Search Documents

By C. E. Schmidt

Homestake crushing and grinding, practice-was completely revised during the period of 1951-1953. During the conversion, both crushing plants at the head frames the Ross and the Yates, were changes at each plant involved replacing the two 8K gyratories with a rebuilt, The flow sheet single thirty inch gyratory for primary crushing to four inch. The gyratory discharges to a seven foot Symons standard cone crusher set at 1-1/8 inch opening. The cone discharge goes to Tyrock screens fed by vibrating feeders. Screen openings, are l/2 inch by 5 inches: at the Ross. Plant, and 3/8 inch by 5; inches at the Yates. Screen oversize goes to a seven foot Symons cone brusher converted to the short head type; the crusher setting is 5/16 inch. Crusher, discharge; is closed circuited with the Tyrock screens, The above crushing installation delivers a minus 5/8 inch rod mill feed to the mill bins. The crushing revision eliminated the-180 heavy South African type stamps, which had previously reduced the 2 inch crushing plant product to a minus 5/8 inch feed for the 10 rod mills, and 8 ball and pebble.; mills, other revisions in the mill flow sheet, resulted in 3 identical units of about 1350 tons per day, capacity per unit, Each unit consists of an open, circuit 6 foot by 12 foot rod mill, fed from two 24 in by 48 inch vibrating feeders of the four feeders available per unit. A gathering belt delivers the ore discharge of the feeders to the Transportoweigher, which in turn discharge s, into the rod; mill feed spout. Rod Mill discharge is the feed for the 9 foot by 11 foot ball mill, The ball mill is closed circuited with a 16 foot by 30 foot Dorr Classifier. The Homestake make amalgamator, for coarse gold recovery in the ball mill circuit, made' necessary a 36 inch spiral conveyor between the classifier rake discharge and, the combination drum and double scoop feeder on the ball mill See Figure l - the flow sheet of the two stage grinding units.

Jan 1, 1958

By Brain W. Lawrence

Sublevel stoping generally is a large-scale open stoping method. It sometimes is referred to as long-hole or blasthole stoping. This method usually is applied to strong ore bodies that require minimal support and are surrounded by strong country rock. The ore body should be fairly regular in shape and well-defined. The dip of the footwall normally should be sufficient to allow broken ore to gravitate freely, although the method has been adapted successfully to mine some of the flatter ore bodies. Sublevel stoping is not dependent on the width of the ore body. Widths of less than 6 m (20 ft), however, make the utilization of long-hole drilling techniques more difficult. The main criteria for sublevel open stoping are competent ore and stable host rock, regular ore boundaries, and a footwall dip that exceeds the angle of repose of broken ore. Basically, the method entails providing access to the ore body at various subintervals between the main haul- age levels in order to drill and blast the intervening ore. Stope drilling is carried out from drilling drifts on the sublevels, and the ore is blasted in slices towards an open face, which generally is vertical on the downholes and may be inclined towards the open face for the up holes. The blasted ore gravitates to the bottom of the stope and is collqcted through drawpoints. Fig. 1 illustrates a typical sublevel stoping mine. The method requires extensive ore body development with relatively high capital expenditures. How- ever, much of the development is in ore, and production costs are comparatively low. Productivity rates are in the 13.6 to 27.2 t (15 to 30 st)/manshift range. The drilling, blasting, and loading operations are performed independently, and equipment utilization is high. Large outputs can be obtained with few units and limited personnel. Dilution with waste rock may occur if ore boundaries are irregular or if caving occurs, but 100% of the ore within the stope usually is recovered. Pillar recovery sometimes is a problem. It is at this point that most of the waste dilution occurs. At the time data was gathered for this report (1973), the sublevel open stoping method was used by more than 21% of the metallic ore mines in the US (9 out of 42 mines producing 1088 + t/day (1200 + stpd) and provided more than 12% of the total metallic ore production from these mines. DEVELOPMENT Access to a sublevel open stope mine is gained by a slope or shaft that is normally sunk in the footwall of the ore zone, away from any possible effects from blasting or other production operations in the stoping process. Main level interval is selected and usually varies from 45.7 to 121.9 m (150 to 400 ft), depending on the vertical extent of the ore body, the number of drawpoints required to maintain output, and the eventual stope height. The main haulage drifts are located at the bottom of the stope horizon, either directly in ore or in the footwall, with access crosscuts at intervals. Raises are driven up through the ore to connect to the level above and provide access and ventilation to the sublevel drilling drifts, which are driven horizontally in the ore for the length of the stope. Depending on the drawpoint system to be used, the stope is either undercut by a raise-and-cone system, from a scram or slusher drift, or simply provided with a drilling drift from which access is made at intervals to the main haulage level. A raise driven either at the end or in the middle of the stope (if stope access is from both ends) provides a start for opening up a vertical slot across the stope to establish a free or open face for long-hole drilling and blasting. Sublevel stoping has proved to be a relatively safe and economical system.

