angle bicrystals the penetration rate is isotropic. The rate of penetration decreases with tilt angle at 700°C. The activation energy for penetration in the 43-deg bicrystals is 42 kcal per g-atom independent of direction. It is concluded that the intergranular penetration and embrittlement in the presence of the liquid proceeds by a grain boundary diffusion process and not by the intrusion of a liquid film. This was confirmed by a determination that the kinetics of penetration and embrittlement were the same in the 43-deg bicrystals upon exposure to bismuth vapor under conditions such that no bulk liquid phase would be thermodynamically stable. WhEN solid metals are exposed to a corrosive liquid-metal environment, the grain boundaries are sites of preferential attack. Depending on the temperature, the composition of the liquid, and the composition, structure, and state of stress of the solid, a number of modes of attack are possible. This paper reports a study of the kinetics of intergranular penetration and embrittlement of high-purity nickel bicrystals upon exposure to bismuth which, together with an earlier study by Cheney, Hochgraf, and Spencer,&apos; demonstrates that there are at least two modes of intergranular attack possible in the Ni-Bi system. In the study by Cheney et al., columnar-grain specimens of 99.5 pct pure nickel were exposed to liquid bismuth presaturated with nickel in the temperature range 670" to 1050°C. They found that the majority of the boundaries, which were predominantely high-angle boundaries, were penetrated by capillary liquid films, the attack proceeding by a process which will be termed grain boundary wetting. This process occurs in a stress-free solid when twice the liquid-solid surface tension is less than the surface tension of the grain boundary,* i.e., when 2yLs < YGB In this case the penetration of the grain boundary by the liquid occurs at a relatively rapid rate, resulting in the severe embrittlement of a polycrystalline solid. Grain boundary wetting is a common mode of intergranular attack in systems in which the lower melting component is relatively insoluble in the solid, but the solid has an appreciable solubility in the liquid, for example, the Ni-Bi system, Fig. 1. In systems of this type at temperatures above the range of stability of any intermetallic phases, once the liquid is saturated with respect to the solid so that no gross solution occurs, chemical gradients are small, and surface tensions become major driving forces for attack, provided the solid is stress-free. The results of Cheney et al. appear to be typical of those encountered when grain boundary wetting occurs.&apos; Capillary films were observed in the boundaries after quenching from the exposure temperature. The mean depth of penetration increased linearly with time, and the activation energy for the process was found to be 22 kcal per g-atom. In a study of the Cu-Bi system Yukawa and sinott4 found that the depth of penetration of bismuth into high-purity copper bicrystals of orientations from 22 to 63 deg of tilt about (100) at 649°C ranged from 0.05 to 0.25 in. after a 12-hr anneal. This corresponds to a linear rate of 6 to 15 X 10~6 cm per sec. At the same reduced temperature of 0.68 the rate for the Ni-Bi system&apos; was 7 x lo-&apos; cm per sec. In another study of the Cu-Bi system, Scheil and schess15 determined the kinetics of grain boundary wetting in hot-worked commercial rod. While there were several complicating factors present in this study, there is general agreement with the above results. The kinetics of penetration were linear, the activation energy was 20 kcal per g-atom, and at 650°C the rate of wetting was 2 to 5 x 10-6 cm per sec. The rate of wetting in the A1-Ga system6 is somewhat

