Search Documents

Report of Secretary TO THE BOARD OF DIRECTORS OF AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen -I have the honor to present the following report for the calendar year 1920 The activities which-seem to call for special com¬ment are THE NEW FORM OF MAGAZINE MINING AND METALLURGY appeared every month during the calendar year and has been developed until it contains some ten departments It has brought forth more commendatory letters than have been received at headquarters on any other subject throughout the year Less than a dozen letters unfavorable to the change have been received, and the indications are that the magazine has met a want deeply felt, especially by members distant from headquarters The technical papers printed by the Institute are published in abstract in the magazine and opportunity is given to members who desire them to receive full copies of any or all papers published The Bound Volumes, as usual, contain all the papers in full and discussions thereof FINANCES The greatly increased cost of paper and printing has put a tremendous burden on the Institute's finances, since the dues of $12 per year are only 20 per cent greater than the members paid when the Institute was founded forty-nine years ago This has resulted in a temporary deficit, similar to that encountered by many of our sister engineering societies The fact that our Institute has lower dues and gives more in the way of publications to its members than any other of\the national engineering societies has rendered the situation more difficult for us MEETINGS The Annual Meeting in New York, the Field Meeting in the Lake Superior District, the meeting of the Petroleum and Gas members at St Lours, and of the Institute of Metals Division in Columbus, Ohio, have all been described in full in the magazine

Jan 1, 1923

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By E. A. G. Colls

IN all branches of the chemical industry, corrosion plays a very costly part unless it is suitably com-batted, and as a result it is probably correct that chemical and design engineers are more corrosion conscious in the field of chemical industry than in others. Most metals occur in nature in combination with other elements. The refined or reduced state to which man converts them for his use, by removing the combining elements, leaves them in an unstable condition. Therefore in most of the media to which the metals are exposed they are constantly combining with the constituents of their environment, or in other words they are continually being corroded. Similarly, nonmetallic materials are corroded by undergoing chemical change. The rate at which corrosion takes place varies widely from metal to metal and medium to medium. In practically all cases the corrosion of metals in solutions (electrolytes) is electrolytic in nature and the rate of corrosion is dependent on many factors such as temperature, pressure, internal stresses, galvanic action, metal-ion concentration, and so on. In the chemical industry substances must be handled which are particularly corrosive to materials of construction. At the chemical plants of The Consolidated Mining and Smelting Co. of Canada, Ltd. (otherwise known as Cominco), situated at Trail, B. C., Canada, the following are some of the materials that have to be handled: Gases. Sulphur dioxide, sulphur trioxide, carbon dioxide, carbon monoxide, oxygen, hydrogen fluoride, ammonia, hydrogen sulphide, and oxides of nitrogen. Liquids. Solutions of ammonium sulphate, ammonium sulphite, ammonium nitrate, caustic soda and potash, sulphuric acid, nitric acid, hydrofluo-silicic acid, hydrofluoric acid, phosphoric acid, aqua ammonia, and formic acid. Solids. Gypsum (containing phosphoric acid), ammonium sulphate, ammonium nitrate, phosphate rock, caustic soda, potash, and phosphate fertilizers.

Jan 1, 1951

By N. F. Fiore, M. F. McGuire

THIS communication describes a series of experiments in which dislocation etch pitting was used to ascertain the depth of damage in crystals which were mechanically polished or which were cut with either a commercial metallographic cut-off wheel,* a com- All specimens were cut from single crystals of American Smelting and Refining Co. 99.999+ pct pure copper which were grown from the melt by the Bridge-man technique. The test specimens were disks, with faces being (111) planes and the disk axis a (111) direction. The disks were annealed in a vacuum of 10-5 Torr for 24 hr at 950°C prior to cutting or polishing and were given a light electropolishing in an ortho-phosphoric acid bath before etch pitting. Both Youngs1 and Livingston's2 reagents were used for etch pitting and the reagents gave identical quantitative results; however Livingston's reagent produced less staining and so all photomicrographs shown are of {111) surfaces etched with this solution. The surface of the annealed crystals showed well-defined subboundaries and a density of dislocations of about 1 X 106 per sq cm excluding those present in subboundaries, Fig. 1. The depth of cold work produced during mechanical polishing was determined after an annealed specimen was mounted in a paraffin holding block to protect it from extraneous damage. The exposed (111) surface was ground on metallographic papers and then polished on billiard cloth through 0.05-p alumina abrasive. It was necessary to remove about 0.3 mm (-0.01 in.) to obtain a structure representative of the annealed sur- face, indicating that the crystal was damaged to this depth during mechanical polishing. The cold work caused by standard cutting methods was measured in another series of tests in which cuts