Jan 1, 1982

By Richard P. Curtin, Madan M. Singh, Francis S. Kendorski

INTRODUCTION The use of roof and rock bolts to reinforce the strata is an established method of rock support in both underground and surface excavations. However, the need to drill a hole, extract the drill-rods, and then place the bolt is time-consuming and costly. This becomes even more significant if the bolting is repetitive and extensive as in coal mining. Though the main thrust of this development was directed towards coal mining, the basic concepts are also widely applicable to all excavations. The authors, therefore, feel that this innovation should be of interest in rapid excavation and in tunneling. In the case of coal mining, it has been established from past statistics that the roof-bolting operation is the most hazardous activity. This is primarily because of the operator being exposed to unsupported ground. It is evident that remote installation of roof bolts would markedly improve the safety of the operation, if accomplished more readily with self-drilling bolts rather than the conventional two-step variety operation. Thus, in addition to increasing productivity, this development can be considered to be a milestone towards further improvements. The objective of this program was to establish the technical and economic feasibility of self-drilling roof bolts for use in coal mines. It might be clarified at the outset that this work was, therefore, directed primarily at showing that workable self-drilling bolts with less cost can be developed, which could be effectively used in mines. It was not to fabricate a production model bolt.

Jan 1, 1979

By Rudolf E. Pfister

One of the Swiss transalpine highways includes two remarkable tunnels: the 16.3 km long Gotthard Road Tunnel and the 9.3 km long twin tube Seelisberg Tunnel, both presently under construction. Large diameter shafts up to 900 m long are required for ventilation. Excavation techniques for rock formations ranging from loose sedimentary rock to granite and very hard siliceous limestone were carefully evaluated. The methods finally applied include excavation of shafts in hard rock, conventional drilling and blasting, excavation by ripper-tooth excavator ("Big John") in marlstone, shield protected heading in loose material and soft rock, and tunnel and shaft lining, both by poured concrete and by prefabricated elements. A critical review of the success of these methods can now be made after a five year construction period.

Jan 1, 1976

By W. H. Andrews

DEFINITION OF BAUXITE The term "bauxite" (1) dates back to 1821, when it was assigned to a deposit of red earthy material outcropping near the village of Les Baux in Southern France. Chemical analysis indicated the presence of aluminium oxide, iron oxide and water. Deposits of bauxite are widespread throughout the world although the major developments occur within 30 degrees of the Equator. Essentially bauxite is the product of weathering and leaching of a variety of sediments or rocks, generally in a high-rainfall tropical or sub-tropical climate, resulting in the enrichment of the aluminium oxide content. It is characterised by the presence of one or more of the minerals, gibbsite, boehmite, and diaspore. The other constituents are usually clay, (typically kaolin), hematite and/or goethite (iron-oxides), anatase (titanium oxide), and possibly silica as quartz. A variety of minor elements may be present, such as calcium, magnesium, phosphorus, vanadium, gallium, manganese, and many others in very small quantities. Organic compounds are normally present from development in association with a soil horizon where vegetation may be encouraged by the high rainfall necessary for bauxitisition. The physical form depends upon the geological history of the deposit and correlation also exists with the mineralogy. Older deposits which have been subject to burial are invariably hard and compact with the alumina predominantly occurring as boehmite or diaspore, while the more recent, surface deposits are frequently less compacted and gibbsite is the dominant alumina mineral. In these later deposits, the physical form can vary from the fine red soil (terra rosa) of Jamaica to the Weipa pisolites to the cemented Arkansas type. The presence of concretionary structures is an important aid in identification in the field.

Jan 1, 1984

By W. A. Lawruk, L. J. Wilson, D. E. Stief

The Tower mill is a vertical stirred mill using steel balls or pebble grinding media. This device is designed for fine grinding at significant power savings when compared to conventional tumbling mills. This paper describes the machine and its operation, application, and performance for wet grinding.