Jan 1, 1969

By Joseph R. Stephens

Deformation substructures of&apos; polycrystalline tungsten, W-2, 9, and 24 pct Re, and W-3 pct Ta were studied by tra?zsrnission electron microscopy. The stress-strain curve for unalloyed tungsten showed gradual yielding followed by work-hardening. Electron nzicrographs indicated a gradual increase in dislocation density with increase in strain up to 5.0 pct. Dislocations, although frequently jogged, were straight over moderate distances and were in a randorn array. Stress-strain curves for alloy specimens of W-2 and 9 pct Re and W-3 pct Ta exhibited a drop in stress at yielding followed by only slight work-hardening. Electron micrographs of these specimens after strains of 0.05, 0.1, and 0.5 pct revealed no change in dislocation substructure from the unstrained specimens. After 2.0 pct strain, the three alloys exhibited dense networks. W-3 pct Ta was characterized by straight, frequently jogged dislocations comparable with the dislocation structure in unalloyed tungsten after a similar amount of strain. In contrast, W-2 pct Re exhibited dislocations that contained widely spaced jogs, while W-9 pct Re had developed a cell structure after the relatively srnall strain of 2.0 pct. The W-24 pct Re alloy contained a few dislocations after 0.1 pct strain, while after 0.5 pct strain twins were evident. Dislocation slip bands apparently preceded the twins. The stress-strain curve for the alloy indicated that twinning commenced after approximately 0.25 pet strain. These results indicate that the primary effect of low rhenium concentrations (2 and 9 pct) in tungsten is to increase dislocation multiplication after macroyielding by reducing the Peierls-Nabarro force (lattice resistance to dislocation motion). The dislocation bands that precede twins in W-24 pct Re may be caused by localized internal stresses resulting fro a metastable structure, for example, clustering of rhenium atoms. The effect of high rhenium additions (22 a 65 pet* Rproperties of tungsten. Klopp, Witzke, and Raffo5 reported bend transition temperatures as low as -100°F (200°K) for dilute electron-beam-melted W-Re alloys tested in the worked condition. Recrystalliza-tion increased the bend transition temperature, but alloys with 2 to 4 pct Re were still markedly superior to unalloyed tungsten. Fractographic examinations of tungsten and W- 3 pct Re and W- 5 pct Re alloys by Gilbert 6 revealed that these low rhenium alloys showed a greater tendency toward cleavage failure than did tungsten. Garfinkle 7 showed that rhenium additions, up to 9 pct, to (100) oriented tungsten single crystals increased the proportional limit stress and decreased the flow stress and the rate of work-hardening. In addition, while deformation in unalloyed (100) oriented crystals apparently involved both (110)100) and (112) slip, crystals with rhenium contents of 5 andpct or more deformed primarily by (112) slip. The mechanism by which high and low rhenium additions affect the mechanical properties of tungsten is still not well-established. The present investigation was undertaken to determine by transmission electron microscopy the effects of low rhenium additions, 2 and 9 pct, and a high rhenium addition, 24 pct, on dislocation substructure in the early stages of deformation of polycrystalline electron-beam-melted tungsten. Unalloyed tungsten and a W- 3 pct Ta alloy were included for comparison. EXPERIMENTAL PROCEDURES Materials. Triple electron-beam-melted tungsten, W-2, 9, and 24 pct Re, and W- pet Ta were used for this investigation. Chemical analyses of the cast ingots are given in Table I. A description of the starting metal powders and melting and fabrication pro-cedures for unalloyed tungsten and the W-Re alloys is reported.5 The W-3 pet Ta alloy was processed in a similar manner. Compression specimens measuring 0.300 in. (7.6 mm) in length by 0.130 in. (3.3 mm) in diam were machined from swaged rods. All alloy specimens were annealed in a vacuum of 8 x 10- 6 Torr (10&apos;2iVper sq m) for 1 hr at 3600°F (2255°K). The recrystallized grain size ranged from 0.06 to 0.08 mm diam for the alloy specimens. Unalloyed tungsten was annealed at 2400° F (1589°K) for 1 hr to produce a recrystallized grain diameter of approximately 0.12 mm. Specimens were electropolished in a 2 pet NaOH solution to a diameter of 0.125 in. (3.18 mm) to remove surface notches resulting from grinding and to improve reproducibility of t data. The ends o the compression specimens were ground flat, parallel to each other, and perpendicular to the longitudinal axes with 4/0 emery paper. Compression Tests. The compressive stress-strain apparatus used for compression tests is described in detail by Stearns and Gotsky.9 Room-temperature compression tests were conducted at a crosshead speed of 0.01 in. per min (0.25 mm per min).