Jan 1, 1967

By Walter F. Gries

AN ounce of prevention is worth A a pound of cure' is an old proverb that has sometimes been forgotten in programs having to do with the health of workmen. Realization of the truth of this maxim is increasing, however, and today the iron-mining industry, with which I am particularly concerned, is becoming more alive to the prevention of illness and the conservation of health, thus decreasing the need for treatment after diagnosis has established its necessity. The healthy workman is the happy, efficient workman, and new programs tending to make him more health-minded are being put into operation. Preventive medicine is less costly than corrective medicine, to say nothing of the better results obtained. Periodic physical examinations, with close follow-up attention when required, have reduced the time lost because of illness, workmen's compensation costs, and group-insurance benefits for nonindustrial disabilities.

Jan 1, 1939

By William Fink

Two of the aluminum-alloy systems previously studied-the alumi-num-titanium and the aluminum-chromium-exhibit a peritectic reaction at the extreme aluminum end of the diagram. Preliminary work indi-cated that the aluminum-zirconium and certain other aluminum systems were similar in this respect. The present paper, the twentieth of a series from the Aluminum Research Laboratories, reports the results of a recent investigation of equilibrium relations in aluminum-zirconium alloys of high purity, which confirm the preliminary observations. PREVIOUS INVESTIGATIONS There has been only one investigation of the aluminum end of the aluminum-zirconium system. Sykes1 prepared and studied alloys containing 0 to 70 per cent Zr. The lowering of the freezing point of aluminum by the addition of zirconium was found to be very little, if any (less than 2°C.). He placed the solid solubility of zirconium in aluminum at room temperature between 0.57 and 0.97 per cent. A few other investigators have attempted to determine the com-position of the intermetallic compounds occurring in this system. Hönigschmid2 obtained the compound ZrAl3 as a by-product during the preparation of ZrSi2. He made no attempt to prepare other aluminum-zir-conium compounds. Weiss and Newmann3 prepared an alloy by heating aluminum with a double fluoride of potassium and zirconium. When this alloy was treated consecutively with caustic soda and hydrochloric acid, there was a residue, which contained approximately 72 per cent Zr and 28 per cent Al (Zr3Al4). Marden and Rich4 prepared an alloy in the same way, treated it with caustic soda, and obtained a residue of silver-white crystals, which contained 70 per cent Zr and 30 per cent Al (Zr3Al4).

Jan 1, 1939

By W. J. Heck

The need for a better understanding of the effect of fluid pressure on the strength of intact and jointed rock has long been recognized. The behavior of pore fluid pressure was first pointed out by Terzaghi 1 who suggested the application of the effective stress concept to rock and concrete. While the effective stress concept has been used for some time in the design of mass concrete dams, it only recently has been applied to rock. Robinson 2 and Handin et al.3 evaluated the effects of pore pressure on a variety of sedimentary rocks and demonstrated the validity of the concept. Work using pore fluids other than water has been done by Boozer, et al.4 who considered strain rate and temperature as additional variables. According to the effective stress theory, the effective stress, [a], is the difference between the total stress, [a], and the pore pressure, u, and is the controlling factor influencing frictional strength of rock, other parameters remaining constant. Assuming the Mohr-Coulomb failure criteria applies, the shear strength, T, is given by the equation [r=d+ (a-u)tan ¢](1) where [~F], the angle of internal friction, and c, the cohesion intercept of "no load" shear strength, are the effective stress parameters.* Robinson,2 Handin,3 and others have demonstrated that moderately porous sand-