Jan 1, 1988

By J. Smolensky, M. Paul

The Nordhalde is a waste rock pile resulting from uranium mining near Ronneburg, Germany. The pile contains over 27 million m3 of waste rock. Typical seepage water has a pH of 2.7 and a sulfate concentration of 10,000 mg/L. Geochemical investigations of the Nordhalde from 1993 to 1996 included drillholes, test pits, ABA and metals analyses, column tests, and a detailed review of the construction history of the pile. In 1996, eight drillholes were instrumented for monitoring oxygen and temperature. Monitoring continued for a fill year. Hourly temperature and pressure readings were taken by automated data recorder. Oxygen concentrations were measured three times per week, and periodic gas samples were obtained for complete analysis. The resulting data set is believed to be one of the most comprehensive of its kind. Effects noted elsewhere, such as thermal convection, are evident. However, unlike other data in the literature, the NordhaIde data shows a strong seasonal effect, with convection dominating oxygen transport only in the winter months. Analysis of the data allowed the amount of contaminants associated with ongoing and historical oxidation to be compared, and results were used to assess the potential effectiveness of proposed remediation measures.

Jan 1, 2000

By P. C. Schutte, A. J. Kielblock

INTRODUCTION Certain activities, such as emergency work and rescue operations, often have to be undertaken in environments where heat loads often exceed limits prescribed for routine work. This is particularly relevant to the South African mining industry where heat stress-induced fatalities are not uncommon during rescue operations. In this regard an excessively hot environment is defined as one where either the dry-bulb temperature exceeds 37,0°C or the wet-bulb temperature exceeds 32,5"C, and it is therefore not surprising that heat stroke mortality escalates rapidly when these limits are exceeded. A review of both local and international standards indicated that the available information on safe exposure times under abnormal heat stress conditions is very limited. Where available, such standards are aimed at the general population, including both sexes, irrespective of age and also the least heat tolerant worker, and not at a medically-screened, all-male population free of grossly heat intolerant individuals, as is the case in the South African mining industry. It is suggested that available norms and limits are too conservative for local application and, therefore, unrealistic. In view of the definite need to protect workers when exposed to abnormally high environmental temperatures, the present study was undertaken to establish a scientifically derived data base. applicable to local conditions, to determine safe exposure times: Any exposure limit, especially in an emergency situation, should be easy to administer, valid and reliable. These aspects, there- fore, form an integral part of this paper. FORMULATION OF HEAT STRESS LIMITS The formulation of heat stress limits was based on the criterion that a heat exposed individual should experience a negligible risk of developing dangerously elevated body temperatures. In order to provide a database for risk assessment, certain physiological responses of heat tolerant men were determined at various combinations of thermal conditions and work rate in a climatic chamber. These physiological responses were analysed statistically in order to predict safe survival and tolerance times as a function of thermal conditions and work rate. EXPERIMENTAL DESIGN A total of 202 randomly selected, medically fit mine workers volunteered for the study on the basis of informed consent. These men were considered to be inherently heat tolerant in as far as they had successfully completed a heat tolerance test (Anon., 1991) or the standard climatic room acclimatisation procedure used on many South African gold mines (Anon., 1989). The subjects were allocated randomly to 14 experimental groups and each group was exposed in a climatic room to one of

