Search Documents

By Bruno Bussière

Acid Mine Drainage (AMD) from mine wastes is one of the most environmental challenge currently facing the mining industry. AMD is the result of the natural oxidation of sulphides exposed to air and water. When mining wastes have the potential to produce AMD, these reactive wastes have to be managed to meet existing environmental regulations. The LTA site (property of Barrick Gold Corp.) contains sulphide tailings that have the potential to generate AMD. The closure option Barrick selected was to construct a multilayered cover with capillary barrier effects (CCBE). The main objective of this CCBE is to prevent the production of Acid Mine Drainage (AMD) from the tailings stack covering an area of approximately 60 ha. Since its construction in 1996, the cover has been monitored to evaluate its performance. Two of the measured parameters are volumetric water content and matrix suction. This paper presents some of the main results from the monitoring program that started seven years ago. The results show that the cover is largely able to maintain a high degree of saturation (greater than 85%) in the moisture-retaining layer. The actual performance of the CCBE on the flat surface of the 60 ha site is even better than expected at the design stage. The area that requires more specific attention with the LTA cover is the influence of slopes that can reduce the performance of the CCBE during dry periods. However, these effects seems to be local and do not significantly affect the overall performance of the CCBE to mitigate the production of AMD at the LTA site.

May 1, 2003

By C. Bissue, G. M. Castillo

Newmont’s Phoenix mine started production in March of 2006. Due to the extreme hardness of the ore, the mill has struggled to meet throughput projections. Grinding studies showed that optimizing the existing circuit would not achieve budgeted throughput. These studies also showed that the pebble crusher was being underutilized due to the inability of the SAG mill to break the rock. The concept was developed to supplement the feed to the existing pebble crusher with a secondary crusher. Models of this process looked favorable so a portable crusher was installed to test the process. The temporary crusher was successful at increasing the throughput by 7% and based on the operating data, plans are currently being developed to install a permanent secondary crushing system in front of the SAG mill. This paper will review the results from the test crusher and the flow sheet for the permanent secondary crusher.

Jan 1, 2012

By G. C. Weatherly, D. S. Wilkinson, A. M. Limarga

In addition to the harsh environment, materials for high-temperature applications are often subjected to a significant mechanical loading. Several researchers have noted that the rate of oxidation can be affected by stress in a range of materials. We have recently studied this effect in y-TiAl, based on the preliminary work of Magnan and Weatherly which showed that nitridation rates on the tensile side of a flexural creep specimen could be 10 times higher than on the compressive side. We have since developed a four-point bending creep setup capable of controlled atmosphere testing. We present quantitative data on the effect of creep on scale growth under a range of atmospheric conditions. Finite element analysis will also be used to show how modest applied stresses can have a large effect on scale growth rates through the generation of large stresses due to the mismatch of creep rate between the metallic substrate and the scale.

Jan 1, 2004

By Q. Dong, S. A. Nightingale

An investigation has been carried out to assess the effects of an applied voltage on the dissolution rate of MgO refractory in a steelmaking like slag. In this study corrosion results obtained from dip tests using a dense direct bonded MgO refractory in a CaO-SiO2-Fe2O3-FeO-MgO slag are presented. These results demonstrate that the application of a voltage across a dense MgO refractory-slag interface can change the rate of refractory dissolution. For the slag composition used and the voltage range tested, it was found that a maximum corrosion rate was obtained at a voltage setting of -0.45V. The results of this investigation have been explained in terms of voltage affects on Marangoni (interfacial tension induced) stirring and its effect on the MgO dissolution reaction that is at least partly controlled by mass transfer in the slag.

Jan 1, 2004

By S. Afshar, C. Allaire

Several studied have recently shown that the use of non-wetting additives is not always a sufficient solution to improve the corrosion resistance of refractories against molten aluminum. Once in contact with liquid aluminum, the coarse aluminosilicate aggregates, which do not benefit from the protective effect of non-wetting additives in the matrix, may be corroded. In some cases, the corrosion of aggregates, especially those containing a significant amount of free silica and/or alkalis, promotes corrosion in the surrounding matrix. The present work explores the possibility to protect the poor corrosion resistant aggregates via a lining procedure. A slip casting method, using either alumina or celsian-like composition based slurries, has been applied for lining of a series of aggregates. The results from this study show that such linings may prevent efficiently the corrosion of aluminosilicate aggregates. This work also analyzes the effects of firing temperature and lining quality on the corrosion behavior of aggregates