Jan 1, 1969

By Thomas L. Kesler

Present Raw Materials The lithium industry has had exceptional growth since publication of the last edition of this volume, and the present scale of mining and consumption of raw materials is a great many times that of 1949. The materials of present economic importance consist of four pegmatite minerals and lithium-bearing brine. Spodumene, a lithium pyroxene, occurs in greatest abundance, and is the chief source. It has the formula LiAlSi2O6 and theoretically may contain 8.03 pct Li2O, but in the more important deposits the content is 6.5 to 7.5 pct. The hardness is 6.5, the specific gravity 3.1 to 3.2, and the color mostly pale green to white although deep green, lilac, and yellow varieties exist. The crystals are prisms with strongly developed longitudinal cleavages, and crushing characteristically produces lath-shaped particles. Giant crystals up to 47 ft long are known, but in most occurrences the predominant size range is 0.5 to 12 in. long and 0.1 to 2 in. wide. Hypogene* alteration has formed lithia-bearing sericite and coarser muscovite and rarely eucryptite, while supergene* alteration yields kaolinite and hydrous mica. Lepidolite, of second importance, is a mica of varying composition approximating K2Li3-A14Si7O21(OH,F)3. It has lamellate cleavage, book structure, and a specific gravity of 2.8 to 3. The books range in size from microscopic to a diameter of several inches. The color is mostly violet, but other colors include pink, gray, yellow, and white. Most commercial lepidolite contains 3 to 4 pct Li20 and chemically is in the higher grade range of a series of lithium micas that includes polylithionite, zinnwaldite, and protolithionite. In this series, the content of Li2O is exceptionally as high as 7 pct. Petalite and amblygonite are also of economic importance, but are used in smaller amounts. Petalite has the formula LiA1Si4O10 and is white, gray, or pink. The hardness is 6, the specific gravity 2.4, the cleavage in two planes 114° apart, and the Li2O content commonly 3 to 4.7 pct with a maximum of 4.88. Amblygonite has the formula LiA1FPO4 in which OH may substitute for F to form montebrasite. It is white and has polysynthetic twinning in two directions at 90°. Amblygonite superficially resembles potash feldspar, but has a bluish or grayish tint unlike the cream or salmon tint of the feldspar.[t] The hardness is 6 and the specific gravity 3 to 3.1, and the content of Li2O is the highest among lithium minerals that occur in significant quantity, ranging mostly from 7.5 to 9 pct with a maximum of 10.2. The brine of Searles Lake in California30 has been a commercial source of lithium since 1938. See Chap. 7, p. 108. The "lake" is a saline evaporite deposit, and the exposed part has an area of 12 sq mi. To an average depth of 71 ft, this part of the deposit consists of crystalline salts with 50 pct interstitial voids. The voids are filled with brine that contains mainly sodium and potassium compounds, but the brine also contains 0.015 pct Li2O, which is recovered as dilithium sodium phosphate containing 21 pct Li20. This deposit overlies a

Jan 1, 1960

By F. A. Olson, J. S. Cho, M. E. Wadworth

An infrared study of the states of hydration of MgSO4 revealed a hitherto unreported metustable dehydration state in the temperature range just below that of the stable anhydrous salt. Infrared, thermogvavimetric, and X-ray studies indicated that the state had bisulfate and hydroxide characteristics. A formula fitting all of the experimental evidence is hydrogen-bonded Mg(OH)HSO4, or possibly the chemically equivalent 1/2 Mg(HSO4)2. Mg(OH)2 Infrared spectra of the 7, 6, 1, and OH2O states of hydration are given as well as the spectra of the newly found state which is called the bisulfate state in this paper. Thermogvavimetric studies as a function of water-vapor pressure gave an enthalpy value of 16 cal per mole, and 25 eu for the conversion of the bisulfate state to that of the anhydrous salt. The free energies of the transition varied from 1.76 to 0.18 kcal per mole as the transition temperature varied from 279° to 336°C. The bisulfate state is believed to be of importance in catalytic dehydration phenomena using MgSO4 and may be of interest because of properties in sulfating reactions differing from those of the monohydrate. Also, an analogous state may exist as a hydration state of other sulfates. ANHYDROUS magnesium sulfate is a catalyst with a high degree of specificity for the dehydration of secondary alcohols.1&apos;2 The only product obtained at the usual operating temperature range of 360" to 400°C other than the corresponding olefin is water. Thus, the bonding of water to the anhydrous salt as well as an understanding of the hydration states of MgSO4 became of interest in attempting to understand the catalytic mechanism better. In the process of this study using infrared, X-ray, and thermogravimetric analyses a dehydration state not previously reported was found. Proof of its existence, the nature of the state, and its role, if any, in the catalytic mechanism then became of interest. This paper is concerned principally with the first two aspects of this problem. Magnesium sulfate forms many hydrates, of which the monohydrate and heptahydrate (Epsom salts)3 are most important. Other hydrates4 are known with 1-1/4,5 l-1/2, 5 2, 4, 5, 6, and 12 H2O&apos;s. The hydrates with 1-1/4, 1-1/2, 2, 4, and 5 HzO&apos;s are unstable. The anhydrous salt is very stable thermally and has a strong affinity for water. It can be heated without additional decomposition to about 800°C.&apos; At 900°C noticeable decomposition takes