Jan 1, 1997

By Eric Gilmore, Ron Tudor, Gregory E. Korbin, Bill McCormick, Brad Bush

INTRODUCTION Las Vegas has recently been termed the “Construction Capital of the Country”. It has also been acknowledged as the fastest growing city in the country for several years running. The rapid growth improves the economic picture of the region but it also imparts unusual demands on the area’s infrastructure. In 1994 the Southern Nevada Water Authority (SNWA)was working on a master plan to address the rapid growth. A long range analysis revealed the need for additional water treatment capacity and delivery systems. Short term projections showed that the current system would reach capacity in the summer of 1997 with the possibility of demand exceeding the supply. The River Mountains Tunnel #2 is part of a $150M scheme to quickly upgrade the system to meet the short term demand, improve the overall system operation and allow for a smooth transition into the larger additions being planned for the future. The SNWA selected Carollo/Black & Veatch (CBV) to provide detailed design and construction management for the upgrades. The River Mountains Contracts consisted of five separate contracts broken out separately to stream line a very aggressive (just 34 months) design and construction schedule. Necessary work included four miles of excavated and lined tunnel, connections from existing pipelines to and from the new tunnel including large diameter (to 3.66m(144 in)) valves, a 18 927cu m (5 million gal) regulating reservoir, a surge tank and a 170 343cu m (45 million gal) reservoir to add additional storage to the system. Notice to Proceed was given to Kajima Engineering and Construction (Kajima) on May22, 1995 for the construction of the River Mountains Tunnel #2. The design called for a tunnel to be driven 6070m (19 915ft) in rock and lined to a finished diameter of 3.71m (12.17ft).Excavation began on December 14, 1995 and holed through on April 30, 1996. Lining began on June 25, 1996 and a notice of Substantial Completion was issued on December 13,1996. This paper describes the measures taken to complete the tunnel in 18 months from Notice to Proceed to Substantial Completion. THE RIVER MOUNTAINS SITE The River Mountains are a low range of rugged mountains separating the Las Vegas Valley from its main supply of water, the Colorado River at Lake Mead. They are volcanic in origin and the harsh desert environment has left them as expanses of exposed bedrock rising 305m (1000ft) above the valley with little or no vegetation. An existing 3.05m (10ft)

Jan 1, 1997

By A. L. Wilder

Coeur d'Alene Mines Corporation's newest precious metals property is located in the old Rochester Mining District approximately twenty-five miles northeast of Lovelock, Nevada. Built at an elevation in excess of 6 000 feet, the Coeur-Rochester gold silver heap leach property encountered cold weather operational problems typical of most northern Nevada heap leach properties, soon after the start-up of operations last fall. Due to the size of the heap area under leach at Rochester, it was decided that 1 the usual practice of spraying to an "ice field" and waiting for the spring thaw was impractical. Further, the delivery schedule for a solution heating system of the size required was unacceptable. Accordingly, Rochester personnel embarked on a program to seek out a leach solution distribution system that would enable an operation through the winter and yet be cost effective. The findings of this program were rather dramatic and, as a result, the whole perception of heap leach solution application at Rochester has changed forever.

Jan 1, 1988

By Steve Kral

"Gold rush" is usually associated the western United States - California, Nevada, and Colorado. The southeast section of the nation is known more for its rice, textiles, tobacco, indigo, and cotton. This area, though, is where it all began with gold in this country. The United States' first gold rush, in fact, is said to have started with the discovery of a 7.7-kg (17-1b) nugget in the Piedmont section of the Carolinas in 1799, some 50 years before the rush to California. The Carolina gold rush continued intermittently through 1942 when the Federal Government shut down all gold operations. Strong gold prices throughout the early part of this decade and new extractive technologies spurred a small resurgence of gold operations in South Carolina. Mind you, this is not Nevada with its flood of geologists and mining companies. Nor are there any 7.7 kg (17 lb) nuggets being discovered. But Ridgeway Mining Co., a joint venture between Kennecott Corp. and Galactic Resources, has set about mining 51 Mt (56 million st) of low-grade ore containing an estimated 43.5 t (1.4 million oz) of recoverable gold. The open pit, carbon-in-leach operation is located near the town of Ridgeway in South Carolina, about 32 km (20 miles) north of Columbia. Carolina gold North and east of Ridgeway, Piedmont Mining Co. operates the historic Haile gold mine near Kershaw, SC. And Brewer Mining Co. operates the nearby Brewer deposit. Between 1829 and 1942, South Carolina gold mines produced 10 t (318,800 oz) of gold. It all began in 1799 when Conrad Reed, son of a German immigrant farmer, found the 7.7 kg (17 lb) nugget in Little Meadow Creek, NC. His father thought the rock was worthless and used it as a doorstop, so the story goes. It took nearly three years before Conrad's father decided his doorstop was indeed gold. Gold was later discovered in the Greenville district of South Carolina. And, in 1828, Benjamin Haile discovered gold in a stream that ran through his property in Lancaster County, SC. Haile's mine became South Carolina's most famous and most productive gold mine, producing more than 7.8 t (250,000 oz). At first, miners worked the stream beds of Haile's property. Later, lode deposits were discovered on slopes alongside the creeks. They would lease 4.6 ml (50 sq ft) lots and mine as deep as 7.6 m (25 ft). During the Civil War, the Confeder-