Jan 1, 2004

By A. Siegmund, F. Mucciardi, Z. Yuan, B. Bulnes

With conventional heat pipe science as the starting point, a new heat transfer technology --- termed Thermopump technology, has been developed at McGill University and is now being tested at a number of industrial operations. This technology is of particular importance for transferring energy in high temperature / high heat flux environments where solutions based on current techniques are not available. One important application for this technology is in the metals recycling area wherein this technology has been used to make a waterless, non-consumable, high efficiency Thermopump oxygen lance. The viability and efficiency of this oxygen lance have been demonstrated by preliminary plant trials in a reverb furnace for the recycling of lead-acid batteries at the RSR Corporation. Full-scale commercial trials of the Thermopump (TP) oxygen lance have been carried out at the RSR Corporation. The results from these tests will be presented. In addition, some applications of the Thermopump technology for other metal recycling processes will also be discussed in this paper.

Jan 1, 2004

By F. M. Makarinsky

"This paper describes the conversion of conventional froth flotation cells to open-trough type bank cells, with 'buried' vertical metal partitions. These changes have resulted in: total froth removal along the full length of each bank of cells; extended flotation cell retention times; and has extended the life of the metal components, particularly towards the upper flotation cell areas.INTRODUCTIONOver the past twenty years, the flotation cells used at Falconbridge Limited, Sudbury operations concentrators, have gone through major physical changes. The various concentrators generally started with 100 cubic foot Denver Sub 'A' flotation cells. From these units, we progressed to 'converted' DR units, and/or Denver DR units, if purchased new. (Figures 1, 2, 3)In 1980, the Strathcona concentrator started to pay more attention to the 'front end' rougher flotation cells. Initially, the converted DR flotation cells had 'cut-outs' removed (Figure 4) at all upper vertical cell partitions, towards the ff9th lip areas, in order to get additional froth removal."

Jan 1, 1985

"Since the publication of a literature review on this topic (McIvor and Finch. 1986), the author has been involved in more than thirty rod milling efficiency tests at seven different milling operations. There have also been several interesting additional articles on rod milling found in the literature. This update describes the most important findings from investigations carried out since the previous review, as well as developments in the techniques used to evaluate the grinding efficiency of rod mills.Rod Mill Power DrawA series of power draw versus charge level measurements were taken on the rod mills at Leg Mines Selbaie and Kidd Creek Mines Limited (McIvor. 1989). These revealed a significant (about 10070) loss in power draw with the installation of new liners, a common observation among rod mill operators. This loss in power draw depends on the liner design, particularly the average thickness and lifting face profile of the new liner. The theoretical power usage of both mills was approximately 5070 lower than that given by the Allis-Chalmers power draw formula (Rowland. 1982).The shape of the power draw versus charge level curve suggested an opportunity for reducing media consumption. By increasing mill speed, power draw could be maintained with a smaller mill load, most significantly for mills operating with high charge levels. Analysis of data from 62 installations confirmed this (McIvor, 1989). On average, a 10 percentage point increase in critical speed results in a 15070 in specific media consumption (Le. kg of steel consumed per kWh of energy consumed). Table 1 lists a number of relatively high speed rod milling installations. No negative effects on the drive train, liner life, or the tendency for rods to tangle have been reported. A reduced lifting angle of the new liner leading face (e.g. 45 versus 90 degrees from the mill perimeter) is recommended for higher speed rod mills (Leclerq, 1990)."

Jan 1, 1995

By M. Fainerman-Melnikova

The use of strong base ion exchange resins for the extraction of uranium was pioneered in the 1950?s. Ion exchange technology is applicable to dilute leach solutions such as those obtained from in-situ, heap leaching or in-plant processing of low grade ores. A further advantage of ion exchange processes is that fluidised bed technology allows for treatment of solutions with a relatively high concentration of suspended solids and resin-in-pulp technology can treat leach slurries. However, the extraction of uranium with strong base resins is severely affected by the presence of chloride ions in solution. In areas where high quality water is not readily available, the use of saline water as process water would extend the potential application for ion exchange in uranium processing. Our research program has studied the effectiveness of a wide range of commercially available ion exchangers in uranium extraction from saline solutions. In the present work, we examine the impact of salinity (ranging from chloride concentrations found in groundwater to those present in sea water), on the uranium extraction with weak base anionic resins (WBA). The effect of pH and the presence of the competing impurities are also discussed.