Jan 1, 1964

By B. Post, F. W. Glaser

Three borides of zirconium have been reported: ZrB,l ZrB2,2,3 and ZrB12, 4 The phase relationships, ranges of stability, and some physical properties of these compounds are described. THE zirconium borides differ considerably from one another, particularly with respect to their relative stabilities at high temperatures in the presence of carbon.4,5 ZrB2 is extremelv stable at all temperatures (to the melting point) in contact with carbon. Both ZrB and ZrB12 tend to decompose at elevated temperatures when carbon is present in excess of about 0.5 pct. ZrB forms ZrB2 and ZrC, and ZrB12 decomposes to form ZrB2 and a boron-carbide phase. In the ZrB12 preparation, boron present in excess of that needed to form ZrB2 reacts with carbon, if present, to form carbides, in preference to forming the higher boride. Similar instability of borides, other than diborides of the transition metals of the 4th and 5th groups of the periodic table, has been reported.5,6 special precautions had, therefore, to be taken to minimize carbon contamination in the preparation of ZrB and ZrB12. Reactions below 1400°C were carried out by heating powdered mixtures of zirconium hydride and boron in quartz tubes in a hydrogen atmosphere. For temperatures above 1400°C, reactions were carried out in graphite molds. Carbon contamination from the molds was minimized by employing extremely rapid heating rates to reduce carbon diffusion into the body of the specimen, and by subsequent "shaving" of sample surfaces that had been in contact with the graphite dies. A heating rate of about 2000°C per min was obtained by heating the dies (by direct conduction), using a current of 40,000 amp. Although this type of heating cycle apparently allowed little time for "homogenization," close approximations to equilibrium conditions were usually obtained as a result of the very strongly exothermic reactions between zirconium hydride and boron at elevated temperatures. Reproducibility of results in repeated runs under varying conditions was taken as a reasonable indication that equilibrium conditions had been effectively achieved. Quenching was accomplished by rapidly immersing the entire die, containing the reaction products, in water. Specimens could also be cooled at controlled rates by adjustment of the rate of flow of water through the water-cooled copper electrodes in contact with the graphite dies.

Jan 1, 1954

By J. W. Spretnak, G. W. Cunningham

A study has been made of the growth and disappearance of voids in the interface of pressure bonded copper. The formation of visible voids is primarily due to spheroidization and coalesence of microvoids produced during the application of pressure. The microvoids could be prevented from forming by the application of high pressures or by increasing the ductility of the copper. Migrating grain boundaries were found to be more effective in void removal, than stationary grain boundaries. DURING the course of an investigation on the mechanism of pressure bonding, it was found that voids formed in the bonding interface which inhibited migration of the interfacial boundary and grain boundaries in the bond region. Therefore, an effort was made to determine the nature of the voids and how they form, grow, and disappear. This paper reports the results of such an investigation. The existence of interfacial voids is not solely a characteristic of massive components of metal which have been bonded by the application of heat and pressure, but is a phenomenon which has been observed in sintering as well. Simonsen attempted to study the sintering process by hot-stage microscopy and thereupon observed the formation of interparticle porosity as sintering proceeded. It was assumed that the porosity was due to grooves created at the location where grain boundaries joined the surface of the particle. Pranatis, Castelman, and seigle2 have also observed voids along the areas of contact in wound-wire specimens used for sintering studies. They did not discuss the point in detail since this behavior was not general, but they did suggest that the voids might develop as a result of stresses along the interparticle contact area. In previous investigations on pressure bonding, workers3 have suggested that voids may exist in the region where mating surfaces are placed in intimate contact, but the existence of the voids was not verified and no attempt was made to study the growth and disappearance of these voids. Durst noted the existence of pores in roll-clad structures prepared by cold reducing two sheets to force them in contact and then annealing to improve the bond. Since his unbonded regions contained a gas which he assumed to be insoluble, he proposed a mechanism which consisted of spheroidization of the unbonded regions and a growth of the contact area, but no speculations were made regarding disappearance of the gas filled pores. One interesting comment made by Durst was the suggestion that flattened voids with sharp corners which are produced during roll bonding will have a greater driving force for spheroidization than the more rounded pores created by pressing metal powders and thus spheroidization and neck growth will occur at lower temperatures. In this study it was necessary to demonstrate conclusively that voids can actually exist in the interfacial bond area. Experimental work was then directed toward a study of the mechanism whereby the voids grow and subsequently disappear.