Jan 1, 1989

By F. Michael Wahl

With the exception of reports on commercial deposits of kaolin, fuller's earth, and other specialty type clays, there is little published information on the extent, properties, and potential uses of the clay resources of Florida. Recent studies by the Florida Bureau of Geology in cooperation with the University of Florida and the U.S. Bureau of Mines have proven the existence of two extensive Miocene clay deposits, one in peninsular Pinellas County and the other in southeastern Charlotte County. Drilling and subsequent testing of the clays from these deposits indicate their potential for economic development. Both deposits consist of montmorillonite type clays, have an average thickness of 25 to 35 feet, and are overlain by unconsolidated Pleistocene sediments. Preliminary firing tests indicate that the clays from Pinellas County are a potential raw material for lightweight aggregate production. The clay has good bloating characteristics across an acceptable temperature range with a resultant aggregate density of less than 1.00 specific gravity. The clays from Charlotte County have poorer natural bloating characteristics but might well be used after treatment or with additives. The economic potential and locations of both deposits emphasize the need for locating similar clay resources in the state that might have economic potential so that land use planning and subsequent urbanization will not prohibit their development.

Jan 1, 1972

By D. D. Murphy

The Bureau of Mines has studied the mechanism of shear-flocculation of silica with stearic acid. At pH 6 and 12, shear-flocculation of silica was not observed with up to 10-4M (5 lb/st) stearic acid. However, in the presence of 0.1 M NaCl at pH 6, shear-flocculation was observed at stearic acid concentrations 10-4 M (5 lb/st). Adsorption of stearic acid on silica was studied using stearic acids spin-labelled with a doxyl group. The presence of the spin-labelling group did not greatly affect the shear-flocculation properties of stearic acid. Adsorption of labelled stearic acid on silica was measured as a function of surfactant concentration with electron paramagnetic resonance (EPR) spectroscopy and gas chromatography (GC). The GC results indicate the stearic acid was predominately adsorbed on the surface at concentrations above 10-4 M. From the EPR spectra, the formation of aggregates of stearic acid was apparent at concentrations of approximately 10-414 (5 lb/st). The results are discussed in terms of a possible mechanism for shear-flocculation.

Jan 1, 1993

By D. Loy LeRoy

As we are all aware, the impacts of the 1977 Surface Mining Act and the implementing OSM Regulations require application of new, as well as existing, equipment and technologies. Our firm recently completed (June, 1979) a study for the Department of Energy titled "Analysis of the Impact of Public Law 95-87 on Mining Performance." The objective of the study was to analyze the impact of the Act and its regulations on mining performance in order to provide recommendations to alleviate the impacts identified, including identification of research needs. This paper presents some of the highlights of that report: projected cost increases; additional equipment needed for compliance; review of methods currently practiced or those which can be modified; and will focus particulary on equipment and technology applications.

Jan 1, 1980

By William R. Groseclose, Cecil E. Tackett

Since 1965 when the first mole was used on Bureau work, the Bureau of Reclamation has completed 17 tunnels of over 5,000 feet in length. The longest was 12.8 miles. Total length of the 17 tunnels was 376,207 feet, or over 71 miles. The finished diameter varied from 7 feet 0 inch to 18 feet 0 inch with 82 percent (58 miles) being less than 12 feet 0 inch in diameter when lined. All of these tunnels except one are gravity flow, water conveyance tunnels with relatively flat gradient. One is a low-head pressure tunnel. All were constructed by contracts resulting from fixed-price bids. Starting in 1964 the Bureau of Reclamation initiated the practice of giving several options in the specifications on methods of tunnel excavation. Since that time, construction work has been completed on 17 tunnels. Of this number, 11 were mole excavated and 6 were excavated by conventional drill and blast methods. In general, there has been 2 feet of mole excavation for every 1 foot of drill and blast. Cost comparisons are based on only 13 tunnels because the Bureau has 4 recently completed tunnels that have pending claims; therefore, final cost data are not available. Some definite trends show from the data available; however, the number of completed tunnels in some categories is so small the results cannot really be considered a trend. As more data become available, the indications will become more reliable. The information is presented to indicate general trends and comparisons and cannot be meaningfully used for a one-on-one comparison because of individual tunnel differences not considered.