Jan 1, 1972

By H. A. Wriedt

At 500°C (932°F) the range of y' iron nitride is from 5. 77 + 0.03 wt pct N (in coexistence with a iron) to 5.88 * 0.03 wt pct N (in coexistence with E iron nitride). Stoichiometric "Fe,N" (5.900 wt pct N) is near the upper extreme of possible compositiom. The depe-dence of nitrogen activity (expressed as pnh,/Ph,) on nitrogen content is described satisfactorily by a "Langmuir" isotherm: At even the highest nitrogen concentrations, less than 0.18 pct of' the nitrogen atoms present are impositions of disorder. Past investigations1-4 of the Fe-N system have left only details of the thermodynamic behavior of the y' nitride, "Fe,N9', to be studied. The present investigation was made to establish more precisely than hitherto the limits of composition and the relation between composition and nitrogen activity at 500°C. EXPERIMENTAL TECHNIQUE The compositions of nitrides in equilibrium with various NH, + Hz mixtures at 500°C were determined from the weights gained by 0.02-in.-thick (4.0 to 4.5 g) strips of purified iron* when the nitrides were formed A description of the gas generation and furnace system has been published.5 Cracking and blistering during conversion of the original solid iron at 550°C injected considerable porosity into the strips without causing their disintegration. The time for complete conversion was significantly lowered by periodically reducing partly nitrided specimens in hydrogen and then reexposing them to the nitriding gas. Gas mixtures producing single-phase were used in the equilibrations at 500°C. Equilibrium was regarded as existing when the specimen weight was not detect-ably affected by further exposure to the same conditions. The gas compositions and nitrogen activities at which y' transformed to a iron (lower activity limit) and to E iron nitride (upper activity limit) were redetermined during the investigation. A specimen was equilibrated in an NH, + Hz mixture at 500°C and then exposed to a s1ightly different gas. When equi- librium had been reestablished the gas was again changed slightly. At each stage of this repeated process, while the specimen was reacting with the gas, the variation of its weight with time was observed. The onset of phase transition was marked by an abrupt change in the amount and rate of weight gain or loss. The specimens were weighed outside the furnace, in air and at room temperature, on a balance with 0.05 mg precision. When it was found that the specimens were oxidizing at a significant rate during the weighing, a series of timed weighings was made with each specimen, starting 1 min after its exposure to air. RESULTS AND ANALYSIS The gain in specimen weight from oxidation during weighing was linear in the logarithm of time between 1 min and about 2 hr, Fig. 1, later becoming linear in the cube root of time. In the logarithmic period, nitride specimens oxidized two to three times as fast as

Jan 1, 1970

By Hewitt Wilson

IN 1903, T. M. and E. H. Alvord, of Marblemount, Wash., built a soapstone-grinding mill in the Skagit River Valley and are reported to have produced "ground talc" during 1904 and 1905, shipping to the paper mills in Wisconsin. Between 1916 and 1920, the Western Talc Co. built and operated a talc-grinding mill north of Mondovi, on the banks of the Spokane River, in eastern Washington, and sold powdered talc to the Inland Empire Paper Co. of Spokane. ? The most active develop-ment in recent years has been by two companies in the Skagit Valley-the Skagit Talc Company, Inc., which has been sawing soapstone block for the soda-recovery furnaces of the pulp and paper companies, and the Asbestos-Talc Products of Washington, Inc., at Burlington, which has been mining and dry-grinding a soft serpentine for the structural filler and insulation trade. Many prospects have been opened in the northern part of the state on both sides of the Cascade Mountains, and these activities undoubtedly are the forerunner of an industry that promises to attain considerable magnitude in the North Pacific States. At the present time, talc is imported from California for use as paper filler, and soapstone block from Virginia for use in the soda-recovery furnaces. A small market has been created locally for tailor and foundry:, pencils, stove grills, and block soapstone for art objects. The results of the present study, as yet incomplete, indicate that the use as a refractory and as a ceramic filler and flux can be expanded.

Jan 1, 1936

By W. G. Matteson

The origin of the salt domes of the Gulf coastal plain has been investigated by many of the most able geologists, but the problem cannot be said to have been satisfactorily solved. Since 1860, numerous theories have been presented, only to be discarded, at least in part, as more complete infomation revealed their fundamental weakness. Real progress toward solution dates from 1902, when Hill1 advanced the theory of secondary deposition of the domal materials from saturated solutions of hot saline waters ascending from great depths under hydrostatic head along structural lines of weakness. Shortly thereafter, Harris,² using Hill's hypothesis as a basis, explained the doming and pronounced uplift associated with these salt cores as the result of forces exerted by growing salt crystals. This was a marked advance over the ideas of Coste3 and Hager,4 since no evidence of igneous intrusives, as they assumed to explain the uplifts, had been found associated with the domes. Harris5 developed his theory until it offered such apparently plausible explanations of so many details of dome phenomena that his hypothesis and conclusions received widespread acceptance, despite some serious objections, and today his theory, somewhat modified, is considered by many able investigators to be the best explanation of the origin of these domes. The immense production of oil per acre, the recognition of the high lubricating quality of the oil, the development and recognition of the efficiency and advantages of oil-burning vessels, with the subsequent exceptional demand for fuel oil, and the resultant advance in the price of coastal crude, have been responsible for a prospecting and develop- 1 Robert T. Hill: Beaumont Oil Field with Notes on Other Oil Fields of the Texas Region. Jnl. Franklin Inst. (1902) 164, 143. 2Gilbert D. Harris: Rock Salt in Louisiana. Louisiana Geol. Survey Bull. 7 (1907) 76. ³E. Coste: Volcanic Origin of Natural Gas and Petroleum. Jnl. Canadian Min. Inst. (1903) 6, 73. 4Lee Hager: Mounds of the Southern Oil Fields. Eng. & Min. Jnl. (July 28, 1904) 78,137, 180. 6Gilbert D. Harris: Geologicel Occurrence of Rock Salt in Louisiana and East Texas. Econ. Geol. (1909) 4, 12.