Jan 1, 1963

By J. W. Downey, M. V. Nevitt

MUELLER and Knott&apos; have reported that Ti2Cu has the Si2Mo-type (Cllb) structure. The lattice parameters of Ti2Cu and the positions of the titanium and copper atoms are given by them as follows: ao = 2.944A; co = 10.786A 6 atoms per unit cell: 2 Cu (a) 000; 1/2: 1/2, 1/2 4 Ti (e) 002; 1/2, 1/2, 1/2 + z 00 -2 ; 1/2. 1/2. 1/2- z where z = 0.341 We have found eight other binary compounds which appear to be isostructural with Ti2Cu. All of them involve the combination of a titanium group element with a copper group element or a titanium group element with palladium. The compounds and their lattice parameters are given in Table I. The alloy samples were prepared by arc melting metals having a purity of 99.9 pct or better. They were homogenized for 72 hr at 900°C in evacuated capsules and quenched in tap water. Filings were prepared, and these were reannealed for 4 hr at 700°C, also in evacuated tubes. The lattice parameters were determined by a least squares Bnalysis of the back reflection lines of patterns made with cobalt radiation. It was not possible to make a precise determination of the lattice parameters of Zr2Au because the filings underwent rapid oxidation at room temperature. The evidence supporting the large tetragonal cell containing 6 atoms involves the presence of the reflections 002, 101, 004, 112, 114, 202, and other reflections with higher indices for which I = 3n. Three or more reflections corresponding to these indices, which cannot be indexed on the basis of a small body-centered tetragonal cell containing 2 atoms, are observed in the patterns of all of the compounds listed in Table I. They are strongest and most numerous when the components have large differences in their atomic scattering factors, as is the case in Ti2Pd, Zr2Cu, and Hf2Cu. The values of the z parameter should be regarded as approximate They were selected on the basis of the best agreement between the observed intensities of two pairs of closely spaced powder pattern lines (004): (112) and (114): (202) and the corresponding intensities calculated for several values of z. An ordering scheme was assumed in which titanium, zirconium, or hafnium atoms occupy the titanium positions of Ti2Cu, and copper, silver, palladium, or gold atoms occupy the copper positions. Calculated and observed intensities of the aforementioned lines and the other lines of the patterns are in satisfactory agreement, but a refinement of the z parameters and a final confirmation of the ordering arrangement must await a more detailed study. It is interesting to note that in transition metal systems at A2B stoichiometry the Si2Mo-type structure competes for stability with two other fre-

Jan 1, 1962

By A. C. Fieldner

IN the Wall Street journal for March 1, 1941, was a tabulation of the construction under way or under negotiation by thirteen iron and steel companies for a predicted increase in annual coke production of 3,165,600 tons. That even this figure was short of the mark is indicated by other plans, then being considered, for a later expansion of 2,610,000 tons additional. Considerable progress has already been made on thin program, for approximately 500 new ovens were put in operation in 1941. and well over 200 should be completed in 1942. These figures include a number of units that replace older and obsolete equipment.