Jan 1, 1974

By R. D. Hagni

Introduction The ore deposits of the Viburnum Trend in the Southeast Missouri Lead District constitute the world's largest lead producing district. Six or seven mines currently are in production in the Viburnum Trend. The principal minerals are few in number, simple in composition, and form simple superposition and replacement textures. The economically valuable minerals in the typical lead-zinc ores of the Viburnum Trend are the sulfides, galena, sphalerite, chalcopyrite, and siegenite. The most abundant gangue minerals are dolomite, marcasite, pyrite, calcite, quartz, and dickite. Four concentrates, lead, zinc, copper, and cobalt are produced from the ores, and they contain an interesting suite of trace elements, of which silver and cadmium are recovered at the smelter and refinery.1 Emphasis is given here to the variations in directions of ore fluid flow based upon interpretations of the positions of orebodies due to the ore fluids being impeded by Precambrian basement relief and upon patterns of ore mineral/metal zoning. The Precambrian basement relief and Lamotte Formation pinchout has exerted an important control upon the specific locations of orebodies in the Southeast Missouri Lead District. The locations of some orebodies along one side of Precambrian knobs or ridges strongly suggests that they are positioned on the side from which the ore fluids flowed. Other orebodies are located in positions that suggest that they formed where the ore fluids passed around or between Precambrian knobs. Patterns of mineral and/or metal zoning have been used in many mineral districts to interpret the directions of ore fluid flow. The mineral/metal zoning pattern correlates closely with that of the mineral paragenesis. The earliest deposited minerals tend to be deposited nearest to the source, the later deposited minerals next closest to the source, and the latest deposited minerals furthest from the source. In the Southeast Missouri Lead District, it is interpreted here that the early-deposited copper-rich ores are closest to the source of the ore fluids, the subsequently-deposited zinc-rich ores are next closest to the source, and iron-rich ores are furthest from the source.

Jan 1, 2006

By W. Holding

Since the 1975 International Mine Ventilation Congress in Johannesburg there has been a trend in South Africa towards making the mine ventilation departments responsible for monitoring the total environment. This includes the taking of noise and illumination measurements and there is in fact a debate taking place as to whether the departmental title should be changed to 'Environmental Control Department'. The organisers of the 2nd international Mine Ventilation Congress have decided that noise and illumination will not be included as Congress subjects and 'Total Environment' includes only those facets which are open to debate at the Congress. The choice of mine is significant in that while most Congress papers from South Africa will be devoted either to coal mining or to the somewhat unique deep level gold mines, Prieska Copper Mine is a mine which can easily be identified with similar mines in many other parts of the world. The mine is situated some 750 km south west of Johannesburg and about 600 km north east of Cape Town. Current production (ore and waste) is about 340 000 tons per month and the total underground labour force is just over 2 000. The ore body is a massive sulphide, the main minerals being copper and zinc and the method of mining is sub-level open stoping. Daily average surface temperature conditions range from 85°F (29.5°C) dry bulb and 69.8°F (21°C) wet bulb in mid-summer to 42°F (5.5°C) dry bulb and 36.5°F (2.5°C) wet bulb in mid winter. The information presented in-this paper is limited to what can be gathered by mine ventilation staff as part of an on-going exercise and is obviously not as comprehensive as would be the case if a fully equipped research establishment were to become involved. The paper will be divided into three sections 1) Gases 2) Dust 3) Heat In each section statutory and/or other standards will be set down followed by a discussion of assessment and in some cases control methods.

Jan 1, 1980

By R. G. Reddy, A. E. Torma

Bio-treatment of uranium contaminated soils from Fernald using the bacterium Thiobacillus ferrooxidans was investigated. The experimental results showed that extraction of uranium upto 99 percent from soils were obtained with 10 percent pulp density suspension and with addition of iron (3000 mg/l) after bio-remediation time of seven days. Application of the results to industrial practices is discussed.

Jan 1, 1995

By John Duff Erickson

Determination of the final pit limits of an open pit copper mine is a problem that has far reaching effects on the life, profitability and operation of a mine. The solution to this problem requires that all of the significant variables affecting the final pit limits be considered together with corporate objectives as the guiding principle. This paper discusses the use of these variables and how they should be applied to plan the future of a mine. The objectives of a final pit plan; are determination of the extent and location of ore reserves, the allowable stripping to be accomplished to uncover the ore, the final pit surface intercept, final pit topography and the contained metal values in both ore and waste. The objectives of the plan must be consistent with corporate objectives as they pertain to profit, future investment in the mine, return on investment, alternative investments, conservation and perpetuation of the corporate entity. The subject will be treated in three parts: economic considerations, effect of leaching and pit design technique. At the outset, it is assumed; that the extent of and metal values in the mineralized area to be considered have been reasonably defined by development drilling and sampling.