Jan 1, 1921

By D. C. Seidel, M. C. Fuerstenau, R. J. Roman

The existence of a surface charge on the alkali halide salts is shown, and a flotation mechanism involving surface charge and collector solubility is developed. Data suggest that KC1 is positively charged and that NaCl is negatively charged in saturated brines, and that the neutral molecule RNH,Cl is the collector in the amine-KC1 system, RSO, is the collector in the sulfonate-KC1 system, and RCOONa) is the collector in the fatty acid-NaCl system. A number of hypotheses have been advanced to explain the mechanism of soluble salt flotation; one of these involves exchange between collector ions and surface cations. With this mechanism Gaudin1 suggested that the differences in flotability of halite and sylvite with primary amines are due to the ionic size of the RNH;, Kt, and Na t ions. Fuerstenau and Fuerstenau expanded this hypothesis to include many other alkali halide salts. Several exceptions to this hypothesis are known. That is, this model does not explain why salts containing the same cation, or why salts of different degrees of hydration, respond differently to flotation. For example, why NaI is floated with an amine whereas NaI .2H,O is not. Further, no correlation between ionic size and flotation response can be made with sulfonate or car-boxylate as collectors. In addition, this hypothesis does not explain the effect of magnesium or lead activation, nor does it offer any explanation of the role of temperature in salt flotation. Rogers and Schulman3 realized some of the inadequacies of the ion exchange mechanism and proposed another mechanism based on the heat of solution of the salts. They concluded that weakly hydrated salts can be floated with alkyl amines and sulfonates, that strongly hydrated salts can be floated with fatty acids, and that excessively hydrated salts cannot be floated at all. Their work was not limited to the al-

Jan 1, 1969

By N. A. Gokcen

The construction and operation of a simple and accurate vacuum-fusion apparatus are described in detail. Absolute accuracy of the oxygen analysis has been determined by the reduction of oxides weighed to 20.01 mg. The Bureau of Standards steel samples have been analyzed repeatedly, and their inadequacy for the acceptable range of oxygen is presented. The limits of interference of manganese, aluminum, and titanium, and the effects of tin and water-cooling of the furnace tube have been investigated in detail. ANALYSIS by the vacuum-fusion method consists of melting a sample in a degassed graphite crucible under high vacuum and extracting oxygen as carbon monoxide, and nitrogen and hydrogen as gaseous elements. The resulting gas mixture is analyzed for its constituents, from which oxygen, nitrogen, and frequently hydrogen may be determined within 1/2 hr or less. The history and summary of methods1-4 and extensive reviews of literature'.' for the determination of gases in metals have been published in detail. The foundation of the modern vacuum-fusion method of analysis was laid by Jordan and Eckman,11 and Oberhoffer and his associates.1, 10 Diergarten,11, 12 Meyer,13 Thanheiser et al.,14, 15 Ericson and Benedicks,16 Ziegler,17, 18 Sloman,16-23 Thompson et al.,24 and later many others contributed to the improvement, accuracy, and limitations of the method. In some investigations, however, the limitations of the procedure and the errors involved in the analysis require further critical examination and evaluation. In many apparatuses, lunnecessarily complicated and cumbersome features and elaborate precautionary measures do not have conclusive advantages. The purpose of this invest:igation was, therefore, a) to construct a very simple and accurate apparatus, b) to determine the absolute accuracy of results, c) to establish the limits of interference of manganese. aluminum, and titanium, d) to reexamine critically the reduction and recovery of oxygen from oxide powders of various sizes, and e) to evaluate critically the eight steels of the Bureau of Standards."' Apparatus The apparatus used in this investigation is shown in Fig. 1. It has been used for over three years, during which several modifications were made. A brief description of the apparatus is as follows. The transparent silica or Vycor tube, E, is joined to the Pyrex head, B, by mean of a face to face ground joint sealed with mercury. A similarly sealed ball and socket joint would also have been satisfactory. A standard tapered ground joint, successfully used by some investigators, was tried, but in the absence of grease or vacuum cement it was very difficult to disassemble the joint. The graphite crucible, G, 15/16 or l 1/8 in. OD, 2 1/2 or 3 in. high, 1/10 in. wall, shown enlarged in Fig. 3a, is made from the rods containing less than 0.08 pet ash. Two baffles, overlapping sufficiently to prevent spattering, are inserted in two opposite slots cut on a band saw. Two small holes in the baffles permit the temperature measurement of the melt. A second type of crucible, Fig. 2, G, shown enlarged in Fig. 3b, is also satisfactory, though not as convenient as the crucible shown in Fig. 3a. Somewhat similar but more elaborate crucibles with baffles were first tried by Ericson and Benedicks,'" but were abandoned in favor of a crucible with a stopper and a peripheral graphite powder filter. Various versions of their crucible with a stopper have later been used by other analysts, 10-27, 27-30 The crucible is packed directly in E, Figs. 1 and 2, with —35 + 48 graphite powder for shielding and insulation. A minimum layer of 7 mm of powder is necessary for keeping E cool and minimizing the blank. The first use of graphite powder was made by Sloman,10-23 Who found that —200 mesh was the most satisfactory. The author tried various size powders from +20 to —100 mesh and found that a) particles of 28 mesh or larger were not sufficiently insulating and were heated by the induction current, b) the powder finer than 60 mesh packed too much and did not readily permit the escape of gases even when the crucible was heated very slowly; hence, the powder was occasionally blown out of the side in the crucible and in the mercury pump. The optimum size powder is, therefore, 35 to 48 mesh size or 0.4 mm in average diameter. The furnace is designed to eliminate excessive amounts of