Jan 1, 1942

By S. C. Sun, John A. L. Campbell

The surface properties exhibited by bituminous coal and bituminous coal lithotypes were ascertained by using streaming potential techniques. The electro kinetic prop-erties wereascertainederties of bituminous coal were found to be similar to those of anthracite. The principle electrokinetic properties of the coal and lithotypes, zero-points-of-charge (ZPC), and potential determining ions, were established. The effects of indifferent electrolytes, hydronium and hydroxyl ion sources, and polyvalent ions (cationic and anionic) were also evaluated. Location of the ZPC&apos;s with respect to pH is discussed in terms of chemical and mineralogical composition of the respective surfaces. To account for the observed electrokinetic phenomena, a generalized surface model and adsorption mechanism are proposed. Surface-dependent processes, such as froth flotation and flocculation, are important or potentially important techniques for combating some of the current major problems in coal preparation. In order to correctly apply or improve a surface-dependent process, it is of paramount importance to understand the interfacial phenomenon, especially the double layer properties, exhibited by the solid. The specific objective of this research was to determine the properties of the bituminous coal/liquid interface by an electrokinetic method, streaming potential, and to relate the findings, wherever possible, to the existing unit operations of froth flotation and floccula-tion tion. The electrokinetic properties of both the whole coal and its lithotypes were investigated. As part of the total investigation, the role played in the double layer by the reagents commonly employed in the surface dependent process was also established.&apos; These data will be presented at a later date. Experimental Procedures The coal samples used in this research and their designations are listed in Table 1. The classical description of humic coal lithotypes as developed by Stopes" was used for the delineation of the lithotype samples. The samples were taken from the working face of a producing deep mine of the Pittsburgh seam in the area of Ellsworth, Pa. To avoid oxidation, only freshly exposed areas were sampled. The normal precautions against contamination were also exercised. Two types of samples were taken, specimens rich in a particular lithotype and a representative channel sample. The latter sample was prepared for analyses by grinding it to —35 mesh. It was screened repeatedly during the grinding to provide the largest amount of 35 x 48-mesh (standard Tyler sieves) material possible. The screened fraction was passed over a magnet and then washed several times with distilled water and finally with conductivity water. The resulting sample now termed "whole coal" was stored under conductivity water in a glass bottle. Pure lithotypes were obtained from the lithotype concentrates by hand picking, and were processed in the same manner as the representative sample. Maceral analyses, employing standard petrographic procedures," were performed on the lithotype samples to determine the purity of the samples. The results are presented in Table 2. Reflectance measurements of the vitrinites and fusinites are also reported in this table. Proximate and ultimate analyses of the samples are given in Tables 3 and 4. The electrokinetic properties of the coal samples were determined by streaming potential methods.&apos;-&apos; All of the chemicals used in the investigation were reagent grade (Baker analyzed). The conductivity water was prepared by doubly distilling the water in a pyrex Yoe-type still and passing the distillate through a mixed bed ion exchange column. Results In general, the electrokinetic properties of the investigated bituminous coal were found to be similar to the results of a previous study of anthracite by Camp-bell bell5 and are in accord with the suppositions of Brown." The zeta potentials of the coal and all the lithotypes were found to be negative in conductivity water. Jowett? in a study of slime coatings on coal also found bituminous coal to exhibit a negative surface. Fig. 1 shows that the negative charges, at neutral pH&apos;s, for both fusain and the gangue are very small, almost zero, while at the same pH, vitrain has the largest negative charge, almost 30 mv. Durain has a negative charge of 17.5 mv. The determination of the affect of pH on the charge of the coal surfaces revealed that hydronium and hydroxyl ions apparently behave as potential determining ions; however, they do not appear to be potential determining for the gangue. These results are illustrated in Fig. 1. As the pH of the solution was decreased, hydronium ions were adsorbed, causing the surface of the coal to reverse polarity and become

Jan 1, 1971

By Robert E. Green, T. Hinton

The velocities of the three possible modes of elastic-wave Propagation have been calculated for single-crystal aluminum at 1-deg intervals throughout the standard steveographic triangle. The results are presented as isospeed contours. The deviations between the direction of maximum energy propagation and specirzen axes are presented as arrows drawn within the standard triangle. The orientation factors associated with dislocation nzotion on the primary slip system only and also on all twelve slip systenzs have been calculated for all three elastic waves. The orientation factors associated with a longitudinal standing--7aue resonant specivnen hazle also been calculated. The relevance of these results to ultrasonic attenuation measurements is discussed. DUE to the widespread use of ultrasonics in the investigation of the properties of solids a number of authors15 have discussed in detail the theory of elastic-wave propagation in solids. In this paper the modes of wave propagation are evaluated according to the procedure suggested by reeen&apos; for the case of single-crystal aluminum at 1-deg intervals throughout the standard stereographic triangle. The wave speeds are presented in the form of contour diagrams within the standard triangle. The deviations between the direction of maximum energy propagation and the normals to the wave fronts are presented as arrows drawn within the standard triangle. The orientation-de pendent factors (orientation factors) associated with dislocation damping as derived in the preceding paper6 have been calculated for the case of aluminum at 1-deg intervals throughout the standard triangle. The orientation factors for dislocation motion on the primary slip system only and on all twelve slip systems are presented in the form of contour diagrams, for both the traveling- and the standing-wave conditions. The relevance of these results to ultrasonic attenuation measurements is discussed. ELASTIC-WAVE PROPAGATION Three waves can be propagated in a linear elastic homogeneous anisotropic medium. The velocity of propagation v of each of these waves in a medium of density p can be obtained from the determination of the eigenvalues and eigenvectors of the matrix equa- The A&apos;s are a series of moduli which are functions of the elastic constants cij and the direction cosines 1, m, and n of the specimen axis. In the case of cubic single crystals where there are only three nonzero elastic constants cll, c12, and C, the A&apos;s are, The solution of Eq. [I] will give the wave speeds (eigenvalues) and the direction cosines a, 0, and y of the particle displacements (eigenvectors). To obtain the direction of maximum energy flux requires the calculation of the energy-flux vector ET with com- w is the angular frequency, A, the amplitude, and v the velocity of the wave. The direction cosines a, b, and c of the energy flux vector are then given by