Jan 1, 1968

By Clayton J. Parr

Introduction This chapter contains brief discussions of various environmental protection requirements that relate to underground mining operations. Environmental disturbances at an underground mining operation can result from subsidence; water discharges; waste dumps; construction and operation of access roads and utility lines; construction and operation of surface facilities such as maintenance shops, bathhouses, and storage yards; and emanation of dust and noise from surface crushers. Construction and operation of a concentrator or washing plant may result in the emission of air pollutants, the discharge of water pollutants, the creation of noise, and disturbance of the surface. Tailings ponds can be the source of fugitive dust.1 This chapter is not intended to provide a detailed discussion and analysis of laws and regulations dealing with environmental protection. Rather, its purpose is to provide the engineer with a basic awareness of the existence and nature of such laws and regulations, as well as the procedural requirements that must be followed in complying with them. The body of law relating to environmental protection has grow" very rapidly and should continue to do to for some time. Because many of the laws have been enacted recently, numerous court decisions are being rendered to resolve disputes over their interpretation. Hence, the reader is cautioned to be alert for subsequent modifications of statutes and regulations, and new case law. Rules and regulations pertaining to environmental protection are implemented at all governmental levels. The most widely known laws are those enacted by the federal government that have nationwide applicability. However, separate requirements exist in each state, county, and municipality. Because of their general applicability, federal laws are discussed most extensively in this chapter. Ownership of the property is the most significant factor considered in ascertaining what rules govern the conduct of an operation thereon. If the land is held under lease, reference to the lease terms must be made in the first instance to determine what obligations must be met in order to prevent default and possible loss of the property. If the land is held under a lease from the federal government, the operator is subject not only to compliance with the lease terms, but also to a large body of laws and administrative regulations that pertain generally to the conduct of mining operations on land held under federal leases. Although operations on unpatented mining claims, the legal title to which remains in the federal government, are not subject to the same rules and regulations that are applicable to operations conducted pursuant to federal leases or permits, they soon will be governed by a special set of regulations that provide for protection of surface resource.2 Operations conducted on lands leased from a state usually are subject to numerous environmental protection requirements specified in the lease terms, in addition to rules and regulations promulgated by the state agency having jurisdiction over mining on state lands. Operations conducted on privately held lands are subject to fewer such requirements. Leases from private parties sometimes have environmental protection and reclamation requirements written into them, but generally to a far lesser extent than governmental leases. Operations conducted on properties owned by the operator are subject only to those laws and regulations that have general applicability without regard to land ownership. COAL SURFACE MINING CONTROL AND RECLAMATION ACT OF 1977 Introduction On Aug. 3, 1977, the Federal Surface Mining Control and Reclamation Act of 1977 was signed into law.3 It governs coal-mine operations on private lands, as well as on public lands. The Act is pervasive in its scope and is extremely long and complex. The basic purpose of the Act is to control and minimize the environmental effects of surface coal mining. Surface coal-mining operations are defined as activities conducted on the surface of lands in connection with a surface coal mine and surface impacts incident to an underground coal mine.4 The Act is administered by the Secretary of the Interior through a new agency named the Office of Surface Mining Reclamation and Enforcement.5 The Act contains detailed environmental protection standards and reclamation requirements, and it establishes a permit system for all surface coal-mining operations. Mining in certain areas and under ceri-in conditions is restricted or prohibited, and a mechanism for enforcement by the states is provided. Stiff penalties are provided in the event of noncompliance. Implementation Schedule Nonfederal Lands: As required by Section 501 of the Act, interim regulations setting mining and reclamation performance standards based on and incorporating standards set out in Section 502(c) were adopted effective Dec. 13, 1977.6 They will. be incorporated as amendments to Chapter VII of Title 30, Code of Federal Regulations. Permanent regulatory procedures for surface coal-mining and reclamation operations performance standards, which were directed to be promulgated by Aug. 3, 1978, were published in proposed form on Sept. 10, 1978. 7 They govern surface coal-mining operations in any state until a permanent state or federal program is adopted. As of Feb. 3, 1978, all new operations, and as of May 3, 1978, all existing surface coal-mining operations, on lands on which such operations are regulated by a

Jan 1, 1982