Jan 1, 1959

By C. R. Ince

THE term "differential flotation" is used to denote a flotation operation in which separation is effected between two or more minerals of the same class; e. g., lead sulfide from zinc sulfide, pyrite from blende, chalcopyrite from pyrite, chalcopyrite from blende. At present, so far as published work shows, there seem to be two theories as to the mechanics of differential flotation. The earlier and more generally accepted theory is that the so-called depressing agents alter the surface of one or more of the sulfides in the ore, either by chemical action or adsorption, so that it is no longer amenable to flotation, but that these depressed sulfides can be revived, after the unaffected sulfide has been floated, by reagents which react chemically with the altered surface and make it amenable to flotation. More recently, Professor Taggart1 has advanced the theory that slime adsorption is an important factor in differential flotation. He believes that, with the proper use of a class of agents, which he calls .dispersion agents and which include practically all the depressing agents, one can cause the slime to adsorb differentially on sulfide surfaces. A gangue-slime coated sulfide surface will act as a gangue particle and will not float. If, subsequently, an agent that will remove the gangue-slime coating is added, the sulfide again assumes its original surface and can be floated as an ordinary sulfide. This-is the basis of the slime theory of differential flotation. Timber Butte mill at Butte, Mont., is a typical lead-zinc flotation concentrator. Neihart ore, chosen for investigation in this work, is one of the custom ores treated at that mill. Practice at Timber Butte mill in February, 1928, was as follows: A combined lead-zinc concentrate was first made using 0.2 lb. per ton on the ore of potassium xanthate and 0.03 lb. per ton of Cleveland Cliffs oil after 1.5 lb. per ton of lime and 1 lb. per ton of calcium chloride has been added just before the ball mill. The concentrate was then thickened to 70 per cent. solids. Potassium cyanide to the amount of 0.3 lb. per ton and zinc sulfate in the quantity of 0.5 lb. per ton were added to the thickened pulp and the whole