Jan 1, 1967

By Avnulf Muan, Egil Aukrust

The activity-composition curve for cobalt oxide in (Co,Fe)304 solid solutions with spinel-type stmcture has been determined experimentally by studying the equilibrium between the spinel phase and a coexisting cobaltowüstite phase, "(Co,Fe)O", at 1200°C. A large negative deviation from ideal behavior prevails in the spinel at low cobalt oxide concentrations and a positive deviation at high cobalt oxide concentrations. The activity-composition curve for iron oxide in the solid solution is determined from the above curve by integvation of the Gibbs-Duhem equation along the join Co3O4,-Fe3O4. The standard free energy of formation of cobalt ferrite, CoFe2O4, from the oxide components CoO and Fe2O3 is calculated to be -8.2 kcal. ThERMODYNAMIC properties of (CO,Mn)3O4 solid solutions with spinel-type structure have been presented recently.&apos; The present paper deals with similar relations in another spinel solid-solution phase, that represented by the system Co3O4-Fe3O4. The principles involved in measurements and calculations of thermodynamic properties for the system Co3O4-Fe3O4 are analogous to those used and discussed in detail in the work on (CO,Mn)3O4. A (CO,Fe)3O4 solid solution coexists in equilibrium with a (Co.Fe)Ot solid solution over a considerable Here acOo1.33 and aao are the activities of cobalt oxide in the spinel and the oxide solid solutions, respectively, pO2, is the oxygen pressure of equilibration, and pb, is the oxygen pressure at which CoO and CosO4 coexist in equilibrium in the binary system Co-O at the same temperature. The activity-com position curve for cobalt oxide in the (Co,Fe)O solid solution in contact with metal has been determined in a previous investigation by the present authors.&apos; The system shows a small positive deviation from linear behavior. Because of the large defect concentration in wiistite and in (Co,Fe)O solid solutions, one cannot assume that the activity-composition relations in the oxide phase coexisting with a spinel phase at relatively high oxygen pressures are the same as those prevailing in the oxide solid solution coexisting with metal. However, a Gibbs-Duhem integration over the ternary Co-Fe-0 solution can be used to determine activities of cobalt and iron, and hence of CoO and FeO, from a knowledge of the oxygen potentials. Several papers have dealt with the subject of application of the Gibbs-Duhem equation to multi-component systems. 3-6 In the present case, it was

Jan 1, 1964

By C. H. Ault, D. D. Carr

Four counties in Indiana- LaPorte, Vigo, Vanderburgh, and Switzerland-have potential for deep underground limestone mining because they are in or near high population areas and have no surface-mineable limestone deposits. The principal markets are Gary-South Bend, Terre Haute, Evansville, and Cincinnati. Mineable seams suitable for aggregate are 120-150 m (400-500 ft) below the surface in LaPorte and Vigo Counties, about 90 m (300 ft) below the surface in Switzerland County, and about 600 m (2,000 ft) below the surface in Vanderburgh County. Some deposits are also suitable for high-purity uses or for cement raw materials, which enhances their potential for exploitation.