Aug 1, 2010

By K. A. Lewandowski

Agglomeration of ore used in heap leaching allows for the immobilization of fine particles that would otherwise migrate and cause permeability problems in the heaps. For copper ore, binders are needed in order to make stable agglomerates. However, the majority of binders break down when introduced to an acidic environment, allowing fine particles to be released from the agglomerate surfaces. These particles migrate through the heap impeding solution flow, leading to a decrease in metal recovery rates. The authors have developed a series of testing procedures to determine the acid resistance of several binders. Only five binders were shown to be acid resistant in soak tests, decreasing fines migration by up to 93%, compared to tests which were agglomerated with leach solution, raffinate, as a binder. Flooded percolation column testing also showed that these binders were able to reduce the "slump" of the ore by up to 82% and increased the hydraulic conductivity by up to 90%, when compared to agglomerating with leach solution alone. The use of binders in the agglomeration of copper ore also showed no negative effects on the bacterial populations throughout a leach cycle.

Jan 1, 2007

By G. Langlands

"R. Tenbergen Is this flotation machine suitable in the flotation ofInco ball mill discharges where we have a coarse feed at 60% solids?Reply Experience has shown that there is not a significant increase in the wear life of these machines when handling coarse material (8 mesh) at 60% solids. A common practice in Europe is shut down on the week-ends.The material is allowed to settle and on start-up an injectic of air for 15 seconds is sufficient prior to start-up. At,mining we put our unit in the middle of a bank of 44 cells and in order to ensure severe sanding we shut the aker cell down while the remaining cells kept running. After 20-25 seconds of air the cell started without trouble.P. Mahant Is there a build-up inside the impellor shaft housing? Falconbrige Ltd.Reply There is no sand build-up but rather a scale build-up which due to a flexing action frees itself periodically. Part of the design of the machine permits a water injection into the shaft housing to free any build-up. This is done in Europe during the week-end shut down."

Jan 1, 1984

By Jennifer Young

Presentation Outline ? Introduction ? Aboriginal Inclusiveness ? Common interpretations, practices ? Aboriginal Community Expectations ? Lessons Learned ? Native Code of Conduct Introduction Jennifer Young ? Nestu'et (Mi'kmaq) means: becoming wiser, becoming more knowledgeable Aboriginal Inclusiveness ? Internal hiring strategies (affirmative action) ? Incorporating cultural awareness programs ? Approaches in governmental/organizational policy development Practices in negotiating economic development and fiscal sharing strategies

May 1, 2010

By Gordon R. Peeling

The Problem Five years after the consensus of the Whitehorse Mining Initiative the industry was losing public confidence Public opinion surveys ranked mining just above the tobacco industry Project opportunities were being lost to public and political opposition Operating practices called into question by a number of tailings dam failures CBC broadcast of "The Ugly Canadian" Our social licence was being lost

May 1, 2013

By K. .. Sadayappan

The increasing cost of selenium made the conventional low lead alloys such as EnviroBrasses not economically viable. Efforts were made to develop newer alloys without selenium for plumbing applications. Recently a new copper alloy, C89836, was introduced. This paper discusses the properties of the new alloy including mechanical properties at ambient and elevated temperatures as well as corrosion behaviour.

Jan 1, 2007

By M. A. Kelly

Pit Optimisation using the Lerchs Grossman algorithm has been successfully applied in many deposits. Pit shells often form the basis for scheduling. Pre-assigned costs may not accurately reflect the costs that strategic scheduling decisions are based on. This can affect all mines, but is particularly true for commodities requiring blending. Adoption of Maximiser technology addresses these cost based scheduling and blending challenges.