Jan 1, 1929

By J. Waldman, M. B. Bever, A. K. Jena

The heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of one solid solution have been measured by tin solution calorimetry. The heats of formation are analyzed in terms of the quasichemical theory. If the enthalpy diffel-ence between a hypothetical fcc form and the hcp form of cadmium is taken into account, this analysis does not lead to the conclusion put forth in the literature that electronic effects make significant contributions to the heats of formation of silver-rich Ag-Cd solid solutions. The temperature dependence of the heats of formation is appreciable and negative near 78ºK, but decreases gradually to nearly zero abore 400°K. The relative partial enthalpies per grarn -atom of silver at 541°K and cadmium at 532" and 541°K in tin have also been determined. THE composition range of the silver-rich Ag-Cd solid solutions stable at room temperature extends to about 40 at. pct Cd. Heats of formation of these solid solutions at 308" and 723°K have been measured by solution calorimetry.1,2 Heats of formation for an average temperature of 800°K have also been calculated from vapor pressures.2,3 The heats of formation deviate from the values predicted by the quasichemical theory above about 30 at. pct Cd. This deviation has been attributed to electronic effects at the Brillouin zone boundaries.2 The heats of formation of Ag-Cd alloys are essentially the same at 308", 723", and 800°K; consequently the temperature dependence of the heat of formation d?H/dT = ?Cp is vanishingly small, although from the exothermic heats of formation a negative value would have been expected. In the investigation reported here the heats of formation at 273°K of 6 silver-rich Ag-Cd solid solutions and the heat of formation at 78°K of 1 solid solution have been measured by tin solution calorimetry. The results are analyzed in terms of the quasichemical theory and the dependence of the heats of formation on temperature is discussed. The relative partial enthalpies per gram-atom of silver in tin at 541" and cadmium in tin at 532" and 541°K were obtained in the course of this investigation. The values of the temperature dependence of the relative partial enthalpies per gram-atom of silver in tin derived from the data reported by various investigators2,4-9 are contradictory. The literature contains only a value for 517°K of the relative partial enthalpy per gram-atom of solid cadmium in tin.2 EXPERIMENTAL PROCEDURES Samples of Ag-Cd solid solutions were prepared by melting weighed amounts of silver (99.99 pct pure) and cadmium (99.95 pct pure) in graphite crucibles under a flux of molten potassium chloride.10 The solidified ingots were sealed in evacuated Vycor tubes and annealed at 775°K for 10 days. The ingots were swaged and drawn into wires. The wires, sealed in evacuated Pyrex tubes, were held at 725°K for 5 hr and cooled to 365°K at an average rate of 2.5ºK per hr, followed by furnace cooling to room temperature. Chemical analysis of samples taken from different parts of each ingot gave no indication of segregation. Metallographic examination showed the samples to be homogeneous. Samples of the solid solutions or of the component elements were added to tin-rich baths in a calorimeter." At the start of a run the bath consisted of pure tin. Silver was used in the form of wire of 0.01-in. diam as supplied and cadmium in the form of lumps. Gold (99.999 pct pure) was added with the samples in order to reduce the endothermic heat effect of additions of Ag-Cd solid solutions. Samples of only one composition were added in a run and the ratio of the weight of alloy to that of gold was the same in all additions of a given run. In each run several calibrating additions of tin were made from 273°K. The heat contents of tin were calculated from the following equation, which is based on published data:12 (HTºK- H279º) = 6.70 T - 72,300/T + 20 cal/gram-atom; 505°K < T < 650°K The heat effect of each addition was plotted against the average of the sum of the atom fractions of solutes in the solution before and after that addition. The total concentration of solutes at the end of a run was less than 2 at. pct. In this range the heat effect was a linear function of the atom fraction of the solutes. The heat effect at infinite dilution and the composition dependence of the heat effect were obtained from the plots. RESULTS AND DISCUSSION Evaluation of Data. The linear dependence on composition of the heat effects of additions suggests that in the dilute range the enthalpy interaction coefficients other than the first-order coefficients of silver, cadmium, and gold are negligible, as shown in a concurrent publication.13 The heat effects at infinite dilution and the values of the composition dependence of the heat effects are listed in Table I.

Jan 1, 1970

By D. M. Blacknall, N. N. Winogradoff, E. W. Williams

Low-temperature measurements of photolumines-cence were used to evaluate the progvess in materials development. Variation of the impurity type, impurity concentration, and method of growth were used to clarify the chemical origin of defects in GaAs. Melt-g~ozun, epitaxial vapor-, and solution-grown samples were studied. A comparison of measurements at 77" and 20°K shows that more defects can be observed at the lower temperature. Th&apos;vee residual defects were identified in relatively pure GaAs. These were: silicon, copper, and a gallium vacancy-donor complex. Solution growth from a gallium solution inhibits the formation of the latter two. Eleven defects were studied and the "optical" activation energy of some of these, namely, silicon, cobalt, and chromium, has not been reported in the literature before. THE discovery of the injection laser in 1962 prompted extensive measurements of the photoluminescence of GaAs. The measurements were made at 77°K on GaAs doped with shallow impurities at various doping levels and compared with electroluminescence1&apos;2 and absorp- tion data.374 In addition, lower-temperature studies were made on relatively pure GaAS&apos; and on GaAs doped with oxygen,5&apos;" manganese,&apos; and copper.&apos; The observation of defects* in GaAs with photolu- *The word "defects" ~efers to both chemical impurities and native defects. minescence at low temperatures makes photolu mines-cence an invaluable tool in evaluating the progress in materials development. The only previous evaluation was done at 77°K when solution-grown and melt-grown GaAs were compared.O No identification of defects was made but it was shown that some of the deep-level luminescence seen in melt-grown GaAs was absent in solution-grown GaAs. The present work extends the comparison of preparation techniques to lower temperatures and to a study of epitaxial vapor-grown GaAs. It is particularly valuable for thin epitaxial layers since they cannot be analyzed by conventional analytical techniques. In addition, by varying the impurity type and impurity concentration the chemical origin and nature of defects in GaAs was demonstrated. Eleven defects were studied in all. Three of the defects were identified as residual defects which often contaminate GaAs prepared from the melt and the vapor. Only one such defect was observed in GaAs grown from a gallium solution and this was identified as silicon.