Jan 1, 1983

By T. G. Lovering

Nonparametric statistical tests have practical application to many geological problems because, unlike the standard statistical tests, they do not require assumptions regarding the form of the population frequency distribution. Many of them do not even require that the variable be susceptible to numerical measurement. These tests are useful either 1) for geological data representing population distributions of unknown form, or otherwise not meeting the requirements for standard parametric tests; or 2) for sample attributes that cannot be measured but only ranked in order of relative magnitude. The application of two such tests will be illustrated. The Kolmogorov-Smimov test will be used to test for significant differences in copper distribution in samples of two rock types; the Spearman rank-correlation method will be used to determine whether there is a significant association between intensity of rock alteration and copper content of the rock. Nonparametric tests are, in general, quicker and easier to perform than the corresponding parametric tests, and they may be applied to a greater variety of data. They are not as powerful as the standard tests if used on data to which the latter are applicable, and computer programs utilizing them are not generally available. The use of standard or parametric statistical procedures for the interpretation of measured geological data is familiar to most mining engineers and explora- tion geologists. The computation of product moment correlation coefficients on sample assays for more-than one component is already standard procedure in some company operations, as is the use of Student&apos;s F test and Snedecor&apos;s F test for the comparison of means and variances of sample groups. The application of these three tests is limited by the prerequisites that the samples must be random, independent representatives of normally distributed populations and that the variables involved must be measurable. If such tests are applied to data which fall short of fulfilling these prerequisites, then the probability level attributed to the computed statistic is invalid and the conclusions based thereon may be erroneous. A number of nonparametric, or distribution free, statistical tests have been developed for use with data which are not amenable to standard parametric procedures. These tests have been widely used in the behavioral sciences such as psychology and sociology for some time, but their application to geologic problems is relatively new. Nonparametric tests may be grouped into two main categories: those which test for significant differences in a single variable by comparing either sample values with a standard value or representative values between two or more groups of samples; and those which test for significant association between pairs of variables in a single group of samples. The versatile chi square test, the Kolmogorov-Smirnov one and two sample tests, the Wilcox matched pairs signed ranks test, the median test, the Mann-Whitney U test and the Cochran Q test are examples of nonparametric tests with demonstrated or potential geological applications that belong in the first category. The contingency coefficient, Spearman rank correlation coefficient, Kendall rank correlation coefficient and the

Jan 1, 1963

By S. F. Ravitz

IN his excellent book on the Principles of Flotation, Wark&apos; makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent floatability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter&apos; presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism. I(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirm their results. EXPERIMENTAL PROCEDURE The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally pure galena was crushed by hand on a clean bucking board, screened to - 150+ 200 mesh, and deslimed on a zoo-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1940

By Axel Hultgren

In ingots of silicon-killed carbon steel-made without addition of aluminum, transparent spherical or nearly spherical inclusions, up to about 0.15-mm diameter, are generally present. They may be glassy or crystallized, wholly or partially In steels of high carbon contents they consist of silica,4,12 in steels of lower carbon contents and, in consequence, higher oxygen contents, of iron-manganese-silicate with higher iron and manganese contents the lower the carbon content. Small silicate inclusions, about 0.01 mm or smaller, may occur, just as sulphide inclusions do, in portions that have been the last or nearly the last to freeze,l0,12,17 this location being verified by primary etching.10 Hence, it may be concluded that they have separated from liquid steel that has become enriched in oxygen through segregation during freezing. Silicate inclusions with a diameter larger than about 0.02 mm appear, at least in ingots of moderate size, to be distributed at random in relation to the primary structure and therefore may be assumed to have existed as droplets in the liquid steel before freezing started at the point in question. The average size of such large inclusions has been found to increase toward the axis1&apos; and their amount to increase from the top downward in the axial region.2,10 It has been assumed that this accumulation is a result of the droplets being brought down by the slowly settling metal crystals.2 It has been suggested that large silicate inclusions generally form,6 or may form,&apos;&apos; by coagulation of smaller ones, or by small drops being caught by larger ones during the rising of the latter.9 The occasional occurrence of a large inclusion surrounded by a swarm of small ones has been taken as a proof of this mechanism but, as suggested later, may be explained in another way. It has been pointed out that an inclusion droplet in the liquid steel may grow at the expense of an adjacent one, which implies diffusion of soluble inclusion-forming elements in the liquid steel.&apos;= Further, it has been pointed out that, on cooling in ladle or mold, the metal-silicate equilibrium is displaced in the direction of separation of silicate. Thus inclusions may grow in size and amount.2,3,8,12,13,17,19,20 The exposure of the liquid steel to the oxygen of the air during tapping and pouring, and the consequent reaction, has been mentioned as a source of the formation of inclusions19.20 but this possibility has not received particular attention. Further, the admixture of furnace slag during tapping1 or of refractory material from various sourcesl,20 has been considered. The inclusions due to the latter may be recognized, however, through their resistamce to hydrofluoric acid, imparted by the alumina content. Silicate inclusions are often referred to as the natural and inevitable product of reaction on adding silicon or silicon

Jan 1, 1949