May 1, 2007

By Benoît Plante

La mine Tio (QIT Fer et Titane Inc.) exploite à ciel ouvert un gisement d?ilménite massive depuis 1950, générant jusqu?à maintenant plus de 70 Mt de roches stériles potentiellement génératrices de drainage neutre contaminé (DNC), dont une partie est submergée dans le lac Petitpas, au nord de la mine. Si généralement l?ennoiement des rejets miniers a un effet bénéfique pour limiter la contamination des eaux, cela reste à prouver pour ce qui est des stériles générateurs de DNC. Des essais en réservoirs ont été réalisés afin d?évaluer la réactivité de trois différents types de stériles submergés, qui ont été choisis en fonction de leur teneur en ilménite. Afin d?évaluer l?impact de la matière organique sur la réactivité des stériles submergés, chaque type de stérile est étudié en immersion simple ainsi que combinée à des sédiments prélevés au lac Allard, à proximité de la mine, d?où l?eau utilisée dans les essais a aussi été prélevée. L?évolution des teneurs en Ca, Mg, Si et Ni durant les 8 premiers mois d?étude démontrent que les stériles immergés sont réactifs, mais l?impact de la matière organique demeure pour l?instant difficile à préciser. Tank tests on Tio mine waste rock The Tio mine (QIT Iron and Titanium Inc.) exploits a massive ilmenite ore as an open pit since 1950, producing over 70Mt of potentially contaminated neutral drainage (CND)-generating waste rocks. While the underwater disposal of mine wastes generally show a beneficial effect on water contamination, this method still needs to be approved for CND-generating waste rocks. Tank tests were realized in order to evaluate the reactivity in underwater conditions of 3 different waste rock types, chosen with regards to their ilmenite content. In order to evaluate the impact of organic matter on the reactivity of underwater waste rock, each waste rock type was studied in simple immersion and in combination with sediments sampled at Allard lake, located near the mine, where the water for the tests was also sampled. The evolution of Ca, Mg, Si and Ni during the 8 first months of testing show that the waste rocks are reactive underwater, but the impact of the organic matter is till hard to define.

Nov 1, 2008

By D. Newman

"This paper discusses the author’s work on international law norms of consultation with Indigenous communities and examines unexpected corporate stakeholder impacts on these norms. Customary international law, which governs the area, does not traditionally refer to corporate conduct. This paper surveys several sources on developing international law on consultation obligations; it also discusses the impacts these norms can have on corporate stakeholders in the mining industry. Finally, it asks how interactions of corporate stakeholders in this area can indirectly impact future law and suggests implications for different business models in the mining sector.RÉSUMÉ Le présent article traite du travail de l’auteur sur les normes de consultation avec les communautés autochtones contenues dans le droit international et examine les impacts inattendus des parties prenantes sur ces normes. Le droit coutumier international, qui gouverne ce domaine, ne réfère traditionnellement pas à la conduite des sociétés. L’article analyse plusieurs sources traitant du développement de nouvelles lois internationales sur l’obligation de consulter; il traite aussi des impacts que ces normes peuvent avoir sur les parties prenantes dans l’industrie minière. Finalement, il pose la question à savoir comment les interactions des parties prenantes dans ce domaine peuvent avoir un impact indirect sur les lois futures et il suggère des implications pour divers modèles d’affaires dans le secteur minier."

Jan 1, 2015

By A. Ingelson, C. Nwapi

"With growing international interest in mineral resources in Central Africa, the importance of transparency in resource development cannot be overemphasized. Without transparency, the region cannot maximize revenues from resources. Although the importance of transparency is beginning to be recognized, many factors can hold back the gains of transparency from resulting in real economic development for the countries involved. This paper reviews current financial, economic, and development literature for Central African countries, with a focus on identifying underlying conditions and specific transactional conditions impacting the effectiveness of transparency in mining development in the region.RÉSUMÉ En raison de l’intérêt international croissant pour les ressources minérales en Afrique centrale, l’importance de la transparence dans le développement des ressources ne peut pas être surestimée. Sans transparence, la région ne peut pas maximiser les revenus tirés de ses ressources. Bien que l’importance de la transparence commence à être reconnue, plusieurs facteurs peuvent freiner les gains acquis de la transparence à produire un véritable développement économique pour les pays touchés. Le présent article analyse la littérature financière, économique et développementale contemporaine pour les pays de l’Afrique centrale, tout en ciblant l’identification des conditions sous-jacentes et les conditions spécifiques transactionnelles qui ont un impact sur l’efficacité de la transparence dans le développement minier de la région."

Jan 1, 2015

By Henry Hengeveld

Are the IPCC results credible? The most recent IPCC assessment is??an admirable summary of research activities in climate science? US National Academy of Science 2001 report to President Bush Joint statement by Academies of Science from 17 other countries ? May 2001 ?The work of the?IPCC represents the consensus of the international science community on climate change science. We recognize IPCC as the world?s most reliable source of information?and endorse its method of achieving this consensus.?

Nov 1, 2002

By H. Ito, T. Takasu

A leaching process for recycling small car motor scraps dismantled from End- of - Life -Vehicles (ELV) was investigated using waste pickling acid in steel work. Steel parts of mortar scraps were leached by waste pickling acid and Cu wire was recovered as pure Cu in the process. Pickling acid solution after leaching could be recycled in an ordinary process for waste pickling acid solution. High grade FeSO4 agent could be produced using H2SO4 as a pickling solution.

Jan 1, 2004