Jan 1, 1968

By R. M. Hudson

Equilibrium constants have been determined for the jeaction C (in steel) + H2O = CO + H2 as a function of carbon content (0.013 to 0.74 ujt pct) and temperature (1200° to 1800°F) by using a flow system in which the water-vapor content of various gas mixtures containing hydrogen, carbon monoxide, and nitrogen was systematically controlled. The equilibrium partial-pressure ratio K1 = PcoPH2/PH2O was obtained for two low-carbon steels and four Fe-C binaries from a series of runs made at each temperature. By comparison of Ki with the analogous ratio for the reaction C (graphite) + H2O = CO + H2, the activity of carbon in steel (ac) was comDuted for each temperature and carbon content studied. From these data values of the equilibrium constants for two other carburization-decarburiza-tion reactions of importance were estimated. The chemical compositions of the two steels and four Fe-C binaries used are given in Table I. Specimens of Steel E were cut from a 0.035-in.-thick commercially box-annealed and temper-rolled lot of a low-carbon low-metalloid steel. Steel F was a commercially hot-rolled rimmed steel that was cold-reduced at the Laboratory to a 0.059-in. thickness. Fe-C binaries A, B, C, and D were vacuum-melted and poured, hot-rolled, pickled, and cold-reduced at the Laboratory to furnish specimens 0.035 in. thick. Sheet specimens were cut from all lots to approximately 3/4 by 3 in. by gage and were vapor-degreased with trichlo-roethylene and weighed before heat treatment. Heat treatments were carried out in a hinged-top Hevi-Duty electric furnace with a Vycor-glass tube. When the furnace was at the desired

Jan 1, 1965

By A. A. Berk

LAGGING technology and the slow spread of information have been the chief obstacles to widespread participation in minimizing the industrial pollution load. These obstacles can be conquered by fact finding and applied research. There are three aspects to the problem of water-borne mineral waste: to minimize the amount being thrown away, to select a predisposal treatment, and to use the products or dispose of them. It is often possible to minimize the waste by making very minor changes in the process that produces it. For example, a manufacturer of automobile bumpers greatly reduced the dragout &apos;from a plating bath by modifying the design and position of two boltholes.&apos; A plater of automobile hubcaps installed a drainage bar and decreased the loss of chrome-plating solution to the rinse water by about 80 pct.&apos; The mill at a western mine found it possible to discard 60 to 70 pct of an ore with minimum treatment," so that the processing effort could be concentrated on a high-graded slime, with significant reduction in costs and improvement in recovery. The possibilities for waste reduction through process changes are limited only by the imagination. A recent patent points out the advantages of using No. 1 fuel oil instead of water in wet-process cement making;& the fuel oil presumably has better properties than water for this purpose and is said to be almost com&apos;pletely recovered or utilized, so that there is no waterborne waste. Recycling to reduce wastes and improve process economy is very well illustrated in vanadium and uranium recoveries from relatively low grade ore. Ores containing 6 pct calcium carbonate were found to give poor vanadium recovery by the salt-roasting process because the vanadium was converted to water-insoluble calcium vanadate. Following the salt-roasting process, sulfuric acid was used to leach the uranium. Enough calcium sulfate was formed

Jan 1, 1958

By E. P. Chartkoff, W. P. Sykes

In 1926 one of the authors published researches on the determination and description of the iron-tungsten and iron-molybdenum systems,&apos; including the equilibrium diagrams. In 1929, further work was carried on, including the examination by X-rays, which is recorded here. Meas-urements were made of changes in lattice parameters in the solid solutions. Precipitation from the solid solution and the accompanying changes in hardness were studied as well as the formation of the intermetallic com-pound phases upon sintering a mixture of metal powders. Materials All the specimens were prepared from the same quality of metals and by the same methods as were described in the determination of the constitutional diagrams. The metal powders as mixed and pressed were sintered or fused in a hydrogen atmosphere and subsequently treated as indicated in the titles of the figures. The formation of the iron-rich solutlon in the solid was accomplished by sintering in hydrogen for a period of 20 to 30 hr. at a temperature 25&apos; to 50&apos; C. below the melting point of the eutectic. The tungsten-rich and molybdenum-rich solid solutions of iron were prepared by adding the iron as a solution of iron ammonium oxalate to the oxide of tungsten or molybdenum, followed by a hydrogen reduction. This method results in a homogeneous alloy after sintering the pressed metal powder for 20 to 30 hr. at a temperature slightly below that of the peritectic reaction in the system involved. For X-ray examination the specimens were variously prepared, depending on the nature of the sample and what it was desired to show. For example, the iron containing tungsten or molybdenum in solid solution was cut with a file, the chips were put through bolting cloth, and this powder of filings formed the specimens for comparative study. The

Jan 1, 1930

By J. A. Ede

The object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. R. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mincs of the Illinois Zinc Co. Anticline and the Rock Formations Owing to the structural deformation between La Salle and Utica, the older rocks of the state are exposed to the surface along the northern embankment and the bottoms of the Illinois River valley near the latter place. At; the Illinois Zinc Co. works, Sec. 16, Tp. 33, R 1, a well for water mas sunk 1828 ft. and samples taken every 10 ft. of the ground penetrated; duplicates were sent to Mr. Cady of the Illinois Geological Survey. A general compilation or synopsis study of this section is here presented. As the well is over 1 mi. west of the Western limb of the anticline, the section affords some reliable data. These samples were studied and interpreted by H. M. DuBois as Lower Magnesian, and by G. H. Cady as the Lower Magnesian. The results are given in Fig. 3. The most interesting geological feature of this district is the La Salle anticline. In 1865, Leo les Quereux, looking at Split Rock, asked how it happened that the upper coal measures overlie strata of the Lower Silurian and what has become of the formations which are generally found intermediate—the Upper Silurian, the Devonian and sub-carboniferous, and the lower member of the coal measures?

Jan 1, 1920

By F. L. Toy, C. E. Sims

PNEUMATIC processes for converting molten pig iron to steel were the major producers of steel during the latter half of the 19th Century and until shortly after the turn of the century, when these processes began losing ground to their rival—the basic open hearth process. The first pneumatic process for converting molten pig iron to steel was introduced almost simultaneously by Sir Henry Bessemer in England and by William Kelley in the United States during the decade 1850-1860, but it was Bessemer who pushed it to a successful commercial operation. The process itself is so basically simple that it has not lent itself to many extensive or revolutionary improvements since its inception. During the first 30 yr, numerous&apos; designs of vessel and many modifications of practice were tried before the industry standardized on something resembling current practice. The evolution in construction has resulted in proportions and arrangements based more on mechanical expedience than on metallurgical requirements. Many of the early converters were stationary and had to be tapped similarly to the cupola or open hearth furnace. Such types were used for many years in Sweden and Germany, but the rotating or tilting types were favored in England and the United States. There was evident trouble with bottom tuyeres, becAuse about half of the early designs were constructed for side blowing with tuyeres submerged below the metal-bath surface. Even portable tuyeres, introduced from above, were tried. The principal advance, which made bottom blowing practical, was the invention, in 1863, by Henry Bessemer, and subsequent improvement by A. L. Holley, of a detachable bottom so that the tuyere section could be renewed. In the meantime, it was the demonstration, by Robert Mushet, of the value of manganese in overcoming hot-shortness in converter steel, that made the process metallurgically feasible. At first, only the acid practice was used, and Swedish pig iron, because of its low sulphur and phosphorus, was in great demand. The development of a suitable basic lining, by Sidney G. Thomas and Percy G. Gilchrist in 1876-1879, made the process applicable to the high-phosphorus ores of Europe. From the beginning of the use of the Thomas-Gilchrist process, trouble was experienced in obtaining sufficiently high temperatures in the blown metal, particularly in small heats. It is necessary, of course, to have the low-carbon blown metal at a considerably higher temperature for handling from vessel to ladle to molds than is needed for the molten pig iron. All of the increase in temperature in a pneumatic process must be obtained from the heat of combustion of the elements contained in the pig iron plus that from silicon when ferrosilicon is added. In bottom blowing practice, carbon is almost completely burned, but inasmuch as it cannot be oxidized to a higher state of oxidation than to CO when in contact with liquid iron, only a minor portion of the heat-producing capacity is utilized. Under such conditions, it is not considered to be an efficient source of heat. In the acid practice, therefore, silicon and manganese are the large heat producers, are quickly oxidized, and are efficient fuels. Too much manganese, however, thins the slag greatly and tends to promote excessive slopping or throwing of slag and metal from the converter during the blow. Most operators, therefore, like to keep the manganese content of the iron below 0.60 pct, and thus the main source of heat is the silicon, which must be at least 1 pct and sometimes 2 to 3 pct for small blows such as for castings. Ferrosilicon is sometimes added during the blow to obtain an adequate temperature level. In the basic (Thomas) practice, even more heat is required, because cold lime is added to flux the phosphorus after it is oxidized, and the basic slag must be maintained at a proper temperature. Silicon

Jan 1, 1951